Search Documents

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,500 tons of ore per day with an average gold grade of 0.34 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, a long-hole stope and cut-and-fill mining methods are used at the deposits which are divided into several mining zones. Cemented rock fill (CRF) is used as the backfill in the open stope. CRF design includes the aggregate design, the ratio of cement and fly ash design, and strengths for the long-hole stope and cut-and-fill. In the aggregate design, the particle size distribution is one of the most influential aggregate characteristics in determining how it will perform as a basic backfill material. Gradation helps determine durability, porosity, cement and water requirements, strength, and shrinkage. To cut the backfill cost, fly ash usually is added into the binder to replace some part of cement. However, adding fly ash can affect the strength of the backfill. The reasonable percentage of fly ash is also important for making a good and low cost backfill. Based on the different mining method, the different backfill with different strength is designed. A systematic quality control procedure for aggregate and backfill is followed. After four yeas application, CRF system in Leeville achieved very good results.

Jan 1, 2011

By Nikhil Dhawan, Shrey Agrawal

Feldspar, a low-alumina, and abundantly available aluminosilicate source, is explored in this study to extract aluminum and potassium values. The sample comprises lamellar layers of microcline and albite with quartz containing 17.4% Al2O3, 9.67% K2O, and 66.3% SiO2. Mechanical (milling) and thermal (alkali and acid baking) activation are investigated, followed by HCl leaching. The milling treatment up to 6 h is inefficient in phase dissociation and results in ~ 40% Al and K dissolution. The alkali thermal treatment yielded 80% Al and 71% K extraction. Direct precipitation of the dissolved Al and Si values yielded alumina purity of ~ 29%, and silica gelation separated SiO2 and improved alumina product (94% purity, 71% recovery). Acid baking yielded 98% pure alumina precipitate; however, Al and K extraction were limited to ~ 45% and 65%, respectively. The microwave-assisted alkali treatment was optimal with 800 W and 10 min processing conditions yielding 80% Al and 71% K recovery with 2.26 kWh/kg alumina of thermal energy consumption. The final product contains γ-alumina with a specific surface area of 87 m2/ g. Keywords Feldspar · Alumina · Potassium ·

May 18, 2022

By Zhonglin Ye, Guangping Dai, Ba Zhang, Yonggang Wei, Shiwei Zhou, Bo Li, Hua Wang

Decreasing copper content in slag is critical for improving copper recovery, where apparent viscosity is the main factor affecting the separation of matte/copper from the slag. The viscous behavior of copper converter slag was investigated during reduction process in this paper, and its non-Newtonian viscous behavior and shear thickening characteristics were clarified. The effects of silicate structure and solid particles in the melt on the slag apparent viscosity were investigated. As slag cleaning proceeded in an electric furnace, the magnetite gradually transformed into ferrous oxide, increasing the FeO/SiO2 ratio. With this ratio increased from 1.2 to 2.0, the slag structure was simplified, and its apparent viscosity decreased from 0.26 to 0.12 Pa·s at 1523 K. The iron phase was excessively reduced to metallic state; the slag contained metallic copper-iron alloy particles, increasing apparent viscosity. The apparent viscosity and phase structure of the slag corresponding to the iron phase reduction process were analyzed in detail; the results obtained in the present study are of great significance to the reasonable control of the converter copper slag cleaning process.

Nov 7, 2022

By N. Arbiter, C. C. Harris

The economic advantages of large diameter ball mills can be compromised by unexpected capacity limiting conditions. These arise because media rotational flow to ore axial flow ratios, and the number of mill revolutions that ore is subjected to during residence, are both inversely proportional to mill diameter. Because of this, mixing efficiency and grinding kinetics may decrease and become capacity limiting when mill diameters reach a critical range. There are two possible scale-up problems involved in the design and use of mineral processing machinery: • Selecting the size and operating conditions for available larger equipment, to insure that operating results will match those obtained with smaller units; or •Extending the size ranges of equipment beyond existing limits. Previous research at Columbia University into flotation machine hydrodynamics has demonstrated the importance in scale-up of internal flow relationships; these perform a similar role in grinding (Arbiter and Harris, 1980).

Jan 1, 1982

By Grant P. Cordon

Our subject, "Safety, Legal, and Contracting," is a range of topics which covers a broad spectrum, but is obviously Intended to focus our attention upon certain particular aspects of tunnel problems. These are all fascinating and complex subjects, and others are much more qualified to discuss to discuss the fine points involved. Put after some 45 years' involvement as an inspector, engineer, contracting officer, and especially for the last 22 years as a contractor's estimator and manager, I have developed some strong and definite convictions to share with you. I hope it will serve to get you started thinking. My first tunnel experience was in a soft ground tunnel which was dug by hand, literally. The crown or arch back was taken out, a pebble at a time, by bare hand. The face was constantly breast-boarded, and the mucking was all done by hand shovel. My first rock tunnel was drilled by hand held drifters from the muck pile. Since then, most tunneling techniques have improved greatly. The jumbos, booms, muckers, and moles have taken over many of the back-breaking chores, and reduced the manpower requirements.

Jan 1, 1974

This paper describes major technical developments in rod mill design and operating practice since its introduction into the North American minerals industry over fifty years ago. The basic operating characteristics of the wet, overflow rod mill are described, and significant operating variables are reviewed in terms of their effects on mill power draw, power efficiency, and practical aspects of circuit operation. Key factors for improving the economic performance of rod milling circuits are identified.

Jan 1, 1986

By Aki Fujii, Hiroshi Dobashi, Mitsuro Matsuda, Yoshinari Kondo

INTRODUCTION The Metropolitan Expressway Central Circular Route with a total length of approximately 47 km is located outside the Inner Circular Route of Tokyo (at a radius of approximately 8 km from the city center). Sections with a length of approximately26 km, slightly less than 60% of the total length, on the east and north sides are in ser-vice. Completing the Central Circular Route (Figure 1) is expected to enable through traffic concentrated at the city center to get around, and to form a well balanced trans-port network, which will alleviate traffic congestion considerably. The Central Circular Shinjuku Route, a section with a length of approximately 11 km on the west side, is now being constructed at a fast pace. The route is being built mainly by the shield tunneling method to carry out work smoothly under a trunk highway carrying heavy traffic and to reduce adverse effects of tunneling work on residents in the neighborhood. Shield tunnels have recently been becoming longer and deeper, and no secondary linings have been used in an increasing number of cases because of the over-crowding of cities or the reduction of budgets for public works. Economical, durable and high-quality segments have been required for linings of shield tunnels. Segments are made of concrete, steel, cast iron or combination thereof. Concrete segments are generally used in shield tunnels of medium to large diameter. Concrete segments are highly durable and resistant to compression, so they are highly resistant to earth pres-sure, water pressure and jack thrust. They are, however, heavy and have low tensile strength, so they are brittle and their corners are likely to spall. Concrete segments should therefore be handled carefully.[1] The authors have developed a steel fiber reinforced highly flowable concrete segment (referred as SFRC segment) that overcomes the weaknesses of concrete segments[2] to construct economical, durable and high-quality linings. SFRC segments have been applied to outbound sections SJ51 through SJ53 of the Central Circular Shinjuku Route. Unlike conventional concrete segments (referred as conventional RC segments), SFRC segments are made of steel fiber reinforced self-compacting highly flowable concrete. SFRC segments require less reinforcing bars than conventional RC segments because steel fibers are expected to work as reinforcements. Steel fiber reinforced concrete is a composite material that overcomes the brittleness of plain concrete, and has higher resistance to bending, tension and shear than

Jan 1, 2007

By Evan J. Owen, Virginia T. McLemore

The Zuni Mountains, located in Cibola County, New Mexico is an uplifted area that exposes Proterozoic igneous and metamorphic rocks overlain by Permian and younger sediments. Sedimentary-hosted Cu deposits and fluorite veins in the district have recorded production, but other deposits exist. Proterozoic ultramafic rocks may host Ni and PGE. A recent regional stream sediment survey collected 76 samples as part of an exploration geochemistry course at New Mexico Tech with the goal of assessing the critical minerals potential of the district. Whole rock and trace element chemistry of the sediment samples (<2 mm) show a variety of critical minerals possibly worthy of future targeted exploration including up to 700 ppm As, 2100 ppm Ba, 26 ppm Bi, 25 ppm Co, 640 ppm Cu, 145 ppm Ni, 110 ppm Sb, 170 ppm V, and 500 ppm Zr. Positive correlation between Bi, As, Cu, and Sb suggest that these critical minerals are found together within copper veins related to shear zones in the district. Samples collected from streams that drained outcrop of mafic and ultramafic rocks were found to generally contain more Ni, Co, and V. Samples elevated in Ni will be reanalyzed for PGE.

Feb 1, 2025

Newmont Gold&apos;s methods for deposit modeling vary, depending on geology, mining and processing methods, economic feasibility and availability of historical information. It is argued that successful modeling requires understanding these factors, knowing the strengths and weaknesses of the various modeling techniques and being flexible in selecting the appropriate methods. Newmont is one of the world&apos;s largest gold mining companies, with operations in the United States, Peru, Mexico, Indonesia and Uzbekistan. And it is active in exploration worldwide. At the end of 1996, Newmont declared a total reserve of 1.15 equity kt (37.1 million equity oz) of gold and 2.17 equity Mt (2.39 million st) of copper. The gold deposits managed by Newmont totaled 752 Mt (829 million st) of ore containing 1.28 kt (41.3 million oz) of gold averaging 1.71 g/t (0.05 oz/st). In addition, Newmont is developing a porphyry copper-gold deposit that totals 9.1 Gt (1 billion st) of ore containing 380 t (12.1 million oz) of gold and 4.82 Mt (5.32 million st) of copper. (In May 1997, Newmont Gold Co. merged with Santa Fe Pacific Gold Corp., thus increasing Newmont&apos;s reserves to 1.72 kt or 55.2 million oz of gold and 2.17 Mt or 2.39 million st of copper.)

Jan 1, 1998

By B. Gigas, M. Preston, M. Giralico

Optimized mixer settler designs will now handle total flows of over 6,000 m3/hr.Computational Fluid Dynamics (CFD) is a timely and predictable tool for design development. Lightnin has the capability of using numerical analysis methodology to evaluate flow patterns and phase separation. CFD can show performance differences between changes, in mix tanks, in settler geometry, and in liquid depth, against variable flow rates. Understanding the differences allows the development of optimized designs. This paper focuses on the major design components of the mixer settler and how technological advances will lead to further improvements, when designing for today’s largest flow plants.

Jan 1, 2004

By George Wilson

When pumping abrasive slurry mixtures, special attention must be given to pump design and construction. The second article in this two-part series describes some design features to consider when selecting centrifugal slurry pumps. Hydraulic Design Most centrifugal pumps are conventionally designed to achieve the desired hydraulic performance at the highest efficiency and lowest cost when handling clear fluids in reasonably clean environments. Manufacturing limitations are not imposed on the configuration of the pump, since conventional materials such as cast iron, bronze, and stainless steel are used. Manufacturers and buyers usually select the highest specific speed commensurate with the lowest cost attainable. Part life is almost infinite. When a centrifugal pump is designed for slurry service, the important factors in pump design are wear and materials of construction; size and efficiency assume lesser importance. The pump must operate at low rotational speed and the impeller has to be a truly radial flow design. These factors immediately determine that the pump must be of a low specific speed design in the range of 600 to 1800. The specific speed is a type number that is constant for all geometrically similar pumps; it designates the geometry of the impeller and casing. [ ] where n = rpm, Q = flow (US gpm), H = total head (ft), and Ns = specific speed. Since wear is a function of velocity it can be shown that for a given head and capacity, wear will increase with increased Ns. Centrifugal Pump Casing The casing has a profound effect on performance. If designed incorrectly it can destroy a large part of the energy given to the flow by the impeller, resulting in low efficiency, high hydraulic forces, and excessive wear on both the casing and impeller. In a conventional spiral volute, the static pressure around the impeller is uniform only when there is a free vortex velocity distribution in the volute, i.e., when the spiral flow from the impeller coincides with that of the volute spiral. This occurs only at the best efficiency point (BEP), between the pump&apos;s best operating zone and over capacity zone. Departure from the free vortex velocity distribution in the volute at partial or over capacities produces circumferential pressure gradients at the impeller periphery, which is directly proportional to the specific gravity of the mixture being pumped. At partial or over capacities, the flow will not tolerate the abrupt deflection at the tongue and severe energy losses and wear are created near the casing throat and on the impeller. Concentric and semi-concentric volute designs produce uniform static pressures at the impeller periphery and make the pump, much less sensitive to "off"&apos; BEP operation. Hydraulic forces and wear are considerably reduced-eliminating the tongue prevents abrupt deflection of the flow, turbulence is minimized, and the velocity in the casing volute and throat is reduced. Good efficiency is sustained over a wider operating hand. Casings of this design are easy to cast. • Spiral volute (conventional)-Radius to the outer periphery of the casing and the volute area constantly increases. • Semi-concentric casing-Radius to the outer periphery of the casing and volute area remain constant within a certain angle. • Concentric casing-Radius to the outer periphery of the casing and volute area remain constant through 360°. The degree of concentricity must be reconciled with efficiency, hydraulic radial load, and wear for each specific speed chosen. Up to 1200 Ns the casings can be fully concentric without sacrificing too much efficiency. Above 1200 Ns, the casings can be semi-concentric. The angle of concentricity

Jan 10, 1981

By M. A. Trevits

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

Jan 1, 2009

Narrow vein mining, with enough challenge and also where the cutting edge technology can be applied, is still a very important and exciting portion of the mining industry. Based on the deposit characteristics, the most flexible mining method, cut and fill, has been being tested mining this high grade Northern Nevada property, Hollister, since the year of 2008. In the last three years, 254,000 tons of ore were hauled out of the portal and 23,000 feet of development were excavated underground with the winning of several safety and environmental awards. Together with mine geology, the essential segments include mining cycle, ground control, ventilation, grade control and backfill method in cut and fill stopes were covered in this paper.

Jan 1, 2012

By Y. Q. Zhang, Y. Luo, S. S. Peng, C. T. Holland

Barrier pillars in underground coal mines could eventually be subjected to a hydraulic pressure head due to the build-up of mine water in the old workings. The pressure head could not only act as a force to destabilize the pillar but also cause seepage flow through the pillar and its surrounding strata. Excessive seepage flow could induce piping failure that in turn could accelerate the mechanical failure process of the barrier pillars. In this paper, finite element simulation approach has been employed in the evaluation of the barrier pillars. Both the stress distribution and the seepage flow pattern in and around a barrier pillar have been simulated numerically. The effects of ground stress on rock permeability to water seepage has been taken into consideration in these simulations.

Jan 1, 2001

By William R. Yernberg

The combined 75th Annual Minnesota Section of SME meeting and 63rd Annual University of Minnesota Mining Symposium was held April 9 and 10, 2002, in Duluth, MN. This year’s theme was “Keys to the Future: Imagination, Innovation and Technology.” The meeting consisted of plenary and technical sessions and a special General Manager’s Session. The technical paper presentations included concurrent mining and mineral processing sessions. In the General Manager’s Session, representatives from the region’s taconite operations presented the current status, concerns and future plans for each of their operations.

Jan 1, 2002

South Africa?s primary electricity supplier, Eskom, provides incentives to reduce power demand during critical times by granting capital through a Demand Side Management programme. DSM encourages the end user to review and optimize energy consuming systems and use capital, provided by Eskom, to purchase or modify the equipment required to achieve a load-shift. As part of the DSM agreement the mine ultimately acquires the capital equipment and benefits from reduced power costs, but in return is required to sustain the load-shift tactic for up to five years. The paper focuses on one DSM tactic, main fan energy management. In this case, reduced air flows during selected peak and off peak periods, results in a substantial reduction in peak power demand. DSM incentives provided capital for automated main fan control as well as improved control of the mine ventilation systems. To examine the work in detail Gold Fields Ltd Driefontein gold mine near Johannesburg was chosen as a case study.

Jan 1, 2009

By VIVEK KASHYAP, Evody Tshijik Karumb, PATRICK TAYLOR

The partial reduction of zinc ferrite to zinc oxide and iron (II, III) oxide can enhance the leaching rate of zinc. Zinc ferrite has often been found as a major component of zinc residues and electric arc furnace dust. The Waelz process is an existing process for zinc ferrite processing, which requires a temperature of more than about 1200 °C to produce Waelz oxide containing ZnO. Since zinc residues have been deemed as a potential way for the extraction of zinc and other critical metals, it is important to analyze the reaction kinetics in the temperature range of interest. This manuscript discusses the chemical kinetics of zinc ferrite reduction by hydrogen gas. Several researchers studied the reduction of zinc ferrite with CO; however, unlike CO, the use of H2 gas as a reductant allows partial reduction of zinc ferrite even at low-temperature range (400–600 °C). Thermogravimetric analyses (TGA) experiments were performed in the temperature range of 300–700 °C with 10% and 30% H2, and the data obtained was analyzed using the isoconversional method of kinetic analyses. The standard models used for isoconversional kinetic analysis were chosen from literature and experimental data were fitted to determine the controlling mechanism and calculation of kinetic parameters of reduction of zinc ferrite. The rate of reaction was found to be increasing with an increase in temperature and partial pressure of H2 gas. The reaction could be divided into three stages, where reaction interface contraction was found to be the controlling mechanism at the initial stage of reaction. As the reaction proceeds, product layer thickness increases, and thus, diffusion was found to be the controlling mechanism. Roasting products obtained from TGA experiments were also characterized using a scanning electron microscope (SEM) to verify critical morphological details.

Jul 26, 2022

By W. K. Katoto

The Tailings Leach Plant (TLP) of the Zambia Consolidated Copper Mines Ltd at Nchanga was commissioned in 1974 as the world&apos;s first largest successfully operated agitation leach SX-EW plant for copper production. The design, development and operation of the plant soon after commissioning termed as TLP stage II has been described by Holmes et al (1). In the initial phase the plant was designed to treat approximately 25,000 tonnes per day of current flotation tailings from the Nchanga Concentrator operations, and had a design capacity to produce 75,000 tonnes per annum of copper. Further expansion took place in 1986, and TLP stage III was successfully commissioned to treat an additional 20,000 -25,000 tonnes per day of large reserves (over 135m tonnes) of reclaimed tailings stockpiled since the early 1930&apos;s in four paddock type tailings dams (T01 to T04). The salient feature of TLP stage III expansion described by S K Mwenechanya et al (2 -3) was the installation of the world&apos;s largest Horizontal Belt Filter Plant with 26 filters each of 80 m2 filtration area.

Jan 1, 1996

By N. Wahl, D. M. Blackketter, R. Thornton

This paper evaluated using a water-filled abandoned mine (Orphan Boy) as a heat source for a 240- kW closed-loop heat pump with the goal of heating a 2,000-m2 building. The mine has a 245-m vertical shaft connected to a large stope by three horizontal cross-cut shafts. There is 1,250 x 106 L of water at a consistent temperature of 24-26° C that is available mostly in the stope. The only heat exchanger placement option is in the vertical shaft. Therefore, the focus was to model heat exchanger placement in the vertical shaft to determine the extent to which the systems will induce thermal currents between the stope and vertical shaft. Modeling of thermal currents, temperature profiles and heat contribution from the ground was done using finite difference and computational fluid dynamics. An optimal configuration was determined showing sufficient water movement and heat transfer will occur with a low water temperature in the shaft above 20° C. This project supports a U.S. Department of Energy (DOE) grant that will implement the full-scale system.

Jan 1, 2013

By Rodrigo Jerez

Advances in inexpensive computer automation led to the development and use of a computerized ore control system at the Cyprus Copperstone Gold Mine near Parker, AZ. These new ore control practices improved accuracy, performance and productivity of the ore control effort. An automated system for data collection, including bar coding of blasthole samples, laboratory analysis, data management, grade estimation, cut delineation and ore zone stake out, plays a major role in ore control practices. This is of particular interest because of the large amount of blasthole information being processed, analyzed and reported daily. Copperstone Gold management has been progressive toward new, efficient methods regarding ore reserve estimation, long-term mine planning, short-term mine planning, ore control and surveying. Technological advances, including powerful personal computers, applicable mine planning software and surveying instrumentation, have become readily available and affordable. The computerized ore control procedures used at Copperstone include sample data collection, laboratory automation and computerized data management. These have reduced the time to complete ore control on a blast pattern by 50% to 75%. The final product - ore control - is generated in a more timely and accurate manner.

Jan 1, 1991