Search Documents

By S. Sarac

In this study, graphical and mathematical methods used to determine operating points in single or multiple fan ventilation systems are summarized. The problem is mathematically formulized for parallel connected fans in which analytical solutions are not possible. For n number of parallel connected fans, a non-linear equation system that consists of n number of non-linear equation sis derived. The Newton-Raphson method, which is a numerical analysis method, is adapted to solve this non-linear equation system and the solution steps are given as an algorithm. A computer program based on this algorithm is written and its applicability is proved.

Jan 1, 2000

By Samer Sadek, David I. Smith, Wai-shing Lee, Jeffrey L. Rice, Avelino Alonso

INTRODUCTION East Side Access (ESA) Contract CQ028 is located in the New York City Borough of Queens. The contract involves construction of a 230-meter (760-foot) long open-cut excavation with a permanent deck supporting Amtrak yard tracks over a semi-circular TBM launch wall on the east end, and the 36.5-meter (120-foot) long Northern Blvd. Crossing on the west end. The Northern Boulevard Crossing will be mined under an existing New York City Transit (NYCT) five-track subway tunnel; Northern Boulevard, a heavily traveled five-lane truck route; and an existing NYCT three-track elevated line; connecting to an existing open-cut shaft adjacent to the existing 63rd Street Tunnel bellmouth. When completed, Contract CQ028 will provide access for future Manhattan and Queens tunnel contracts. The footprint of the open-cut was determined by the geometric requirements of the future Plaza Interlocking facility to be constructed within in another future ESA contract. See Figure 1. This paper discusses design risk mitigations for the key elements of the contract, namely the Northern Blvd. Crossing and the semi-circular TBM Launch Wall. PROJECT OVERVIEW The Metropolitan Transportation Authority Capital Construction Company—East Side Access Project for the Long Island Rail Road will provide Long Island commuters with direct access to Manhattan’s East Side via a new rail line between the Harold Interlocking in Queens and Grand Central Terminal in Manhattan. The project connects the unused lower level of the existing tunnel under the East River at 63rd Street to new connecting tunnels in Queens and Manhattan. Contract CQ028 Scope and Construction Schedule This contract consists of the excavation of an open-cut from the east side of Northern Boulevard, through an existing MTA-owned rail yard and into the western limits of Amtrak’s Sunnyside Yard. The contract will connect to a completed open-cut

Jan 1, 2007

By Ramin Motamed, Joseph A. W. Toth

Evaluation of the capacity of large-diameter drilled shafts using current load test methods present challenges when considering the magnitude of loads required to fully mobilize their capacities. Often, these full scale tests do not fully mobilize the capacity through side resistance. Therefore, the need for innovative solutions to extrapolate side resistance and interpret nominal capacity are of key interest. In this study, we evaluate three methodologies for extrapolating unit side resistance based on bi-directional load test data. Fellenius (2001) presented these methods for interpretation of pile capacity using static load tests. Our interpretations are based on the evaluation of 116 load tests. Unit side resistance was calculated and reviewed for each load test and categorized using three criteria of mobilization; (A) full, (B) partial and (C) linear. This study specifically focuses on load tests that showed fully mobilized unit side resistance behavior (Criteria A). The three methodologies were applied assuming Criteria (A) load tests were mobilized to 50% of their measured values. Subsequent comparisons of each extrapolation were then compared against the full measured values for each test and generally showed good agreement. INTRODUCTION It is widely accepted that conducting load tests such as standard top-down tests or bi-directional (i.e. O- cell) tests can help designers understand load-settlement behavior and the nominal resistance of drilled shaft foundations. These load testing methods provide the advantage of confirming design assumptions as well as improving the reliability of the foundation design. The potential cost savings from the application of these methods for mid to large size projects is self-evident. For example, in a recent project in Northern Nevada, an O-cell test on a 6.9 ft diameter, 114.8 ft length drilled shaft imposed an initial cost of $125k to the project, resulting in a 15% reduction on the total foundation cost; equivalent to $1.3 million in overall savings (Pease, 2014). However, the costs of implementing such methods on smaller projects can be prohibitively expensive (Hagerty et al, 2016). Despite the clear advantages of drilled shaft load testing, the current practice is not without limitations. Performing load tests on large-diameter drilled shafts with high capacities is a challenge considering the significant loads required to fully mobilize the capacity of such foundations. In some cases, the feasibility of these tests is impractical because the associated initial cost is not guaranteed to outweigh the final savings. As a result, large scale load tests are sometimes ruled out from the design phase of projects. Furthermore, in the majority of load tests the magnitude of loads applied are specifically selected to not approach failure, so the shafts can be used in the future foundation system (i.e. production shafts). This practice of field testing restricts our knowledge of the true capacity of the drilled shaft at failure; hence the nominal resistance remains unknown.

Jan 1, 2018

By Y. Paul Chugh

NIOSH and the Illinois Clean Coal Institute are funding studies on characterization of coal and quartz dust in Interior Basin mines since 2009. Coal dust characteristics vary significantly and, are vital for the development of the engineering controls. This paper presents wettability characteristics of coal dust with respect to its chemical and physical properties, since wettability is considered to be a primary dust control technique. Particle size distribution, inter-particle interactions during wetting and quartz associations with organic and inorganic matter in coal seams is critical for understanding wetting phenomena. Silica content in the un-wetted fractions was found to be very high during wetting tests. Wetting of quartz may be limited by its association to hydrophobic materials as well as buoyancy forces resulting from particle size characteristics and particle-particle interaction in the wetting agent. Temperature of the wetting solution and effective contact time between dust particles and water droplets are found to be two important variables affecting the wettability. The characterization data obtained from this study can be utilized to develop engineering controls.

Jan 1, 2011

By Michael Cruickshank

Bob Woolsey was born in 1936 in the state of Georgia and grew up to be a man of great integrity, vitality, wisdom and charm, totally neutral on matters of race, gender, and religion. A true Southern Gentleman in every sense of the word. His passing on July 9, 2008, the victim of an automobile collision, left an empty space in the hearts of his family, and his many friends and colleagues throughout the globe. The posthumous award of the Moore Medal of the International Marine Minerals Society, to Dr. J. Robert Woolsey for Excellence in the Development of Marine Minerals, is a well deserved tribute to this man who spent the last 30 years of his professional career heavily involved in research and development of marine minerals on an international basis. He first came to my attention in Burma in 1979 where, as a newly appointed technical advisor to the United Nations Development Program Offshore Exploration for Tin, I had to fill the shoes of an almost legendary figure "Dr. Bob", who accompanied by his wife Maxine had spent the previous two years initiating the program. Bob had planned to completion the construction in Singapore of a unique drilling vessel the RV Sea Drill, a spud anchored, twin-hulled barge, mounted with a Becker Drill, and designed for sampling alluvial tin deposits in the coastal waters of the Mergui Archipelago in the Andaman Sea, off Tenasserim. He had also designed and built, with the help of his side -kick Bruce Jernigan, a barge mounted dressing plant for reducing and concentrating the drill samples. The adventures of Dr. Bob in transporting the equipment to the drilling site in monsoon weather and the transfer of the drill barge from the Malaysian port of Ranong across the strait to Victoria Point in Burma with a mutinous crew will remain in the hearts and minds of his Burmese colleagues for many a long year. On his return to the States he joined, in 1980, the faculty of the University of Mississippi (UM) as assistant Professor of Geology and Geological Engineering. His prior experience in private industry and the United Nations had focused on marine mineral resources and related environmental engineering projects in Africa, South America, the Mediterranean, the South Pacific as well as south east Asia, working with dredges, mining for alluvial tin, gold, diamonds and industrial minerals. He continued to work in the area of marine minerals at UM, making a name for himself as Director of the Mississippi Mineral Resources Institute (MMRI).

Jan 1, 2008

This paper provides an overview of possible approaches for structuring the ventilation systems for mines that will become operational within the next decade. Features addressed in the paper include: aspects of airway design and layout in the absence of centralized vertical return shafts, the impact of using diesel-powered trackless equipment in conjunction with conveyor belts in the development and production phases of the project, and the need to balance increasing electrical power costs against the requirement for reduced capital expenditure. The paper provides brief descriptions of the strategies employed in real-life situations and presents an overview of various operational parameters affecting the design of ventilation systems that will be used as ?platforms? for much deeper mines in the future.

Jan 1, 2007

The environmental impact of solid waste materials is closely linked to their potential to produce a hazardous leachate once deposited in a landfill. This potential is conventionally assessed with simple laboratory batch leach tests, which find more and more frequent application also in the minerals and metals industry. Such tests are intended to help distinguish between high and low risk wastes, but are completely unsuitable to allow quantitative prediction or modelling of the long-term leachate generation potential. In the present approach the leachate generation process is perceived as a combination of bulk convective transport, stagnant zone and inner particle diffusion, as well as reaction kinetic effects. Model equations are formulated accordingly. A modelling frame work, WASTESIM, has been developed at UCT, which allows flexible combination of the model components and simulation of leach scenarios. Quantitative model parameters are obtained from a systematic laboratory study on the waste material in question. The combined assessment and modelling approach is demonstrated with a study on Cr (VI) leaching from a ferro-chromium slag material. Although not straightforward, the approach is particularly useful in determining long-term liabilities in the context of waste disposal sites with considerably more reliability than has previously been possible. Keywords: waste deposits, waste leaching, heap leaching, environmental, risk assessment, Cr (VI), ferro-chromium, slag.

Jan 1, 2000

By M. Bilal Khan

Thermal stress relief by means of a typical heat treatment cycle (660oC for one hr) is compared with the one achieved through vibratory stress relief at resonant and multiple resonant frequencies for the D-406 HSLA material. Our analysis of the data is based on the microhardness profiles measured for the entire length of scales, namely, base metal, heat affected zone (HAZ) and the weld bead itself. The profiles obtained using the two techniques mimic each other, for an equivalent 70% stress relief level. The data are further qualified by impact testing wherein the zone of interest is projected in the retention groove to provide impact by the pendulum striker in the Charpy mode. Higher equivalent energy absorption in the treated specimens confirms the efficacy of the vibratory method. The present work rectifies earlier anomaly where heat treatment has been reported at 310oC for the same material.

Jan 1, 2009

The common theme of these four objectives is declaration. Declaration tells the compiler that an entity exists and also provides the name and nature of the entity. Since everything you create has to be declared, you must know how to declare correctly and be able to make appropriate use of all the declaration tools available to you. This objective recognizes the importance of declaration by requiring you to know everything about Java declarations Write code that declares, constructs, and initializes arrays of any base type using any of the permitted forms both for declaration and for initialization. This objective addresses your understanding of all aspects of arrays. Arrays are the simplest possible data collection and are supported by all modern programming languages. However, Java?s arrays are different from those in other languages, especially C and C++, because they are actually exotic objects. This objective recognizes the importance of being able to make use of all the functionality of arrays. You will be expected to know how to declare, construct, and initialize arrays.

May 1, 2011

By Ingvar Janelid

DURING the last ten years, in the effort to save manpower and costs, methods of drilling and blasting in Sweden have changed and developed in a revolutionary manner. These developments have been accompanied by extensive alterations in methods of tunneling and in mining technique. Since the end of the 1940's there has been a 100 pct change-over in Sweden to the use of tungsten carbide tipped drill steel. Both investigations and practical results have shown clearly that a tungsten carbide chisel bit fastened directly on the drill steel is the most economical for Swedish conditions. This applies to drill steel up to the longest size it is practical to handle. In terms of drilling footage, durability of the drill steel and the tungsten carbide bit is generally the same. In this respect, therefore, a detachable bit offers no advantage over integral steel. Transportation of integral steel to the grinding plant, instead of detachable bits only, involves heavier work, but this is counteracted by placing grinding plants closer together or by grinding at the working place itself. The drilling rate with integral steel is higher, the trouble of changing bits is avoided, and the difficulties which always arise with joints are eliminated. At present steel dimensions are usually 7/8 in. with a shank 41/4 in. long, whereas the international standard shank was formerly 31/4 in. The longer shank renders possible a better guide control of the steel and consequently longer life for the rotation chuck and the water-flushing pipe. After extensive experiments and investigations, agreement has been reached in Sweden on certain series of standards, shown in Table I. Other steel dimensions are, of course, available for special purposes. The standard drill-steel set begins with a 34-mm diam and has a length interval of 2 2/3 ft. On the other hand, for ordinary drifting it has been proved more economical to use greater length intervals on the steel, so only one steel change is required for a 61/2-ft round. Moreover, owing to the relatively close hole spacing necessary in a drift round, it has been possible to reduce the diameters of the tungsten carbide bits. This results in faster and cheaper drilling. As shown by the table, the lengths of drill steels for normal drifting are 33/4 ft and 71/2 ft, with 29 and 28-mm diam bits. During the last few years operators have begun to use 3/4-in. drill steel in place of the 7/8-in. drill steel chiefly employed earlier. This is a valuable development in drilling technique, particularly in view of

Jan 1, 1955

By M. Mabuza

Two Rivers Platinum Mine (TRP) is a 55:45 joint venture between African Rainbow Minerals and Impala Platinum, respectively. TRP is situated on the farm Dwarsrivier 372KT, in the southern sector of the eastern limb of the Bushveld Complex. Dwarsrivier is underlain by rock formations of the Critical Zone (Winterveld norite-anorthosite) and the Main Zone (Winnarshoek norite- anorthosite). Two economically significant PGE-bearing layers namely the Merensky Reef and the UG2 chromitite are found within the upper Critical Zone. These are approximately 140 m vertically apart, separated by a series of barren norites and anorthosites. At Two Rivers Platinum, only the UG2 chromitite layer is currently being mined for PGEs. The UG2 sub-outcrops north/south along the Klein Dwarsrivier river valley with a very gentle dip to the west of 7º?10º. At Two Rivers the UG2 averages about 120 cm in thickness, overlain by a waste pyroxenite parting about 20 cm thick, above which is a leader seam about 20 cm in thickness. The mineable cut consists of the leader seam, the waste pyroxenite parting, the UG2 chromitite layer including 25 cm of pegmatoidal pyroxenite footwall, below the UG2 reef to a minimum of 185 cm trackless mining cut. The mining method is a mechanized bord and pillar layout, which will yield a total of 185 000 tons at full run of mine production from the underground UG2 mine.

Jan 1, 2007

By A. E. Lewis

The emphasis of this paper is on the characterization and testing of the slag produced by a secondary lead refinery. This work forms part of a broader investigation aimed at reducing loss of valuable product from the process as well as minimizing the environmental impact of the process wastes. It was this work that led to a critical examination of the standard waste classification tests. Characterization of the slag was carried out using a number of complementary techniques. In the broader context, the slag characterization aided in identifying process deficiencies and thus was a critical tool in suggesting potential for process optimization. For this study, the slag characterization provided a relatively comprehensive picture of the composition and properties of the slag, which facilitated understanding the behaviour of the slag under batch test conditions. On the basis of quantity of hazardous components alone, the slag is hazardous according to South African Acceptable Risk Limits (ARL). However, when both the quantity and the leach potential of the hazardous components is taken into account, standard waste tests carried out by three independent agencies indicate that the slag should not be classified as hazardous according to local regulations. Also, according to United States Environmental Protection Agency (US EPA) limits, which are independent of the quantity of the waste, the slag would not be classified as hazardous. The standard waste tests used by the independent agencies was the Toxicity Characteristic Leach Procedure (TCLP), a test which was developed by the US EPA to classify hazardous wastes. One of the requirements of this batch test is that it should be quick, simple to carry out and that the results should be reproducible. Previously, the applicability of the TCLP test to mineral processing and metallurgical wastes has been challenged on a number of points. Additional testing of the slag was carried out using both the TCLP and the Synthetic Precipitation Leach Procedure (SPLP) recommended by the American National Mining Association as being more appropriate for mineral processing wastes. The particular physical and chemical characteristics of the secondary lead slag highlighted additional limitations of both the TCLP and SPLP tests as standard laboratory batch procedures. Keywords: environmental protection, secondary lead processing, slag, leach testing, TCLP, SPLP, ARL, hazardous waste, batch tests

Jan 1, 2000

By Jiulong Cheng

Underground coal mining causes overburden deformation and failure, one major form of which is bed separation in the overburden. Surface subsidence can be controlled by injecting grout into the bed separations. For a long time, the grouting results of bed separation can not be validated. This is the problem in the application of this technique. This paper analyzes the conditions leading to bed separation, develops mathematical models for seismic wave fields generated before and after bed separation, and bed separations grouted with different materials, and computes the seismic wave field characteristics using the finite difference method. The results show that the existence of bed separation causes changes in the characteristics of seismic wave field, and that different grouting materials generate different seismic wave field characteristics. Intact strata, bed separation, and bed separation filled with air or water all display distinctive seismic wave field in amplitude and frequency spectra. After mining, the original location that provides strong seismic reflection wave no long exists. It is replaced by a weak and syncline-shaped reflection wave. The area, where the seam wave disappears, is larger than that of the mined area. The location, where a bed separation occurs, generates a set of reflection waves stronger than the normal one. The energy of the reflection waves varies with the materials filling the separations. Bed separations filled with air generate stronger reflection waves than those filled with water. The major frequencies for those filled with air are lower than those filled with water. Therefore, it is possible to determine the property of filling materials by analyzing and comparing the amplitude and frequency spectra of the reflection waves. Case studies of application of seismic method for exploring bed separations and grouting were analyzed. The results show that it is feasible to use seismic technique for exploring bed separations and grouting.

Jan 1, 2006

By P. A. Riveros, W. D. Gould, R. Molnar, D. W. Koren, P. Bédard

This paper reports the results of the field demonstration campaign of a new process for removing and destroying ammonia from mining/ metallurgical effluent solutions. The 50-day campaign was carried out at a uranium plant in Saskatchewan, Canada. The process was developed by adapting and integrating two well established technologies: zeolite adsorption/ elution to extract the ammonia from the effluent stream and to produce a concentrated ammonia eluate; and conversion of the ammonia in the eluate to innocuous nitrogen by applying bacterial nitrification-denitrification (NH3 = > NO3 - => N2). The data show that reasonable target criteria were met, under very challenging operating conditions. Problem areas and possible causes for poor performance are identified. Preliminary and generic cost estimates of the process are also presented.

Jan 1, 2003

By G. R. Morin, A. R. Leggett

"In 2010, closure of the Kidd metallurgical plants along with structural changes to the historical ratios of payable metals led to a review of the operating targets at the Kidd concentrator. Previous operating data indicated that there was potential for significant revenue improvements by lowering the copper concentrate grade. An extended plant trial was carried out in 2011 to quantify the revenue impact of lowering the copper concentrate grade from 27% to 25% Cu, as well as identifying the lower practical grade limit. Analysis of plant trial results indicated that the process change increased net concentrate revenue by $2 M to $3 M per year at current metal prices. Increased revenue was primarily associated with higher silver recovery to the copper concentrate while the marginally improved copper recovery was essentially offset by increased zinc losses and concentrate treatment and freight charges.Details of the plant test work results are discussed in this paper along with the financial analysis of the revenue improvements. Key areas covered are major revenue components of the concentrate contracts, validation of revenue improvements through plant testing and sensitivity of the improvements to market and plant variables.INTRODUCTIONThe Xstrata Copper Kidd concentrator commenced operations in 1966 treating ore from the nearby Kidd volcanogenic massive sulphide deposit in Timmins, Ontario (Thompson, Amsden, & Chapman, 1978). Over the years, up to four separate grinding-flotation divisions were in operation with throughput rates peaking at 4.5 million tonnes per year of ore in the mid 1980’s (Kelebek & Francis, 1998). As the mine production decreased and grinding throughput increased operations were gradually cut back and since 1998 two grinding-flotation divisions have been in operation treating Kidd mine ore. One of the idled divisions has been intermittently used for custom milling operations, most recently the Ni/Cu Montcalm deposit, which was milled from 2004 to 2009. Current budget throughput rates, limited by mine production, are 2.4 million tonnes per year of ore grading 1.7% Cu, 4.3% Zn and 55 g/mt Ag. Concentrate production rates are 150,000 tonnes per year of copper concentrate and 155,000 tonnes per year of zinc concentrate. The Kidd mine is the deepest base metal mine in the world with mining operations down to 9600 ft.In 2010 the copper and zinc plants at the Kidd metallurgical site, which previously treated the concentrate production from the Kidd concentrator, ceased operation due to a variety of economic and market factors. Following the metallurgical plant closures the Kidd concentrator products were shipped off site for treatment. The majority of the copper concentrate is now processed at the Xstrata Copper Horne smelter in Rouyn-Noranda, Quebec with the majority of the zinc concentrate processed at Canadian Electrolytic Zinc Ltd. in Valleyfield, Quebec."

Jan 1, 2013

By B. K. Gorain

"Mining of low grade deposits along with the necessity to design and operate flotation plants with high throughput presents unique metallurgical and environmental challenges that need to be addressed to reduce project risks, improve project economics and to sustain the profitability of operations over the life of a mine.Some of the key challenges include poor recovery of valuables and concentrate quality issues due to complex mineralogy, the need to use poor quality water such as brackish or sea water, reduce environmental impact from the process, integrate flotation with hydrometallurgy to maximize precious metals recovery, escalation of capital and operating costs, use of unproven technology and constant use of larger equipment, high ore variability, worldwide constraints on resource availability and an ever increasing need for reliable metallurgical input to financial models to evaluate economic viability of projects.The need to develop effective solutions to these problems in a short time frame is becoming a key to the success of any new project and for sustaining the profitability of a mining operation. An integrated multi-disciplinary approach to problem solving is crucial with the need for a more lateral thinking along with strategic partnerships and collaboration involving the right players. This paper presents some of the key findings based on experiences from a large number of challenging projects and operations focused on solving complex flotation problems.INTRODUCTIONThere are various challenges to successful development of mineral resources. Most of the ore bodies being developed worldwide are of lower grades requiring high throughput to be economical. Many of these lower grade ore bodies have significant occurrences of deleterious and penalty elements that could render a deposit unworthy of development unless there are technological solutions to process them economically in a sustainable manner with minimal environment impact. Even in a high metal price scenario, the economics for some of these low grade ore deposits is marginal. From a metallurgical perspective, these ore bodies have complex mineralogy and use of any off-the-shelf technology is not always effective. Development of innovative processes are often required, which is expensive, time consuming and sometimes risky.This paper will provide a broader perspective on the steps involved in solving flotation problems for operating plants and for greenfield development projects. In addition, some of the key challenges in flotation of complex low grade ore bodies along with the economic benefits in developing solutions to these problems will be presented."

Jan 1, 2013

An oxide ore heap (80,000 ton assaying 2 per cent copper) and a sulphide ore heap (300,000 ton assaying 1·7 per cent copper) are being leached in series in a closed circuit system. The ore is friable and weatherseasily giving severe percolation problems. These were eased by applying liquors at 235 gal/min to trenches 2 ft wide and 6 ft deep along the full length of the heaps.Cementation recovery was improved from 20 per cent to over 80 per cent by regular intermittent agitation of the iron using a back hoe unit.Liquor pH is controlled by acid addition, and iron content is controlled by a bleed-off set according to predictions made from a pH-Eh diagram drawn for the liquor components. These controls, together with acyclic wetting and draining procedure, have raised production from 6 ton/week to 10 tdn/week of 80 per cent copper.

Jan 1, 1968

Enhancing the Flotability of Gold-Bearing Ores by a Mixture of Collectors

Sep 13, 2010

By Giorgio De Tomi, Ricardo Tichauer

Mineral exploration is a critical step for success in mining. However, small-scale mining often ignores exploration best practices. This paper introduces the Tichauer-DeTomi Matrix, a tool for assessment of geological uncertainty in small-scale mining. This matrix, which measures the level of compliance of exploration programs in small deposits with industry best practices, has been applied to three small mining projects in Brazil: an artisanal gold mine in the Amazon, a small-scale manganese mining venture in the Northeast, and a small manganese deposit in the Southeast. The application of the matrix resulted in indexes that reflect the actual level of maturity of the mineral exploration program in each project. Therefore, the matrix has shown potential to be an effective tool for assessment of the geological uncertainty remaining in small-scale mineral projects, as well as to identify priority exploration activities for reduction of risks associated with the geological uncertainty. As a risk assessment tool, the TichauerDeTomi Matrix may be helpful in promoting investment and sustained development in and around small mines.

By Dave Rose, David G. Meadows, Mike Westendorf

"Copper Mountain’s concentrator was commissioned in May 2011. The circuit consists of a 34’ x 20’ EGL SAG mill, a Raptor 900 pebble crusher and two 24’ x 39’6” ball mills. Each mill is equipped with a 2 x 8500 HP dual pinion drive system. The plant was designed to process 1585 mtph of SAG feed. From startup, the mill struggled to meet the required production rates. Over time, a major initiative that involved blasting and fragmentation, optimization of the SAG mill in terms of discharge grates, ball size and slurry density, and operation of up to three mobile pre-crushing plants resulted in significant increases in throughput. In parallel, a number of modeling tools, including JK SimMet, were run based on plant benchmarking exercises. Samples collected at the mine site during ramp up confirmed the very competent nature of the ore with drop weight - A*b values of less than 24 being recorded on a variety of plant feeds and lithologies. After due consideration including demonstration of proof of concept, a new pre-crushing circuit incorporating an XL2000 cone crusher and associated screening equipment was designed, constructed and commissioned at the site in August 2014. This paper reviews the history of the original circuit design, the various optimization steps taken and impacts, together with the final pre-crushing circuit and net results.IntroductionThe Copper Mountain Mine is located approximately 20 km south of Princeton, British Columbia, Canada (refer to Figure 1). The region has a long history of copper mining dating back to 1923. The Copper Mountain camp occurs in the 'eastern volcanic belt' of the Nicola Group (Monger, 1989). It is an alkali copper-gold deposit in which the volcanic strata are intruded by early Jurassic dykes, sills, irregular plugs and zoned plutons (Woodsworth et al., 1992). The stratified rocks are relatively fresh with slight metamorphism in the local contact regions."

Jan 1, 2016