Search Documents

Laboratory induced polarization measurements were made on representative samples of concentrated sulphide ores from three environments in New South Wales Comparisons were made with the membrane polarization exhibited by an argillaceous sandstone. The sulphide samples showed a strong polarization effect, the magmtude of whIch depended directly on the conductivity of tlIe pore electrolyte.

Jan 1, 1969

By Walter K. Utt

The process of drilling and bolting the roof is currently one of the most dangerous jobs in underground mining, resulting in about 1,000 accidents with injuries each year in the United States. To increase the safety of underground miners, researchers froth the Spokane Research Laboratory of- the National Institute for Occupational Safety and Health are applying neural network technology to rite classification of mine roof strata in terms of relative strength. In this project, the feasibility of using a monitoring system on a roof drill to assess the integrity of a mine roof and warn a roof drill operator when a weak layer is encountered is being studied. Using measurements taken while a layer is being drilled, one can convert the data to suitably scaled features and classify the strength of the layer with a neural network. The feasibility of using a drill monitoring system to estimate the strength of successive layers of rock was demonstrated in the laboratory.

The Effect of Ionic Strength of Plant Water on Valuable Mineral and Gangue Recovery in a Platinum Bearing Ore from the Merensky Reef

Sep 13, 2010

By G. Karahalios

Industrial minerals have always enjoyed an important share in the technological growth of any country in the world. Today, extraction and trading of industrial minerals has expanded, but is also subject to stricter environmental guidelines. This paper presents the current status as well as the growth potential in the exploitation of industrial minerals in the countries of the south eastern European region, i.e. Albania, Bosnia-Herzegovina, Bulgaria, Croatia, F.Y.R.O.M., Greece, Italy, Serbia and Montenegro, Slovenia and Turkey. More specifically, annual production figures per country are presented for1992-1998. These figures are compared to each other and, where applicable, to world production figures. Trading of industrial minerals from these countries to Europe and the world and its effect to the local economies is also evaluated were such data is available.

Jan 1, 2000

By H. D. Mellom

The direction of the optic or "C" axis of a uniaxial metal crystal can be found with the metallurgical polarizing microscope by examining two planes of section on the crystal. Complete orientation of the crystal can be determined if a twin crystal is common to both surfaces of section. Examination of Uniaxial Metals in Polarized Light-Rotation of a uniaxial crystal surface, properly prepared,' shows four extinction positions 90 deg apart, provided that the surface is not close to a basal section. One of these two extinction directions corresponds with the projection of the optic axis on the surface of section. This direction can be found if the 'sign of the rotationr2 for the metal is known. To find the direction of the optic axis, the crystal is rotated on the stage 45 deg from an extinction position. With a crystal of negative sign, to produce extinction the analyser must be rotated towards the optic axial direction and vice versa. All sections, other than basal, of a uniaxial crystal have the same sign of rotation and, since there is no change in sign with wave length, white light can be used for these measurements. U the sign of the rotation is not known the presumed direction of the optic axis can be determined assuming a positive sign. A third section cut normal to the presumed optic axis will show basal extinction if the assumption is correct. It is convenient to use the edge between the two planes of section as a fiducial direction common to both surfaces. The optic axis can be related to this direction. If the above measurements are repeated on the other plane of section and the angle between the two section planes measured, stereographic projection can be used to determine the orientation of the crystal optic axis. Determination of Complete Orientation—The complete orientation of a uniaxial crystal can be determined provided that a twin crystal is common to both surfaces of section, and the twin law is known. The orientation of the twin crystal optic axis can be determined in the same way as for the main crystal

Jan 1, 1962

By S. Tuttle, R. Sisson

"Suncor Energy Inc. has proposed a 2.2 billion dollar expansion to the current oil sands operation, which will more than double the productive capability of the facility. As part of the application for this expansion, a comprehensive closure plan had to be developed and filed.Closure planning includes a systematic evaluation of the area to be developed, the development activities planned, the goals and objectives of the corporation in re-establishing landforms and ecosystems at the same time as running an effective operation. As early as is practical during the mine development, surface contouring is completed, soil is reconstructed, and vegetation, surface drainage and wetlands are re-established. Once active reclamation is complete and vegetation has been re-established, Suncor monitors maturation of landscapes and ecosystems to provide the submission basis for reclamation certification"

Jan 1, 1999

In this paper, the scientific bases of creation of simulation modelling systems of excavator-truck-conveyor complex work are represented. During the simulation modelling process of big mining and transport systems work the strict and full account of an order and sequence of all operations of simulated process is carried out. Step-by-step fixing of mining and transport system elements condition - excavators in loading and unloading points, trucks, road section, unloading points in storage bin, crushers and conveyors is conducted. Work and idle time of system elements are considered. During modelling process the information characterising system work as a whole is collected. It allows us to establish qualitative and quantitative influence of each system element on the final results of its functioning and provides to estimate rationality of a particular organisation variant of mining and transport equipment interaction from technological positions. Simulation results are: economic and technological indicators of mining and transport complex functioning of the period for each subsystem, as well as on the road, the points of loading, unloading and reloading.

Dec 6, 2010

By Faruk Oksuz

The owners of large infrastructure projects are challenged on how to implement sound engineering and construction contracting strategies that address their prime expectations: a quality job, on time and within budget. With the increasing number of large engineering and construction projects worldwide, owners continue to search for alternative contracting strategies to address their risk, quality, sustainability (operability and performance), schedule, and budget concerns. Coupled with the shortage of resources, delays, political pressures, and other obstacles in procurement and negotiation processes, engineers and contractors are also looking for creative ways to optimize contract packaging strategies for efficient and successful project delivery. This paper compiles an array of decision making criteria and suggests a balanced evaluation, ranking and selection strategy in procurement of both engineering and construction services for large tunneling and other infrastructure projects. A number of owners? general preferences and viewpoints are discussed on large tunnel programs encompassing water and wastewater conveyance systems, pump stations and treatment facility upgrades. Contract packaging strategies and project phasing and segmenting alternatives for preliminary engineering, final design, construction management, and actual construction of facilities are featured for several large water and wastewater infrastructure projects. While the selection (and the relevant selection process and criteria) and performance of service providers, whether for engineering or construction, have profound effects on the outcome of any given project, this paper only examines strategies for con-tract packaging. More specifically, the authors evaluated case studies and developed a range of recommendations for packaging of large water and wastewater infrastructure projects with multiple components.

Jan 1, 2008

By Richard H. Bares

This report describes the purpose and application of seventeen statistical and mathematical procedures used in a series of studies made in the project ?A Systems Approach to the Reclamation of Strip-Mined Areas in North Dakota". The objective is to help readers better understand the utility of these procedures.

Jan 1, 1982

Three methods of gold analysis are briefly described highlighting some of the problems and advantages of each. The variation of results between samples and splits and due to method of preparation is illustrated. The mean per cent difference of the fire assay values from the means of sample split values for three cases is 15 per cent.Finally, a comparison of the aqua regia leach atomic absorption spectroscopy (AAS) and fire assay fusion AAS techniques is made.This shows that the mean precision, the ability to obtain the same value, of the methods at 98 per cent confidence is ± 30 per cent and ± 15 per cent respectively. The fire assay fusion AAS method is relatively more accurate than the aqua regia one.

Jan 1, 1984

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures, and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By F. L. Wideman

This paper is one of a series on mining methods being published by the Bureau of Mines. It describes briefly mining practices at the Sunrise iron mine of the Colorado Fuel & Iron Corp., Platte County, Wyo. The Sunrise mine is in the Hartville iron district in east-central Wyoming (fig. 1). The district covers part of the Hartville Mountains, a region of moderate relief in which erosional features have been formed by the dissection of a low plateau. Altitudes vary from 4,300 feet along the North Platte River to 6,000 feet in the uplift. The climate is semiarid, with hot summers and winter temperatures below zero for short periods. Grasses, cacti, yucca, and low desert shrubs grow at lower elevations. Cottonwood and boxelder trees and willows grow along permanent streams; juniper and coniferous trees are confined to the higher elevations.

Jan 1, 1956

By Lulie H. Crump

Salient information on reserves, production, and consumption of fuels and energy by State is summarized in this Bureau of Mines publication. Reserve and production data are shown for each of the fossil fuels (coal, crude oil, natural gas liquids, and natural gas) and for uranium. The consumption data of each of the major consuming sectors (household-commercial, industrial, transportation, electric power, and miscellaneous) are broken down by energy source (coal, petroleum, natural gas, hydropower, and nuclear). In addition, total energy consumption in the Nation in 1973 is compared with consumption in 1972 and 1974 (preliminary data).

Jan 1, 1976

By Peter A. Adcock, Rob Fraser

Interest in monitoring nucleation overpotential in electrometallurgical processes dates back some 40 years or more. Conversely, remarkable progress has been made in recent years on describing in detail the processes involved in the formation of thin films by electrodeposition. The newer body of work underscores a need for greater clarity in speaking about the role of nucleation and in the acquisition and interpretation of nucleation overpotential measurements – the aim of this paper. In electrometallurgy, it is generally desirable to form deposits that remain smooth, compact, and relatively fine-grained while the deposit grows to a thickness on the order of 5-10 mm, about 100 times thicker than technological thin films. Hence, we distinguish two kinds of nucleation that can result in formation of new grains:- (1) initial nucleation (onto the substrate surface) of islands that coalesce into growing deposit, and (2) ongoing nucleation of new grains on the deposit surface long after the substrate has been covered and ceases to have a direct influence. Nucleation overpotential of the first type should be measured on an electrode surface truly representative of a real industrial substrate. The second type requires judicious choice of electrode material – an “ideal foreign substrate”. In general neither the industrial substrate nor native metal to be deposited is suitable for measurement of the second type of nucleation overpotential, because of interference by other processes. For the future, clear terminology is needed to distinguish these two types of nucleation potential. The second is the one for which the type of plot dubbed by Moats and Derrick as an “Adcock plot” and by us as a “Kerby-Adcock plot” was first conceived and correlated with relatively thick zinc electrodeposits. The data of Moats and Derrick showing trends for copper electrodeposition on stainless steel and on copper electrodes are interpreted within this framework.

Jan 1, 2016

By J. L. Bowlby

The heats of combustion of fuels are determined in the laboratory by means of a calorimeter, usually of the oxygen bomb type. A known weight of the fuel is burned in an atmosphere of oxygen under approximately 400 pounds pressure in a heavy metal container-the bomb- and the heat evolved is imparted to a definite quantity of water. From the rise in temperature, measured by means of a Beckmann thermometer, and other data incidental to the determination, the heat value of the sample can be calculated. On paper, the method appears simple indeed, but in practice the determination of the heat of combustion is one of the most difficult of the various coal analyses. This h as led to considerable investigational work in order to obtain formula: whereby calorific values of solid fuels could be calculated from proximate analysis data al one. The proximate analysis of a fuel consists of the determination of moisture, ash, and volatile matter, with fixed carbon by difference. Sulphur determinations properly belong to the ultimate analysis, but in this section of the country, where the sulphur content of the coal is comparatively high, a request for the proximate analysis of a fuel implies the determination of the sulphur as well.

Jan 1, 1929

By J. I. Paige

As part of a continuing effort to develop technology that maximizes mineral and metal recovery from domestic resources, the Bureau of Mines investigated a method to totally utilize copper converter slags without recycling them back through the matte smelting furnace. The research was directed toward (1) recovering the contained copper in converting slags by producing a recyclable copper-iron matte, (2) carbothermically reducing the slags to recover the iron, and (3) producing slag wool from the depleted slags. This report deals with the reduction of three industrial converting slags, containing 2.0 to 7.3 wt-pct Cu, in an 800-kVA electric arc furnace to produce a recyclable copper-iron matte. The addition of sufficient iron pyrite to provide 29 to 113 pct of the stoichiometric sulfur (based on producing 40-pct-Cu matte) produced a recyclable matte (36 to 61 pct Cu) at an energy consumption of 520 to 700 kWh per ton of solid material charged. The expected energy saving for treating molten slag in an electric furnace (5-to 9-MVA range) is about 400 kWh per ton of molten slag treated.

Jan 1, 1982

By M. Dattilo

The U.S. Bureau of Mines has been conducting research on the use of waste-derived zinc as a partial replacement for pure zinc in the electrogalvanizing process. The end product of this process is automotive sheet, which has enhanced cosmetic protection over previously used cold-rolled (CR) steel. In this study, primer-coated specimens of CR and electrogalvanized (EG) steel were subjected to the on-vehicle environment and monitored periodically by electrochemical impedance spectroscopy (EIS) during immersion in 1M NaCI solution. The results of these tests were compared with immersion-only conditions. Scanning electron microscope (SEM) and energy-dispersive X-ray (EDX) techniques were also used to evaluate the corrosion processes and compare them with atmospheric exposure specimens. EIS was found to measure the corrosion associated with on-vehicle exposure, thus providing an excellent screening technique for evaluation of the performance of EG automotive sheet steel.

Jan 1, 1990

By Ioannis K. Kapageridis

The lignite deposits of the Kozani-Ptolemais-Amyntaio basin in western Macedonia (North-West Greece) present a difficult modelling problem. Each deposit consists of several thin lignite layers ranging from a few centimetres to a few tens of centimeters in thickness, and thin intercalated sterile layers of marly limestones, marls, clays, and sands. These layers are practically impossible to model individually due to fast lateral transition of lignite layers to humus clay and vice versa and the lack of reliable and detailed stratigraphic correlation, leading to compositing methods being applied prior to any interpolation and modelling. The complexity of the deposit is further increased by the presence of a number of faults. This paper presents the modelling and estimation procedures applied during the most recent study of the South Western Field ? a new deposit that is considered for development and lignite production over the next years and will support the operation of a new power station in the area. Special focus is given to drillhole database structuring, fault modelling, stratigraphic correlation, mineable lignite intervals compositing, and resource estimation. The use of specialised mine planning software in all stages of modelling and estimation is thoroughly explained.

Oct 1, 2009

By J. L. van Niekerk

The proposed Gautrain Rapid Rail Link (GRRL) will require approximately 15 km of double or twin high-speed rail track tunnels located for the greater part beneath the northern suburbs of Johannesburg, including Houghton, Rosebank and Sandton. During the Environmental Impact Assessment (EIA) it became clear that potential surface vibration above and in the vicinity of the tunnels was a matter of serious concern to the residents of the affected properties and that the impact required assessment. The general method proposed is based on a US Department of Transportation, 1998, publication in which abase vibration curve derived for typical high-speed passenger trains is adjusted for the topological, geological and other features to predict the surface vibration and the associated ground-borne noise. The predictions indicate that some isolated areas might be impacted but that the impact will likely be limited, and it is possible to mitigate the impact using suitable track construction methods and track support systems.

Jan 1, 2004

By W. Petruk

Imaging is a fundamental requirement when characterizing minerals, ores and related products. Images are used for presentation, texture analysis, characterization, image analysis, identification, etc. The image mode that is utilized is dependent upon the application, mineral properties and available instruments. Different instruments produce images that display different features; in order of increasing complexity they are: hand specimens, a non-polarizing microscope, polarizing optical microscope, scanning electron microscope (SEM), low vacuum SEM, microprobe, secondary ion mass spectrometer, staining, cathodoluminescence, tomography and others. Image analysis uses images produced with either an optical microscope or a SEM, but the SEM images are superior in this application.

Jan 1, 2001