Search Documents

By Jean R. Garcia, Paulo J. R. Albuquerque, Renato P. Cunha, Osvaldo Freitas Neto

"Abstract Results obtained from in-situ load tests carried out on drilled displacement piles sunk in a porous, lateritic and unsaturated soil deposit, are analyzed in this paper. Three slow-maintained load tests were performed on deep instrumented piles with a diameter of 0.37 m and around 12 m long. The soil deposit consists of a superficial, silty clay “porous” layer 6 m thick, with an average standard penetration blow count (NSPT) of 4 and cone tip resistance and sleeve friction (qc and fs) of 1.5 MPa and 48 kPa, respectively. Under this layer there is a residual stratum 10 m thick, geotechnically consisting of a “porous” clayey silt with an average NSPT of 7 and qc and fs of 2.4 MPa and 202 kPa, respectively. The water table was reached at a depth of 17 m below ground level. The results of the field load tests yielded a maximum pile load (average for the tests) of 1428 kN, which is twice as high as corresponding experimental values from standard bored piles with similar geometric conditions. Exhumation of one of the tested piles was carried out after the test, in order to check integrity and shaft conditions. Numerical finite element analyses, using the commercially available French Code LCPC Cesar®, were performed in order to back-analyze the geotechnical soil parameters for a post execution pile condition. The results permitted a better understanding of the improvement of the subsoil given the intrinsic execution characteristics of this particular pile. It was also possible to note that drilled displacement piles have great potential to become an economically viable solution in tropical soils, given the enhanced behavior of such piles when compared to alternative (cheaper) techniques. In fact, it has several advantages which should make it a key foundation type in the Brazilian market in the future.IntroductionMost buildings in tropical soils use, as the main type of foundation, deep bored or auger type piles. These types of foundations can be performed in various ways, for example with or without soil extraction, with or without bentonite mud and so on. Two main processes maybe formulated: the first execution process is typified by bored pile types, continuous flight auger piles etc., which do not cause excessive soil displacement during excavation. With respect to the second process, one could mention, amongst others, driven piles (precast concrete or steel), Franki piles and drilled displacement piles, which do displace the soil during excavation by pushing the soil laterally around the hole in order to allow either the penetration of the pile or the excavator auger."

Jan 1, 2014

The cost of preparing a feasibility study is notoriously difficult to estimate. Studies for mining projects are typically commenced when an exploration programme has identified a mineable resource and pre-feasibility studies have shown that development of the resource would lead to an economically viable project. Pre-feasibility studies will normally include an estimate of the cost of a formal feasibility study and this estimate would then be firmed up before a commitment is made to proceed with the formal study. Data for preparing the feasibility study cost estimate will be sketchy, geological investigations, metallurgical testwork, and marketing studies may be needed before the scope of the project and hence the scope of the formal study can be finally determined. Before an estimate of the work required and hence of the cost of the feasibility study can be prepared the source of project funds must be decided. Studies for internally funded projects are often less rigorous than those which must be "bankable" and subject to the scrutiny of external financial institutions. This paper sets out suggestions for preparing more accurate cost estimates for feasibility studies by ensuring that all activities are included and shows how a staged approach to preparing such studies can minimise costs and guard against cost overruns. It also provides a case study showing how the estimate compared with actual costs for a recent feasibility study completed by Pancontinental Mining Limited.

Jan 1, 1990

By Carlos F. Perucca, Maria Virginia Ramírez A.

"Chile based SQM S.A., exploits potassium chloride rich salts at the Salar de Atacama, in northern Chile. The process includes the solar evaporation of natural brines existing in the Salar salt bed, followed by conventional flotation to recover Muriate of Potash (MOP) for fertilizer use.This paper describes a structured method developed to aid in understanding the metallurgical response of the solar evaporated salts to conventional flotation. The method uses classical metallurgical data analysis combined with laboratory and plant-scale testing, and rudimentary mineralogical studies.As a result of the study, several changes were made to the flotation circuit which produced an operation that is much more consistent and easier to control, and has an increased recovery. An optimized circuit, currently being financially evaluated, has also been conceptually designed based on the findings of this work.INTRODUCTIONSQM S.A. is the world’s largest producer and distributor of specialty fertilizers, iodine, lithium, as well as a wide array of industrial and specialty chemicals. SQM is a public corporation whose shares are traded in the Santiago and the New York Stock Exchanges.SQM S.A. exploits the mineral rights at the Salar de Atacama in northern Chile. Its production processes involve the solar evaporation of natural brines existing in the Salar salt bed, aimed at the recovery of Potassium, Lithium and Boron compounds."

Jan 1, 2004

By E. R. Bauer

Prolonged exposure to noise can cause permanent damage to the auditory nerve and/or its sensory components, known as noise induced hearing loss (NIHL). It is the most common occupational disease in the United States today. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) is addressing NIHL in the mining industry through several research efforts. This paper presents a general review of NIHL, the status of NIHL in mining, the results of the longwall noise surveys, and a review of the longwall engineering controls research efforts.

Jan 1, 2008

By J. I. Muñoz González

El presente trabajo verifica la utilidad de la incorporación de algoritmos de inteligencia artificial (IA) en cuanto a mejorar los resultados obtenidos en campañas de sondajes de exploración. Tomando la información geológica, geoquímica y geofísica de un proyecto real de exploración, se simularon 3 campañas posteriores y consecutivas, utilizando algoritmos de “boosted regression”. Luego fueron comparados con los resultados reales de los mismos.

May 1, 2008

By Diógenes Albert Gomes

Neste trabalho são apresentados os impactos físicos e mecânicos da reciclagem de insumos refratários compostos por óxidos de magnésio ligado ao carbono, visando à reutilização destes como matéria prima para a confecção de novos tijolos. Os resíduos refratários substituíram, na formulação proposta, 100% massa de MgO utilizado nestes tijolos. O estudo envolveu a confecção dos novos tijolos e a realização de ensaios de caracterização dos tijolos produzidos, através de ensaios físicos. Os resultados mostraram uma porosidade final elevada na condição sem cura, resultando em valores de densidade e resistência inferiores aos dos tijolos produzidos com matérias-primas virgens.

Aug 16, 2017

Quartz, adularia and clay minerals from low-sulfidation epithermal veins at Hishikari were analyzed for their oxygen and hydrogen stable isotope compositions to establish the source of paleohydrothermal waters. Positive correlation between Au-Ag and adularia: quartz ratio, the presence of quartz pseudomorphs of bladed calcite, and Au-bearing smectite and vermiculite is indicative, but not definitive, evidence for the control of boiling on ore mineralization. Oxygen isotope equilibrium temperatures between quartz and adularia are about 220¦C and average homogenization temperatures of fluid inclusions vary between 190 to 210¦C. The calculated d18OH2O and dDH2O values (from quartz, adularia and early smectite) are consistent with paleohydrothermal fluids that were a mixture of magmatic and meteoric waters, or alternatively, the values could derive from heated meteoric water which had undergone isotope exchange during circulation through basement rock. Overall, d18Oqtz values in veins increase toward the north, most likely reflecting palaeo-fluid flow (source).

Jan 1, 2001

The Sams Creek gold deposit near Takaka in northwest Nelson was discovered in 1974 by CRA Exploration (CRAE) geologists. CRAE recognised the potential of the area and subsequently undertook a comprehensive exploration programme of geological mapping, soil and rock-chip sampling, geophysical surveys and diamond drilling. Exploration defined sporadic gold mineralisation contained entirely within a deformed and hydrothermally altered, peralkaline granite porphyry dyke with a seven kilometre strike length, and up to 60 m thickness. Rock chip samples indicated extensive and economically significant gold grades over approximately one kilometre strike of the dyke at Main Zone prospect. CRAE completed 30 diamond drill holes at this prospect and defined a limited resource. Oceana Gold Limited recommenced active exploration at the Sams Creek Project in late 2002, focusing on improving the geological understanding and known resource at Main Zone. Completion of 1041 m diamond drilling successfully increased the estimated resource to 10.7 Mt @ 2.12 g/t Au containing 729 000 oz at a 0.7 g/t cut off. A further campaign of 1560 m diamond drilling was undertaken in 2003 - 2004 to extend the resource and test the continuity of high grade mineralised zones. Deeper intersections of the porphyry dyke indicated geometrical complexity and grade variability similar to that observed at shallow levels. Recent research suggests that Sams Creek can be geologically classified as a variant of intrusion-related gold systems, and therefore comparable to some other, very large gold deposits. However, due to the rugged terrain and dyke geometry, surface drilling is reaching the limits of viability at Main Zone. If infill drilling continues to be successful then an underground decline may be developed to facilitate further exploration. Potential also exists along strike, where other significant gold anomalies are known but largely untested by drilling.

Jan 1, 2004

By SDN Wessels, WA Naismith

On 16 July 2004, at 07:10 a collapse of about 1.8 million m3 (about 4 ½ million tonnes) took place on the north wall on Nchanga Open Pit This collapse was the result of a developing instability that was first identified when the benches in this area were exposed during September 2002. The NOP Geotechnical and Survey Departments closely monitored the development of the failure. Control measures were implemented to reduce risk to men and equipment. These measures were continually improved and adjusted in reaction to observations and changing conditions. The purpose of this paper is to describe in detail the monitoring results that were obtained both by traditional methods and the novel Slope Stability Radar System (SSR). Difficulties encountered in establishing critical deformation levels and deformation rates that can be used to predict the onset of collapse are described. Details of the monitoring and control measures, which led to the successful completion of mining in the area, are also described in this paper.

Jan 1, 2005

By M Thierry Bernart

The software QUALITIR is a software developed by CNSIDCI, framework on five research and experimentation years. This conceived tool by specialists for professionals is a decision aided design tool concerning mining. It makes party the rare software regrouping the different themes approached by the profession namely, the general idea of blast design, blasting sequences, the fragmentation as well as the study of vibrations. Henceforth it is by the intermediary of such tools that performances in term of profitability, security or impact on the environment will be able to be realized.

Jan 1, 1997

By P. Kolodziejczyk

Mining seismicity can be harmful both under and on the surface. ? Tremors are not totally damaging, but destructive to buildings and infrastructure, especially in highly urbanized regions, such as Upper Silesia in Poland ? Destroy the social appreciation, trust and support for mining industry ? To prevent or reduce these effects, engineers and scientists develop methods allowing prediction of ground shaking intensity near buildings and various losses that can result from it Evaluation and prediction of mining tremor?s damaging influence on buildings is usually solved with two steps: ? Estimation of local ground shaking intensity (based on known attenuation relation) and classification into one of several predefined intensity intervals ? Apply supposed relation between the shaking intensity interval and qualitatively defined damaging effects to express predicted effects This makes a mixed quantitative/qualitative procedure, difficult to analyze or optimize

Aug 1, 2013

By Rebecca Hardy

The escalating demand for coal, in addition to the steady depletion of reserves, has produced increasingly difficult mining conditions for coal mining companies within the United States, resulting in mining above or below previously mined areas. The safe and productive extraction of coal in a multiple seam environment requires specific design technology for effective mine planning. Presently, one of the most useful design approaches for multiple-seam feasibility analysis is using numerical modeling techniques. Therefore, numerical modeling programs LaModel 2.1 and Lam2D were used to determine the feasibility of mining the Herrin (No. 6) coal seam over an existing room-and-pillar mine in the Springfield (No. 5) coal seam in the Illinois Basin.

Jan 1, 2006

The La Colosa, Colombia porphyry gold deposit is currently in the pre-feasibility stage. This large deposit has many types of gold mineralization: native gold, electrum, and tellurides. These variations in the gold mineralization lead to variability in the gold recovery. The final process flowsheet may include gravity concentration with cyanide leaching. Metallurgical testwork is utilized to identify the zones of ore that may be problematic to recover. To help select the samples that represent the fluctuating variability zones, geometallurgical models are constructed using mineralogy and geology data. These zones are then wireframed and compared to the geological and structural models for spatial correlation. Samples for the variability testwork will be selected from these different zones to identify and analyse the effect the different gold mineralization types have on the recovery. By using geometallurgy to aid in the sample selection for metallurgical testwork, the variability in the ore body can be understood and constrained to aid in process optimization.

Feb 27, 2013

The mineral industry is an important element in the human environment and in varying degrees contributes to the general standard of living throughout most of the world, both by supplying the basic materials required for heavy industry, transportation, construction, scientific equipment, and many labour saving tools and also by its contribution to the international economy.When projecting population growth and per capita resource utilization against a finite amount of nonrenewable mineral resources, it is apparent that at some future time, if the established trend continues, the supply of industrial minerals will progressively become exhausted according to their relative scarcity and world demand.In one way or another all of nature's mineral resources are used in the sel'vice of man. Some of the products of their manufacture are essential to the survival and further development of our civilization, others are luxuries, desirable but not essential. Marine vessels are essential to maintain a flow of resollrces around the world, and as trade increases the size of the fleet will grow and the quantities of metals needed will be greater.The commodities they transport, may be used in an inefficient or extravagant manner causing unnecessary depletion which may adversely affect the activities of future generations. An example that comes readily to mind is fuel oil, the international transport of which uses a vast tanker fleet. When refined, large quantities of motor spirit are used in motor vehicles. The U.S.A. alone uses 70 billion gallons annually in the 90,000,000 automobiles in use.Much of this is used in private cars-of which there is one for every 2'3 people-for transport between home and city. Well organized community transport would serve the same purpose, conserve a scarce commodity, take some of the stress out of livingdriving in a major city can hardly be considered a relaxing experience-and minimize the problem of atmospheric pollution.Whilst man has demonstrated his great versatility...

Jan 1, 1973

By A Asadov, D Nair

This paper discusses the determination of the percentage of crystalline material in a natural silica deposit which would be considered harmful to health (<10 ¦m). A sample of the natural silica material was recovered and split into a number of subsamples. Samples were sieved using a conventional dry sieve to remove material >300 ¦m before testing. Particle size analyses of the fine fraction showed 75 per cent of the material was below 10 ¦m. Initially XRD and XPS were run on the samples to determine the minerals and composition of the sample. The XRD revealed strong quartz peaks and smaller tridymite peaks with a high amorphous background. The XPS indicated traces of iron, titanium and carbon with dominant silicon and oxygen peaks. The structure of the sample was investigated using the SEM. It was apparent that there were a number of larger quartz crystals (>30 ¦m) with a mix of amorphous and crystalline in the finer fraction. It was also observed that amorphous material was attached to the surface of the crystals. In order to determine the percentage of crystalline quartz a known amount of quartz was added to the sample incrementally. On each addition an XRD scan was performed and the area under the peaks recorded. Back analysis of these peaks with an assumed percentage of crystalline material in the original sample gave a crystalline content of 30 per cent. The quantity at the respirable fraction was estimated to be 18.7 per cent.

Jan 1, 2003

By P G. Self, M D. Raven, R A. Eggleton

Investigation of an abandoned quarry near Rowland Flat in South Australia identified asbestiform antigorite as the fibrous serpentine mineral mined during the 1940s to 1978 for filler applications, not amphibole asbestos or chrysotile as reported in earlier investigations. Scanning and transmission electron microscopy (SEM and TEM) and selected area electron diffraction (SAED) of individual fibres were used to confirm the identification. Chrysotile is widely regarded as the only asbestos mineral in the serpentine group. Further work was done therefore, on the geology and mineralogy of the occurrence, and the health implications were reviewed. A zone of antigorite alteration, with associated talc, is traceable for 750 m along strike of recrystallised dolomitic siltstone within Woolshed Flat Shale of Neoproterozoic age. The antigorite formed, in part, by replacement of prismatic crystals of probable tremolitic amphibole. The deposit is proximal to the Williamstown Fault and the serpentine-talc alteration is possibly due to fluids expelled along the fault during late-stage deformation in the Early Palaeozoic Delamerian Orogeny. The antigorite comprises white to pale green bundles of lath-shaped fibres that occur either as randomly- arranged equant patches after amphibole or as cross-fibre veins, both intimately mixed with calcite. Highly fibrous product was mined from the weathered zone where calcite was leached during weathering. Gentle grinding releases fibres with a high aspect ratio (>10:1) that show a wide range of fibre thickness, including a significant proportion of fibres <0.25 ¦m width. Toxicological studies on fibrous antigorite from Poland and Italy indicate that the carcinogenic potential of this form of serpentine is similar to amphibole asbestos. X-ray diffraction (XRD) and fourier-transform infrared (FTIR) techniques readily distinguish antigorite from chrysotile. Determination of asbestiform habit and confirmation of antigorite mineralogy is most reliably done using electron microscopy, preferably with SAED capability.

Jan 1, 2008

By G Sparrow

The Murray Basin is being heralded as the next major mineral sands province in Australia. Already exploration programs have delineated extensive commercial deposits and several companies are progressing with plans to produce zircon, rutile and ilmenite in the Basin. As these deposits are developed consideration will need to be given to several key issues of the Murray Darling Basin; the availability of fresh water and management of salinity in the area being two of them. In this paper ideas being developed in CSIRO that link the processing of mineral sands with the salinity problem in the Basin are presented. The proposal presented here is to process saline water to produce industrial minerals with large volume applications and to produce value-added products from the mineral sands in the Basin using reagents produced from the saline waters. Processes to produce titania pigment and zirconia consume chlorine, caustic soda, soda ash and hydrochloric acid, all derivatives of salt (sodium chloride). There may be a good economic incentive if these processing plants were located in the close vicinity of each other.

Jan 1, 2001

By W. A. Wood, H. M. Bendler

Cylindrical fatigue specimens of OFHC* copper were subjected to alternating torsion while under axial tension. The superimposed tension strongly influenced the fatigue life of the specimens as well as causing characteristic changes in the structure of the fissures that form and develop throughout the life of the specimen. A further effect of the superimposed tension is a continuous extension of the specimen throughout its life in a manner formally similar to creep at elevated temperatures. RECENTLY, studies of the structural changes leading to fracture of metals by fatigue have been made by a technique which reveals, in section, the lattice distortion arising from slip movements inside the metal and the disturbances built up by these slip movements at the metal surface.1'2 According to this approach, fatigue develops as follows: a) fine slip movements concentrate in bands, producing little strain-hardening and thus permitting abnormal totals of plastic strain before fracture and, therefore, abnormal amounts of lattice distortion along each slip band; b) both forward and backward slip movements occur in each band which, according to their distribution across the band, may build up surface disturbances that include sharp notches; c) these notches early in the life of a specimen penetrate the distorted slip zones and transform them into deep, fine fissures; d) the fissures on continued cycling locally saturate the metal and cause local collapse in the form of a microcrack. Thus, the significant consequence of fatigue or cyclic

Jan 1, 1962

By R. H. Atkinson, R. N. Rhoda

An improved technique has been developed for the deoxidation of palladium with aluminum which is especially suitable for use in making small castings with an induction-melting and casting machine. The effect of various crucible linings on the efficiency of the residual deoxidizer and accompanying oxide film in protecting palladium against oxidation during remelting also has been examined; the preferred crucible lining consists of zirconia cement. THE objective of this work was to develop a simple method of deoxidizing induction-melted palladium which would be suitable for use by manufacturers of jewelry and other small castings. In a common method of deoxidizing torch-melted palladium a piece of aluminum foil is dropped on the surface of the molten metal. If a film is present, which is usually the case, it must first be removed by oxidizing the molten metal thoroughly because it would interfere with the entry of the aluminum into the melt. Removal of the film is probably facilitated by a mild fluxing action of the silica crucibles which are used for torch-melting. However, removal of an alumina film from molten palladium in the crucibles normally used for induction melting is a much slower process and it became necessary to modify the de-oxidation procedure. In the modified procedure the charge is simply melted and the desired amount of aluminum, crimped to one end of a tungsten wire, is plunged through the film into the palladium and the wire immediately withdrawn. The trace of tungsten which dissolves along with the aluminum can be avoided, if considered objectionable, by using a palladium wire. In view of the persistence of the alumina film under the conditions of induction-melting it also was decided to ascertain the efficiency of this film in protecting palladium against oxidation during repeated remelting and casting. Melting Equipment and Materials The equipment used for melting and casting consisted of an Ecco GC:6, 6 to 8-kva high-frequency converter and an Ecco M34B centrifugal casting machine. This unit is being increasingly used for making jewelry and dental castings and it also has been found useful in making exploratory melts of a variety of nickel alloys, for which purpose it is well suited on account of its speed of melting and economy of material. A description of the machine and its operation will be published elsewhere.' A common palladium jewelry alloy, 95.5 palladi-um-4.5 ruthenium (referred to as "palladium" in the trade), was selected for the deoxidation tests. It was available as melting stock which had been melted in air to free it from oxidizable impurities, and also as clean scrap from previous melts which had been deoxidized with aluminum. The latter was thought to be typical of clean "palladium" scrap to be found in a manufacturing jeweler's establishment and it is also similar to one brand of "casting palladium." By the same token, the oxidized melting stock corresponds to "casting palladium" after the latter has been melted and thoroughly oxidized: Pure aluminum wire (99.9 pet), 0.032 in. diam; 1 in. = 0.036 g. Scrap tungsten wire, 0.014 to 0.020 in. diam. Argon, commercial water-pumped; 99.9 pet pure Experimental Procedure Samples of about 50 to 75 g of the palladium alloy were melted in a crucible lined with a proprietary refractory alumina cement. Some charges were melted in air, others in argon. The oxidized melting stock was melted and solidified a number of times in order to remove as much oxygen as possible before deoxidizing, but this treatment was unnecessary in the case of scrap. In either case the metal was deoxidized with aluminum (0.01 to 0.05 pet) by the

Jan 1, 1959

The need for the hydraulic transportation of coal in the New South Wales coal industry, both from the coal face to the surface and from the coal mine to the consumer or the port for export, is explained. Details of research projects currently in'progress and involving the hydraulic transportation of New South Wales coals are given together with information on the hydraulic transportation of coal in the United States of America.The potential of hydraulic transportation as a viable alternative to the proposed expansion and upgrading of the New South Wales railway system to meet the projected New South Wales coal production to the year 2000 is described.

Jan 1, 1980