Search Documents

No paper available.

Jan 1, 1996

By V. Bondarenko

The forecasting of floating earth inrush into the working is to a great extent connected with the investigation of the rock mass stressed-deformed state around the working. The aim of such investigations is to estimate the carrier ability of the protective layer (which is stabilized by the physico-chemical mode of fixing) and to determine it's thickness, which is to be sufficient to present the floating earth inrush into the working. We consider the protective layer to have exhausted it's carrier ability if the rocks of this layer reached the overlimit phase of deformation and it's greater part (section), which adjoins the working. is destroyed up to the limit of the remaining strength. So, the aim of investigations is to determine the size of the rocks inelastic deformation zone in the roof of the working. It is necessary to take into account the presence of water saturated seam in the roof and the overlimit characteristics of the rocks, their ability to lower the carrier capacity up to the level of the remaining strength.

Jan 1, 1996

By J. R. Koehler

Although two-entry yield pillar-based gate roads supported by wooden cribs have been commonly used throughout longwalling in the Wasatch PlateadRoan Cliffs coalfield of central Utah, a three-entry yield-abutment gate road configuration was recently trialed in the Hiawatha Seam at the Genwal Resources (GRI) Crandall Canyon No. 1 Mine, near Huntington, UT. Pillar, entry, and cable bolt performance were monitored through second panel mining using a fairly extensive array of geomechanical instruments installed over a span of four crosscuts. Ground pressure and entry closure measurements confirmed that the 9.1-m-wide (30-ft) yield pillar was partially shielded from first panel longwall loads by the 36.6-m-wide (120-ft) abutment pillar, and consequently, experienced only minor yielding until the approach of the second panel face. Complete yielding of the 9. I-m-wide (30-ft) pillar occurred when the second panel was approximately 6.1 m (20 ft) inby the instrumentation site. Average cable bolt loads and differential roof sag remained low through second panel mining and tailgate entry ground conditions were excellent; however, very high ground pressures in the abutment and yield pillars, and second panel rib strongly suggest a high potential for coal bumps utilizing this gate road configuration at mining cover depths in excess of 396 to 457 m (1300 to 1500 ft). This conclusion is supported by the suspected occurrence of small coal bumps along the abutment pillar ribs, observed indirectly as fresh debris in the middle entry just behind the second face. This paper presents a case history developed from the geotechnical measurements and on-site observations of this unique application of a yield-abutment gate road configuration and cable support system in the Hiawatha Seam.

Jan 1, 1996

By Djk Arentsen

A new technique to drive tubular piles by impact hammer inside the pile has confirmed a dramatic reduction of noise and the opportunity to save steel. Also a reduction in driving time and a higher bearing capacity has been observed during a test program of this technique. As part of the so-called "Down-the-hole" driving technique, a wave equation analysis has been developed to calculate driveability and pile stress. The main feature of the new "Down-the-hole" technique is the development of a patented device allowing uncoupled penetration of pile tip and pile shaft, which makes it possible to drive both closed or open end piles and reduce the stress level induced in the pile wall. During a test program, a number of instrumented piles were driven and compared with traditional driving of the same pile with the same hammer on top (also instrumented). Also the stresses and performances were compared with precalculations. This paper, explains the technique and presents the test and noise results, in comparison with traditional top-pile-driving. The "Down-the-hole" driving technique is an interesting alternative for special applications where traditional pile driving requires a large wall thickness or in areas where noise is a hot item.

Jan 1, 1996

By Uwe Hess

For the Danish landworks for the coming fixed link between Denmark and Sweden across the Øresund the focus has been on the environmental aspects of the construction and operation of the facilities. This paper describes how the environmental objectives pertaining to the project have influenced the design and construction of one of the major elements of the Danish landworks, i.e. the tunnel in Sydhavnsgade and under Sydhavn Station. The chosen construction methods for the construction pit bracing and the groundwater lowering will be described along with the observed effects on the environment as shown by simulated or measured values for noise impact, settlements, pumped groundwater and extension of the drawdown cone.

Jan 1, 1996

By S. Narasimha Rao

Significant amounts of lateral load may act on pile foundations supporting structures such as transmission line towers, tall structures, bridge abutments, offshore platforms, quay wails, harbour structures and anchorages for water front structures. There were several theoretical and experimental studies conducted on laterally loaded piles in clays to determine ultimate lateral capacity and deflections under working loads. Under a lateral load, a pile deflects in the direction of load application and the soil in front of the pile offers resistance to this movement. The ultimate lateral resistance of a pile can be estimated considering the statics of the pile for a known distribution of soil resistance with depth. In this paper, considering the contributions from both lateral shear drag and frontal passive earth pressure, a method has been proposed to estimate the ultimate lateral capacity of rigid piles in clays. The lateral shear drag has been estimated in terms of adhesion and shape factor. A few load tests were conducted on model piles subjected to lateral loading and these experimental values are used in verifying the proposed method. The reported results obtained from both model tests and field tests were used in support of the predictions made. In all the cases, there is a good agreement between the predicted and measured capacities.

Jan 1, 1996

Blasthole deviation is a frequent, well documented and undesirable occurrence in mining operations. It is caused by the drill string mechanics, operating variables and the interaction between the drill bit and the rock mass characteristics. It is composed of three distinct components: collaring or marking error, alignment error and trajectory deviation. This study has focussed on the dependence of trajectory or natural deviation on the geological features of the rock mass being drilled.

Jan 1, 1996

The Main Seam occurs in two 'pods', termed North and South, separated by an east-west oriented 'want' zone (most probably a palaeo-channel). The seam on either side of the 'want' area reaches thicknesses of over 30 metres but the North Main Seam adjacent to the 'want' zone has been split into multiple seams of 10 to 15 m thickness. Rock types in the inter-burden of this area are characterised by inter-bedded sandstones and carbonaceous mudstones varying in thickness from 0.5 to 5 m. In the South Main Seam, an area of un-split coal exists and is characterised by few inorganic partings. Overburden in this area varies geographically from relatively thick mudstones in the south and east part of the coal deposit to inter-bedded sandstones and carbonaceous mudstones adjacent to the 'want' area. The sandstone/mudstone overburden probably represents a splay or splay-channel complex emanating from the larger 'want' area palaeo-channel. Modelling lithological variability is of use because it is one of the factors used in predicting cavability and roof support system design. The coal in both the north and south deposits were found to exhibit highly predictable quality and breakage parameters in relation to the coal geometry. Although ash yield and sulphur are mostly low and not variable, volatile matter and thus fixed carbon, varied in relation to seam thickness. In general, volatile matter (dat) decreased and moisture increased with decreasing seam thickness whereas moisture increased with decreasing seam thickness. In addition to these parameters it was found that the energy needed to crush the coal was lowest at the top and bottom of the seam and, on a whole seam basis, decreased with seam thickness. All of these parameters were found to vary in relation to the vitrain band content of the coal which itself was controlled by seam geometry. These parameters can therefore be modelled and inputted into mining plans and quality control operations.

Jan 1, 1996

By A. M. Raichur

Flocculation of fine coal is usually accomplished with the addition of commercially available organic flocculants. Recently it has been shown that biopolymers derived from microorganisms can be used to flocculate coal. The biopolymers flocculate coal efficiently and render the coal surface hydrophobic. The increase in hydrophobicity can be utilized either to separate the coal flocs from mineral matter. It can also be used for reducing the moisture content of fine coal. In this regard, flocculation and settling tests of fine coal with biopolymers and synthetic flocculants was undertaken and the results are discussed here. Also, a transport model was developed for the time-dependent settling tests for fine coal.

Jan 1, 1996

By V. M. Shick

For practical purposes of the use of information resources in the field of geomechanics and mine surveying with accepted mining technology in mines, the authors have developed the packaged software programs of the survey-geomechanical information system with database objects of mine field. This system enables to execute the graphical representation of workings layout in preset scale, axonometric projection, the zones of higher ground pressure: program packages for calculations of rock pressure manifestations and for selection of suitable support facilities for the permanent, development and active workings and vertical shafts based on the information resources of the State Research Institute of Mining Geomechanics & Mine Surveying (VNIMI). The program packages are applied at coal mines in Russia and in Kazakhstan. The profitable operation of coal mines can be reached only by the combined optimal engineering decisions in mine working's laying-out and their reliability and safety at the stages of their designing and exploitation, and with minimal harm of the environment as well. This problem is being complicated by the fact that today the mining-practicing engineers and designers are ordinarily facing the problem " of an information barrier", when the complexity of controlling systems exceeds the potentialities of traditional management of production practice. Coal mine is a typical representative of complicated systems, because the information about geological structure, physicomechanical properties and stress-strain state of rock mass are of fragmentary character and insufficiently reliable. A mine has a developed network of interrelated workings, by the way, some of them are productive ones being subjected to control to a certain extent, and some of them are abandoned ones being noncontrollable and hazardous in rushes of water, gas, pulp and fire. The ground pressure forces cause the disintegration of rock mass growing with depth. The progress of mining operations constantly changes the geomechanical situation forming the zones of bearing pressure, stress relieving, coal falling, as well as it leads to the pulp movement on the earth surface, breaks the ground water flow, causes deformations and changes in stability of buildings, constructions and natural objects on the earth surface. One should take into account the existence of hazardous zones within the mine field, i.e. the zones of elevated ground pressure, geological dislocations and those ones under natural water reservoirs, ponds, etc. Major coal seams are prone to rock bursts, sudden outbursts, bleeding, endogenic fire. It is obvious, that in practice it is extremely difficult to account for the mentioned above factors in their interrelation.

Jan 1, 1996

Continuing with the effort of providing new and more effective exploration methods to the mining industry, where direct methods (drilling, cross-cutting, etc.) are not applicable, either for logistical or environmental reasons or because they are costly and sometimes ineffective, we present here a new seismic technique based on full wave recording of 3-D channel waves generated within the coal seam across a longwall. In the past two years we reported the application on In-Seam High Resolution Seismic Reflection (ISHRSR) and In-Seam Seismic Tomography (ISST) to map non-coal inclusions that disrupt the coal seam continuity. In the present paper we present a 3-D In-Seam Seismic Tomography (3-DTSST) method using 3-D channel waves recorded by three component high resolution geophones. The method allows to distinguish longitudinal and transversal components of the channel waves, similar to the spheroidal and toroidal modes for the free oscillations of the earth. The recording of these waves allows a more complete analysis of the free modal vibrations of channel waves, permitting a more complete inversion of the structure of the coal seam through which they travel. The full wave analysis provides additional insights of the detailed coal structure for larger, distances than for the ones previously reported using the one dimensional method. The refinement of the inversion software is also a contribution towards the better definition of the coal seam geometry and structures disturbing them such as sandstone channels, sandstone rolls, partings, mine voids, faults, fractures, etc. The method is illustrated with three case studies where subsequent mining revealed the virtues and limitations. The first example deals with the problem of mapping mine works in one side of a longwall panel which geometry is well known, to verify its applicability to map old mine works. The second example deals with a sandstone body that partially scoured the coal seam withing a longwall panel. The third shows an application of the method to map roof conditions in a longwall panel where this problem critically affected production scheduling and costs

Jan 1, 1996

By F. W. Petersen

The Conference Minerals & Materials '96 was held in Somerset West, South Africa, from 31st July to 2nd August, 1996. It was organized by the Universities of Stellenbosch and Cape Town, the Cape Technikon, and the Western Cape Branch of The South African institute of Mining and Metallurgy (SAIMM). The three-day Conference was attended by 180 delegates, representing countries such as Australia, South Africa, United Kingdom, Finland, Sweden, Germany, Poland, Zambia, and Zimbabwe. The programme and associated exhibition were well organized, and each of the delegates received two volumes of proceedings containing the 77 papers presented at the Conference.

Jan 1, 1996

By Thomas M. Barczak

With the development of the shield support, the primary requirement for successful ground control in longwall mining is to provide stable gate road and bleeder entries. Wood cribbing has been the dominant form of secondary support. However, the cost and limited availability of timber, along with the poor performance of softwood crib supports, has forced western U.S. mines to explore the utilization of other support systems. The recent success of cable bolts has engendered much interest from western operators. Several innovative freestanding support systems have been developed recently including: (1) "The Can"' support by Burrell Mining Products International, Inc., (2) Hercules and Link-N-Lock wood cribs and Propsetter by Strata Products (USA) Inc., (3) Variable Yielding Crib and Power Crib supports by Mountainland Support Systems, (4) the Confined Core Crib developed by Southern Utah Fuels Corporation; and (5) the MEGA prop by MBK Hydraulik. This paper assesses design considerations and compares the performance and application of these alternative secondary support systems.

Jan 1, 1996

By G. R. Dasari

New Austrian Tunnelling Method (NATM) has been analysed by Finite Element method in two and three dimensions by Strain Dependant Modified Cam Clay (SDMCC) Model. The effects of construction sequence, stiffness of shotcrete and time dependency of shotcrete on surface settlement magnitude due to the NATM have been studied. Settlements obtained in 2D analysis, as expected, found to be more than the observations. The surface settlements obtained in 3D analysis found to be about 3 times less than equivalent plane strain analysis. This is due to mobilisation of soil strength around the tunnel face and soil-tunnel lining interaction. About 40% settlements occurred due to excavation of face at the monitor section and 60% after the excavation crossed monitor the section.

Jan 1, 1996

By Ho E

Analyses of several nickel mattes from around the world show a significant variation in their copper content. Typically, matte contains an alloy, heazlewoodite and a copper sulphide phase. The various commercial methods of processing these mattes are reviewed and some of the fundamental factors which determine the choice of leaching system are discussed. Electrochemical studies on pure heazlewoodite and millerite in sulphate and chloride media are compared which show that nickel sulphides react via a series of nickel deficient sulphides and exhibit passivation as nickel is removed. Differences in the electrochemical behaviour of nickel sulphides in chloride media are attributed to greater crystallinity of sulphur and less formation of'NiS2. The electrochemistry of mattes differs because of the presence of alloy and copper. Copper in the matte modifies the potential for alloy dissolution and the rate of anodic dissolution of nickel. At elevated temperatures, Cu(II) in solution exchanges with NiS and completes the leaching of nickel at relatively low potentials without significant oxidation of sulphur to sulphate. It is concluded that there are fundamental advantages to leaching nickel matte in chloride media using Cu(II)/Clz as the oxidant.

Jan 1, 1996

By Stuart Brashear, Robert Brush, Ben Cook

In early 1993, the Piney River quarry owned and operated by the Blue Ridge Stone Corporation of W W? Boxley received a series of complaints from the owners of a 130 year-old historic farmhouse that had been converted into a bed and breakfast establishment. Since the distance from the quarry to the farmhouse was substantial, a unique method of seismic data acquisition was utilized to determine if perceived blast effects were caused by air blast or low amplitude, low frequency ground vibration.

Jan 1, 1996

By J. R. Donald

Surface and interfacial phenomena play a significant role in refractory performance. For example, the wettability of the refractory material with slag, matte, and metal influences infiltration and interfacial reactions. Yet, very little fundamental information regarding the surface properties of refractory materials and slag is available. Thus, in the present work, the sessile drop technique incorporating a high temperature furnace equipped with X-ray fluorescope was employed to investigate the surface and interfacial phenomena of fayalite-type slags on solid alumina at 1200?C. The iron to silica (Fe/SiO,) ratios employed were 1.4 and 2.0, and the oxygen potentials used were log p02 =-11 and log p02=-9 atmospheres. The contact angle between the fayalite-type slags and the alumina were determined to be relatively low, at about 16.9 to 19.6 degrees under the experimental conditions. The surface tension of fayalite slag (Fe/SiO2=1.4) at an oxygen potential of log -11 was 0.298, which agreed with the work of previous researchers. The surface tension of the fayalite was observed to increase with time. The spinel FeAl2O4. was determined to be the product of the interfacial reaction, and 8.8 to 15.8 mass percent alumina was dissolved into the slag after 40 minutes.

Jan 1, 1996

By Dennis R. Dolinar

Controlling coal mine roofs subjected to high-horizontal stress conditions has always been difficult and uncertain. Traditional supports such as wooden cribs and posts, concrete donut cribs, and standing supports collapse and fail when the roof and floor move horizontally as mining progresses. The former U.S. Bureau of Mines (USBM) (currently the U.S. Department of Energy (DOE)), in cooperation with Western Fuels-Utah, Incorporated, conducted research to provide an alternative for traditional secondary support systems in a 3-entry gate road system subjected to high horizontal movements. The support system used in several other coal mine operations, consisted of internal high-strength galvanized resin-grouted cable supports. The system virtually eliminates the necessity for external crib, timber, or concrete supports. The support system consisted of 2.4 m (8 ft) full-column resin grouted bolts and 4.8 m (16 ft) long cable supports installed in conjunction with wire mesh and "Monster-Mats." Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during first and second panel extractions. Additionally, cable trusses were installed on the longwall headgate to protect the coal conveyance system from roof and pillar falls created by the formation of cutters and gutters. The test results indicated that the designed support system successfully maintained the roof during the extraction of two longwall panels and dramatically reduced the cost of secondary support. This paper describes the theory of high-horizontal roof movements, the advantages of vertical cable supports and cable trusses, and presents the roof and cable measurements made to assess the support performance during longwall retreat mining.

Jan 1, 1996

By L. R. Stace

Arguably, one of the most significant technological breakthroughs that had been experienced during the period when British Coal was the major coalmine operating company in the UK, the use of rockbolts as principal support in underground roadways brought with it the need to re-assess the technical knowledge, management controls and legislative frameworks associated with the support of mine workings. Following a major roof fall in a roadway supported principally using rockbolts in which fatalities occurred, the process of the design of rockbolted support and the systems and procedures that had been put in place to control its use in the UK were further reviewed. The paper discusses the outcome of these reviews, and how the incident initiated a major new interest in strata control research in the UK against the background of the fragmentation of the ownership of the mines following the sale of the former British Coal assets at the end of 1994, together with the proposed introduction of new strata control legislation in 1996.

Jan 1, 1996

Rhyolitic rocks are volumetrically significant in the eastern part of the Coromandel gold province, yet deposits hosted by rhyolite (Kapowai, Broken Hills, Neavesville, Wharekirauponga and Waihi Beach) are generally low grade and subeconomic, especially compared with andesite-hosted deposits. In contrast, rhyolitic volcanic centres in Nevada host a number of economically significant epithermal gold deposits such as Round Mountain, Sleeper and Bullfrog. The Nevada deposits are associated with 27-20 Ma continental arc volcanics dominated by ignimbrites (eg Round Mountain), or younger 17-9 Ma bimodal rhyolite-basalt volcanism related to extensional basin-and-range tectonics (eg Sleeper). The Round Mountain deposit is localised on a caldera boundary fault and the mineralisation was deposited soon after eruption of the host rhyodacitic ignimbrite. In other Nevada deposits, hydrothermal systems are linked to the closing stages of flow-dome complexes and mineralisation is localised along normal faults associated with extensional basin-and-range tectonism. The style and composition of the mineralisation is similar in both the Coromandel and Nevada deposits and consists of sheeted and stockwork quartz veins, containing electrum as the main ore mineral and only minor sulphides (mainly pyrite) Likewise, the vein minerals were deposited from low salinity hydrothermal fluids in the temperature range of 200-270¦C. Both the Neavesville and Round Mountain deposits are geochemically anomalous in molybdenum. The deep oxidation of the Nevada gold deposits, dry climate and low level of competing land uses combine to make it economic to mine and process very low grade ore (0.2 - 2.0 g/t Au) by heap-leaching with cyanide solutions in most areas of Nevada. Although extensive low grade gold mineralisation is known at deposits such as Wharekirauponga and Neavesville, it is sub-economic because of shallow oxidation and land use conditions that are unfavourable for open pit mining and heap leaching.

Jan 1, 1996