Search Documents

By I Brum

Brazil and Colombia have large reserves of coal, those reserves in Brazil are located predominantly in the south and Colombia the main reserves are located in the north. Despite the relative ease of exploitation, these resources have been underestimated as a source of energy. Currently, these countries are developing projects and partnerships aiming to qualify this mineral resource, adding quality to the final product of the processing plants. In this scenario the processing of Brazilian and Colombian coal in flotation columns appears as a promising alternative, having been successful in mineral systems containing fine particles This paper aims to study the overall process of column flotation for a specific Brazilian coal and a specific Colombian coal. The material used in this study consists of fine coal from Brazil (Copelmi) and Colombia (Cerrejon). The objective is to recover carbonaceous matter and reduce the ash and contaminants grade. The two coals were floated using a negative bias in a 5 cm diameter conventional flotation column of 5 m high. Flotation parameter investigated included air velocity in the range 0.6 to 1.5 cm/s. For all runs, a constant negative bias of -0.25 cm/s and a pulp concentration of 8% w/w were used. For Cerrejón coal, 300 g/ton of frother and 907 g/ton of collector was used, whereas for Copelmi coal, 600 g/ton of frother and 1815 g/ton of collector was employed. The frother was a commercial Aerofroth 65 (AF65), whereas the collector was Kerosene. For the Colombian coal, in general, yield, organic recovery, ash recovery and water recovery decreased with the increasing air rate. However, for Brazilian coal the air rate had no significant effect. For Colombian coal, the highest yield (60% w/w) and organic recovery (69% w/w) were obtained at the lowest air rate (0,6 cm/s). Keywords: negative bias, column flotation, coal

Sep 1, 2012

By S. M. Bradshaw, V. Rocher, L Kabondo, B. Combrink, C. A. Snyders

Media losses are a significant contributor to the operational cost in a dense media separation (DMS) circuit. Of these losses, up to 80 wt% can occur on the drain and rinse vibrating screens. Although these screens are an integral part of any DMS circuit, surprisingly little work can be found in open literature regarding the effect of aperture configuration on the drain rates (draining water and medium). To establish the effect of slot aperture size, experiments were conducted on a 0.6 x 1.2 m vibrating screen with polyurethane (PU) panels at slurry densities between 1.6 – 2.8 kg/L, and volumetric flow rates of 19 – 25 m3/h for both ferrosilicon and magnetite. Results showed that an increase in the volumetric flow rate led to an increase in drainage rate, moisture content and medium carryover. Once an optimum volumetric flow rate was exceeded, a further increase in flow rate resulted in a decrease in drainage rate with a sharp increase in moisture and medium bypass to the oversize stream. An increase in ferrosilicon slurry density led to a decrease in drainage rate with an increase in moisture and medium bypass with each of these rates increasing as the slurry density increased. For magnetite, a gradual decrease in drainage rate was observed with increase in slurry density and volumetric flowrate beyond the screen optimum point. It was found that an increase in aperture size from 0.63 x 8.8 mm to 0.8 x 8.8 mm to 1.0 x 13 mm resulted in an increase in ferrosilicon drainage rate of between 1.3 - 1.8 m3/m2/h depending on the flow rate and slurry density with a reduction in moisture and medium carryover of between 1.0 – 1.2 % and 14.1 – 20.2 kg/t/m respectively. For magnetite, the drainage rate increased between 1.0 - 1.4 m3/m2/h as the slot width increased from 0.63 x 8.8 mm to 0.8 x 8.8 mm while an increase in slot length from 0.63 x 8.8 to 0.63 x 12 mm only resulted in an increase in drainage rate of 0.1 - 0.5 m3/m2/h.

Jan 1, 2018

By M. Taheri

Multiple Attribute Decision Making (MADM) method is applied to select tailings site of the Gol-e-Gohar Iron Ore Processing Plant in the Kerman province, south-eastern of Iran. To select tailings site, screening is applied on eight location proposed by Binnie and Granges. Consequently three sites identified for further studies. Evaluation factors include only the most important factors such as efficiency ratio, elevation and distance to processing facilities, occurrence of faults and fractures. Crisp values such as efficiency ratio, elevation and distance can be determined by measurements and calculations, but some factors such as occurrence of faults and fractures are presented as linguistic values that can be described with triangular fuzzy numbers. Based on evaluation values obtained an optimal tailings site can be selected using a modified Technique of ranking Preferences by Similarity to the Ideal Solution (TOPSIS) given crisp data and linguistic variables as the alternatives of attributes. Each attribute?s weight is assigned using the analytic hierarchy process. The final ranking order aids in the selection of tailings site. Finally, the stages of modified TOPSIS method were applied and site No.2 situated in 5400m to the mill was selected as the best alternative.

Jan 1, 2014

By F. Karakas

In this investigation, one of the most energy consuming stage of the cement manufacturing process, grinding stage, was studied. The aim of the study is to reduce the energy consumption. Optimum operating parameters were determined. Experimental studies were performed at three differ-ent stages. Grinding of limestone, clay and marl which are the main components of the cement, to approximately below 90 microns, was the first stage of the cement grinding. At this stage, effect of feed size and ball charge were investigated. At the second stage, the Bond work index of clinker and additives (slag, trass, limestone and gypsum) was found separately. After forming composite cement with clinker and additives, the Bond work index of this mixture was also determined, thus the results of separate grinding and grinding of mixture were compared. The Bond work index of mixture was found as 13.59 kWh/t, while the arithmetic mean of the Bond work index values of components was 14.90 kWh/t. Finally, clinker and additives (slag, trass, limestone and gypsum) were ground under the same conditions. At this stage, laboratory type of ball mill was used in order to understand grinding characteristics of the cement components. As a result of the experiments, it was found that energy consumption for the grinding will be lowered if the mills with 38 % ~ 40 % ball charge are used in the cement grinding. Moreover, grinding with mixture of clinker and additives gave better results than separate grinding of these components in terms of energy consumption.

Jan 1, 2014

By Xiaojing Li, Yueyuan Zhou, Shengyao Ma

The paper presented the acnalysis of field intensity of rare-earth permanent magnet with high BH product and the research of magnet configuration with narrow pole pitch on open magnet surface, both using ANSYS. The possibility to separate micro-disseminated feebly magnetic minerals by improving the field intensity and the capture line distribution rate on open magnet surface were verified. The research on the method to pile up magnets to increase peak value of field intensity on the open magnet to 1.0T was done through correlation analysis between shape and dimensions of magnetic material and field intensity. And the research on technology method to improve capture line distribution rate in the separating field to 1.25×105/m2 was done through optimization design of magnet configuration of the open magnet with narrow pole pitch. Laboratory tests were performed with hematite sample from ore dressing plant such as Hainan mine, Qidong iron ore, etc. The separation results acquired were at the same level as using the electromagnetic separator, verifying the possibility to separate micro-disseminated feebly magnetic minerals with open magnet. The research suggested a new idea about the development of magnetic separator with high efficiency and low costs to separate feebly magnetic minerals and non-magnetic gangues.

Jan 1, 2014

By M. J. Lottering

Gold deposits in South Africa are invariably associated with uranium bearing minerals. Although it is low grade uranium by international standards, averaging around 0.3 kg U3O8 per ton of ore, recovery of uranium as a by-product improves the overall economics of gold extraction. Moreover, the current high uranium prices as well as increased demand due to renewed interest in nuclear power provide significant incentives for dedicated uranium production. An understanding of the uranium leaching response to changes in operating conditions is an important first step to-wards optimisation of uranium recoveries. In South African acid leaching plants, uranium dissolutions higher than 90% are difficult to achieve, and the chemical origin of this limit is not clear. To study leaching behaviour, an important consideration is the mineralogical characteristics of the ores. Typically, a diagnostic leaching approach can be followed. In this paper, a mineralogy-leachability explanation is presented to rationalise the difficulty in exceeding 90% dissolution from low grade uranium ores on the basis of a simple diagnostic leaching method. It was found that brannerite was the main reason for the existence of a dissolution limit in Witwatersrand ore and that chemical liberation was more effective to increase end dissolution compared to physical liberation. The findings from these investigations will form guidelines for developing economically viable flow sheets for improved uranium recovery, at least in a South African (Witwatersrand) context.

Jan 1, 2014

By P. Fecko

The objective of the paper was application of bacterial leaching on two brown coal samples from locality Mine Druzba, seams Antonin and Josef (Sokolov brown coal basin, Czech republic). Based on the results of bacterial leaching and petrologic analyses of the given samples, it is possible to say that application of bacterial leaching gived good results. Applying bacterial leaching it is possible to remove from 34% to 47% of total sulphur and from 45% to 64% of pyritic sulphur from the coal.

Jan 1, 2014

By A. A. Lavrinenko, N. I. Gluhova, L. M. Sarkisova, D. V. Makarov

"The purpose of the study is to study the feasibility of using sodium diisobutyl dithiophosphinate (DDP) to enhance the recovery of platinum group elements from low-grade refractory copper-nickel ores characterized by a portion of nickel and platinum group elements (PGEs) locked in the dominant sulfide mineral — pyrrhotite. These ore characteristics dictate the need to produce a bulk PGE-containing sulfide concentrate due to the difficulties of producing selective concentrates without a significant loss of the metals.New data on the adsorption and flotation performance of DDP-containing collectors were obtained by measuring the electrode potential, hydrophobicity of the sulfide mineral surfaces and by means of extraction spectrophotometry and flotation studies. The interaction between DDP, pyrrhotite, and pentlandite leads to the formation of surface hydrophobic layers consisting mainly of disulfide and a small amount of metal compounds. These adsorption layers are formed by the reaction with butyl xanthate. In the case of cooperite, DDP reacts with the surface, forming not only disulfide, as in the case of butyl xanthate, but also a complex platinum compound. DDP-containing agents demonstrate stronger collecting properties with respect to sulfide minerals of copper-nickel ores compared to butyl xanthate, which is explained by a stronger hydrophobizing effect and foaming properties.The addition of a combination of DDP-containing agents and butyl xanthate at a ratio of 3:1 for the recovery of sulfides and PGEs in the bulk flotation of copper-nickel ore made it possible to improve the recovery of Ni, Pt, and Pd by 13.6, 9.2, and 9.4%, respectively, relative to the recovery achieved in flotation with butyl xanthate.Bulk flotation with the addition of a composition of DDP-containing agents and butyl xanthate allows the most complete recovery of all valuable elements and is the only technologically feasible method for processing of lowgrade ores, when it is impossible to produce without loss high-grade selective concentrates suitable for smelting."

Jan 1, 2018

By John Starkey

"The development of the Minnovex SAG Power Index (SPI) Test in Canada has created a new and accurate way to measure ore hardness in a SAG environment. Coupled with the standard Bond Ball Mill Work Index Test it is now possible to determine from these two relatively inexpensive laboratory tests, the amount of energy required to grind an ore from the primary crushed size to the desired liberation size. By testing multiple samples to discover where the hard and soft ore zones are located, the representative hardness distribution for the ore body can be determined and grinding equipment selected that is capable to meet production targets for all mining areas of the deposit.In the last century, it was deemed prudent to select up to 50-tonne samples of ore for Semi Autogenous Grinding (SAG) pilot plant tests and a second 5-tonne sample for metallurgical pilot plant work. The methods outlined in this paper show how the 50-tonne sample is no longer required for SAG design because it is better to measure the representative hardness distribution of the ore body than the hardness of a “chosen” representative sample. This is demonstrated to be true by the fact that the lower horizons of an ore zone cannot initially be accessed to recover 150mm pieces, and the bulk samples taken, rarely represent the desired design hardness of the ore. Median hardness will not yield a good result in most cases and a clear understanding of the location and extent of the hardest zones is imperative to achieve a truly successful grinding circuit design.This paper discusses two plants (Kubaka and Agnico Eagle) that have been designed using SPI and Bond with no pilot plant test backup. Both have been very successful in that they can grind design tonnage on the hardest ores in the mine. This guarantees that the mine’s profitability is protected in any mining sequence. It also allows the extra power to be converted to higher throughput on softer ores if additional cash flow is needed. The advantages from the owner’s point of view are dramatic. This procedure will be attractive as well when considering the costs for test work, and the samples for testing. Existing diamond drill core is normally used and this allows the inclusion of data from the deepest regions of the mine. In addition, it is also clear that the decision to use a crusher can now be made at the design stage of a project based on measured parameters and the estimated capital costs of alternative designs."

Jan 1, 2003

By Y. C. Liu

Arsenic bearing copper-gold ores deposit have been found in most areas of China, especially in southwest. Due to the very closed association between arsenic, copper and gold, conventional flotation and cyanide leaching process may not give positive results. An arsenic bearing copper-gold ore in Sichuan province ,with gold grade of 10.12 g/t, 0.6% Cu and 0.14% As, is characterized by superfine grains with -40 microns fraction accounting for 70.9% and the gold enwrapped mainly by pyrite and tennanite accounts for 34.31%. Arsenic in this ore occurs in isomorphism, deposited in tetrahedrite. The ore was processed primarily in two stage flotation to get copper bearing gold concentrate and pyrite bearing gold concentrate respectively, and sequentially processed by leaching. Under the pressure of 300 KPa and 110~115 ?, the copper-gold concentrate was leached by an oxidizing and catalyzing leach agent then copper and gold were separated from each other in leach solution. The pyrite bearing gold concentrate was processed by cyanide leaching with the leach residue as sulfur product. The test results showed that copper recovery was up to 88.89%, gold recovery up to 89.18% and sulfur recovery up to 92.64%.

Jan 1, 2014

By Jyotirmoy Sarma

The surface-active agent, like sodium humate, in the present systems produces a very stable suspension. Saline water up to 15% is used as a flocculating agent for recovery of water from the dispersed phase containing 1% solid. The recovered water in the presence of humate at different concentrations (0.05-0.2%) and at pH 8 also produces a stable dispersed phase of iron ore fines and tailings. The beneficiation techniques adopted in the present systems can increase ~ 2-3% iron value in the concentrate of iron ore fine, however, for tailings the increase in iron value is not observed. Keywords: beneficiation, flocculation, iron ore fines, tailings, saline water, surface-active agent

Sep 1, 2012

By Fangming Liu

The key problems of current flowsheets and equipments are analyzed. A new steel slag's crushing flowsheet whose key equipments are the improved inertia cone crusher and inertia vibrating jaw crusher is proposed. An advanced two stage open-circuit crushing method is adopted in the flowsheet, with 90% of particle size crushing under 6mm. Using inertia vibrating technology and selective crushing principle the crushers can realize steel slag separating fully into steel and slag and with flexible transmission mechanism the crusher can be protected when iron lump is passing. The flowsheets can enhance the recovery of metal greatly, and expand the application range of tail slag and added value.

Sep 1, 2012

By Bo Feng

The development of surface charge of serpentine mineral and implications for sulphide ?otation have been studied through flotation tests, sedimentation tests, zeta potential measurements and optical microscope photos. The results show that the serpentine mineral was positively charged at an extensive pH range, with an isoelectric point (IEP) of 11.9. The magnitude and sign of the pyrite particles were pH dependent and were negative for pH values above 2. At pH value 9, where ?otation of nickel sul?de ores is routinely performed, serpentine and pyrite particles attract through an electrostatic mechanism. Slime coatings of serpentine adhere to the surface of pyrite, reducing pyrite flotation recovery. The removal of magnesium ions from the serpentine surface by acid leaching results in a decrease of serpentine IEP and eliminates the adverse effect of serpentine on pyrite flotation. Therefore, it has been clearly established that the surface charge value developed in the serpentine/aqueous electrical interface is a function of the serpentine surface incongruently dissolution. As a result of hydroxyl dissolution, the magnesium ions are left in serpentine surface, which is responsible for serpentine surface charge. The methods, which can remove magnesium ions from serpentine surface, can be used to eliminate the adverse effect of serpentine on pyrite flotation.

Sep 1, 2012

By W. Z. Yin

It is investigated systemically in this paper that the granularity of the precursor, ZnC2O4?2H2O, is influenced by synthetic conditions. Instantaneously adding of precipitation agent is able to control the mean size of precursor ZnC2O4?2H2O under 300nm, which has great function to obtain well-dispersed ZnO nanoparticles in the next step, pyrolysis. The pyrolysis kinetics model of ZnC2O4?2H2O powder is obtained. Two steps take place during the pyrolysis. The first is dehydration, which the pyrolysis kinetic model is 2(1-a)2/3(chemical reaction), A=8.3×108s-1, E=(75.82±3.00) KJ/mol. The second is formation of ZnO, which the pyrolysis kinetic model is (1-a) (random nucleation and latter growth), A=8.45×1028s-1, E=(360.54±12.00)KJ/mol. ZnO nanoparticles obtained by pyrolysis take on self-growth behavior. It is resulted that for precursor ZnC2O4?2H2O pyrolysis time takes obvious influence on the partilces size under 420?, 500? and 600?. Finally, a new flow sheet for synthesis of ZnO nanoparticles is investigated, in which blendes is used as raw material and hydrometallurgy is introduced into it. The whole flow sheet has no industrial wastes, that is all byproducts can be used in the flow sheet recycled, resulted in the de-crease of productive cost and industrial wastes.

Jan 1, 2014

By A. Zangooi

Frothers play major roles in flotation through interaction at the air/water interface. A method of determining frother adsorption density (coverage), i.e., the number of molecules per unit of interfacial area of bubble surface, is introduced. The technique is based on mass balancing the frother around a continuously operated bubble column. The mass balance requires collection of bubbles before they burst. The column design and operating procedure is reviewed, and some preliminary results discussed. Keywords: flotation, colorimetric frother analysis technique, frother mass balance, coverage

Sep 1, 2012

By S. J. Lui

Sodium oleate was an effective diaspore collector, whereas chelate collector OL2 showed certain collecting power over diaspore and nonionic surfactant OL3 showed little collecting ability. Then experiments were carried out using sodium oleate as the main collector with the addition of OL2,OL3 to study the influences on diaspore flotation, it could be seen from the experiments that accelerants had a marked influence on the recovery of diaspore, which could be raised by 10%, and the addition sequence also affected the flotation behavior: the best results could be gained when the accelerants were mixed thoroughly before adding and the best ratio of collector OL1 and accelerant OL2, OL3 stood at 30:2:1. Based on the calculation of the ingredients in the sodium oleate solution, sodium oleate reacted with surface of the mineral and formed the acid-soap polymer [HOl?Ol-] when pH was about 9. Zeta potential test showed the accelerant promoted the absorption of collector on the mineral surface, which lowered zeta potential. As could be seen from surface tension experi-ments, the addition of accelerant OL3 lowered the CMC value of OL1 solution, which was equiva-lent to raise the power of the agents. Further Infrared Ray experiments showed the co-absorption of OL1 and OL2 make aluminum oleate on the mineral surface more stable. Up till now, the mixed reagents with sodium oleate as the main collector, combined with other two accelerants had been used in the Zhongzhou concentration plant, which is the first diaspore flotation plant in China.

Jan 1, 2014

By Shounak Banerjee, Suresh Babu Dasari, Dharmendr Kumar, Shashank Pardhikar, Beena Rai, Venugopal Tammishetti

Recent increase in steel demand has led to the increased usage of high grade iron ores. During the mining, crushing and washing of ore, huge quantities of fines and slimes (<150 µm) are generated, majority of which is dumped into tailing ponds owing to their high alumina contents (~10-15%). Due to rapid depletion of high grade iron ore, it is the need of the hour to utilize low grade iron ore fines and slimes. These fines and slimes contain high iron values assaying 45-60% Fe. Dumping these valuable resources in ponds locks enormous land space and causes environmental hazards. The constituent minerals present in Indian iron ores comprise of hematite, goethite, gibbsite, kaolinite and quartz. Our research is focused on beneficiation of iron ore slimes through selective flocculation. We use density functional theory simulations to screen the reagents and perform experiments with screened reagents to determine the experimental conditions for effective performance of the reagents. Our studies revealed that reagents like starch, guar gum and carboxymethyl cellulose exhibit excellent selectivity in high alkaline pH range. However, the higher cost of alkali makes the process economically less attractive. In the present study, a commercial reagent from NALCO Water (Hi-Tex 83570) has been explored as selective flocculant for beneficiation of iron ore slimes in wide pH range (4-11). However, the reagent was also found to be the most selective in alkaline pH range only. Full factorial design of experiments was done considering three parameters namely, pulp density, flocculant dosage and settling time. Regression models were developed for yield, iron grade, alumina grade and iron recovery in the concentrate, using experimental results. Further parameter optimization was done to achieve high Fe recoveries and low alumina recoveries. The optimal parameters thus arrived at were validated with the experiments. We were able to achieve a concentrate grade of 60.0% Fe and 5.1% Al2O3 with 68.8% Fe recovery from a feed containing of 53.1% Fe and 8.9% Al2O3. The performance of flocculant Hi-Tex 83570 was also compared with reagents starch and guar gum.

Jan 1, 2018

By Jim Pae Lem

This study investigates the mode of occurrence of uranium in a copper concentrate from the Prominent Hill mine. Mineralogical and liberation studies of a high grade Cu concentrate (monthly composite) containing uranium (U) were undertaken using QEM-Scan in combination with QXRD and ICP-MS. The study aimed at determining in what form U was recovered, and by which mechanisms. The deportment of U was studied in 3 size fractions; +20µm, -20+8µm and -8µm. QEM-Scan analysis showed that uranium was present as U(Cu)-silicates, U-silicates, UPbOx/FeOx or traces of UThOx and UTiOx, with the U-silicates present across the size fractions. The association of uranium bearing minerals with copper sulphides varied across the size ranges. Interestingly, most of the U (46% by weight) was distributed in the finest fraction (-8µm), in which the deportment of Cu was low (6%). Over 40% of the U mineralisation in the -8µm was liberated. In terms of the floatation response, while recovery of the uranium minerals as a result of their association with copper sulphides (as composite particles) was evident, recovery of UPbOx locked in hydrophilic haematite in the +20µm size fraction suggests, that other mechanisms (e.g. Inadvertent activation by Pb from radioactive U decay) are possible. Furthermore, the high amount of fine liberated U bearing particles in the concentrate points at entrainment as another major mechanism for uranium recovery, and therefore, a target for process optimisation.

Sep 1, 2012

By S. L. Zheng

The compound material of Nano-TiO2 Supported on the diatomite was prepared by the hydrolytic method with purified diatomite and TiCl4. The compound material was characterized by SEM, XRD, TEM, EDX, XPS, and the application test of the compound material was studied. The characterization test results showed that the Nano-TiO2 was coated on the surface of diatomite, the crystal of TiO2 is anatase, and the average crystal size is 12 nm. The pore diameter was reduced, but pore volume and surface area of the compound material are increased after Nano-TiO2 Supported on the diatomite. The application test results for treating coking waste water and formaldehyde gas show that the compound material of Nano-TiO2 / diatomite has adsorption and photo-catalytic function and strong degradation performance for phenol and formaldehyde.

Jan 1, 2014

By M. M. Kulkarni1

Kaolin clay is used as a filler and pigment in various applications such as paper, paint, rubber, plastics, adhesives, ink and ceramics etc. Major mineral content in crude kaolin clay is kaolinite along with some accessory minerals as quartz, hematite, mica, feldspar, anatase, rutile, illemnite etc. The Fe and Ti bearing minerals play very important role in determining quality of the kaolin, as these minerals impart yellow, pink or darker color to the white kaolin. Conventional beneficiation methods used in kaolin processing are de-gritting, classification and sodium dithionite bleaching, which improves the optical properties of kaolin, wherein reduction of color imparting constituents such as Fe2O3 and TiO2 is marginal. In the present study, these coloring impurities are separated using selective adsorption of water-soluble polymers. Degritted kaolin samples after passing through 45 micron sieve is used in the study for selective flocculation by polyacrylamide based polymers. The effect of pH, zeta potential, and polymer dose on the reduction of impurities is studied. Analytical tools such as XRF, XRD, SEM, and TEM techniques are utilized and results are discussed in detail.

Sep 1, 2012