Search Documents

By J. H. Swisher

An experimental study has been made of the possible mechanisms for foam stability in the system CaO-SiO2-Cr2O3, where Cr2O3is the foaming agent. The degree of lowering of surface tension by Cr2O3 was determined at 1600 "C for high -silica melts. Measurements were also made of foam stability under standardized conditions. The results of the two sets of measurements then were correlated by applying the Gibbs and Marangoni theories of film elasticity. It was demonstrated that the Marangoni elasticity effect is probably the largest single contributor to foam stability, although the high uiscosity of' silicate melts makes some contribution in controlling the rate of drainage of liquid from bubble lamellae. ThE tendency of metallurgical slags to foam has frequently been observed during steel-refining operations. In the open-hearth furnace,this tendency is considered undesirable because it slows down the rate of heat transfer from the burners to the molten-metal bath. On the other hand, it is sometimes desirable to have a "foamy" slag in the basic oxygen converter.' A more effective blanket over the steel bath is made by a "foamy" slag, and loss in yield of metal due to splashing is minimized. In addition, a flush slag can be removed more easily in this condition. Since slag-foaming problems in the field have been attacked largely on an empirical basis, it appeared desirable to obtain a better basic understanding of the mechanism of foam stability. The experimental work was directed almost entirely toward the behavior of Cr2O3 as the foaming agent in CaO-SiO,-Cr2O3 melts. In the first stage of the investigation, the degree of lowering of surface tension by Cr2O3 was determined at 1600°C. The second stage consisted of measuring foam stabilities under standardized conditions. The two sets of experimental results then were correlated by applying various theories of foam stability. For convenience in interpreting the surface-tension and foam-stability results reported here, a portion of the CaO-SiO2-Cr2O3 phase diagram2 is reproduced in Fig. 1. EXPERIMENTAL 1) Surface-Tension Measurements. Very little information is available in the literature on the lowering of surface tension of slags by foaming agents. Kozakevitch 3 mentioned that the addition of 1.5 pct Cr2O3 lowered the surface tension of FeO slightly. In another system, some data on the lowering of surface tension of foaming slags by P2O5 were reported by Cooper and Kitchener.4 The technique used for the surface-tension measurements was the maximum bubble-pressure method,' using a single tube immersed to various depths in the melt. This method has been used extensively in high-temperature systems, such as in liquid metals, slags, and glasses.6,7 It has the advantage that the contact angle between the liquid and the tube material need not be known. The equation used for calculating surface-tension values from maximum bubble-pressure measurements is the Schroedinger equatioq5 which can be written as follows:

Jan 1, 1964

By Arnulf Muan, Egil Aukrust

Activities of COO in the three solid solution series COO-MgO, COO-MnO, and COO-"FeO" have been determined at 1200°C by equilibrating oxide samples with a metal phase (cobalt or a Co-Fe alloy) in atmospheres of known oxygen activities. The systems COO-MgO and COO-MnO are ideal, within limits of experimental error, whereas the system COO-"FeO" shows a slight positive deviation from ideality at the temperature of this investigation. KNOWLEDGE of activities of oxide components in solid solutions is necessary for the calculation of the cation distribution among coexisting oxide phases in many important metallurgical, ceramic, and geochemical systems. Very few activity-composition curves are available for such systems at the present time. A start on the prodigious job of obtaining such data has been made by studies of solid solutions with simple sodium chloride type structure containing NiO or "FeO" as a component.1-3 The present paper describes similar studies for solid solutions with sodium chloride type structure containing COO as a component. For the systems COO-MgO and COO-MnO, the activity solid solution is determined by the equation Here po and are the oxygen activities of the gas phase in equilibrium with the phase assemblages metallic cobalt plus oxide solid solution, and metallic cobalt plus pure COO, respectively. In the system CoO-"Fe07', the metal phase is a Co-Fe alloy rather than pure cobalt. In this case the activity of COO in the oxide solid solution is calculated from the equation where a& is the activity of cobalt in the metal phase. Because the system Co-Fe is close to ideal4 and the metal phase appearing in the present work contains less iron than cobalt even at the lowest COO concentrations of the oxide phases used may be set equal to N . Hence, Eq. [2] becomes The value of Nc, can be estimated from the relative stabilities of the oxides COO (see below) and I) EXPERIMENTAL METHOD Two different but closely related procedures were used in the present investigation to determine the activity-composition curves. In one method, the oxide solid solutions were equilibrated against

Jan 1, 1963

By Phillip E. Deering, Robert M. Cox

A model pillar study was conducted in which the engineering principles of dimensional analysis were applied to the problem of coal mine pillar design. The paper reviews the theory of similitude as applied to the model pillar study conducted in the investigation. An example solution of a design problem is included to indicate how the results of the study may be used as a first approximation in the design of coal mine pillars. The design of mine pillars for adequate support with minimum loss of valuable raw materials has always presented a problem to the mining engineer. Most often, for lack of a better method, past practice has influenced the design of new mine pillars. This process has always left doubt as to the safety factor of the pillars. The work presented in this paper is an initial attempt toward adapting the engineering principles of dimensional analysis to the problem of pillar design in underground mines. The use of the dimensional analysis technique is advantageous because all the variables associated with the problem are considered, and by systematic analysis the relative influence of each variable is determined. The model material utilized in this study was taken from the Helena seam of the Cahaba coal field located in central Alabama. The research study was sponsored by The Southern Electric Generating Co. as part of an over-all rock mechanics investigation of the Helena seam area. THEORY OF SIMILITUDE Model analysis is used extensively in engineering today, particularly in the solution of design problems that defy the classical methods of analysis. Such problems arise when materials with a nonlinear stress-strain relationship are involved, when geo- metric boundaries are difficult to define in simple form, when strains become large, or when partial failure occurs. All of these difficulties usually exist in pillar design problems. Those principles which underlie proper design and construction of models, and the interpretation of test results, comprise the theory of similitude. That is, the theory of similitude includes a consideration of the conditions under which the behavior of two separate entities or systems will be similar, and the techniques of accurately predicting behavior of one from observation of the other. The theory of similitude may be developed by dimensional analysis. Dimensional analysis, as a powerful analytical tool, is developed from a consideration of the dimensions in which each of the important quantities involved in a phenomenon is expressed. It is based on two axioms: 1) Absolute numerical equality of quantities may exist only when the quantities are similar qualitatively. 2) The ratio of the magnitudes of two like quantities are dependent on the units used in their measurement, provided that the same units are used for evaluating each. Dimensional analysis, developed from these two axioms, differs from other types of analysis in that it is based solely on the relationships that must exist among the pertinent variables because of their dimensions, rather than on the relationship of natural laws. In itself, dimensional analysis ~rovides qualitative, rather than quantitative relationships, but when it is combined with experimental procedures, it may be made to supply quantitative results and accurate prediction equations. APPLICATION OF THEORY The design of an adequate mine pillar requires the determination of a design equation and the selection of a dimensional system with which to work. Since force plays an important part in the design of mine support, the FLT (force, length, time) system has been used. The factors involved in the dimensional analysis of mine pillars and their dimensions are: A = cross-sectional area L Cp = design strength FL- E, = tangent modulus of elasticity FL

Jan 1, 1969

By C. E. Melbye

A serious problem confronted the city of Gunnison early in 1958 in that, for a few months during each spring runoff, the water supply derived from the Gunnison River became polluted to an unsafe point. The city management had the choice of building a new filter plant to replace the old unworkable one or drilling wells to develop a ground water supply. The cost of a new filter plant was estimated at $180,000 compared to $50,000 for 6 wells, pumps, and additional water lines, hence their decision to attempt the development of sufficient ground water. Six wells at 300 gpm per well were estimated as necessary to handle the peak usage of 1800 gpm, compared to only 600 gpm winter usage. Although the water table is only about 7 feet below the surface, existing private wells drilled at random locations were producing much less than 300 gpm. The problem was to find sufficient quantities from about 6 wells. Since the presence of an ancient bedrock channel was suspected, which would be expected to localize greater quantities of water, the city of Gunnison authorized a resistivity survey to investigate bedrock topography below unconsolidated gravels. Survey results were highly satisfactory and led to the preparation of a fairly detailed bedrock contour map, Fig. 1. This map was used in selection of all well sites. The city of Gunnison is situated in a flat, broad, Quaternary gravel-filled valley (terrain dips south at 20 feet per mile) at the junction of the Gunnison River and Tomichi Creek. The valley, about 2-4 miles wide, is bordered by hills of Tertiary volcanics to the northwest, Cretaceous and Jurassic sediments to the north and northeast, and pre-Cambrian granite and gneiss to the south. One previous deep test well at the west end of the city hit pre-Cambrian granite at 496 feet, which, allowing for 40 feet of surface gravels, makes the older sedimentary section 456 feet thick. This section is probably all Jurassic Morrison formation, consisting of the Saltwash sandstone overlain by the much thicker section of Brushy Basin shales and mudstones. According to the driller's logs, each well was bottomed in what is believed to be Brushy Basin shale. FIELD PROCEDURE A standard Gish-Rooney type of resistivity apparatus was employed, which used 45-volt dry batteries as a direct-current power source. Applied voltages could be selected from 45 volts to a 270-volt maximum. Copper-coated steel stakes were employed as current electrodes and porous porcelain pots as potential electrodes to avoid possible polarization effects with direct current. The expanding Wenner electrode configuration was utilized for this investigation and measurements were made at 20 40, 60, 80, and 100-foot spacings,

Jan 1, 1961

By Gerald Greene

Tan various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulfur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1) states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As.

Jan 1, 1935

By B. E. Warren

Jan 1, 1965

By R. G. Vardiman, M. R. Achter

Observations of dislocation structure in niobium are presented using two techniques. Triangular pits developed by electroetching are confined to orientations in the stereographic triangle between the (111) pole and planes of the (1ll) zone and require the presence of carbon. Some unusual electroetching phenomena at other orientations are noted. A chemical etch of dislocations decorated by the addition of carbon to 50 ppm reveals the complete dislocation line structure in a surface layer up to 30 p deep, with a resolution of less than 1 p. This effect is independent of surface orientation. The structure of subboundary nets may be resolved for misorientations up to about 1'. Dislocation structures found in strain anneal grown crystals, such as helices, prismatic loops, and high-density areas, are observed. The measurement of dislocation density is discussed and values obtained in different ways are compared. IN the course of some work on the response of refractory metals to thermal-mechanical treatments, it was desired to examine the defect structure of relatively low dislocation density crystals of niobium in bulk form. Surface and bulk methods for the observation of dislocations have been reviewed by ~melinckx,' and include etch pitting, decoration, and various X-ray techniques. The dislocation line structure has been developed by decoration in a few metals, although observations were limited to certain orientations, or by the coarseness and nonselectivity of the precipitate. The most commonly used technique is etch pitting. In niobium, etch pits have been developed chemically'0," in material of high impurity content and electrolyti-cally'' in relatively pure material. In this paper, etch pits developed electrolytically, and the dislocation line structure of a surface layer developed by decoration and chemical etching, are examined, and observations are presented from both techniques. EXPERIMENTAL METHODS Our starting material was electron-beam-melted niobium, swaged to 4 or -in.-diam rod. Chemical analysis is given in Table I. Single crystals were grown by a strain anneal technique using 1 to 2.5 pct of strain and growth temperatures of 1700" to 2300"~.'~ Some crystals grown by zone melting were also examined. The desired surface orientation was exposed either by spark machining or by sectioning with a cut-off wheel and prepared for etching by electro-polishing.

Jan 1, 1969

By U. N. Bhrany, N. Arbiter

Over the last one hundred years the problem of assessing the efficiency of energy consumption in producing rock breakage has been studied by many investigators from a variety of viewpoints. Their contributions fall into three main categories: (1) those characterized by a priori assumptions of a relation between the energy required for fracture and the degree of fragmentation produced (e.g. Rittinged(l), Kick(2) Bond(3)); (2) those studying simple systems with controlled energy applications (Gross(4)?(5) ); (3) those treating operating data to develop practical relative measures of efficiency (Coghill(6), Taggart(7)). Closely involved in the efficiency problem is the characterization of size distributions produced by comminution. Unless an experimental size distribution can be approximated by a distribution function and its constants, it becomes difficult if not impossible to develop quantitative energy-particle size relationships. While many such functions have been proposed, none are both completely adequate and convenient. The simpler fonns usually describe only a part of the sizing data, while those which apply to a greater extent are cumbersome(8). The thesis underlying the study here reported can be stated as follows: Size reduction in a tumbling mill subjects ore particles to a relatively constant fracture-producing environment. The intensity of the forces is determined by such factors as the mass of the breaking bodies (rods, balls, rock), and the speed and dimensions of the shell. For a particular ore the extent of size reduction will depend both on the intensity and on the duration of exposure. The latter is the residence time in a batch mill, or is determined by the effective volume and the flow rate in a continuous mill. Size reduction can thus be regarded as a rate process in which the weight of material in size intervals varies as a function of grinding time. Although both the rates of disappearance of coarser sizes and

Jan 1, 1961

By R. Salter, C. K. Chase

Although Asarco's Silver Bell Unit, 40 miles west of Tucson, Ariz., is known primarily for copper production, molybdenite is also produced as a byproduct in the 8000 tpd flotation mill. The Silver Bell ore comes from two pits approximately two miles apart. Copper mineralization is essentially chalcocite resulting from two to three-fold secondary enrichment in a highly altered zone. A typical porphyry copper deposit, Silver Bell ore is of medium hardness. The ore consists of about one part molybdenum to 65 parts of copper. In the copper concentrate which is the starting point for separate molybdenum recovery, the ratio is also one part molybdenum to 65 of copper. Molybdenum mineralization is primary. Enrichment is not evident but it is notable that the molybdenite is more common in the more siliceous, harder rocks. The actual molybdenite occurs as diversely oriented flakes of fairly constant grain size, mostly in fractures associated with quartz veins. Most of the mineral appears unoxidized; secondary coatings on the molybdenite flakes are fortunately rare. In May 1962 a modified, improved version of the molybdenite circuit was put into operation.

Jan 7, 1964

[Separates of all the Technical Publications published in 1928 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found either in the TRANSACTIONS or in the special volumes issued by the Institute] . METAL MINING TECHNICAL TRANS. PUBLI- TITLE AUTHOR MEETING VOLUME CATION AND PAGE* No. 50 .The Eötvös Torsion Balance D. C. Barton New York Method of Mapping Geologic Feb., 1928 Structure 52 A Cartographic Correction for the C. A. Heiland New York Eötvös Torsion Balance Feb., 1928 61. Liquid-oxygen Blasting at Chuqui- H. C. Schultz, New York camata, Chile F. K. Middleton Hunter Feb., 1928 76, 108, 123 64 Working Methods of Practical Geo- Hans Haalck New York physics Feb., 1928 65 Experiments with Eötvös Torsion P. W. George New York Balance in the Tri-State Zinc and Feb., 1928 Lead District 74 Gravity Surveying in Great Britain H. Shaw New York Feb., 1928 75 The Computation of Eötvös Gravity E. Lancaster-Jones New York Effects Feb., 1928 82 Earth-resistivity Measurements in W. 0. Hotchkiss, New York the Lake Superior Copper Country W. J. Rooney, Feb., 1928 James Fisher 83 Mining Methods and Records at the Roy W. Moore New York 76, 56, 90 United Eastern Mine Feb., 1928 98 Recent Results in Electrical Pros- Hans Lundberg New York

Jan 1, 1928

By Cleland N. Conwell

Coals are found in all parts of Alaska, ranging in geologic age from Carboniferous to Tertiary, and grading from lignite through anthracite. Only the Matanuska and Nenana coal fields have been extensively developed. Nenana Field Today roughly 94% of the coal mined in Alaska comes from the Nenana field near Healy. The coal-bearing horizons in the Nenana field are found in a sedimentary sequence of Tertiary age approximately 2800 ft in thickness. The sediments rest directly on schists of possible Precambrian age. Individual coal beds in the field have been designated by both letters and numbers, starting with the alphabetical designations from A to G, and the numbers 1 to 6. Of these coals, the principal beds that are mined are F, 1, 2, and 3. These vary greatly in thickness, e.g., bed 1 ranges to over 50 ft, and beds 2 and 3 to 30-40 ft.

Jan 10, 1972

By L. Adler

Longwall caving, one of the most economical and attractive mining methods, is yet one of the most difficult and hazardous.1 This dualism is inherent in a method which manipulates the mine supports themselves to aid in excavation. The difficulty is further compounded by the lack of an analytical method to predict and control results. This paper is intended to meet this need by providing a first approximation to the mechanics involved. The analysis will be limited to materials which are linear-elastic, homogeneous and isotropic. The rock structure is assumed to consist of beds of uniform thickness with no interbed bonding.2 Consequently, the mine roof can be likened to a beam, in which the action characteristic of longwall caving is the controlled deflection of the barrier supports. This deflection causes load to be intentionally transferred from these barrier props to the working face.3 Two of the requirements of this method, shared in common with other mining methods, are the provision of (1) adequate and (2) safe working space. The third requirement is the one characteristic of longwall caving and is somewhat in conflict with the second; (3) the development of near-failure static loads at the face. Requirement (1) is handled by spacing the barrier props sufficiently far from the working face for efficient operation. Requirement (2) limits the static stresses in the structure to predetermined allowable values. This means that it is not desirable to induce a maximum load on the working face as requirement (3) may imply. Such a condition could produce collapse in the whole structure. It is the purpose of the undercut to limit the depth, and thereby control the failure of the face. Therefore, requirement (3) really means the development of an optimum, not maximum, load which, in conjunction with undercutting, produces failure at the working face, with minimum powder consumption. Stress analysis requires an exact delineation of the structure and loads. The structure will be defined as the immediate roof and its supports. Since the roof is severed at the caving line, the supports reduce to the barrier props and the working face, as shown in Fig. 1. The mechanics of failure within the working face itself are complex and beyond the scope of this study, since the face represents a typical mine invert structure.4 However, this lack can be made good by the judicious collection of field data. The primary load on the structure is its own weight or body load which can be considered uniformly distributed over its upper surface. Additional loading occurs due to interference of overbeds with the structure. Wherever this occurs, the effect can be approximated by a load uniformly distributed on the upper surface of the structure.5 When this interference is intermittent, as with a much thicker overbed, the elastic curve for the overbed is superimposed on that for the structure and the extent of interference noted, as Fig. 2 shows. However, for simplicity, this study will ignore such intermittent loads without impairing the generality of approach. Consequently, the free-body diagram is that of a uniformly loaded cantilever beam with an inter-mediate support, as shown in Fig. 3. For convenience of analysis, the diagram will be divided just to the

Jan 1, 1961

By H. D. Outmans

A method has been developed for determining the relative water wet-tability (fraction of the surface wet by water) of porous media. This method involves the adsorption of methylene blue dye from an aqueous solution onto the solid surfaces of rock contacted by the injected dye solution. Experiments on Berea snndstone cores have shown that water-wet cores adsorb a large amount of dye from solution. In oil-wet cores, however, the injected aqueous dye solution is prevented from contacting the adsorptive surfuces by a film of oil and virtually no dye is adsorbed. This method was tested by experiments on mixtures of water-wet and oil-wet sand. Using the dye adsorption method, it was possible to determine quantitatively the fraction of water-wet and oil-wet sarzd in such mixtures. The dye adsorption test is readily applied to determinitrg the relative water wettability of fresh oilfield cores. The cores are not extracted before testing. Observed values of the wettability of field cores tested to date have varied from 100 to 6 per cent water wet. INTR OD UCTIO N Recent articles1 ' have emphasized the important role that wettability plays in almost all phases of reservoir rock behavior. It has been shown that wettability has a profound effect on the interstitial water saturation, residual oil saturation, capillary pressure, relative permeability, waterflood behavior, and resistivity index of oilfield cores. A quantitative investiga- tion of the effect of wettability on these core properties is severely handicapped by the lack of a simple technique for measuring the wettability of a porous medium. If such a technique were available, it would provide investigators with a means of gaining insight into the distribution of phases within a core. A number of qualitative methods of estimating wettability are known. These include contact angle measurements, flotation tests and studies of displacement pressure: imbibition7 and relative permeability data.' Using these tests, it is usually possible to classify a core as water-wet, oil-wet, or some intermediate degree of wettability. One recently proposed method involving measurement of nuclear magnetic relaxatione offers promise of determining quantitatively the fractional wettability of cores. The equipment is rather elaborate and necessary treatment of the cores before testing probably alters the natural wettability. This latter point also applies to most of the cited qualitative methods. This paper presents a new technique for determining water wettability of cores; it is based on measurements of the dye adsorption capacity of the core. This method has the advantage of requiring relatively simple equipment and involves minimum handling of the core before testing. It is important to distinguish between the various concepts of wettability referred to in the literature. The term "wetting" is defined by Bartell as that phenomenon which occurs when a solid and liquid phase come in contact in any manner so as to form a solid-liquid interface. A preferentially water-wet solid is defined by Jennings in terms of the advancing contact angle in the solid water-oil systems. Brown and Fatt regard fractional wettability as the fraction of the total surface area that is preferentially oil-wet or water-wet. However, none of these definitions adequately describes the type wettability measured by the dye test. This calls for the introduction of a new term, "relative water wettability", which we define as the fraction of the total surface area of a core contacted by injected water. DESCRIPTION OF METHOD The ability of a porous medium (especially the clays) to adsorb large quantities of surfactants, dyes, etc., is well known. It is reasonable to assume that a substance can be adsorbed from solution onto a solid surface only if the solution contacts the surface. In this connection Shapiro" has shown by experiments on silica gel that completely dry gel will adsorb methyl red dye from a benzene solution. On the other hand, if a film of water more than several molecules thick is present on the silica gel, the adsorption capacity of the gel for the dye is drastically reduced. Thus, a study of the dye adsorption capacity of cores should give some clue as to the fluid distribution on the surface of the core. TEST OF METHOD As a qualitative check on this theory, dye adsorption tests were run on similar Berea sandstone cores (Table 1, Cores 1-5). Cores saturated initially with water and flooded with 0.01 per cent aqueous methylene blue adsorbed 0.58 mg dye/gm of core. Similar cores saturated initially with water, driven to irreducible water with oil, and then flooded with the same dye solution also adsorbed 0.58 mg dye/gm of core. Another core, treated with a 5 per cent Dri-Film solution, dried and saturated with oil (Soltrol) adsorbed no dye when the dye solution was injected. These tests confirm

By Ivan B. Cutler, Milton E. Wadsworth

Coprecipitation of anionic and cationic polyelectrolytes has been applied to flocculation of several mineral systems. Results obtained in a study of the flocculation of kaolinite and hematite suspensions of polycationic and polyanionic electrolytes are presented. Greatly increased settling rates were observed following precipitation of positive and negative polyelectrolytes on the surface of finely divided minerals in aqueous suspension. The ratios of polycationic to polyanionic electrolytes required to produce maximum sedimentation have been shown to correspond closely with the equivalence points obtained by light scattering studies of systems containing the positive and negative polyelectrolytes by themselves.

Aug 1, 1956

By Ernest M. Spokes

For bituminous and lignite coals the economic picture continued to improve as it has each year since the low of 1961, with production at 480 mil- lion tons in 1964 compared with 1963's 459 million tons. The anthracite industry produced 16.3 million tons in 1964 and 18.3 million tons in 1963. The industry is looking toward a further expansion; among the new developments will be a mining wheel producing 3 million tons of lignite per year in South Dakota. It is expected that electric power generation will continue to provide the market for most of the increase in consumption, with exports second in importance in the expansion. Improvements in methods of mining and transporting coal underground and in strip mines, and the cooperation of carriers in finding ways to reduce transportation costs to distant markets, have made possible these expansions. Research continues to reduce costs of mining, transportation, steam generation of electric power and production of steam for space heating and manufacturing processes, to retain some markets and expand others. Other research seeks to expand markets by developing fuel from coal which will be more attractive than competing fuels, by reducing sulfur and other sources of air pollution. Public relations efforts of the industry are bearing fruit in a greater acceptance of coal as a modern fuel.

Jan 2, 1965

By Charles W. Merrill

Obsolescence in the mineral world is virtually nonexistent if the term is taken to mean that a mineral commodity, once established in commerce and industry, subsequently has fallen into disuse. We are living in an age of minerals. Each generation puts an increasing array of mineral-based commodities, in larger quantities, to more uses than ever before. Bastnasite, a museum mineral and a collector's item a few years ago, is now produced in quantity at Mountain Pass, Calif. Uranium, a minor byproduct of vanadium mining in the Rocky Mountain plateau area before World War 11, has grown to be a leading mineral product in several western States. And finally the total quantity and value of minerals both in the United States and in the World establish new records almost yearly. Surely the mineral industry as a whole is not obsolescent in our economy. Nevertheless, there are particular uses for particular minerals that are obsolescent and some applications have been supplanted entirely. Tin does not occupy the prominent place in foil manufacture that it once did, and the schoolboy's slate left most classrooms before the oldest of us were born.

Jan 9, 1964

By R. E. Ray, J. W. Stevenson, J. A. Berry

Conventional concrete block plastered with a cementitious coating is the most common material used in the construction of permanent stoppings to direct airflow in underground mines in the US. All mines experience various degrees of strata convergence depending on depth of overburden, geological conditions, and type of roof support employed. Strata convergence will cause cracks and joint openings in masonry stoppings, resulting insignificant air leakage losses. Where strata convergence is severe, complete structural failure of the stopping can ultimately occur. Reconstruction of damaged or destroyed stoppings adds expensive overhead to mining operations, and even greater expenses are incurred from the additional fan horsepower required to overcome leakage losses. Ideally, a stopping should maintain high resistance to airflow while yielding to strata convergence. By properly incorporating a polyisocyanurate rigid foam material within the masonry block structure, stopping service life can be increased in mines experiencing strata convergence problems such as floor heave, roof loading, and lateral rib movement.

Jan 1, 1986

By Helmut Thielsch

In recent years an ever increasing amount of interest has been directed toward research studying the principles and various applications of sonic and supersonic waves. Though still in their early stages of practical development, sonic vibrations are already used in the emulsifi-cation and degasification of liquids. Metals exposed to sonic or ultrasonic vibrations while solidifying show a considerable amount of grain refinement. Often sound waves are applied instead of radiography to test engineering materials for internal cracks and flaws.' In the field of pure research these waves are used in dispersion and also in coagulation of particles or liquids in gaseous or, under certain conditions, in other liquid systems. In the settling and thickening of slurries considerable time is necessary to compress the solid particles and to squeeze out the liquid to obtain as low a dilution (liquid to solid ratio) as possible. Various methods have been developed to increase the amount of coagulation of the very fine solids (colloidal or semicolloidal) and to shorten the over-all time. The addition of small amounts of electrolytes and the warming of the suspension represent merely the more important techniques. Some of the effects of supersonic vibrations have been reported previously. From preliminary studies, therefore, it was hoped that by application of sonic vibrations it would be possible to reduce the time required to thicken such materials to a specific dilution, as well as to thicken to lower ultimate dilutions than could be obtained by quiescent settling alone. By increasing the volume thickened per unit time—i.e., improving the plant efficiency— great savings in equipment and time would be obtained for industrial processes. Also, faster settling rates should result if coagulation of particles could be increased. Experiments have been conducted for a period of several months in the Allis-Chalmers laboratory to study the effect of sonic vibrations on settling of particles of different sizes and concentrations. Apparatus The sedimentation apparatus used in these experiments is illustrated in Figs. I and 2. The essential features are the stationary field coil and the movable voice coil. Both windings are placed around a solid iron core. A leather diaphragm connected to the steel frame holds the voice coil in place. A brass rod is fastened to the voice coil with a metal disk connected to the other end. This disk is sealed to the lucite cylinder with a flexible rubber diaphragm. The lucite tube is 17 in. long; its inner diameter is 2½ in. and the wall thickness is ¼ in. The tube is calibrated on the outside in 10 c.c. divisions for a total of 1000 cubic centimeters.

Jan 1, 1947

By Helmut Thielsch

In recent years an ever increasing amount of interest has been directed toward research studying the principles and various applications of sonic and supersonic waves. Though still in their early stages of practical development, sonic vibrations are already used in the emulsifi-cation and degasification of liquids. Metals exposed to sonic or ultrasonic vibrations while solidifying show a considerable amount of grain refinement. Often sound waves are applied instead of radiography to test engineering materials for internal cracks and flaws.' In the field of pure research these waves are used in dispersion and also in coagulation of particles or liquids in gaseous or, under certain conditions, in other liquid systems. In the settling and thickening of slurries considerable time is necessary to compress the solid particles and to squeeze out the liquid to obtain as low a dilution (liquid to solid ratio) as possible. Various methods have been developed to increase the amount of coagulation of the very fine solids (colloidal or semicolloidal) and to shorten the over-all time. The addition of small amounts of electrolytes and the warming of the suspension represent merely the more important techniques. Some of the effects of supersonic vibrations have been reported previously. From preliminary studies, therefore, it was hoped that by application of sonic vibrations it would be possible to reduce the time required to thicken such materials to a specific dilution, as well as to thicken to lower ultimate dilutions than could be obtained by quiescent settling alone. By increasing the volume thickened per unit time—i.e., improving the plant efficiency— great savings in equipment and time would be obtained for industrial processes. Also, faster settling rates should result if coagulation of particles could be increased. Experiments have been conducted for a period of several months in the Allis-Chalmers laboratory to study the effect of sonic vibrations on settling of particles of different sizes and concentrations. Apparatus The sedimentation apparatus used in these experiments is illustrated in Figs. I and 2. The essential features are the stationary field coil and the movable voice coil. Both windings are placed around a solid iron core. A leather diaphragm connected to the steel frame holds the voice coil in place. A brass rod is fastened to the voice coil with a metal disk connected to the other end. This disk is sealed to the lucite cylinder with a flexible rubber diaphragm. The lucite tube is 17 in. long; its inner diameter is 2½ in. and the wall thickness is ¼ in. The tube is calibrated on the outside in 10 c.c. divisions for a total of 1000 cubic centimeters.

Jan 1, 1947

By Lewis Blanchard Brown

It is my purpose in the following paper to describe the south-central part of Siberia, with special reference to its geology and the mineral deposits. This region is known politically as the Achinsk and Marinsk districts of the Tomsk Government. It is situated among the Altai mountains, in. ]at. 50° to 55O n and long. 87O to 93O E., not far from the northern frontier of Mongolia, and is divided as follows: Mining Districts.—(1) The Tomsk mining district, including the political districts of Altai (belonging to the private crown lands of the Russian Emperor) and Marinsk; (2) the AchinskMinusinsk mining district, including the political districts of Achinsk and Minusinsk; and (3) the North Yenisei mining district, situated in the northern part of the Yenisei political district of the Yenisei Government. Fig. 1 is a map of the Tomsk mining provinces, showing the useful mineral-deposits, excepting those of gold, and giving the routes of the railroads and post-roads connecting the various districts. Political Divisions.—The Tomsk Government is sub-divided into seven " oojesdy " or districts, as follows: Barnaul; Biisk; Kuznetsk; Kainsk; Kolyvan; Marinsk; Narim; and the Altai district (private land, as above). The Yenisei Government is sub-divided into five "oojesdy" or districts, as follows : Erasnojarsk ; Kansk; Yenisei; Achinsk; Minusinsk. Concerning the geology of the region, in addition to the record of my own observations, references will be made to the works of earlier writers. These have been consulted for the purpose of comparison, as regards the districts which I have actually traversed, and for the purpose of completing my account of such portions as I have not been able to visit.

Jan 1, 1904