Search Documents

By E. J. Gleim

The importance of "good voltage," especially for direct-current systems in coal mines, is not always fully appreciated. From the practical aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By I. Campbell, P. C. Jones, E. G. Potter, R. P. Taylor

"The Cobalt embayment is a large domain of Paleoproterozoic clastic sedimentary rocks that unconformably overlies the Archean Abitibi greenstone belt. Regionally extensive sills and dikes of Nipissing diabase, emplaced circa 2219 Ma, occur throughout the embayment and are the preferential host to gold-bearing polymetallic vein systems on the Merico-Ethel property, near the northeastern margin of the Cobalt embayment. These gold-bearing, polymetallic veins are predominantly east-west-trending, steeply dipping, discordant calcite- quartz vein systems that formed close to the time of crystallization (within ~15 m.y., based on Pb-Pb ages) of the Nipissing diabase. The ore mineralogy is complex in character, typically comprising sulfides, arsenides, native metals (gold and silver), and specular hematite, preferentially concentrated along the interface between silicate and calcite gangue. A simplified sequence of mineral deposition in the veins is: (1) "Early-stage" pyrite ± chalcopyrite hosted in quartz ± chlorite gangue; (2) "Main-stage" polymetallic (Cu + Co + As + Ag + Au + Bi ± Pb ± Ni ± U) sulfides, arsenides, and native metals hosted in calcite gangue; and (3) "Late-stage" calcite flooding ± galena. Wall-rock alteration in Nipissing diabase is restricted to narrow (<5 cm) haloes of calcite-chloriteepidote- bearing assemblages, whereas a weak alteration halo of specular hematite, calcite, and allanite-epidote has been observed in the surrounding sedimentary rocks. In terms of their age, geology, mineralogy, paragenesis, and morphology, the gold-bearing vein systems at Merico-Ethel closely resemble the silver-sulfarsenide vein deposits of the historic Cobalt and Gowganda mining camps. These observations indicate that the Au-bearing veins are variants of the Ag-vein systems and as such, have a common genesis belt. L’Échancrure de Cobalt est un large domaine de roches sédimentaires clastiques d’âge Paléoprotérozoïque qui reposent en discordance sur la ceinture de roches vertes d’Abitibi d’âge Archéen. La Diabase de Nipissing, mise en place vers 2219 Ma et qui constitue un réseau de sills et de dykes d’importance régionale, est présente dans l’ensemble de l’échancrure et constitue la roche-hôte principale des systèmes de veines aurifères-polymétalliques de la propriété Merico-Ethel, près de la bordure nord-est de l’Échancrure de Cobalt. Ces veines à minéralisation aurifère et polymétallique constituent un système de veines de calcite-quartz sécantes d’orientation principalement est-ouest et à pendage fort qui se sont formées peu de temps après la cristallisation de la Diabase de Nipissing (à ~15 Ma près, d’après les âges Pb-Pb). La minéralogie de la minéralisation est complexe; elle consiste typiquement en sulfures, en arséniures, en métaux natifs (or et argent) et en hématite spéculaire, préférentiellement concentrés à l’interface entre les silicates et la gangue de calcite. La séquence de déposition simplifiée des minéraux dans les veines est : (1) «Stade précoce» pyrite ± chalcopyrite encaissés dans une gangue de quartz ± chlorite; (2) "Stade principal" sulfures polymétalliques (Cu + Co + As + Ag + Au + Bi ± Pb ± Ni ± U), arséniures, et métaux natifs dans une gangue de calcite; et (3) "Stade tardif" calcite massive ± galène. L’altération pénétrative de la Diabase de Nipissing est confinée à des halos étroits (<5 cm) présentant des assemblages marquées par la présence de calcite-chlorite-épidote, tandis qu’un faible halo d’altération en hématite spéculaire, calcite et en allanite-épidote est noté dans les roches sédimentaires environnantes. De par leur âge, leur géologie, leur minéralogie leur paragenèse et leur morphologie, les systèmes de veines aurifères de Merico-Ethel ressemblent beaucoup aux gîtes filoniens d’argent-sulfoarséniures des camps miniers historiques de Cobalt et de Gowganda. Ces observations indiquent que ces veines aurifères constituent une variante des systèmes des veines argentifères et qu’elles partagent"

Jan 1, 2009

By John L. White

Vibratory driver/extractors do more than drive and extract sheet piles. I would say more than sixty percent (60%) of the time, vibratory pile driver/extractors are engaged in work that has nothing to do with sheet piles. This is the main reason I refer to this tool as a "driver/extractor", and omit the word "pile". I have spent the last twenty years applying the technology of the vibratory driver/ extractor to all areas of foundation construction. As you will see, the only limits are humankind&apos;s ingenuity.

Jan 1, 1997

By D Craw, D Falconer

The Morning Star mine is one of numerous historically mined gold-quartz lodes in the Preservation Inlet goldfield of southwest Fiordland. The mine is hosted in Early Ordovician metasedimentary rocks that are composed predominantly of psammitic and pelitic lithologies. These rocks still contain their primary depositional features and are characterised by upper greenschist facies metamorphic grade. &nbsp; The Morning Star mine lies on the eastern limb of a gently south plunging anticline. A bedding parallel fault-vein and an associated network of minor quartz veins hosts mineralisation. The main fault-vein structure strikes N-NW, dips steeply (~60¦) W, has a strike length of ~350 m, a vertical extent of ~170 m and is up to 2 m in thickness. The internal structure of the fault-vein consists of laminated quartz, massive and fibrous quartz, and silicified breccias/cataclasites. Gold is typically coarse grained (~1 - 2 mm) and associated with pyrite, arsenopyrite, chalcopyrite, tetrahedrite and galena. The geometry of the Morning Star mine is similar in form to that of a saddle reef. Gold-quartz lodes in the Preservation Inlet goldfield are comparable in geometry and host rock to their offset equivalents in the Golden Blocks field of NW Nelson.

Jan 1, 2005

By S. Ramachandran, N. J. Grant, T. B. King

MANY investigations of the rate of the sulfur transfer reaction between carbon-saturated iron and blast furnace type slags have been made." It is evident that the reaction is complex, the rate being affected by the presence of elements dissolved in the metal that are readily oxidized and therefore capable of existing in the slag phase. Thus Goldman, Derge, and Philbrook- have shown that carbon, silicon, manganese, and aluminum, in order of increasing effectiveness, accelerate sulfur transfer from iron containing these elements to blast furnace type slags. Quantitative information is still, however, not available on the relation between what have been termed side reactions, such as silicon transfer and CO evolution, and the sulfur transfer reaction itself. In other words, the stoichiometry of the reaction has not been investigated. In the present investigation, the transfer of all reacting elements and the evolution of CO have been measured simultaneously in order to establish the mechanism of the reaction which occurs in practice. Information of this nature cannot be deduced from equilibrium studies. It should be pointed out that in kinetic studies of this type quantitative conclusions are applicable only to the system studied. This restriction should be borne in mind when attempts are made to compare results from different investigations. Apparatus The apparatus used enables slag and metal samples to be taken at frequent intervals and also provides a continuous record of the amount of gas evolved. A sketch of the apparatus is given in Fig. 1. It may be considered in three sections: 1) furnace section, 2) blank volume section, and 3) pressure measuring section. The furnace section is shown in detail in Fig. 2. It consists of two graphite crucibles, C and D, super-

Jan 1, 1957

By Mehmet Guney

At the Armatcuk mine in Turkey, various modifications of sublevel methods have been tried during the last decade in an effort to eliminate gob fires, dangers from roof falls, and surface subsidence, and also to increase extraction efficiency. From the experience thus gained, it was decided that the most likely system to give maximum benefits, considering the existing geological conditions and coa1-seam characteristics, was hydraulic stowing. This paper examines trends in the working techniques of hydraulic stowing and discusses the favorable results and technical problems that the method produced at Armutcuk. The Armutcuk mine, a subsidiary of Eregli Coal Mines (EKI), produces 1300 tons of run-of-mine coal daily from thick (about 10-90 ft) and highly dipping (about 50-90°) coal seams. The coal is highly volatile with good coking properties that make it highly suitable for industrial use. Most of this coal is used in the iron and steel industry at Eregli on the Black Sea coast. Complete recovery of the coal is of vital importance to industrial development and progress. Initial coal extraction was carried out by means of a sublevel mining system modified to accommodate local geological conditions and coal seam characteristics. This method is similar to that employed in metalliferous mines. Several problems arose from the application of the method, one of them being the prevalence of gob fires which caused periodic shutdowns in some sections. To achieve maximum coal extraction with minimum dilution, to eliminate gob fires and surface subsidence, and to reduce fatal accident rates, a decision was taken to change from this method to a hydraulic stowing system. The pres- ence of large deposits of conglomerate and sandstone on the surface contributed to the decision to employ this new method. Although hydraulic stowing practices have been carried out in America and Germany, Upper Silesia may, so far as coal is concerned, be considered the birthplace of the method. Here the process was adapted to thick coal seams on a large scale to reduce dangers from gob fires and damage from surface subsidence. Today, the mining system is not only widely used in the coal mines of France, the Saar, India and Poland, but has also been successfully applied to the iron ore and potassium salt mines in Russia and Germany. LOCATION AND HISTORY The Kandilli-Armutcuk coal field, the most western outcrop of the North Anatolian coal basin, extends for five miles along the Black Sea coast (Fig. 1). The Armutcuk Mine is situated on the southern boundary of the coal field about 40 miles from Zonguldak and about 12 miles from Eregli. The history of coal mining in the North Anatolian coal basin goes back more than a century. Mining commenced on a small scale in the Kandilli-Armutcuk coal field in the late 1880&apos;s, and from this time until nationalization in 1940 the mines were operated by private Turkish and foreign interests. In 1940, Eregli Coal Mines was established to takeover the management of these enterprises. The Armutcuk Mine was developed for the first time in the mid-1940&apos;s. Since then it has been in continuous production and it now produces an annual 440,000-ton run-of-mine output from which 320.000 tons of salable coal is obtained. MINE GEOLOGY The carboniferous inlier of the Kandilli-Armutcuk coal field crops out over an area about three miles long and one mile wide. The major part of the inlier consists of the Namurian formation with only a relatively small area of Westfalian-A visible on the surface (Fig. 2). The Namurian formation, which has no exploitable coal seams in the Armutcuk Mine, consists mostly of arkose sandstones and black shales often having

Jan 1, 1969

By L. J. E. Hofer, J. L. Snyder, J. N. Barn, J. E. Chilton, W. E. Thomas

Various silicone materials have been proposed for use in mining environments. The catalytic methane sensors now employed are poisoned by silicone vapors. Activated charcoal and carbon cloth adsorbents will increase the sensor lifetimes in an environment containing significant silicone vapor concentrations. The results of a study of catalytic methane sensor operation with adsorbent materials in hexamethyldisiloxane-air mixtures are reported. Sampling techniques developed for measuring silicone vapor content of mine atmospheres are described.

By Carnevale Francesco, Bracci Laudiero Alberto, Pampanin Piero

"SummaryIn the Port of Naples a slurry wall has been realized through a sandy layer up to a deep tuff layer using the Cutting Soil Mixing technique.The executed panels have dimensions of 2.8 m x0.65 m in plan and a total length of 25 m. Primary and secondary panels have been executed using the wet to wet technique. During the panels execution the following parameters had been measured: injection pressure, injected volume, verticality. At the end of the works an exploratory campaign has been carried out through boreholes collecting samples for laboratory tests in order to verify the diaphragm thickness and its physical and mechanical properties (i.e. unit weight, unconfined compressive strength).The interpretation of the collected data allowed to verify the efficiency of the method, the volume of slurry loss due to permeation during the panels execution, the quantity of the obtained spoil compared to the volume balance equation, both for the sand and the tuff layer.Eventually, the measured physical and mechanical characteristics of the panels have been correlated to the execution method performed.IntroductionIn the Naples Port area there is a polluted site which has to be hydraulically isolated in order to prevent the pollution of the groundwater that flows from land to the sea through the Port area. A hydraulic cut-off wall has to be realized and particularly a slurry-wall realized using the CSM method had been executed.To date, two stretches have been executed, 140 an 110 m in length respectively, as shown in Figure 1 and Figure 2.After execution, the slurry-walls have been investigated with boreholes. In-situ and laboratory tests on the recovered samples of grout have been carried out; furthermore, the geotechnical parameters of the mix composing the wall have been measured."

Jan 1, 2014

By Paul Doherty

Expansion of the global piling industry has been coupled with significant research efforts investigating the mechanisms controlling pile capacity. Static pile design has transitioned from total stress approaches toward effective stress design, with associated improvements in predicting pile performance. As a result, the available literature is heavily skewed toward static capacity prediction. However, when considering piles offshore, the majority of loading is not static but highly variable and cyclic in nature. This paper outlines the additional factors that require consideration for cyclic pile design, including elevated loading rates, cyclic displacements and capacity degradation. A review of the literature identified a number of cyclic pile testing programs which are collated in this paper. General trends are established through comparison of the tests within the database and the conditions where cyclic loading is most likely to be a concern are identified. In particular, loading conditions which involve full plastic shear reversals are seen to cause the most extreme cyclic damage, with the degraded capacity as low as 31% of the precyclic static capacity. The underlying mechanisms which can result in cyclic damage are explored, with particular attention given to the pore pressure response, radial stresses, shear transfer and particle reorientation.

Jan 1, 2009

By M. H. B. Nasseri

Barre granite?s samples have been tested for fracture toughness under mode I along two different directions with respect to microstructural fabrics were investigated. 3D objects counter algorithm technique is applied on micro CT images to identify physical properties such as crack induced porosity, crack density, generated total surface area and contribution of individual mineral grains within the damaged zone.The result obtained justifies very well the fracture toughness anisotropy in Barre granite, and explains the difference in the structure of the damage zone evolving as a result of test crack interacting with pre-existing microstructural fabrics. The present study has potential application in the fields of rock mass stability, oil reservoir stimulation, rock fragmentation and damage in blasting and emplacement of dykes.

May 1, 2009

By C T. Hollick

Conventional processing of heavy mineral deposits containing radioactive rare earth minerals such as monazite and xenotime may cause industrial hygiene problems through atmospheric dust and contamination of product concentrates. An alternative procedure has been developed in which such minerals are removed from bulk heavy mineral concentrates by flotation with little loss of other economic minerals. With fine ores, recoveries of over 95 per cent have been achieved and with coarse ores over 80 per cent, in both cases at high grade. Several flotation regimes have proven effective. The potential for generation of radioactive dust or product contamination is subsequent processing is correspondingly reduced.

Jan 1, 1990

By Norman O. Lotter, Dominic Fragomeni, Lori J. Kormos, Guy Comeau, Antonio Di Feo

"A performance opportunity was identified for the Raglan concentrator operation by changing the selection of xanthate from Potassium Amyl Xanthate (PAX) to Potassium Isobutyl Xanthate (PIBX). This opportunity was identified by a Statistical Benchmark Survey of the operation and QEMSCAN measurement of these survey samples, in which fine liberated pentlandite was found in the final tailings. This was confirmed by some laboratory scale flotation testwork using High- Confidence Flotation Testing. A statistically designed plant trial was implemented in 2007 to measure and confirm the performance gain. This trial design used on-off switching following a three-month reference distribution of normal operations using PAX. This layout provided both external and internal reference distributions on PAX to be established. These were used to evaluate the internal reference distributions on PIBX. This trial format was deliberately designed so as to block out the effects of autocorrelation in the operations data. In this way, small but significant metal recovery gains may be measured and proven in a plant trial. The paper describes the case study to show that this approach successfully blocks out autocorrelation in time, which is an obstacle in analysing concentrator operations data. The results showed that the PIBX had produced clear and statistically significant recovery gains for Ni, Cu, Pt and Pd. Adjusted for feed and concentrate grades, these recovery gains were: Ni: 1.00, Cu: 0.96, Pt: 5.07 and Pd: 1.90%.INTRODUCTIONConcentrator OperationsMilling and flotation, sometimes accompanied by gravity separation, are well-established unit processes. These have traditionally been used to treat ore that has been mined, producing a lowbulk concentrate containing a high percentage of the paymetal(s) in the ore mined. These concentrates are more economically treated in subsequent beneficiation processes than the ore from which they were produced.This choice of a concentration process results in a significant and variable paymetal loss to the concentrator tailing. This tailing is discarded and disposed of in an impoundment area, and has no immediate business use. This paymetal loss forms the largest loss of paymetal in the entire flowsheet by which refined, or saleable, metal(s) are produced [Cramer, 2001]. The question arises as to whether any particular concentrator is performing at its full potential, and how this answer may be determined. In a concentrator operation, there is always an ongoing performance improvement programme for this reason."

Jan 1, 2009

By Adam Gray, Emery Gray

State-of-the-art seismographs can be employed to assist the blasting engineer in understanding the propagation of vibration waves generated by blasting. Wave traces and frequency plots are used to adjust shot loading and timing, especially around close or near- field structures. Successful close-in blasting vibration monitoring requires careful consideration of the following: Geophone locations Mounting of geophone both on structures and in the ground Differences between ground motion and structural response This presentation will discuss methods used to control and monitor blast-induced ground and structure motions. Case histories are presented to illustrate seismic monitoring used as a tool to control vibrations and guide the blaster in the design process.

Jan 1, 2005

By Stephen Iverson

The National Institute for Occupational Safety and Health (NIOSH) is currently performing research to help mine operators minimize the amount of loose or damaged rock surrounding a blasted opening. Improperly designed blast rounds can result in excessive wall rock damage that may reduce the rock mass competency and increase ground support requirements. Unnecessary blast damage can cause many safety and operational concerns including an increased potential for injury from rock falls and other hazards resulting from sub-optimal blast designs. This paper focuses on the ground control and safety implications of blast damage in underground mines. A reduction in rock quality due to blasting can increase the amount of ground support required. Case study data collected by NIOSH in underground metal mines during standard drill and blast production rounds included blast vibration monitoring, detailed three-dimensional laser scanning of the as-built excavation, and geotechnical mapping of development headings.

Jan 1, 2007

By W. W. Adams

"The ninth yearly National Safety Competition covering the calendar year 1933, conducted by the United States Bureau of Mines, w participated in by 332 mines and quarries situated in 35 States. Enrollment represented as increase of 10 plants over 1932, and one addition was made to the number of States represented.The primary purpose of the United. States Bureau of Mines in conducting the contest is to promote safety in United States mineral industries. This purpose is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive recognition on a national scale for their achievement the purpose is accomplished indirectly through studies by the United States Bureau of Mines of the facts contained in the accident reports the competing companies furnish to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest.The statistics which constitute the basis for determining the winning companies and the relative standing of all companies are prepared uniformly without regard to the States in which the companies operate, or to differences in classes of accidents covered by State laws relating to compensation for injuries resulting, from industrial accidents.Bronze trophies, known as 'Sentinels of Safety', which were provided by The Explosives Engineer magazine to be awarded annually by the Bureau of Mines, were presented to five companies in the contest of 1933, each company having established the best accident-prevention record within one of the five classes into which all companies were divided, namely, anthracite-mining companies, bituminous-coal-mining companies, metal-mining companies, operators of nonmetallic-mineral mines other than coal mines, and quarries or opencut mines. The trophies are awarded for 1 year and are then transferred to the winners of the succeeding year's contest.The trophy for bituincus-coal mines was won by a company in Wyoming. A company in Tennessee won the trophy for metal mining. In the nonmetal-mine group the trophy was again won by a company in New York. A quarry in Michigan won the trophy for the quarry-and-opencut-mine group. The trophy for anthracite mines remains in Pennsylvania, as all anthracite mines in the contest are in that State."

Jul 1, 1934

By S. M. Shelton

Tests employing various ore-dressing methods were made on a manganese wad ore from the W. A. Chinn property in the Batesville-Cushman district of Arkansas in an effort to develop a practicable procedure for the production of ferromanganese-grade concentrates. The ore body occurs as a bed approximately 7 feet thick in the residual clay of the Ferndale limestone formation5/. The crude wad ores are soft aggregates of various oxides of manganese, which are loosely bonded together. Hard lumps of high-grade ore are disseminated throughout the wad. Hausmannite, pyrolusite, and psilomelane are the principal minerals. Some clay is present, but most of the gangue consists of leached fragments of the original siliceous and calcareous rocks in which the manganese occurred. In addition, hydrated oxides of iron, which axe present, also must be considered as gangue. Definite phosphate minerals have not been identified.

Jan 1, 1942

By S. M. Shelton

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well-known that there are largo deposits of low-grade ore in the United States, production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stock piled ore is depleted through inability to obtain adequate supplies from foreign sources. Consequently, a program of laboratory and pilot-plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines. This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series, Report of Investigations 3506, Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent, and C. H. Schack. Other reports will be published as the work progresses.

Jan 1, 1942

Experiments on High Efficiency Separation of Mixed Plastic Wastes by Vortex-Tube Separator

Sep 13, 2010

By A. Sariisik

This study analyses the results of a pilot trial of a newly developed armed-chained stone-cutting machine. The machine was developed in Turkey and trialed at the Kaklik/Kocaba travertine quarries in the Denizli District. An armed-chained cutting machine is an alternative to the diamond wire cutting method more frequently used in the production of natural stone quarry blocks, and increases production efficiency and quality. Since there is no need to collapse the blocks using the armed-chained cutting production process, there is no risk of the block developing cracks. This results in a considerable increase in the efficiency of natural stone block production. The armed-chained cutting machine is easier both to assemble and run when compared to other block cutting methods. This process resulted in the production of a larger number of blocks at a lower cost within the same time frame, particularly in travertine quarries and in all other natural stone quarries. The block efficiency in travertine quarries was calculated as 65?80%using the armed-chained cutting machine, compared with 7?14% using the normal diamond wire cutting method.

Jan 1, 2010

By James Scott

Outline Deposit Overview and Brief History ?Geologic Setting ?Local Geology ?Petrography ?Geochemistry ?Mineralization ?Geochronology ?Conclusions Deposit Overview ?Porphyry Cu-Mo-Au ?Discovered 1957 (BIK Syndicate) ?Various programs, most significant: ?Hecla(1970s) ?Teck(Late 1970s Early 1980s) ?Copper Fox Metals (2005 -Ongoing ?optioned from TeckComincoin 2002) ?Measured and Indicated Resources: ?847Mt grading: ?0.292% Cu ?0.019% Mo ?0.202g/t Au ?1.796g/t Ag ?Total ~ 0.485 % Cu Eq.

May 1, 2006