Search Documents

By John D. VandeKraats

Yielding rock bolt support systems have been developed to accommodate ground movement in shifting ground such as in coal operations; in creeping ground such as salt, trona, and potash; and in swelling ground associated with some clays. These systems, designed to remain intact despite ground movement, should enhance mine safety and help contain costs in areas where rebolting of rigid non-yielding systems is typically required. Four such systems were tested in straight tensile pulls in the laboratory. They include the Slip Nut System from Dywidag Systems International USA, Inc., Ischebeck's bolt mounted Titan Load Indicator, Rocky Mountain Bolt Company's Yielding Cable Bolt, and a rock bolt installed variation of the yielding steel post developed by RE/SPEC Inc. The first two systems are currently marketed products and the latter two are prototype systems. Each system responds to load and displacement by yielding in a unique manner. All are designed to yield at predetermined loads. A description of each system and its yield function is provided. Each system was tested over its prescribed yield range in a test machine. At least five tests were performed on each system. Each system yielded and continued to provide support according to its design. Each shows promise for ground control use in shifting or creeping rock. This work helps to illustrate the comparative differences in performance between these specialized systems and the applications where they may be most useful.

Jan 1, 1996

By Clyde N. Baker

The paper describes procedures used to predict the settlement performance of drilled shafts constructed under slurry through water bearing deposits to a dense bearing strata, considering both side resistance and end bearing. A full scale instrumented drilled shaft load test on a Jersey City, New Jersey highrise project is used as a case history to compare with prediction.

Jan 1, 1991

Two concentrates from Palabora, in South Africa, containing 0.056-0.068% undesirable Cu and 0.8 or 2.2% Ti, were chlorinated with air:chlorine ratios of 10:1, 15:1 and 20:1 at temperatures between 1 200 and 1 329 K. The resulting volatile chlorides were condensed and the solutions analysed for Cu, Fe and Ti. Recovery of Cu was less than 25% at low temperatures and short reaction times, but at 1 258 K almost all Cu was removed from the magnetite at all ratios of chlorine to air. At higher temperatures, the increased carrying over of iron as FeCl3 could be minimised by decreasing the partial pressure of chlorine. No titanium was detected in the volatile products and the percentage of Cu recovered was independent of Ti concentration in the concentrates, though as a function of Cl2 vol%, more Cu was recovered at 1 200 K from the low-Ti than from the high-Ti concentrate. In a fluidised-bed reactor, Cu recovery was 58-90% and iron carry-over less than 10 ppm

Jun 21, 1905

By T de Wit, S Meyer

The location of seismic events in mines is traditionally calculated based on the arrival times of P- and S-waves for a given velocity model (homogeneous or heterogeneous). This technique is successful when the sources of seismic events are sudden and localised (eg episodes of fracturing in solid rock or dynamic slip along a plane of weakness) and thus the radiated seismic waves have clear arrivals. In massive mining operations such as block caves, strong seismic signals often originate from the movement of loose rocks on the perimeter of the fracture zone. These signals are easily recordable but do not contain easily identifiable direct P- and S-waves, making the estimation of location through traditional methods more complicated. This problem has been approached by using a ‘brightness’ location method that estimates the origin of seismic waves based on travel times of envelopes of seismic energy. This tool is extended to be applicable in a heterogeneous velocity environment that now accounts for the presence of a cave or other strong velocity perturbations. The suggested method is particularly important when caving occurs in low-stress environments (eg close to the surface).CITATION:Meyer, S and de Wit, T, 2016. Location of seismic events associated with caving using brightness method, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 225–236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By G. K. Rogers

The portal, which is the near-horizontal, surface point of entry to an underground excavation, can often be an exceedingly difficult area in terms of ground control. Surface and subsurface failures at portals, as discerned during a study involving over 300 case histories, are unfortunately, common. To aid in the engineering evaluation of portals, the Geomechanics Classification System was appended with discontinuity orientation assessment values and support/excavation guidelines. Also, a design model utilizing RMR predicted rock loads in conjunction with half-dome theory is proposed for the most common type of portal failure. Other pertinent comments and recommendations relating to portal stability are included.

Jan 1, 1989

By R Adamian, F. T. Da Silva, D. H. Gameiro

Schytill and Geldart diagrams were developed for the TiO2-C-Cl2 system at 1 073 and 1 273 K, so as to define the hypothetical relations between particle sizes and chlorine velocity for simultaneous fluidisation of mixtures of anatase concentrate and charcoal for carbochlorination. It was concluded that the operating limits on chlorine gas velocity will be controlled by the behaviour of the reducing agent, mainly because of its lower density. An increase in temperature from 1 073 to 1 273 K will have only a small influence on the fluid-dynamic behaviour of the mixture. For bubble fluidisation, the maximum sizes 0.413-0.478 mm for anatase and 0.529-0.611 mm for charcoal will be adequate. When the particle size distribution is large, fluidisation will be feasible only if conducted in two stages, otherwise the residence time of the small particles in the reactor will be very short. New diagrams will be needed for the gaseous chlorides in the second stage

Jun 21, 1905

By T. A. Kirk

"The Linatex Dewatering System is a compact, low capital and maintenance cost matched set of processing equipment suitable for solids recovery, dewatering and desliming sand-like materials in the range 3/8"" to 325 mesh ( 1). Since its introduction to North America in the early 1970s, various elements of the system have been successfully installed in a variety of applic11tions both in Canada and the U.S.A. Examples are chosen from the coal, fine aggregates, iron ore and industrial minerals industries.II. Elements of the Linatex Solids Recovery System(A) The Linatex Separator (See Fig.I)The Linatex Separator, which is the heart of the system, is a specialized type of hydrocyclone designed to give a self regulating rope discharge product. It has the familiar cyclone geometry of cylindrical and conical section, tangential inlet, apex and vortex finder. The apex is enclosed in a unique patented automatic underflow regulator consisting of a collapsible rubber sleeve, and the overflow line is a siphon-leg, with a controlled air bleed valve. The siphon leg is adjusted so as to balance the internal negative pressure acting as a closing force on the underflow regulator against the mass of slurry pressing down on it from the cone section of the Separator. With correct adjustment the underflow regulator will close drip-tight on a water only feed. As solids accumulate in the apex of the cone the weight of solids counterbalances the vacuum and cat1ses the underflow regulator to open and discharge classified material at a controlled density."

Jan 1, 1978

By M. Verri

[ ]

Jan 1, 2009

Attractive geology does not guarantee mining investment if a region’s policies are bad, according to mining executives surveyed in the Fraser Institute’s seventh Annual Survey of Mining Companies. Companies responsible for a combined US$642.4 million in international exploration (during 2002) rated the policy attractiveness and mineral attractiveness of mining jurisdictions around the world. Jurisdictions like Chile, Australia, Quebec and Nevada bolster their attractive geology with mining-friendly policies, the report said. These locations do well on the overall investment attractiveness index. On the other hand, jurisdictions like British Columbia and Indonesia, each with excellent geology, are hurt by their policies, which have lowered their score.

Jan 1, 2004

By J. L. van Niekerk

The research project reported on represents the first comprehensive attempt to measure the vibration levels of a variety of tools and equipment in the South African mining industry to determine the effect thereof on the health of workers and operators. Although human vibration has been studied extensively internationally only one reference pertaining to the South African mining industry could be found. From studies conducted in Canada and elsewhere it was evident that rock drills do have potentially hazardous levels of vibration. The scope of the research included measurements on a broad spectrum of tools, machines and vehicles used in the South African mining industry. Both hand-arm vibration, where the majority of the vibration enter the body through the hands, and whole body vibration, where the whole body is exposed to vibration through contact by the buttocks or feet, were investigated and measured. More than 700 sets of vibration data measured on 70 machines at 15 mines and workshops were obtained. Data were obtained for at least 24 different types of equipment and machines that were previously judged to have medium to high levels of vibration. All measurements were conducted in accordance with the international standards: ISO 5349, on hand-arm vibration, and ISO 2631-1, for whole body vibration. The equipment with the highest vibration levels in the hand-arm category was: rock drills, both pneumatic and hydraulic; pavement breakers and jackhammers; hand-held compactors; pneumatic wrenches and electrical hammer drills. Of these the rock drills had weighted vibration levels in excess of 20 m/s2. As far as whole body vibration was concerned the highest values were measured on earth-moving equipment. The major conclusion from this study is that the measured vibration levels are sufficiently high to create an enhanced level of risk of vibration-induced disorders in a significant proportion of the operators of hand-held equipment. The most notable examples are hand-held rock drills, pavement breakers, jackhammers and certain selected workshop tools. The results of the study indicate that a comprehensive epidemiological study should be undertaken on present and past workers to determine the prevalence of vibration-induced disorders.

Jan 1, 2000

By M. du Toit

Cromanite?is a new high-strength austenitic stainless steel developed by Columbus Stainless. It contains approximately 19 percent chromium, 10 per cent manganese and 0,5 per cent nitrogen. Cromanite can be welded successfully, but due to the high nitrogen content of the base metal, certain precautions have to be taken to ensure sound welds with the desired combination of properties. Although no matching filler metals are currently available, Cromanite can be welded using a range of commercially available stainless steel welding consumables. Welds produced using E309L, E307, E307Si and E312 filler wires are resistant to hot cracking and the formation of nitrogen-induced porosity, but the hardness, strength, ductility and toughness of the welds are generally inferior to those of the base metal. In applications where full use is made of Cromanite?s high strength, welds with matching strength levels would be required. In wear applications, where Cromanite is used primarily for its work-hardening properties and corrosion resistance, lower strength welds would probably be acceptable. Welds produced using E307 filler metal demonstrate the best combination of properties for use in wear applications. The welds display high rates of work-hardening that would result in increases in hardness and strength when subjected to abrasive or high impact environments.

Jan 1, 1999

Platinum-group minerals (PGM) are recorded from a number of localities along theWaiau River, western Southland, and the south coast of the South Island, New Zealand. At each locality, small amounts of PGMs were recovered as by-products of historical gold mining operations. During the period 1890-1950 an estimated 1000-2000 oz. of æplatinumÆ were recovered from the region, the only area within New Zealand where PGM have been commercially exploited. The PGM suite of southern New Zealand consists of Pt-Fe alloys, IPGE (iridium subgroup, platinum-group elements) alloys, sperrylite (PtAs2), cooperite (PtS) and braggite ((Pt,Pd)S). The composition of Pt-Fe alloy exhibits considerable variation and two compositional populations are recognised. Some Pt-Fe alloy grains are chemically zoned. Iridium is the most abundant IPGE alloy phase and often contains considerable Pt, in contrast to osmium and ruthenium alloys. Cooperite and braggite grains are characterised by extremely low concentrations of Ni.   Exsolution of osmium and iridium from Pt-Fe alloy and Pt-Fe alloy from iridium is observed Several PGM host mineral inclusions which vary from single to poly-phase, display rounded to equant outlines and range in diameter from greater than 100 ¦m to less than 5 ¦m. Olivine and Ni-sulphide inclusions are only present within IPGE alloys. Pt-Fe alloy, cooperite, braggite and sperrylite host Cu-Fe sulphides, a wide variety of PGM, clinopyroxene, amphibole, magnetite and plagioclase within inclusions. Sperrylite also hosts Pd bismuthiotellurides, gold and several potassium-rich silicate phases. Similarities in inclusion phases and mineral chemistry from several localities suggest that the PGM are derived from a single (as yet unidentified), probably calc-alkaline magmatic source. This source is situated somewhere along the margins of the western Southland sedimentary basin where PGM liberated by erosion are transported down the Waiau River and dispersed eastwards along the coast by strong longshore currents.

Jan 1, 1995

By A. Cichowicz

In this study, techniques used to design earthquake-resistant structures are applied to the deep-level mining environment. Earthquake engineers seek to identify the cause of potentially damaging resonance, and design or reinforce structures to reduce these effects. Similar techniques have been used to analyse the dynamic behaviour of the rock mass surrounding a stope in a deep South African gold mine. A three-dimensional seismic array installed in a stope at TauTona Mine (previously Western Deep Levels, East Mine) provided an opportunity to examine the evolution of the wave field close to an underground opening. A set of three-component geophones installed in a borehole above the panel revealed the development of surface waves as wave fronts reached the excavation, and an array of vertical component geophones fixed to the hangingwall provided a two-dimensional map of site effects. While the collected data do not include damaging seismic events, quantitative analysis enabled phenomena which could lead to damage, to be recognized. In the vicinity of the excavation, the energy of the seismic signal is generally transformed from high frequency to low frequency. It was found that seismic events with relatively high corner frequency (150 Hz?200 Hz) usually excite several modes of vibration (30 Hz to 110 Hz), while events with low corner frequency (30 Hz?50 Hz) do not always excite higher modes of vibration in the structure. This implies that the rock mass around the excavation is a complex medium, and should be studied using the multi-degree-of-freedom model. A strong structural effect (due to the excavation shape) was revealed as a low frequency coda wave (at 40 Hz and 60?70 Hz), well developed on the skin of the hangingwall. A strong site effect was revealed by changes in signal properties between hangingwall geophones, exhibiting strong resonances around 160 Hz and in the range 200 Hz to 300 Hz.

Jan 1, 2000

By Charles T. Baroch

RESEARCH strengthened the position of cesium as the preferred material (commonly but erroneously called "fuel") for ionic propulsion engines. Its use as an element of the plasma thermocouple for generating electricity also seemed more likely. Domestic Production.-No domestic ore of cesium and rubidium was produced. San Antonio Chemicals, Inc., San Antonio, Tex., and Maywood Chemical Works, Maywood, N.J., continued to produce cesium and rubidium compounds including carbonate, chromate, hydroxide, nitrate, sulfate, and all four halides. Rocky Mountain Research, Inc., Denver, Colo., began producing various cesium and rubidium salts. American Potash & Chemical Corp., Los Angeles, Calif., offered cesium and rubidium for sale.

Jan 1, 1960

Owing to the increased consumption of sulphuric acid; Australian manufacturers have, from time to time, been seeking for a satisfactory source of sulphur that would make them independent of foreign supplies.Some years ago a considerable amount of acid was obtained from the roasting of Spanish pyrites. This ore, in 1913 or thereabouts, cost 16s. per ton f.o.b. Huelva, and freight to the eastern seaboard of Australia was about 20s. per ton. As the ore contained 48% to 50% of available sulphur, it was costing roughly 9d. or 10d. per unit, and, in addition, the cinder, after roasting, was a product of considerable value to smelters, containing as it did a high percentage of iron suitable for fluxing, and appreciable values in silver and gold.

Jan 1, 1925

By Tracy Brettmann

Equipment ? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2004

By J. Kraemer, A. Preusse

In the federal state of North Rhine Westphalia (Germany) small and medium sized companies are beginning to extract the related gas via old shafts or boreholes and to use it as a source for the production of electricity and heat. More than 100 applications for the separate mining right on mine gas had already been filed by beginning of 2002, since mine gas is treated as a mineral resource under the Federal Mining Law. Meanwhile more than 40 mine gas concessions have been granted and first projects are being developed with encouraging results so far. To enhance the applied techniques and their efficiency Aachen University has formed a research team in this discipline. Scope and goals of this research activities are being presented in this paper. Keywords: extraction mine gas, Renewable Energy Act, Ruhr District.

Jan 1, 2003

By Tracy Brettmann

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2001

By C. O’Hara, S. Roy, K. Swedburg, J. Katchen

"New Gold Inc.’s New Afton concentrator commenced operation in June 2012, producing a copper-gold-silver concentrate. During the first two years of operation, various optimization efforts have improved mill throughput, recoveries and concentrate grade. Daily mill throughput has increased 20% above the design rate. This was achieved through more consistent instantaneous feed rate and size distribution from the mine reclaim stockpile, higher pebble crusher reliability, changes to the SAG and ball mill grinding media sizes, larger SAG grate openings, reduced SAG discharge screen-deck aperture size and an increase in the maximum ball mill power draw limit. Metal recoveries at New Afton are primarily limited by liberation in the coarser size fractions; therefore, improving the grind size at a given mill throughput has been the main means of improving recovery. The average rougher flotation feed F80 size was reduced from 175µm in Q1 2013 to 165µm in Q1 2014, while the average operating mill throughput increased by 25%. Other flotation circuit changes focusing on recovery improvement include the addition of froth crowders to the rougher cells and the use of a stronger frother. The average concentrate grade increased from 22% Cu in Q1 2013 to 25% Cu in Q1 2014. This was achieved by redirecting the flash flotation concentrate stream to the regrind circuit and by the addition of lime to the cleaner circuit.This paper describes the above improvements made at the New Afton mill. The paper describes the objectives, timing and end result of each area of improvement.IntroductionThe New Afton Mine is situated approximately 10km west of Kamloops, British Columbia, 340km north-east of Vancouver. The mine has a moderate climate, access to transportation and electrical infrastructure, nearby fresh water supply, and close proximity to industrial and mining service businesses. The population of Kamloops is around 90,000 with most mine employees living in or around the city."

Jan 1, 2015

By Robert L. Lagace

A whole-mine experiment to assess the practical feasibility and utility of the dedicated-wire technique for overcoming poor trolley carrier phone system performance at a large underground coal mine was designed, performed, and evaluated. The technique involves the use of a single, low-loss, properly terminated and branched auxiliary wire placed in the rail haulageway. This auxiliary dedicated wire allows signals to electromagnetically couple to the trolley wire/rail transmission line, and thereby significantly decrease the overall signal attenuation rate on the trolley wire/rail line. The in-mine dedicated-wire demonstration program and its results, conclusions, and recommendations are described. The dedicated-wire technique is shown to be a valid and practical one for significantly improving carrier phone system performance in coal mines.

Jan 1, 1981