Search Documents

By Paul L. Russell

Interest in the western oil shales of the US began in about 1908, with the first retort in Colorado constructed in 1917. The most successful early developments were near Elko, NV, where the Catlin Shale Products Co. produced more than 1.9 dam3 (12 000 bbl) of shale oil during 1920-1924 and at Rulison, CO, where a US government operation produced about 570 in 3 (3 600 bbl) of shale oil during 1926-1929. Plentiful low-cost crude oil was developed about this time and shale oil was of little or no interest until after World War II. From 1944 to about 1972, several companies, and the US government, operated shale oil mines and recovery plants in Colorado. While technical successes were achieved and an estimated 40-56 clam' (250 000-350 000 bbl) of shale oil were produced, economics were not favorable and commercial production was not achieved. In recent years domestic production of crude oil supplies has not kept pace with US consumption. The growing shortfall has been met with imports. The cost of imported oil has continued to escalate and increased US dependence on petroleum imports are national concerns, because of the negative impact on US balance of payments and an increasing dependence on other nations for US energy needs. In 1978, petroleum imports equaled about 44% of demand, up from 23% in 1970, but down from 48% in 1977 because of availability of Alaskan North Slope crude oil. Reduced domestic consumption and other factors have reduced current imports to about 40-45% of de¬wand-but at ever increasing cost. The growing shortage of crude petroleum and its increasing cost have resulted in renewed worldwide interest in oil shales. In the past, the main obstacle to oil shale development (progress toward commercial production) has been economics-shale oil cost too much to develop and thus could not compete with conventional petroleum crudes. Even with today's inflated energy prices, some experts say the production of synthetic crude oil from oil shale is, at best, marginally economic. The 1973-74 Arab oil embargo and increased crude oil costs-along with the federal government's offer to lease oil shale lands-resulted in renewed

Jan 1, 1981

By Jozef S. Stachulak

INTRODUCTION Conveyor belt fires represent a serious hazard in underground mines. This fact is well understood in most mining countries. The statistical data for Ontario mines (1) indicates that the majority of the conveyor fires occurred at the head pulley of the conveyor belt. The main emphasis for fire prevention and detection should then be concentrated at the drive pulley of the conveyor designed to transport non-combustible material. In the case of conveyor belt fires, it is of utmost importance to detect the hazard at an early stage, when the overheating has not yet reached the ignition point. Thermal noise detection sensors were installed in 1987 at several conveyor sites at Inco mines. PRODUCTS OF COMBUSTION THERMAL DEGRADATION OF CONVEYOR BELT Various investigations on conveyor belt fire hazards have been made in the past (2, 3, 4, 5, 6, 7). Several belt samples (6, 7) were subjected to thermal oxidative degradation. The belts used in these tests were neoprene, polyvinyl chloride and styrene-butadiene rubber (6). About 70 different compounds were identified in the volatile thermooxidative products. As expected, hydrogen chloride was the major toxic product formed, accompanied by relatively low quantities of other toxic compounds such as carbon dioxide, carbon monoxide, sulfur dioxide, carbon disulfide, hydrogen sulfide, benzene, chloroprene, cresols, chloroethanol, formic acid and C8 hydrocarbons. The research investigation (8) performed by the USBM indicated that "smoldering combustibles generate a very low level of CO compared to the level of smoke produced". The cited publication (8), states that, "During smoldering combustion, typical mine combustibles produce about 2.5 times more smoke than CO. As fires develop to their flaming stages, the trend reverses and about eight times as much CO is produced as smoke." The reader is referred to several significant sources of additional information pertaining to emission products that can be found in references (8), (9), and (10). ANALYSIS OF FIRE HAZARDS U.S.A. AND ENGLAND Nearly 15 percent of all underground coal mine fires in the United States involved ignition of conveyor belts (7). In many cases, the fires propagated through thousands of feet of belt entry and created losses in the millions of dollars. Some of these fires consisted of rubber belts. Some involved polyvinyl chloride and neoprene belts that were classified "fire resistant". Typically, a belt fire begins after the conveyor is stopped. The fire is initiated by burning coal dust and grease accumulation around defective rollers or belt drives that have become heated by friction (7). An analysis of 113 conveyor fires (11) showed that 41 originated at the driving pulleys, 32 at the defective rollers, and 40 elsewhere on the conveyor system. The severity of the fire, which can spread along a conveyor road, has been emphasized by the disaster at Creswell Colliery, Derbyshire, on September 26, 1950, when 80 men were overcome and killed by toxic fumes from the fire (12). The fire started from smoldering caused by friction, and developed into a flaming combustion, propagating along the roadway containing the rubber belt at an estimated speed of 40.2 m/s (90 mph), and travelling a total of 650 m (2100 ft) THE INFLAMMATION OF CONVEYOR BELTS THE MECHANISM OF IGNITION Defective operation of a conveyor belt may start a fire in several ways: - Friction of the belt on the drive pulley. - Jamming of a guide roller, and others.

Jan 1, 1991

By Neil and Associates

Seismic tomography is one of several additions to the suite of geotechnical engineering tools for use in various underground rock and mineral geologic structures. Seismic tomography is a method for reconstructing a cross section of an object based on attributes of seismic energy that have been transmitted through the object. The in-seam seismic tomogram provides a dataset that can be graphically portrayed in a color-coded format that is then used to infer relative stress concentration (Fig. 1). During the past several years, the US Bureau of Mines (USBM) at its Denver, CO and Twin Cities Research Centers in Minnesota funded several innovative hardware and software developments. These were directed toward use of in-seam seismic tomography for underground geologic strata evaluations. These preliminary investigations have matured into well-defined and field-proven technical advances for improving ground-control decision making in the mining industry.

Jan 1, 1996

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.

By R. A. Williams

The Pascua Lama Project is situated on the border of Chile and Argentina at an elevation of 4,800 m. The ore contains gold, silver and copper, and an initial milling production rate of 33,000 t/d is planned. The mineralogy of this deposit is unusual. The ore is hard and abrasive, and it contains a complex array of sulphate minerals, such as chalcanthite, jarosites and alunites. The sulphides are predominantly enargite and pyrite. A novel flowsheet has therefore been developed, which includes dry grinding and ore washing to remove and then neutralize the soluble salts, prior to flotation, cyanide leaching and Merrill-Crowe recovery of the precious metals. These metallurgical issues and challenges associated with plant design and construction in the high and remote Andes Mountains make this a particularly challenging project.

Jan 1, 2001

By William G. Pariseau

Solvay Chemicals Company mines trona in south-central Wyoming and has done so for many years. The mine is one of several in a mid-continent sedimentary basin that hosts the largest trona resource in the world. Trona is an evaporite, a sesquicarbonate that occurs in several seams of varying thicknesses and depths. Trona is processed into soda ash which has a number of industrial uses in the manufacture of glass, detergent, paper and chemicals. Figure 1 shows the location of the Solvay Mine. A ventilation shaft was recently excavated at Solvay Chemical Company’s mine in the trona patch. In fact, a 22 ft (6.7 m) diameter shaft (inside diameter) was bored upwards from the 1500 ft (457 m) level to the surface. The first bored section was 26 ft (7.9 m) in diameter that allowed for a 2 ft (0.6 m) thick concrete liner. This section began at a depth of approximately 1500 ft (457 m). A second bored section was 24 ft, (7.3 m) in diameter that allowed for a 1 ft (0.3 m) thick concrete liner. This section began at a depth of approximately 750 ft (229 m). This shaft is the #5 Shaft. Figure 2 shows the cutter head used to excavate the shaft.

Feb 1, 2025

By L. M. Kocher, J. R. Heberger, J. P. Pollard, M. F. Nasarwanji

Injuries associated with hands and fingers are highly prevalent in mining and identifying factors associated with these injuries are critical in developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011–2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53%) followed by bone fractures/chips (26%). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals (pipe, wire, guards) and hand tools as the primary sources of hand and finger injury. Although information on glove use was limited, leather gloves were most often worn when an injury occurred. When worn, gloves were found to contribute to 20% of the injuries, indicating their potential to protect the hands, but also potentially put the hands at risk. Further research is necessary to determine performance requirements for gloves used in mining operations, specifically those offering cut and puncture resistance.

Mar 2, 2022

By Verya Nasri, Agustin Rey

Once completed, the Montreal Réseau Express Métropolitain (REM) will be the fourth largest automated transportation system in the world. The REM represents construction costs of approximately 7.0 billion Canadian dollars. The project consists of 67 km of twin tracks over four branches connected to downtown Montreal. The project includes 26 stations with 3 underground stations in downtown Montreal. One of the underground stations was built using the NATM method with thin permanent shotcrete initial and final liners separated by a sprayed on waterproofing membrane. The 2 other underground stations were built with the cut and cover approach including one using permanent secant pile wall with permanent walers and struts as the support of excavation and the final perimeter wall of the station. The project also includes the rehabilitation and enlargement of the Mont Royal Tunnel. This 100-year-old double track tunnel is about 5 km long. The REM also consists of 3.6 km new TBM tunnel connecting downtown to the Montreal International Airport through saturated soft ground and karstic rock. By the time of RETC, the construction of REM underground structures will be completed. This paper presents the design and construction aspects of the underground structures of this mega project.

Jun 13, 2023

By Martin Langenderfer, Catherine Johnson, Alexander Douglas

Mine haul roads degrade rapidly due to extreme loads on suboptimal construction materials. Unmanned aerial vehicles (UAV) are suited to quantify large-area road-network conditions, such as surface roughness, defects and grade to optimize remediation of poor conditions and reduce overall costs. Mine haul roads present unique challenges, such as material type and edge characteristics, to automatic road detection that often fails, requiring manual road input. This research work proposes a new method using the road center determined by the principal curve of a haul truck’s path. Analysis grids were created from this center line. A dense point cloud from UAV photogrammetry was generated and multiple linear regression analysis was conducted on each individual grid. The root-mean-square error in each grid indicates the surface roughness, and the change of slope between grids indicates the road grade inconsistencies. This method was applied to 26 road sections, and the results were validated by images taken from the truck operator’s vantage point. Critical defects were identified including excessive pothole formation, corrugation, depressions retaining water, and narrowing of travel lane. The results demonstrate this is a valid method of road identification and quantification of road defects at a mine site.

Apr 1, 2024

By P. Zhang, S. Al-Thyabat

"Phosphate rock contains traces of rare earth elements (REEs) and can be a secondary source of these critical materials as large tonnages of phosphate rock are mined annually. Attention has mostly focused on the extraction of REEs from phosphogypsum, which contains more than 70 percent of the REEs reporting to phosphate concentrate, with only limited work conducted on REE extraction from sand tailings and slime even though they account for 16 percent and 15 percent, respectively, of REEs mined with phosphate matrix.In this work, phosphate flotation tailings were upgraded by gravity separation and froth flotation. Gravity separation was conducted using a laboratory shaking table, while flotation was conducted in a Denver D-12 flotation cell. The concentrated tailings were then leached by nitric acid followed by REE extraction with solvent and ion-exchange resin.The sand tailings were assayed as having 2.6 percent phosphate (P2O5 ) and 198.1 µg/g REEs. It was found that the shaking table could produce tailing concentrate assayed as having 8.6 percent P2O5 and 616 µg/g REEs but with only 20 percent REE recovery, while the froth flotation produced froth concentrate assayed as having 8.1 percent P2O5 and 368.2 µg/g REEs with 63.5 percent REE recovery. Leaching the flotation concentrate with 5.2 M (25 percent) nitric acid followed by extraction with solvent and ion-exchange resin yielded precipitates with REE contents of 0.926 and 0.314 percent, respectively, compared with 0.716 and 0.213 percent when table concentrate was used.IntroductionRare earth elements (REEs) consist of a group of 17 elements: the 15 lanthanides along with yttrium (Y) and scandium (Sc). They are rare not because of their scarcity in the Earth’s crust but because they are rarely found in economic and mineable deposits. REEs are called “seeds of technology” because of their importance to some critical technological industries such as renewable energy, hybrid cars, electronics and batteries. On average, an electric car or a hybrid car contains about 10 kg of REEs (Grasso, 2012; Radhika et al., 2011).REEs are usually categorized into light (LREE) and heavy (HREE). LREEs consist of lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pr), samarium (Sm), europium (Eu), gadolinium (Gd) and scandium (Sc), while HREEs consist of terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), lutetium (Lu) and yttrium (Y). About 200 minerals contain traces of REEs, but only three are considered economically significant: bastnasite, with the formula La,Ce(CO3)F; monazite, with the formula(Ce,La,Nd,Th)PO4; and xenotime, with the formulaYPO4 (Jordens, Cheng and Waters, 2013)."

Jan 1, 2016

By Dale Matthews

The Getchell Mine, near Winnemucca, NR, was discovered in the 1930s and was initially mined to recover gold from oxide ores. During the 1940s and 1950s, gold was recovered from the highly refractory arsenic sulfide ores using horizontal kilns to roast the ores. During the 1960s, fluid bed roasters were used to oxidize the ore and recover the gold. The mine was shut down from 1968 through 1985. In 1985, heap leaching was started on the low-grade oxide ores that were available. In 1989, a pressure oxidation circuit was started to recover gold from the higher grade sulfide ores. Flowsheet The basic plant flowsheet of the Getchell Mine are shown in Figs. 1 and 2. The plant was designed to process a nominal 2.7 kt/d (3000 stpd) of ore with about an 85% onstream availability and a gold production of 15.5 kg/d (500 oz/ day). Run-of-mine (ROM) ore is fed directly to a wet semiautogenuous grinding (SAG) mill after the +457-µm (+18in.) rock is removed on a stationary grizzly. From the SAG mill, the ore goes to a ball mill where it is ground to 80% -75 µm (-200 mesh) and is then sent to a thickener. The SAG and ball mill operate in closed circuit using cyclones.

Jan 1, 1994

By David Smith

Construction of a new transportation link frequently requires crossing under an existing highway or railroad. Although traffic diversions may permit a cut and cover structure to be built, ‘zero impact’ tunnel solutions are becoming increasingly popular. The vertical clearance between the new tunnel structure and the existing highway or tracks may be very low; sometimes less than two meters. This leaves little room for error since any ground loss can rapidly translate into surface settlement. Problems can be avoided by maintaining the stability of the tunnel face and by minimizing ground movement around the tunnel lining. This paper examines construction methods that have been used to construct short tunnels with shallow cover, and highlights factors to be considered for future projects.

Jan 1, 2005

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of 12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Feb 24, 1997

By Robert C. Speck

The U.S. coal industry has long utilized the pillar-extraction mining technique as a method for maximizing coal recovery. Like longwall mining, it causes large-scale movements that progressively propagate from mine-level to the ground surface and may affect the groundwater regime, surface drainage and surface structures. The U.S. Department of Energy, in an effort to foster in- creased use of total extraction mining techniques, has recognized the need for a better understanding of these movements that will lead to a greater compatibility between coal mining and present and future land use. As part of that goal, GAI Consultants, Inc. is currently in- stalling instrumentation to monitor the ground movements associated with pillar extraction mining at Kitt Energy Corporation's No. 1 mine in northern West Virginia.

Jan 1, 1982

By D. L. Langhans

Platinum-group metal (PGM) converter matte from the Stillwater Complex, MT, was subjected to chemical and biological leaching in an effort to upgrade the matte by decreasing the Cu and Ni content. Copper and NL extractions were optimized in a two-stage chemical leach. Atmospheric pressure sulfuric acid leaching removed over 90 pct of the Ni and Fe in the first stage, while 95 to 98 pct of the Cu was removed is the second stage using an acidified cupric chloride leach. This two-stage leach, followed by an elemental sulfur removal step, decreased the weight of the matte by 90 pct. The combined Cu and Ni content was reduced from 65 pct to less than 20 pct, while the PGM content was increased from less than 2 pct to 26 pct. Biological oxidation using Thiobacillus ferrooxidans also proved to be an effective method for removing Cu and Ni. Over 90 pct of the sulfide was oxidized and 99 pct of the Cu and Ni were solubilized, leading to a 60 pct reduction of sample mass during the 17 week bio-oxidation of the Stillwater converter matte. The final residue, after removal of jarosite that accumulated during bio-oxidation, contained less than 3 pct combined Cu and Ni and 6 pct MM.

Jan 1, 1993

By S. R. Titley

Carbonate-hosted massive sulfide (60%) ores of the western Cordillera compose a distinct class of deposits although they vary widely in detail and perhaps genesis. They have been important sources of lead, zinc, copper, silver, gold, and more rarely, molybdenum, tin, and tungsten in complex mineral assemblages usually dominated by pyrite. They occur as concordant stratiform bodies, as discordant mantos, and as chimneys crossing tens of meters of section; many are associated with faults and breccia bodies. Environments of formation of carbonate hosts range from craton basin to shelf with ages from Proterozoic to Cretaceous; in many instances, dating has shown mineralization to be significantly younger than hosts. Temperatures of formation determined for many deposits are high (200°-400°) and many districts are centers of igneous activity manifested by dikes, sills, and stocks. However, direct cause and effect relationships have been difficult to establish. Many important problems attend the renewed interest and study of these deposits and include questions of metal-sulfur sources, metallization processes and histories, geological controls at all scales, and relationships to broader patterns of metallogeny.

Jan 1, 1985

By James J. Scott

I welcome this opportunity to speak before the Coal Division of the AIME in such an attractive setting as the Pacific Northwest. With the development of the Centralia project, the Pacific Northwest will have its first major coal-fired thermal electric generating plant. This State has a long history of coal mining that diminished with the passage of coal-fired steamships and locomotives but is now reviving with the growth of electrical power demand. Because this 1,400 row plant is to be supplied with surface-mined coal, it is particularly appropriate that this area be the setting for a talk on factors influencing the growth of surface coal mining in the West. During the course of my talk, I will touch on a number of factors including electric power demand, coal resources, production trends, environmental considerations and trends in State and Federal activities that I feel will influence surface coal mining in the West. Total electric power consumption by the year 2000 is expected to reach 9.4 trillion kilowatt-hours. Predictions of total coal consumption for electric power generation by that year range from a low of 845 million tons to a high of 1,520 million tons, or 2.6 to 4.7 times the amount used for this purpose in 1970.

Jan 1, 1971

By William S. Hallager

Banded ironstone and associated fine-grained carbonaceous sediments near Jardine, Montana, are enriched in gold, arsenic, and tungsten. The mineralized sediments lie within a thick sequence of quartz-mica schists cut by a 2.6 b.y, granite. Surface, underground, and drill hole mapping are used to construct structure contour maps of individual ironstone lenses. Each lens is then unfolded by triangulation of minimum surface path distances between drill hole penetration points. Major and minor element abundances in composite ironstone samples are interrelated through R-mode factor analysis. Results indicate five significant element groupings thought to reflect coarse detrital, fine detrital, sulfide-rich chemical, iron-rich chemical, and epiclastic ultramafic sediment. Ultramafic factor scores are highest in a previously undefined rock type rich in cummingtonite, biotite, and chlorite; lacking in quartz; and closely associated with at least one ore horizon. Detrital dilution of ironstone, calculated from chromium and nickel content, drops off significantly as ore-bearing ironstone is approached. This observation may indicate that centers of gold precipitation have protected themselves, either topographically or by rapid deposition, from detrital contamination. Gold mineralization correlates most strongly with the sulfide- rich factor. Gold may have been introduced through hotspring activity as a bisulfide complex.

Jan 1, 2013

PolyMet Mining is developing the NorthMet property near Duluth, MN. Laboratory investigations have led to the development of the Platsol process to dissolve in one step the base metals (copper and nickel) as well as the gold and platinum group metals (PGM). To complete the prefeasibility study, a fully integrated, 10-day pilot plant trial was undertaken. The trial consisted of high-temperature (>220ºC or >428ºF) pressure oxidation in the presence of 5 to 10 g/L chloride (the Platsol process). This was followed by solid/liquid separation, gold plus PGM recovery from solution, conventional copper solvent extractions/electrowinning (SX/EW) and recycling of the copper raffinate to the autoclave. The concentrate tested during the trial period was a NorthMet bulk flotation concentrate. It assayed 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t (0.041 oz/st) Au, 2.2 g/t (0.064 oz/st) Pt and 9.9 g/t (0.289 oz/st) Pd Laboratory results were confirmed and, with minor adjustments of the laboratory Platsol conditions, the following leach extractions were obtained during the pilot plant trial: 99.6% Cu, 98.9% Ni, 96% Co, 94.6% Pd, 96 % Pt and 89.4 % Au.

Jan 1, 2003

By Robert E. Gray

The vat leaching operation at the Yerington Mine was started in October, 1953. The original plant facilities consisted of primary and secondary crushing, eight leaching vats, precipitation launders, sulfuric acid plant and the necessary maintenance, warehouse and administrative facilities. By 1961, 35,000,000 tons of oxide ore had been removed from the mine exposing the underlying sulfide ore body. A 5,000 ton per day concentrator was constructed and put into operation to treat the sulfide ore in November, 1961. The original crushing plants were used for both oxide and sulfide ores. By adding a third crushing shift for six days per week, the treated ore was increased from 12,000 to 17,000 tons per day. To balance the oxide and sulfide ore reserves, the concentrator was expanded to 13,500 tons per day in 1967. Again, no additional crushing facilities were added. It was anticipated that the treatment rate of oxide ore would be reduced from 12,000 to 9,000 tons per day. Instead, the addition of two crushing shifts per week, and improved operating procedures, increased the treated ore to 26,500 tons per day, 13,000 tons to the vat leaching and 13,500 tons to the concentrator.

Jan 1, 1975