Search Documents

The gold concentration profiles which develop inside the activated carbon particles during the adsorption process were measured, so as to obtain additional direct proof of intra-particle mass transfer rate-control and to determine how individual carbon particles in a population vary in their gold uptake behaviour. The observed gold concentration profiles inside the activated carbon particles were typical of situations where an intra-particle mass transfer mechanism is rate-controlling. Gold di-cyanide penetrated the carbon particles with a wave-like front until it was uniformly distributed throughout the particle. This corresponds with the profiles predicted by the film and surface diffusion model. However, the rate with which gold di-cyanide was transported inside the individual carbon particles varied within the population of carbon particles. This variation was characterized by a lognormal distribution in surface diffusivity. Because the estimated variances of these surface diffusivity distributions were small, the dynamic adsorption behaviour of the carbons used in the present study did not deviate significantly from that predicted by a model based on film mass transfer and a single surface diffusivity. Van Deventer (1984, 1985 and 1986a) reported data that could not be adequately described by a model based on film mass transfer and a single surface diffusivity. In this study a model based on film mass transfer and a wide lognormal distribution of surface diffusivity values was applied to his data. It was shown that a population of carbon particles with a wide distribution in surface diffusivity values could offer an alternative explanation to the mechanism proposed by Van Deventer which was based on film mass transfer, with partitioning of the carbon into micro- and macropores with surface diffusion in the macropores and slow mass transfer into the micropores.

Jan 1, 1997

By Murray Gamble

A new type of groundwater cutoff wall has been developed at the University of Waterloo. The Waterloo Barrier? is a steel sheet piling system that incorporates a sealable cavity at each interlocking joint. In order to prevent leakage through the joints, the sealable cavity is flushed clean and injected with sealant after the installation of the piling. The installation and sealing procedures of the Waterloo Barrier? system allow for a high degree of quality control resulting in a very low permeability cutoff wall. Based upon field installations, the bulk wall hydraulic conductivity of the Waterloo Barrier? ranges from 10-8 to 10-10 cm/sec. Recent case histories are presented in which Waterloo Barrier? vertical cutoff walls have been used to prevent the off-site migration of contaminated groundwater or soil gases. In some instances, the Waterloo Barrier? system was used in combinations of applications such as preventing the migration of contaminants, redirecting the flow of groundwater, providing structural shoring for soil excavation and aiding in site de-watering processes.

Jan 1, 1997

By William C. Cooley

SUMMARY A review is presented of the state of development of high pressure water jet equipment and of large impact hammers for rock tunneling. Information from the U.S.S.R. is based on published literature and three personal visits. Applicable papers which were presented at the International Symposium on Jet Cutting Technology in Coventry, England in April 1972 are reviewed. Data are presented on continuous jet systems, pulsed water cannons, and hydraulic-powered impact hammers with respect to the specific energy of rock breakage and potential application in tunneling machines. INTRODUCTION It has been estimated that the cost of underground excavation during the period 1970-1979 in 15 countries of the Organization for Economic Cooperation and Development will be over $54 billion, an increase of 104% over the period 1960-1969. It is expected that 55% of the tunneling construction will occur in hard rock (Ref. 1). Present tunneling machines are generally limited to soft and medium-hard rock. When used in hard rock, the cost of replacing mechanical cutter bits is high. Therefore there is a need for improved rock fracture methods which can be applied economically in tunneling machines for hard rock. Water jets and mechanical hammers are two

Jan 1, 1997

By Madan B. Karkee

The understanding and the development of sound theoretical basis concerning the pile foundations has been phenomenal during the past few decades, considering the thousands of years the piles have evidently been in use. The importance of the quality assurance and the need for verification of load bearing capacity is being further reinforced rather than undermined by these developments. This is evidenced by significant developments made in the pile load test technology in recent decades, making it possible to make judicious selection of a test method, or a package of test methods, suitable for a given situation. The selection depends on the objective of carrying out the test and the reliability desired. Presently, the possible selection ranges from dynamic to static methods. The extent of dynamic effect in a test can be reckoned based on a dimensionless parameter defined as the 'relative duration'. Examples of different load tests are given for illustration of the different methods currently in use.

Jan 1, 1997

Myths and misconceptions regarding cyanide in the mining industry are common. This is not surprising, given the other uses to which cyanide is, and has been put. Unfortunately, the economic benefits, largely due to the introduction of cyanide in towns such as Waihi are often unrecognized. In the current "green" environment, the New Zealand mining industry faces constant scrutiny and challenge. The use of cyanide in hard rock mining is one area which can stir the emotions of the public.   Cyanide can be transported, stored, used and disposed of in a safe manner. The modem mining industry has an excellent record regarding the safety and environmental issues relating to cyanide. Many of the fears relating to cyanide in the mining industry have proven to be unfounded. It is important that this reputation is maintained. This is possible given proactive and ongoing management of cyanide issues.

Jan 1, 1997

By Hill KC, Foster DA

Methods for ore reserve estimation are classified. The amount of information needed to asses ore reserves is analysed. Reference is made to gold sampling. Consideration is given to nugget effects and ore reserve estimation procedures where they are significant. Computer methods are discussed

Jan 1, 1997

By Allan Sylvester

Construction of the Shot Tower Metro Station in Baltimore, Maryland was performed in two phases. In the first phase, a contractor was retained to excavate the station in order to construct twin tunnels from the Shot Tower Station to the John Hopkins Station. The retention system for this 70' deep excavation consisted of a Soldier Pile in Tremie Concrete (SPTC) wall supported by cross-lot bracing. In phase two, The Clark Construction Group, Inc. was retained to construct the station interior structure, two entrances, two station ancillary shaft structures and the track work for the station and tunnel. The excavation for the construction of the two entrances adjacent to the 70' deep station SPTC wall had to proceed prior to completion of the station structure due to the tight construction schedule. A system of overlapping secant piles was specified as a vertical support of excavation element for the West Entrance. The secant piles would have provided a watertight, rigid support to resist the load from the SPTC wall constructed in phase one. A watertight system was required in order to minimize the settlement of adjacent buildings supported on wood piles. Clark Construction was concerned with the constructability, cost and performance of the specified secant piles and looked for other innovative methods of providing a watertight and rigid system. Substitution of a reinforced slurry wall in lieu of the secant piles was cost prohibitive due to the additional cost of concrete placed under tremie. Clark, being familiar with cement-bentonite cut-off walls and slurry wall construction procedures, proposed the construction of a PSHG wall, in lieu of the secant piles. The PSHG wall construction consisted of trenching 30" wide by 20' long by 60' deep panels under a self-hardening slurry. Once the excavation for a panel was completed, a 60' deep prefabricated soldier beam and lagging panel was placed in the slurry. The slurry design mix then self-hardened within the cure time, allowing excavation for the structure to proceed This paper will discuss the design, details and construction methods used on the PSHG wall and will compare the advantages of the PSHG system to conventional support systems.

Jan 1, 1997

By Francis J. Arland

The installation of augered cast-in-place (ACIP) piles requires careful quality control to assure a successful pile installation. Unlike steel, pre-stressed concrete or other types of driven piles, which are shop fabricated, delivered to the site and typically driven to a minimum tip resistance, augered cast-in-place piles are installed to a pre-determined tip elevation or to a refusal criteria. The structural section of the ACIP pile is constructed during pile installation and cannot be inspected prior to installation. Therefore, a carefully administered quality control program is essential to a pile foundation that will meet or exceed design requirements. This requires an experienced team consisting of the Geotechnical Engineer, Contractor and Inspector. The focus of this paper is to discuss the responsibilities and duties of the ACIP piling Inspector. Qualifications of the Inspector The qualifications of the inspector are related to the complexity and difficulty of the proposed project. Ideally, the Inspector should be an individual with a degree in civil engineering with special emphasis in geotechnical engineering. A properly trained technician with geotechnical engineering experience working under the direct supervision of a geotechnical engineer may be able to provide competent inspection on some projects. It is important that the Inspector have a good understanding of subsurface and ground water conditions and how they will affect pile installation. The Inspector must understand ACIP pile installation procedures and be able to communicate with the Contractor, Structural and Geotechnical Engineers; and maintain a detailed pile record for each installed pile.

Jan 1, 1997

By Robert W. Bergwall

The $58,000,000.00 Columbia Heights Metro Station project (Section E3-a) forms a part of the Washington Metropolitan Area Transit Authority's (WMATA) Greenbelt Route - Green Line subway system. The Greenbelt route is one often segments that make up WMATA's subway system. Construction of the "cut and cover" reinforced concrete station includes 600 linear feet of an underground center platform, two ancillary service areas totaling 466 linear feet, two surface entrances, and vent shafts (See Figure No. 1). Station subgrade is approximately 60 feet below existing grade. The project can be divided into five main areas: 1. North Service Rooms and Passageway; 2. West Entrance and West Passageway; 3. East Entrance; 4. Center Platform; 5. South Service Rooms. Station dimensions are approximately 1068 feet long by 64 feet wide. Construction commenced at the site in January of 1995 and is expected to be completed by December of 1999. Franki Northwest Company, Crofton, Maryland, was awarded a subcontract by general contractor Blake Construction Company, Washington, D.C, to install the support of excavation and temporary decking systems. Franki's scope of work included the installation of 490 drilled soldier piles plus two elevator shafts totaling 29,700 linear feet of drilling; 1,150 tons of steel decking covered by 37,000. square feet of precast concrete deck planks; 120,000. square feet of timber lagging; 2,500. tons of struts and wales; and temporary support of underground utilities. In conjunction with Franki's work, Bencor Corporation of America, Dallas, Texas, constructed parallel, 600 foot long slurry walls which serve as permanent walls for the center platform portion of the station.

Jan 1, 1997

By Elwyn King, Donald J. Dodds

"...Unfortunately, the research activities in soil mechanics had one undesirable psychological effect. They diverted the attention of many investigators and teachers from the manifold limitations imposed by nature on the application of mathematics to problems in earthwork engineering. As a consequence, more and more emphasis has been placed on refinements in sampling and testing and on those very few problems that can be solved with accuracy. Yet accurate solutions can be obtained only if the soil strata are practically homogeneous and continuous...." This statement about soil mechanics was made by Karl Terzaghi, thirty years ago and applies to a greater degree today to the infant science of rock mechanics. More uncontrolled variables are added to the already many existing in soil mechanics. Variables, such as Macro-discontinuity and in situ stress levels. In no other field of engineering are the problems as site oriented. Presently this site dependance demands the investigator or rock mechanics engineer to get his hands dirty rooting in the muck of a tunnel floor trying to properly install or readout test apparatus in a comprehensive site investigation. This paper discusses such a site investigation designed to determine the problems and solutions inherent in the driving of the Trans Koolau Tunnel. The paper will describe the various types of tests to be performed, how the results are to be used and the interrelation of the various tests themselves.

Jan 1, 1997

Commencing from a platform acknowledging the capability of the Russian mining industry in open cut and underground mining operations a revitalisation of the industry will depend on an assimilation of mining economics and on an opportunity for technical training of Russian mining industry professionals.Successful foreign investment in parallel with the reconstruction of the industry rests on an understanding of culture, history, internal controls under central planning, and external factors affecting mining development.

Jan 1, 1997

A combination of new radiometric age dates, local field relationships and the regional tectonic history indicate that the low sulphidation, fault breccia-hosted, epithermal gold-silver mineralisation at Umuna is related to continental rifting processes rather than subduction induced deformation and magmatism. K-Ar and Ar-Ar age dating of secondary sericite associated with the gold-silver mineralisation indicates that the alteration crystallised between 4.0 and 3.2 Ma, whereas relative age relationships and SHRIMP II U-Pb dating of the abundant Boiou porphyry intrusions on Misima confirm that the calc-alkaline plutonism is significantly older (8.1 f 0.4 Ma) and related to a different tectonothermal event. The Woodlark Basin sea floor spreading centre occurs to the north of Misima and has continued to propagate westwards, into the continental basement of the Papuan Peninsular, since the end of the Miocene. The westernmost tip of sea floor spreading centre is presently to the east of the D'Entrecasteaux Islands but would have been to the east of Misima roughly 4 Ma. Many of the young tectonothermal features in the D'Entrecasteaux Islands (hydrothermal activity and associated epithermal mineralisation, metamorphic core complex exhumation, detachment faulting, peralkaline volcanism, half graben type basin formation) can be attributed to major extensional deformation ahead of the propagating rift system. Similar tectonothermal features on Misima are temporally associated with the epithermal gold-silver mineralisation at Umuna, suggesting that the D'Entrecasteaux Islands are a modern day tectonic analogue for Misima at the time of precious metal mobility and deposition. The rapid exhumation of high grade metamorphic rocks and localised

Jan 1, 1997

By John Watson

The earliest known records related to mining document in dramatic terms the fact that mining methods have undergone significant change over the centuries. Wooden wedges, hammers and chisels, “fne setting”, to name a few, were the frst tools used to extract ore .or quarry rock for civilization. These inefficient tools and unsafe practices have been replaced today with some of the highest technology known to man. At the heart of most mining operations is the blasting program which utilizes one of the most efficient tools ever invented.. . explosives. Ever since they were invented, miners have been searching for more efficient products and methods with which to harness this “tool” and make it safer, reliable, and more eficient to use.

Jan 1, 1997

By H. Sevim

The utilization of high sulfur Illinois coal by utility plants has been decreasing since the enactment of 1990 Clean Coal Air Act Amendment. Illinois coal producers can make their coal saleable by offering the choice of taking the combustion by-products from the utility plants and placing them in the abandoned sections of their mines. To be competitive, however, coal producers need to select an environmentally acceptable transportation-handling-placement system through which the cost-per-ton of by-product disposed can be minimized. In this paper, a few such systems are presented. The favorable operating range of each system is determined in terms of distance and tonnage. A case study is given whereby cost analysis is conducted for an underground coal mine receiving by-products from two Illinois utility plants.

Jan 1, 1997

By Trevor Howie, Mal Edwards

"Thiess Contractors Pty Ltd. designed and operate the Mt Owen Mine in the Hunter Valley of NewSouth Wales, Australia on behalf of the owners of the mine, BHP Coal Pty Ltd. The mine is a multiseam open cut coal operation. Mining by Thiess commenced in September 1996 following thecompletion of the coal preparation plant. The location of the mine is shown below on Figure Al."

Jan 1, 1997

By David Reddick

The mining industry is in the midst of dramatic change. Mining activities are moving from industrialized first world countries (Canada, Australia, and the United States) to the third world. This shift is occurring due to depleted reserves, tough environmental standards, and expensive labor in traditional mining countries. During a recent trip to South Africa, I was asked, owing to my educational background in economics and an international involvement in drilling and blasting, what changes could be anticipated in third world blasting practices as labor costs increase. It is from that beginning that this presentation has evolved.

Jan 1, 1997

By Brad H. A Brown, J Paul Tidman

To design a blast, one must give consideration to safety, economics, geometry, geology, production needs, and a variety of other requirements. To compare designs requires the time to develop alternatives, analyze, and then improve on them. A number of tools are available to assist with the first set of requirements, however they are poorly integrated. SHOTPlus is a program to improve the efficiency of blasting operations, by combining measurement and blast design tools, and offers the user the time and means to modify designs and explore alternatives.

Jan 1, 1997

By J. Patrick Powers

In tunneling through water-bearing formations, the expense of controlling the water can have a major impact on overall project cost. The author has seen the cost of an eight-foot, finished sewer tunnel rise from under $500 per foot to over $1,000 when a water problem, anticipated as modest, became severe. There is need for greater professionalism in the approach to groundwater control. The days of the forked stick should be behind us. The basic technology exists. Its application is not yet widespread. This paper discusses predrainage; that is, the lowering of water in advance of tunnel excavation. Both free air and compressed air tunnels are considered. Examples from recent tunnel projects are described. SPECIAL NATURE OF TUNNEL DEWATERING Tunneling is unlike other excavations below the water table in a number of significant ways. The tunnel excavation is always on the critical path; if production slows or stops, there is no other work for the heading crews, no other work to carry the cost of service crews and job overhead. The dewatering commitment must be made well in advance. Construction of wells, and pumping down take time. After the heading reaches a trouble area, time is not available

Jan 1, 1997

In the five years since Great Central Mines Limited (GCM) commenced exploration in the Jundee and Bronzewing areas of Western Australia's Yandal greenstone belt, the Company has been transformed from a junior explorer into Australia's fourth largest gold producer with annual production of approximately 440 000 ounces and mineral resources of seven million ounces of gold.The growth in resources has been driven by a high quality geoscientific approach, supported by a substantial budget for drilling and strong management commitment. In 1997, the Company expects to spend US$30 million on exploration in the Yandal greenstone belt.

Jan 1, 1997

By Andrew H. Merritt

INTRODUCTION The prediction of the engineering behavior of a rock mass depends upon the systematic analyses of the results of an exploration program, and upon the recognition of the significant rock properties in the early stages of excavation. The variations in rock properties in different geologic terrains and the state of the geotechnical art preclude complete success in the former case, and we therefore must rely heavily on the experience gained in the latter phase. The geotechnical information obtained from these two phases is only of value to the design engineer when applied to the rock behavior during excavation and subsequent plant operation. Pertinent questions which must be answered include: how does the joint orientation and frequency effect tunnel support and overall cavern stability; how does the depth of surficial soil or weathering effect foundations or slope stability for portal cuts; are there permeable zones within the rock mass that could lead to leakage problems around penstocks and is the material in these zones soluble or likely to pipe in the long term; and does the proposed engineering structure fit the terrain, or will it inevitably lead to problems requiring extensive remedial treatment. During the early stages of construction there are two types of geotechnical information required; actual rock behavior with respect to the original design assumptions,

Jan 1, 1997