Search Documents

By W. N. Tanner

The wire-rope hoisting conditions at the mines of the Anaconda Coppcr Mining Co. in Butte, Mont, are very severe because of the conditions under which it is necessary to operate. A study was made, in the fall of 1919, for the purpose of changing these conditions in order to obtain longer rope and sheave life. There are at present in Butte hoisting engines equipped with wire rope as follows: 9 main hoists using flat ropes. 7 main hoists using 1 1/2-in. rope. 5 main hoists using 11/4-in. rope. 6 shafts using 11/8-in. rope. 2 chippy hoists using 11/4-in. rope. 9 chippy hoists using 11/8-in. rope. 15 shafts using 1-in. rope. 7 shafts using 7/8-in. rope. 1 shaft using 3/4-in. rope. In addition, there are a number of sinking engines wing 5/8-in, 3/4-in., 7/8-in., and 1-in. (15.9, 10, 22, and 25 mm) rope. THe flat ropes run from 1/2 by 71/2 in. (12.7 by 1905 mm.) to-3/8 by 4 1/2-in (9.5 by 114 mm.) and are used on the older hoisting engines, which arc set comparatively close to the shaft. Because of swelling and moving ground at some of the shafts, these ropes present certain difficulties ill operation that are more pronounced than with round ropes; they are, therefore, being superseded by round ropes as newer engines are being installed. They are, however, much more easily inspected and repaired than round ropes. In general, the practice in Butte is to use hoisting engines equipped with 12-ft. (3 7 m.) cast-iron drums, smooth faced, for 11/2-in. rope and 6-ft. cast-iron drums, smooth faced, lagged with 3/8-in. steel plate for 11/4 l1/8 and 1-in. (31.7, 28.6, 25 mm.) rope in main and chippy shafts. Cast-iron head sheaves, 12, 10, and 6 ft. in diameter, with grooves

Jan 1, 1923

By W. N. Tanner

The wire-rope hoisting conditions at the mines of the Anaconda Coppcr Mining Co. in Butte, Mont, are very severe because of the conditions under which it is necessary to operate. A study was made, in the fall of 1919, for the purpose of changing these conditions in order to obtain longer rope and sheave life. There are at present in Butte hoisting engines equipped with wire rope as follows: 9 main hoists using flat ropes. 7 main hoists using 1 1/2-in. rope. 5 main hoists using 11/4-in. rope. 6 shafts using 11/8-in. rope. 2 chippy hoists using 11/4-in. rope. 9 chippy hoists using 11/8-in. rope. 15 shafts using 1-in. rope. 7 shafts using 7/8-in. rope. 1 shaft using 3/4-in. rope. In addition, there are a number of sinking engines wing 5/8-in, 3/4-in., 7/8-in., and 1-in. (15.9, 10, 22, and 25 mm) rope. THe flat ropes run from 1/2 by 71/2 in. (12.7 by 1905 mm.) to-3/8 by 4 1/2-in (9.5 by 114 mm.) and are used on the older hoisting engines, which arc set comparatively close to the shaft. Because of swelling and moving ground at some of the shafts, these ropes present certain difficulties ill operation that are more pronounced than with round ropes; they are, therefore, being superseded by round ropes as newer engines are being installed. They are, however, much more easily inspected and repaired than round ropes. In general, the practice in Butte is to use hoisting engines equipped with 12-ft. (3 7 m.) cast-iron drums, smooth faced, for 11/2-in. rope and 6-ft. cast-iron drums, smooth faced, lagged with 3/8-in. steel plate for 11/4 l1/8 and 1-in. (31.7, 28.6, 25 mm.) rope in main and chippy shafts. Cast-iron head sheaves, 12, 10, and 6 ft. in diameter, with grooves

Jan 1, 1923

Edward Keller, Baltimore, Md. (communication to the Secretary): When, at the New Pork meeting, February, 1899, Mr. Douglas gave an abstract of his highly interesting paper on the Copper Queen mine, he invited the members of the Institute, in his usual progressive spirit, to make a full scientific investigation of the region of that mine during the prospective excursion to Bisbee, Arizona. I volunteered to examine some of the metallurgical processes and products of the works, and obtained from Mr. Douglas a valuable series of samples. Upon the issue of his paper, however, I found that he had already a considerable volume of analyses of those products, and that little was left for me to do in that respect, except to duplicate his results, the importance of which work would not have been commensurate to the time and labor involved. I selected, therefore, only some points which he had not made entirely clear, or concerning which I was skeptical. The details of most of my work will appear in a future paper. From Mr. Douglas's figures I have calculated the values for the elimination of impurities in the so-called Leghorn converter, introduced by him at the Copper Queen works, and have found them to be as follows: Percentage of Elimination of Impurities in Pour Blows of a Converter. No of ' Selenium Sulph'r Iron. Zinc. I Nickel. Lead. Antimony Arsenic. and Blow- ! Tellurium .. 1.......... 99.4 99.6 88.0 92.6 94.4 81.6 83.8 40.3 2.......... 99.0 99.6 98.1 92.5 96.8 71.9 76.6 38.1 3.......... 98.8 99.5 93.5 91.4 96.3 63.8 80.6 25.3 4.......... 99.8 99.5 95.8 95.8 97.5 65.3 76.9 36.3 Average 99.2 99.6 93.8 93.1 . 96.2 70.6 ! 79.5 35.0

Jan 1, 1900

By Paul M. Tyler

DOES mining pay? Inasmuch as the whining of minerals from Nature is one of the world's principal sources of new wealth, this question is of general economic interest but it is obviously of even more vital concern to investors and those engaged in mining. In a previous article on "Wage Costs in the Mineral Industries,' published in the November issue, I attempted to show that wages paid workers on the job accounted for, roughly, 50 per cent of the mine dollar. Salaries normally range over 5 per cent - lower for large metal mines but higher in stone quarries and minor nonmetallic min. in, industries. Purchases of supplies, materials. fuel, and power generally aggregate within the range of 15 to 25 per cent of total receipts, with the average well under 20 per cent. The total of all such specified expenditures which may he loosely described as

Jan 1, 1934

By R. W. Brauchli

The author has made a statistical analysis of the relations between recovery and length of cores, diameters of cores and of drill pipe, and cost of coring under different contractual conditions. The data are presented in tabular form. The length of the core appears to play a minor part in the percentage recovered, with a tendency to lower percentages with increased core length; approximately 50 per cent of the length cored is normally recovered if the cores are more than 2 in. in diameter. The diarneter of the core has a more pronounced influence on the recovery; 1 3/8-in. cores average 29.1 per cent, 2 1/8 -in. core 53.4 per cent and 3 1/8-in. cores with 6 5/8-in. drill pipe 68.5 per cent. Where 31/8-in cores were taken with smaller diameter drill pipe, i. e., 4 1/2 - in. drill pipe in 8 1/4-in. hole, the recovery dropped to 49.8 per cent, indicating that the more rigid drill pipe favors good core recovery, a conclusion also borne out by the results obtained in using large drill pipe for smaller diame-ter cores. Surprisingly good recoveries were obtained from both the Johnson and Simpson sands; shale, limestone and dolomite each gave less then average recoveries. No serious fishing jobs resulted from coring operations. Attention is called to the need of a core drill which will make it possible to drill a full-sized hole while coring, and thus reduce the cost of cores. Data pertaining to core drilling should be consistently recorded, such as, diameter of drill pipe and collar, diameter of core, recovery, size of cutter heads, type of core-barrel, coring time, speeds of rotation and of pumps, weight on core-barrel, etc.

Jan 1, 1933

By Leroy Gardner

EVERY reader of this paper is well aware of the fact that the prolonged inhalation of large amounts of free silica dust results in fibrosis of the lungs, and that other inorganic dusts, except those of asbestos and the mineral poisons, are thought to be relatively harmless. But probably few have had opportunity to visualize the effects of silica, asbestos and other minerals upon living tissues. The ideal demonstration would be based upon sections of lungs from human beings that had inhaled com-parable concentrations of different dusts for a unit period of time. Such material is generally difficult to obtain and in some instances is of ques-tionable value because the subject has been exposed to more than one kind of dust. A demonstration could be prepared from the lungs of animals. However, so many months or even years are required to com-plete the exposure to each kind of dust that enough material has not been accumulated. For a general survey of the action of different types of dust, I am therefore compelled to use the tissues of animals that have been injected with suspensions of dust particles. The injection method offers certain advantages. The quantity, the particle size and the state of dispersion can be controlled with sufficient accuracy so that the tissue responses to different minerals can be accu-rately compared. The method insures contact between the tissues and the mineral particles; protective mechanisms, which may prevent the inhalation of certain types of foreign body, never come into play. If the pathway of injection be one that minimizes nonspecific injury, the tissue responses may simulate those produced by inhalation but they develop somewhat more rapidly. It should always be remembered that injection methods merely demonstrate the capacity of various kinds of minerals to provoke reaction in the tissues; whether the same substances are inhaled from atmospheric suspension and accumulate in the lungs in dangerous quantities can be demonstrated only by inhalation.

Jan 1, 1938

By Norman D. Fitz Gerald

THE growth of domestic requirements for motor fuel has been phe-nomenal, rising year after year in a fashion almost unique among com-modities, resisting depressions and forging rapidly ahead in times of prosperity. Consumption advanced from 226 millions of barrels in 1925 to 522 millions of barrels in 1938; or 130 per cent. The economic influ-ences generating and sustaining this demand are of vital concern to the petroleum industry. The general factors affecting utilization of motor fuel are well known but it is the purpose of this paper to employ the recently developed technique of economic dynamics to describe them mathematically. Such problems in economic analysis are complicated by the freedom of all the variables to fluctuate, their mutual interdependence, changing incidence upon one another, and the nonquantitative character of some of them. Economic quantities and relationships, unlike those of the physical world, are continuously changing and this dynamic characteristic is both a distinguishing and confusing feature in economic research. The com-plexities of the problems require application of the analytical devices of mathematical statistics to uncover the probable relationships between factors. The procedure employed is to formulate a logical relationship linking the dependent to the independent variables, and then simul-taneously, rather than sequentially, determine their separate effects by multiple correlation. This transformation of common knowledge to quantitative terms makes it possible to measure the probable effects of changing conditions upon requirements, assisting in the sound interpreta-tion of economic policies. The utility of the results of such dynamic analysis is in sharp contrast to the sterility of the trends and other simple empiricisms of descriptive statistics. It is not intended in this study to throw light on the reasons why any motor fuel at all is consumed; but to discover relationships explaining why more was consumed at one time than at another. Specifically the prob-lem is confined to the measurement of the influences of statistically

Jan 1, 1940

F. G. SMITH, Waterbury, Conn.-I would like to ask whether small amounts of iron give the maximum resistance at a low temperature, and if the large amounts of iron raise the temperature at which the maximum resistance occurs? That is, with a small amount of iron, will a maximum be at, say, 10°? F. E. BASH.-With the small amount of iron, the maximum is at a lower temperature, and with the increase of iron, the maximum increases; it seems to come to a maximum and then decrease; that is, increasing the iron up to a certain value increases the temperature at which there is a maximum of resistance, and any increase of iron beyond that value will start decreasing this temperature. With 2 per cent. of iron, the maximum is lower than for 1.5 per cent. which was the value that we found to be satisfactory. F. L. DRIVER,* Jr., Harrison, N. J.-I would like to ask what chance there is of the instrument companies getting together and deciding on standards for both manganin and constantan? We make both of these alloys in this country and we find that each one of the instrument com-panies who buy these materials require different standards of specific electrical resistance and thermal e.m.f. For instance, some of our cus-tomers require an electrical resistance in manganin or therlo of 240 ohms per circular mil foot and others require it with a specific electrical resist-ance of 270 ohms per circular mil foot. They buy these alloys in relatively small quantities so that it means much extra melting and supervision when making up small quantities for each consumer. If something could be. clone to eliminate this, it would be a benefit to the instrument com-panies, who could secure their material more cheaply, and to the manu-facturers, who would not have to spend so much time and effort in special manufacturing.

Jan 12, 1919

By Jacob T. Wainwright

This stove has been designed to meet the requirements of a fur nave that must be operated with either a reducing or a neutral flame ; and more particularly to make feasible the operating of re duction-furnaces with the cheaper grades of gas-fuel, which has heretofore been impracticable. In general, cheap gas-fuels result from incomplete combustion, and, being suited for further combustion, answer very well for heat ing purposes; and high temperatures may be attained with them, when they are used in conjunction with regenerative stoves. But, in operating a reduction-furnace, a high temperature is not the only requirement. It is also necessary that the fuel shall not be cansumed beyond a certain degree, in order to insure a re ducing flame for the reduction-process ; consequently, it becomes necessary to dispense with combustion as much as possible previous to the use of the fuel-gases in the reduction-furnace. Moreover, these gases must be preheated to a high degree, in order that a sufficient temperature may be maintained in the furnace; and, since this preheating cannot be accomplished by a previous, partial combustion of the gases themselves, it follows that the stoves for pre heating these gases should be heated to as high degree as it is pos sible to attain with an inferior fuel. This result can best be accom plished by complete combustion of the heating gases, and is further facilitated by preheating all of the air and gas used for this com plete combustion. It is more particularly desirable to preheat the air, since the combustible gases used may generally be obtained directly from the furnace, or gas-producer. The reducing gases, escaping from a gas-fuel reduction-furnace, are capable of considerable further dilution with air to secure com plete combustion, and consequently may be utilized for heating the stove to a high temperature, provided the air be sufficiently preheated.

Jan 1, 1889

By R. P. Abendroth

This study is concerned with the kinetics of selective oxidation of chromium in a commercial Fe-Cr-Ni alloy. Selective oxidation of chromium in this alloy, by use of a low oxygen-potential atmosphere, leads to the formation of a compact, protective layer of Cr2O3. This layer serves to protect this alloy from gross scaling when it is subsequently exposed to severe oxidizing conditions at high temperature. The interaction of low oxygen-potential atmospheres close to equilibrium with Fe-Cr and Ni-Cr alloys has been studied by others."' These studies werk concerned with the surface-structure variations under slightly oxidizing conditions. NO detailed study was made of the oxide scale formation kinetics, however. The alloy samples were cut from 0.012-in.-thick sheet, with an apparent surface area of 7.1 sq cm. These sheet samples were abraded through 4/0 metallographic paper, and washed in alcohol and acetone. The analysis of the sheet alloy is (in weight percent): 42 pct Ni, 5.5 pct Cr, 0.09 pct C, 0.18 pct Al, 0.36 pct Si, 0.26 pct Mn, balance Fe. The weight gain vs time data were obtained with a 2-g capacity fused-silica spring—cathetometer system. The spring deflection was optically magnified ten times before being read by the cathetometer. A sensitivity of about 0.01 mg was attainable. The spring was enclosed in a water jacket maintained at 60°C to minimize the effect of temperature changes. The sample was suspended from the spring with a fused-silica hangdown and was positioned in the thermal center of a mullite furnace tube. Sample temperature was read with the aid of a thermocouple placed outside the mullite tube and an inside vs outside temperature calibration. Temperature change during the course of a run was ±0.25°C, with a temperature gradient of less than l.O°C over the length of the sample. Total temperature uncertainty was no more than ±3.0°C. Alignment difficulties between the hangdown and radiation shields in the furnace tube required that the sample be positioned in the furnace when cold, and heated with the furnace until the temperature stabilized at the desired point. This required 5 to 6 hr, and was carried out in Matheson ultrahigh-purity hydrogen. Oxidation was started, after evacuation, by introducing a hydrogen-water vapor mixture, obtained by saturating hydrogen with water vapor at 31.00o ± 0.02oC. Oxidation was continued for 90 min. Gas flow was 300 ml per min during heat up and oxidation. Since only several milligrams of oxide are formed on each sample, chemical analysis of the oxide is difficult. A representative analysis is: 80 pct Cr2O3, 5 pct Fe2O3, 3 pct Al2O3, 4 pct MnO, 7 pct SiO2, 1 pct or less NiO. X-ray diffraction analysis of the oxide as formed on the alloy gives rhombohedra1 Cr2O3, and barely distinguishable amounts of a cubic spinel phase, and possibly AlZOs and SO2. The identification of these latter two compounds is by no means certain. The spinel phase could be based on iron or manganese as these elements are present in significant amounts in the oxide. The results of the kinetic studies using 31°C dew-point hydrogen-water vapor mixtures were found to conform to a parabolic rate law. In many cases the parabolic plot consisted of two intersecting straight lines, defining an early and a late rate for a particular run, and in the other cases the parabolic plot consisted of one straight line for the entire run. The slopes of the various straight lines were determined by the method of least squares. Reproducibility of the data was good enough for multiple runs at the same temperature such that the value given for the rate constant is the average for two or more closely similar values, rather than widely varying values of the rate, where more than one determination is indicated in Table I. The exhibition of only one or of two rate constants during a run can happen at the same temperature. Thus, Table I shows that at 11'74°C a single rate constant was obtained from one sample, while other samples oxidized at the same temperature gave an early and a late rate constant. It should be noted that the single rate constant corresponds very closely with the early rate constant. This is also true at 1153°C. The time at which the late rate started to appear was variable, usually occurring 20 to 40 min after oxidation had started.

Jan 1, 1964

By William T. Folwell

The Lucky Friday mine east of Mullan, Idaho, is an outstanding example of a property in the Coeur dlAlene district where a small and insignificant-appearing silver-lead-zinc vein at the surface has changed at depth into a large vein of great importance. The Lucky Friday vein has little if any surface expression and above the 1200 level the ore shoots are small and discontinuous. Between the 1200 level and 2450 level, the lowest developed level, the main ore shoot has shown remarkable improvement on each succeeding lower level, and today the mine is one of the major lead-silver producers in the Coeur d'Alene district. History: The Lucky Friday property is on the north side of the South Fork of the Coeur d'Alene River in sections 25, 26 and 35, T. 48 N., R. 5 E., Hunter mining district, Shoshone County, Idaho. This is about one mile east of the town of Mullan, which serves the eastern portion of the Coeur d'Alene district. The southern part of the property is crossed by a branch line of the Northern Pacific Ry. and by U. S. Highway 10. This highway is the principal road crossing the panhandle of Idaho and connects the district with Spokane, Wash., on the west and Missoula, Mont., on the east. The main portal and surface plant of the Lucky Friday mine is at an elevation of 3365 ft, only a short distance above the valley floor and a few hundred feet from U. S. Highway 10. so the mine is readily accessible for year-round operation. The property is comprised of six claims, known as the Lucky Friday group, owned outright by the Lucky Friday Silver-Lead Mines Co. There are four patented claims, Good Friday, Lucky Friday, Northern Light, and Lucky Friday Fraction No. 2 (Mineral Survey No. 3028), and two unpatented claims, Hunter and Creek. In addition, Lucky Friday owns an undivided one-half interest in the Hunter Creek property. which adjoins the Lucky Friday group on the north: a 90 pct interest in the mineral rights in the Jutila Ranch (160A), which adjoins the Lucky Friday group on the east; and a 60 pct interest in the Lucky Friday Extension claim group, which adjoins the Lucky Friday group on the west. The company also has a long-term mining lease on the Hunter Ranch, which adjoins the Lucky Friday group on the west. The claims of the Lucky Friday group were located between 1899 and 1906. The Lucky Friday Mines Co. was organized in 1906 and did considerable exploration work by surface trenching and shallow underground workings, only to see the property sold by the Shoshone county sheriff to satisfy labor claims totaling $2000 in 1912. Another firm, Lucky Friday Mining Co., bought the claims in 1914 and spent 12 years driving what is now known as the tunnel level crosscut. This tunnel intersected a vein previously exposed in a higher tunnel, but it was only a few inches wide. The vein was followed a short distance westerly but was so unpromising that the work was discontinued in favor of extending the main crosscut tunnel several hundred feet north. No ore was found and all work was discontinued. The property was held in such low esteem by the firm that it let taxes amounting to less than $15 a year go delinquent for nine years. Then the property lay idle for two more years until in 1938 John Sekulic, a Mullan service station operator, took a lease, with a $15,000 purchase option, on the advice of an old miner who had worked in the mine. Sekulic re-opened the tunnel level crosscut and explored the vein with an easterly drift for about 200 ft. The vein was too narrow to be of commercial value but was believed interesting enough to warrant further exploration at depth. Lacking funds to explore the vein at depth, Sekulic tried to get the district's larger operating companies to take over his lease and option. They were not interested because of the lean tunnel level showing and the fact that the property lay between the White Ledge fault on the north and Osburn fault on the south, an area which geologists always considered unworthy of exploration. Sekulic then organized the present company and assigned his lease and option to it for stock. This was in 1939. Enough stock was sold locally to finance sinking of a shaft 100 ft from the tunnel level east drift. The vein at this additional depth still was not commercial but showed some improvement. Treasury stock was offered at 5 to 10C a share

Jan 1, 1959

By Roland J. Lapee

A history of the progress made in copper refining in Montana is presented. The casting furnaces and the newly rebuilt electrolytic refinery are descmbed and operating details are given. Experiences with various addition agents, effects of rernoval of chlorine from the electrolyte, and effects of separan on electrolyte and on copper deposit are discussed. Observatzons are made on the effect of various impurities in anode copper and behavior of thezr salts in electrolyte and in slime, on treatment of slime for removal of copper, and on electrolyte puriification problems. The improved method for production of starting sheets is described. Attention is given to new materials for construction and to improvement in matrials handling ad quality control. COPPER refining at Great Falls, Montana, dates back to 1892. The original plant produced 65,000 lb. of cathodes per day at a current density of 16 amp per sq ft. In this plant anodes and cathodes were handled to and from the cells by means of hand-operated chain blocks and were moved about the plant by hand trucks. Cathodes were melted in coal-fired, reverbera-tory furnaces, were charged by hand, and refined copper was dipped by hand and cast in iron molds. In 1916, a new, modern plant with capacity to refine 18 million Ib. copper per month was built. Two refining furnaces were built, and each was provided with a twenty-mold Clark casting wheel. In 1922, the furnaces were converted to the use of pulverized coal: in 1923, to the use of oil; and in 1928, to the use of natural gas. In 1926, the plant was enlarged 50 pct. The use of pulverized coal for refining copper at Great Falls was discussed1 in a paper presented at the Salt Lake City meeting of the Institute in September 1925. Also, a comparison of the use of various fuels in copper refining furnaces was discussed 2 in a paper presented at the New York meeting of the Institute in February 1932. Prior to 1943 the cellroom was operated with twenty-five 720-lb. anodes and 26 cathodes per cell. Four cathodes, each weighing about 165 lb., were produced from an anode. In 1943 the weight of the anode was reduced to 460 lb., and two cathodes, each weighing about 190 lb., were produced from an anode. In 1949, a Billet Casting Wheel for the production of 3 in. diam phosphor deoxidized billets was built. A paper, presented at the New York Meeting of the Institute in February 1956, describes3 this plant and operation. In the electrolytic refinery, production is controlled by variation of the current density. In 1956, germanium rectifiers on a separate electrical circuit were provided for the starting sheet section so that current density could be maintained at any desired figure. Also in 1956, a program of modernization and enlargement of the Electrolytic Copper Refinery was started. This program, when completed, will raise the capacity of the Great Falls Electrolytic Copper Refinery approximately 33 pct, to 33 million lb. of cathodes per month. Furnace capacity for melting cathodes and anode scrap is ample to take care of the increased production from the electrolytic refinery. This fortunate condition came about primarily as the result of the three following changes: 1) The furnaces were lengthened 10 ft in 1922 when the fireboxes were found unnecessary for burning powdered coal. 2) Furnace life, and hence furnace capacity, was increased by the successful efforts of the Copper Refinery staff to develop a method for sanding furnace side walls and roof. 3) The natural gas being used has a very low sulfur content. As a result, it is possible to reduce time spent rabbling and poling and thus greatly increase tons per furnace charge. TANKHOUSE AND TANKS The Great Falls Electrolytic Refinery is 535 ft long by 252 ft wide. The cells are arranged in four crane bays in which are operated seven 10 ton Whiting Cranes. The old cells are in groups of ten, with circulation of electrolyte through five cells in cascade and with aisles between the groups of ten cells. The new cells are nested in groups of sixteen with no aisles, are all on one level, and have individual circulation to each cell. Present plans call for 1792 commercial cells and 128 stripper cells. To reduce confusion during the construction period, and to use the cranes, cars, and other equipment already on hand, the cells in the rebuilt section were designed to have approximately the same inside dimensions as the cells in the old part of the

Jan 1, 1962

By B. M. Larsen, T. E. Brower

A perspective is presented of the steel plant sulphur distribution and elimination problem from coal to liquid steel ready for teeming, giving distributions of sulphur over a range of coke sulphur content, and some methods of sulphur control, in the blast furnace, external desulphuriza-tion between blast furnace and open hearth, distribution between fuel, slag, and metal, and methods and limitations of control of sulphur in the open hearth furnace. AS a part of the 1951 AIME symposium on sulphur in steelmaking, it was thought that a discussion of the distribution of sulphur throughout the whole series of operations, from coal and ore to finished steel ingots, might have some value in giving a perspective on the whole problem. The following discussion is an attempt to present such an overall picture. The order is that of the actual plant operations, beginning with a very brief consideration of the coking process. Sulphur in Coal and Coke Since by far the largest source of sulphur entering the steelmaking cycle is in the coal used to make coke for the blast furnace, it would seem reasonable to eliminate some of it, either from the coal, or the coke, or during the coking process. This has appeared impracticable up to the present, at least, for two main reasons: the low activity of the organic sulphur in either coal or coke, and because of price limitations involved in treating a low cost material such as coke. A variable portion, usually M or less, of the sulphur is present in coal in the form of pyrites or similar compounds, and a large part of this sulphur may be removed in the coal washery. Most of the sulphur, however, is normally present as "organic" sulphur, intimately associated with the coal structure. Its distribution prevents any separation by mechanical means. Its low activity makes improbable ' any rapid chemical removal, although hydrogen will remove sulphur from both coal and coke. Thus, prolonged recirculation of coke oven gas in the coking process would tend to leave a smaller percentage of the total sulphur in the coke residue. Table I shows a typical distribution of sulphur from coal into products in the coking process. As the sulphur in the coal increases, the sulphur in the coke tends to increase in about the same proportion. Sulphur in the Blast Furnace The best picture of the situation in the blast furnace is provided by a sulphur balance of raw materials entering, and of products leaving, the furnace. The difficulties in accurate weighing and sampling of the variable solid materials entering this process, and the number of hours required for the raw materials to descend through the furnace under variable operating conditions, make it difficult to obtain an accurate balance. However, balances made over periods of weeks or months tend to average out some of these uncertainties. Table I1 presents three typical sulphur balances similar to a number that the writers have calculated. In most of these the slag volume calculated from the sulphur balance is, in some instances more, and in other instances less, than the value corresponding to the best input and output balances of the other slag constituents (lime, silica, alumina, etc.). Probably the greatest source of error in these calculations is the sulphur content of the slag. Despite some possible inaccuracies the balances of Table II show rather definitely the following points: 1—That 87 to 95 pct of the total sulphur input is in the coke and 95 to 97 pct of the total sulphur output is in the slag. Also, that if any sulphur leaves the furnace with the gas it is relatively small, amounting to a possible 1 pct or less. 2—At the lower sulphur coke level of 0.86 pct the total amount of sulphur charged is 15 Ib of sulphur per ton iron increasing to 26 lb per ton at the higher sulphur, intimately associated with the coal struc-rare burdens containing sulphur-rich ores will the total sulphur burden fail to be nearly proportional to the content in the coke used. 3—The 7 to 9 pct of the total sulphur input from the limestone of furnaces B and C is due to the relatively high sulphur content of the stone, 0.226 and 0.265 pct, respectively. In the case of furnace A, the sulphur content of the limestone was only 0.06 pct which resulted in only 3 pct of the total sulphur input coming from this source. It is rather interesting to compare the sulphur balances of a typical ferromanganese furnace with

Jan 1, 1952

By Harry A. Lipsitt, Douglas Y. Wang

A fatigue study in completely reversed axial tension-compression has been perforried on high-purity titanium and on three high-purity alloys of titanium. The alloys each contain approxi7nately 0.75 at. pct of a single interstitial element; carbon, nitrogen, and oxygen, respectivley. The results corroborate a previously published theory which proposed that strain aging under alternating stress was responsible for the fatigue limit behavior of certain alloys. The present data indicate that in these alloys an increasing strain-talline aging effect under alternating stress is provided by oxygen, carbon, and nitrogen, respectively. CURRENT research on the nature of the fatigue limit in metals suggests that the presence of a fatigue limit in metallic materials is a manifestation of strain aging that occurs under alternating stress.lm5 A comprehensive theoretical model based on the above hypothesis has been developed to explain the existence of a fatigue limit.' This model also provides increased insight into several other fatigue phenomena as under stressing, overstressing, and coaxing effects. The theory, as well, provides equal understanding for those cases where no real fatigue limit is observed. Briefly, this theory assumes that the S-N curve for a pure metal is a smooth function of the applied stress, and the effect of adding an element that is soluble (or forms a precipitate) in the pure metal is simply to shift the S-N curve to the right. If the added element confers the power to strain age, the result is a further shift of the S-N curve, this time upward and to the right. Since strain aging is not expected to be a strong function of stress, and since damage per cycle is known to be quite stress dependent, it is to be expected that there will be some limiting lower stress at which the strengthening due to strain aging will balance the damage due to crack propagation. This stress is the fatigue limit. The position of the fatigue-limit knee was thought to be a function of the magnitude of the strain-aging effect on both the finite and infinite life portions of the S-N curve. Although the strain aging hypothesis seems to be reasonably valid for bcc materials,2'6 it needed to be tested for both fcc and cph metals. This report is the first of a series concerning the fatigue-limit behavior of titanium with varying amounts of the interstitial solutes (C, N,, and 4) that are known to cause static strain aging in titanium. Yield-point effects have been reported for polycrys-talline high-purity titanium alloys containing either carbon, nitrogen, or oxygen.7'9 These effects were observed at testing temperatures in the range 100 to 300'. In addition yield-point and strain-aging effects have been reported for single crystals of titanium containing 0.1 wt pct C plus N.' These yield points were observed over a wide temperature range, but no room-temperature aging occurred. Aging at 180' was required to cause the return of the yield point. The magnitude of the yield phenomena in titanium containing interstitials is not expected to be as large as is observed in bcc metals because of several factors. Titanium has a very high chemical affinity for oxygen and nitrogen. The thermodynamic stability of solutions of oxygen or nitrogen in titanium is recognized. Lattice parameter measurements of titanium containing arbon, oxygen,1° or nitrogen" show that the "c" parameter is expanded more than the "a" parameter, but that up to about 2 wt pct this results in an insignificant change of the axial ratio 'c/a." Ehrlich" has shown that the sites occupied by interstitial atoms in titanium are spherically symmetrical and therefore a lattice expansion, at a constant c/a ratio, results in a simple dilation of the interstitial site. Such a dilation involving no shear has been shown to react only with edge components of dislocations.13 This causes only a weak pinning action. Shear stresses would be anticipated locally when only one of the two interstitial positions was occupied. The carbon atom will cause a symmetrical distortion of the lattice whereas the oxygen and nitrogen atoms have, in addition, the previously mentioned chemical affinity of titanium for these elements. These factors will result in a considerably smaller reduction of free energy upon the association of interstitial atoms with dislocations, and therefore a much weaker pinning than has been observed for the bcc metals. These considerations would lead to the hypothesis that of the interstitial elements considered here carbon would cause the strongest pinning effect in titanium where the amount of interstitial in solution is constant. This hypothesis will be borne out in the analysis of the present results.

Jan 1, 1962

By F. M. Morris

A large reserve of thick coal in southwest Virginia was developed by Clinch-field Coal Co. in 1957-1958 to produce a nominal rate of 1500 tph raw coal. Operation features coal cleaning in transit. Refuse removed averages 35 pct. Evolution of plant from initial conception to completion is discussed, selection of means applied is explained, and performance to date us design expectation is described. The long-range plan calls for ultimate handling capacity of 40,000 tpd raw coal with anticipated clean coal capacity of 26,000 tpd on a three-shift basis. From a materials handling viewpoint, the Moss No. 3 operation is principally of interest as an ensemble. Generally speaking, it uses time-tested equipment and ideas but some of these are employed on a scale that may be new in the industry. At present about 20,000 tpd of raw coal are being handled. This is expected to increase to 40,000 tpd as soon as business conditions justify it. The purpose of this paper is to discuss the evolution of the plant as to materials handling practices, to describe briefly the equipment and methods used, and to comment on performance in certain areas. The subject divides itself naturally into four phases: 1) operations at the mines, 2) transportation from mines to plant, 3) raw coal handling into the plant, and 4) transportation of refuse away from the plant. OPERATIONS AT THE MINES The coal reserves for Moss 3 are in southwest Virginia where Dickenson, Russell, and Buchanan Counties come together. This area contains about 15 square miles and over 100,000,000 tons of coal. Here the No. 4 (Tiller) and No. 5 (Jawbone) seams of the Norton Formation lie so closely together that for practical purposes, they constitute one seam of coal. This seam, which is called the Thick Tiller, varies from 10 to 18 ft in thickness and underlies Sandy Ridge, a mountain cresting between 2400 and 3300 ft above sea-level. At 18-ft seam height (which is considered to be the maximum practical mining height) the parting between seams will be about 3 1/2 ft thick and each bench of coal will be about 7 ft thick. Depending on the amount of impurities in the seams Drover. total reject in this height coal may approximate 50 pet by wt. It will average about 35 pet for the property as a whole. The first move in developing this resource was made in 1953 when contour maps of several square miles around Duty, Va., including all the known outcrop, were made by photogrammetry. At this time, it was felt the prospective operation would be served by the Clinchfield Railroad and a photogrammetric route survey was made by this railroad from Haysi to Duty. Study of the resulting maps indicated only one site—adversely owned—which might accommodate the size washing plant to be erected. Water resources of a dependable nature seemed nonexistent. In 1954 bulk washability tests were made on the Tiller Bench at the Moss No. 1 preparation plant. The tests indicated this portion of the seam, mined separately, would wash to 4 pet ash with good recovery. Also in 1954, development of Moss No. 2, south of Sandy Ridge, was begun. This mine is in the Tiller Seam where it is about 100 ft below the Jawbone Seam. The reasons for developing a mine in the normal Tiller Seam before tackling the Thick Tiller seemed compelling: Railroad service could be established quickly, communications were better (though not good!), more was known of the seam (it had been mined in the years 1911 to 19241, and there was no essential property to be acquired. After some legal skirmishing, the Norfolk & Western Railroad was granted the right to serve the new mine. Three decades earlier the old mine had been served by the Clinchfield Railroad. The event which triggered active development of Moss 3 was the Appalachian Power Co.'s decision in 1956 to build a 450,000-kva power plant on Clinch River at Carbo. This solved the problem of marketing the steam coal which inevitably must be a product of a mine in the Thick Tiller. Management promptly decided to build the preparation plant at Carbo where an excellent site was owned; where railroad service existed; where telephone service could be obtained; and where roads, bridges, and water supply were tolerable.

Jan 1, 1961

By Edna A. Dancy, Gerhard J. Derge

The specific conductance of FeOx,-CaO melts in contact with iron was found to decrease from 200 ohm-1 cm-1 for FeO, to 40 ohm-1 cm-1 for a melt containing 26.3 pct CaO at 1400°C. The temperature coefficient was positive at all compositions, but became smaller at high CaO contents. Current efficiencies for electrolysis increased from 2.5 pct in FeOx to 17.3 pct at the high CaO composition, indicating a change from predominantly electronic conduction to conduction with a substantial ionic contribution. It was shown that Ca++ ions as well as Fe++ ions carry the ionic current. A subsidiary investigation on the apparent effect of atmospheres of argon, helium, and nitrogen on the electrical conductivity showed that this could be correlated with surface temperature losses, which varied with the thermal conductivities of the gases and resulted in precipitation of metal by the reaction 3 Fe++ = 2 Fe+++ + Fe. The work described in this paper is offered as a contribution to the general fund of knowledge concerning metallurgical slags. Measurement of electrical conductivity and electrolysis are comparatively trouble -free methods for investigating molten materials, but, although these methods had been used for complex slags, it was not until the work of Bockris et al.1 that the approach of examining simple binary slag systems was employed, and CaO-SiO2, MnO-SiO2, and Al2O3-Si9 were studied. Two groups have performed work of particular relevance to the present investigation. Inouye, Tomlinson, and chipman2 studied the conductivity of wustite as a function of temperature and of the addition of 5 mol pct of a number of oxides, including CaO. They concluded that molten FeOx in equilibrium with iron is a semiconductor. Simnad, Derge, and ceorge3 demonstrated the ionic nature of liquid iron silicate slags and also concluded that, although the conductivity of FeOx in equilibrium with iron is predominantly electronic in nature, there is a small ionic contribution. The work reported here on FeOx,-CaO slags consists of three main parts, namely, the determination of the specific conductance over a wide composition range, an investigation into the nature of the conductivity through current-efficiency measurements over the same composition range, and an attempt to identify the current-carrying ions, as well as a subsidiary investigation on the apparent effect of the nature of the inert atmosphere on the conductivity. EXPERIMENTAL Materials. The slags, varying in composition from FeOx to 27 pct CaO, were prepared by heating reagent- grade Fe2O3 in an ingot iron crucible with a suitable amount of CaCO3 and, in some cases, powdered iron, in air. This prefused material was then used for the runs. At the end of each run the cell was removed from the furnace and quenched by immersing the bottom half in water. After crushing, the slags were analyzed for calcium and total iron by the usual wet methods. The oxygen content was obtained by difference. Specific Conductance: Apparatus and Method. Fig. shows the experimental setup, with the conductivity cell and leads of ingot iron. The standard four-probe method for measuring high conductivities was used. In this, the potential drop across the unknown resistance is compared with the potential drop across a known resistance connected in series, i .e., same current through both resistances. Thus there are both current and potential leads to the center electrode and to the crucible, which acts as th other electrode. Both ac and dc circuits were available for the measurements; they have been described in earlier work performed in this laboratory.4,5 The geometry of the cell was such that the center electrode was equidistant from the bottom and sides of the crucible. This ensured that the current path was the same irrespective of the magnitude of the conductivity of the material in the cell. Cell constant were measured with KC1 or NaCl solutions, which have considerably lower conductivities (0.0013 to 0.25 ohm-' cm) than the slags, and this precaution in design made sure that the determined cell constants applied to the cells with contents of any conductivity. The cell-constant determinations were made with the ac measuring circuit to prevent polarization. The four-probe method eliminates lead resistance but not the resistance of those parts of the center

Jan 1, 1967

By W. A. Tiller, W. C. Johnston

A high-temperature electromagnetic stirrer is described in which heating and stirring are accomplished by independently controlled power sources. The appavatus is suitable lor use at temperatures up to 1700°C in a variety of ambient atmospheres. Some typical examples of the homogenizatimz capabilities of the system are given. THERE are few processes in solidification that are not markedly affected by motion in the melt during freezing. In many instances, the mechanisms are diffusion-controlled, and the transport in the melt may be greatly accelerated by deliberately stirring the melt. In zone-refining, stirring1 assists the removal of rejected impurities from the interface, so the process proceeds at a faster rate. The transition from a planar to a cellular interface is caused by constitutional undercooling in the melt ahead of the interface: and stirring delays its onset. Stirring is valuable for homogenization of melts: and chemical reaction with sluggish kinetics may be accelerated. Finally, it has been observed that grain refinement is related to motion in the melt. Fine grain castings are usually produced by the addition of catalysts to the -melt,' catalysts which are thought to act simply as hetereogeneous nucleation centers. Even here motion is important. Richards and Rostoker 5 applied ultrasonic vibration to a solidifying A1-Cu alloy which had been innoculated with a catalyst and found that the grain diameter fell linearly with the amplitude, the peak acceleration and the power input to the melt from the transducer. Finally, mechanical and electrical stirring alone have been used to generate a fine-grained structure.6,7 Johnston ef a1.' have carried out a series of systematic investigations of grain refinement by electromagnetic stirring in a number of low melting point alloys. They found, for example, that the number of grains per unit volume in Pb-Sn alloys could be increased several orders of magnitude by stirring an undercooled melt at the moment of recalescence. In general, a relation AT .H = constant prevailed for a given grain size, where AT was the undercooling of the melt and H the field strength. In more recent work, deliberate homogeneous nucleation of slightly undercooled melts established that the mechanism of refinement must be one involving crystal fragmentation and subsequent multiplication, rather than a "shower" of nuclei effect.9 It is the purpose of this note to describe a stirring device suitable for use up to 1700°C. At low temperatures mechanical stirring and direct-current methods are feasible, but at high temperatures the problem of a protective atmosphere and of electrode corrosion rules out such procedures. The most convenient method for high temperatures is to use externally generated ac fields for both stirring and heating. With rf induction heating alone, considerable stirring and agitation can be achieved, but in general the penetration of field into the melt is small, and the stirring cannot be controlled independently of the heating. In the present experiments, separate power sources of different frequencies for heating and for stirring were used. A susceptor design was chosen so that the 450 kc rf heating field was completely absorbed in the susceptor. The stirring frequency, 400 cps, hereafter called the af field, was chosen so that a high penetration of the melt proper was achieved. EXPERIMENTAL APPARATUS The apparatus, Fig. 1, consists of a quartz tube and end plates, surrounded by an rf induction coil and six equally spaced af stirring coils, four of which are shown in full and a fifth in section. Each af stirring coil is a transformer of which the secondary is a single-turn water-cooled copper loop and the primary is composed of two 10 amp-117 v Variac cores as shown. These cores are cooled by forced air, as each of the six pairs will carry maximum currents of 15 amp for short periods. Each set of Variac windings are connected in series, but opposite sets are connected in parallel with a three-phase 400 cps 400-v source. By properly phasing the coils in this way, a rotating field is produced. Capacitors C1, C2, and C3 in Fig. 2 are used to match this inductive load to the generator. Fig. 3 shows a cutaway view of the quartz tube. The sample (1 in. diam by 1 in. high) is placed in a tapered alumina crucible. An axial W-26 pct Re thermocouple, enclosed by a protection tube, is provided. The cruci-

Jan 1, 1968

By C. R. Knopp

Gas-oil relative permeability ratio is an important relationship in oil reservoir predictive calculations. A correlation has been developed from 107 gas-flood k/k tests on Venezuelan core samples. The correlating parameter is based on restored-state water saturation tests and' is applicable to both consolidated and poorly consolidated sandstone reservoirs. Data of the correlation show that there are no distinguishah1e differences between the mass-data groupings for the two c1assifications A procedure is recommended for running .sufficient relative. permeability analyses to compute a geometric mean of the sample group. The geometric mean is more representative of the total core, and probably the entire reservoir. For example, while only one in four of the k,,/k,., test curves agreed closely with the resultant correlation of this report, the geometric mean curves of the 16 suites (three samples or more). showed good agreetment ill three cases out of four. INTRODUCTION The gas-oil relative permeability ratio is an important, fundamental relationship in most oil reservoir predictive calculations. Predictive calculations are made to estimate future reservoir production characteristics and ultimate oil recovery. The k1,/k2, relationship is specifically needed to relate the surface gas-oil ratio to the reservoir oil and gas saturation, and to calculate the relative movement of these phases within the reservoir whenever some of the more complex driving mechanisms are present. Laboratory k1/k2, tests are not generally run as a routine analysis. Consequently, k1/k2 data often are not available when needed because the cost of laboratory work could not be justified or the need for such data had not been properly anticipated. When laboratory k1/k2, data are available, they are often very difficult to interpret. For example, wide divergence is sometimes shown in a family of k1,/k1, tests representative of the producing horizon in a single well. With these considerations in mind, a study was made to determine if a relationship might exist between the k1,/k2, curve and some other simple laboratory test criteria. The most probable k1/k2, curve correlation for Venezuela described in this paper is the result of the investigation. The presented correlation defines the most probable gas-flood k,,/k,, curve through the medium of air-water capillary displacement and centrifuge water saturation tests. The laboratory procedures of these tests are. relatively simple, and inexpensive; test data should be. widely available- from routine analysis. DATA AVAILABLE, LABORATORY METHODS The report correlation utilized 107 gas-Hood k1/k2, tests run on sandstone cores of Venezuelan reservoirs. Table 1 is a general tabulation of data pertinent to the tests, while Table 2 summarizes the data. Thetests include 96 from Western Venezuela and 11 from Eastern Venezuela. Eighty-two- of the 107 test samples were sandstones that varied from poorly consolidated to-unconsolidated; 25 were consolidated. The average sample porosity was 26.7 per cent and the average permeability was 1,121 md; these values typify the better sandstone reservoirs of' Venezuela. The Welge gas-flood technique,' based on fundamental Buckley-Leverett frontal displacement theory, was introduced in about 1952 and is widely accepted in the industry. The laboratory procedure is relatively simple, rapid, and can be performed on small core samples. While there have been some minor variations in sample preparation and laboratory procedure in the tests used for the correlation, these tests can be generally summarized as follows. The core sample was first sol vent-extracted and dried. Connate-water saturation was restored by the oil-flushing or evaporation-blow down methods. At the beginning of gas flood the hydrocarbon pore volume was completeiy saturated with the test oil phase. Unsteady-state gas-oil displacement then began with the injection of nitrogen or helium. while the displaced oil and gas phases were incrementally metered at the out-flow face. From the test data, the k,,/k,, curve was calculated by the Welge method.' The individual oil and gas relative permeabilities were also calculated." CORRELATING PROCEDURES In attempting to establish a basis of correlation, we found that broad mid-range sections of 105 of the 107 k,,/k,, test curves could be closely duplicated by a straight line. Only two curves did not show a degree of linearity in this region. Correlation-curve definition parameters were subsequently developed from this observation of consistent mid-range linearity. Possible correlating variables were limited to the physical properties measured on core samples that (1) were widely available as common test data and (2) could be easily and cheaply obtained through future laboratory work. The more obvious possibilities were porosity, permeability and

Jan 1, 1966

By M. H. Yoo

Possible interactions of the perfect dislocations of six slip systems or the c dislocation with the (10i2f (ioii), {ioIi}(ioiZ), {1122}(1123), and {1121}(ii26) type twins in hcp metals have been analyzed from the crystallographic and the energetic points of view. Twenty-six distinct types of possible interactions were identified, and those selected based on crystallographic constraints were examined for their energetic feasibilities by use of the anisotropic energy factors. No long-range elastic interaction exists for a dislocation when its Burgers vector is parallel to the twin interface. Under a suitable applied stress, a screw dislocation can cross slip at the twin interface. For basal mixed dislocations in cadmium and zinc, the interaction with {1012} twins is found to be attractive, indicating that incorporation of these dislocations into the twins is energetically feasible and that twin growth will result. On the other hand, the interaction between both basal and Prism mixed dislocations and the {1012} and (1121) twins is found to be repulsive in Mg, Co, Re, Zr, Ti, Hf, and Be. This indicates that under an applied stress a local stress concentration will develop due to a dislocation pileup at the interface, which may result in a site for either the nucleation of other twins or the formation of a crack, depending on the cleavage strength. WHEN a metal undergoes plastic deformation, a certain configuration of slip dislocations will result in a state of dislocation pileup against an obstacle. The stress concentration thus developed may enhance the process of twin nucleation and also twin growth. Furthermore, once formed and dispersed in the crystal, twins can act as effective barriers against slip dislocations. The degree of such mutual influence or interrelation between slip and twinning is generally known to be pronounced in the case of hcp, metals. It is also known that deformation by twinning occurs more commonly in hexagonal metals than in cubic metals. In fact, under suitable stress states, all hexagonal metals exhibit {1012) <1011> type twinning.&apos; In addition to this common type, deformation by (1151) <1126> type twinning occurs in zirconium, titanium, and rhenium, which show remarkable ductility.&apos; The importance of twinning during general deformation to the ductility of hcp polycrystals has been briefly discussed in recent review works.2&apos;3 The purpose of this paper is to analyze the interaction between slip dislocations and twins in the hcp structure and to discuss the nucleation and growth processes of twinning and the role of twinning in the <"°" noil) o, 1/3[112O] (OOO2) 1/3[1123] Fig. l—-Slip systems in hcp structure. ductility of hexagonal metals. The problem will be discussed from the geometric and the energetic points of view in a manner similar to that of the previous work on zinc.4 Since hcp crystals deform by several slip and twin systems, numerous interactions result as possibilities. The Burgers vectors of six slip systems and the c dislocation shown in Fig. 1 and the four twin systems listed in Table I are considered here. A complete tabulation of the possible interactions is followed by discussion of those that are more likely to occur on the basis of crystallographic constraints and energetic considerations. 1) CRYSTALLOGRAPHY OF TWINNING The crystallographic elements, K1, K2, n1, and n2, for the four compound twin systems are now well established.= A unit cell with the base vectors n1, and n2 is shown in Fig. 2 for each twin system. The unit cell before twinning is shown in solid line, and the corresponding unit cell after twinning is shown in dashed line. Also shown in Fig. 2 are the following crystallographic parameters: S is the plane of shear, d the interspacing of the twin habit planes K1,Ø Iis the acute angle between n1, and n 2, e is a numerical factor, and q is the number of K, lattice planes intersected by 17&apos;. These parameters can be expressed in terms of the axial ratio, y = c/a, as listed in Table 11. The macroscopic shear strain of twinning, s, and the magnitude of a "unit twin dis-l~cation,"4 bt, are also expressed in terms of y and given in Table 11. In Table 11, K1 and q1 are given in both Miller-Bravais and Miller indices. In double lattice structures, shuffling of atoms in addition to a homogeneous shear of the lattice is generally required if the original crystal structure is to be restored after twinning. The extent of current understanding on this problem of atom shuffling is per- Table I. Four Twin Systems in Hcp Structure

Jan 1, 1970

By C. S. Barrett, A. Smigelskas

There have been no publications of the deformation and recrystallization orientations of the metal beryllium, yet pronounced textures would certainly be anticipated since it is close-packed hexagonal in structure. Having an axial ratio approximately that of magnesium, beryllium probably deforms by nearly the same slip and twinning mechanisms that operate in magnesium, and the textures are likely to be similar or but slightly different from the magnesium textures. In the tests reported below this is found to be the case; the textures are found to differ from those of magnesium only in the details of the scatter from the average orientation. This report covers not only samples rolled at room temperature, but some rolled at elevated temperatures. Since magnesium has been suspected by some investigators of altering its crystallo-graphic deformation mechanism at elevated temperatures, it was considered possible that beryllium might do so and alter its textures accordingly. No pronounced alterations were found, however. Unfortunately, the theory of deformation textures is not in a state of development that permits one to deduce the deformation mechanism from a knowledge of the textures, which means that the similarity of textures at different rolling temperatures, reported here, cannot be taken as definite evidence that the deformation mechanism is actually the same at all temperatures. The general similarity of the deformation textures of magnesium and beryllium also extend to the recrystallization textures of the two metals, judging by the pole figures for recrystallized sheet presented in this report. Samples were prepared in the form of composite sheets made up of small pieces stacked in a pile. Each piece was trimmed with scissors so that an edge was parallel to the rolling direction, dipped in paraffin, and assembled into the pack by aligning it under the cross hair of a microscope. As the desired orientation was obtained on each piece it was secured in place by touching with a hot wire to melt the paraffin. A stack of ten or fifteen pieces was built up in this way, then trimmed to the shape of a T; the portion to be X rayed was then etched to the shape of a wire about 0.045 in. diam with 6N HCl. This method of shaping the sample is a modification of that used by Bakarian on magnesium.&apos; The absorption of the rays in the sample was so slight that it caused no difficulty in interpreting the films. Exposures were made with a 0.030 in. diam pinhole, using molybdenum radiation (40 kv, 25 ma, Type A film at 5 cm, 2 to 3 hr exposures). With the recrystallized specimens it was found necessary to oscillate the specimen so as to reduce the spottiness of the lines. A range of oscillation of 5" was SUB- cient to produce reasonably satisfactory patterns, though the quality was somewhat inferior to that of the deformation texture patterns, and only two degrees of intensity were read from the arcs on the films. Typical photo-grams for each of the deformation textures and the recrystallization texture are assembled in Fig 1. The pole figures were plotted in the usual way with the intensity of the various portions of the diffraction rings estimated by eye. Seven to nine films were made of each sample and each was carefully read in plotting the pole figures. Typical series included exposures with the beam normal to the rolling direction and at 11, 26, 41, 56 and 71" to the cross direction, plus two exposures with the beam normal to the cross direction, and at 11 and 79" respectively to the rolling direction. The rolling was in each case considered sufficient to develop the final texture: the reduction by cold rolling was 84 pct (from 0.0045 to 0.0007 in. thickness), following prior hot rolling in longitudinal and transverse directions and recrystallization; the reduction by hot rolling at 800°C was 90 pct (0.010 to 0.001 in.), following similar prior treatment; the reduction by rolling at 350°C was 88 pct (from 0.005 to 0.0006 in.) after similar prior treatment. The recrystallization texture was determined on a sample rolled at 350" to a reduction of 88 pct (0.0165 to 0.002 in.) after similar prior treatment, then mounted between steel strips to keep it flat and annealed at 700" in an atmosphere of argon. Discussion of Results The results of the X ray determinations are assembled in the pole figures of Fig 2, 3, 4 and 5 for rolling at

Jan 1, 1950