Search Documents

This paper firstly reviews the requirements for container and hopper design for reliable discharge. Discussion is then directed to the evaluation of the consolidation stresses acting in both in both the cylinder and hopper sections during both initial and flow conditions. Here the vast difference, especially in vicinity of the bin outlet, between the initial or filling and flow conditions is highlighted. This vast difference has major design and operation implications. A further major implication is that all bulk solids must dilate to flow. The opportunity to simultaneously attain reliable discharge and partial moisture removal is also examined.The selection of design parameters to maximise the consolidation stresses in both the cylindrical and hopper sections is detailed. In regard to the latter, it is recommended fine coal bins be discharged using low friction lined transition hoppers with large outlet spans. Such outlets will discharge fine coal in a relatively compacted state. This compaction state should exhibit minimum water retention and short term moisture uptake.

Jan 1, 1998

By Baafi E. Y

A heuristic approach for the optimisation of the stope geometry is presented. The heuristic method uses economic model of a given deposit to search for the best combination of mining blocks that results in the maximum profit while imposing geo

Jan 1, 1998

By C. L. Jiang

The selective depression of pyrite obtained from Kentucky No.9 seam in coal flotation with various kinds of inorganic and organic chemicals was systematically examined. Most of the organic chemicals tested showed little selectivity in pyrite depression. It was found that both orthophosphate and pyrophosphate were effective for the selective depression of coal pyrite in coal flotation using fuel oil as a collector. At substantially low concentrations of pyrophosphate, the flotation of coal pyrite was completely depressed over a wide pH range, while the coal flotation remained unaffected. The mechanism of the selective depression of pyrite by phosphates has been explained with the help of thermodynamic calculations of iron-phosphate-water systems and zeta potential measurements. It was shown that pyrophosphate reacts strongly with iron ions of pyrite to form stable hydrophilic iron pyrophosphate complexes on pyrite surfaces.

Jan 1, 1998

By D. P. Venter

When Oryx Mine down-scaled in 1994, focus was placed on development, with the primary aim being the exposure and proving of ore reserves. In order to achieve this aim, development ends had to be advanced to reef at the maximum possible rate. This in turn called for support methods which could keep up with the advancing faces, taking up minimum space and time for installation, while providing on the face a real coverage and effective long-term support. In the majority of the development ends which were located in fairly competent ground, the grouted rod development support proved to be adequate until such time as secondary support in the form of meshing and lacing could be installed. The ends developing towards the eastern boundary of the mine, especially in the ?C? block, encountered extremely adverse ground conditions due to the presence of smectite zones within the footwall quartzites. Smectites are a group of montmorillonite clay materials, mainly composed of hydrous aluminosilicates. They occur as minute platy crystals in the rock mass and are especially notable for their ability to absorb liquids. Generally, the zones are found in between the bedding planes of the host rock, and may vary considerably in thickness over short distances. Wherever the smectites were exposed by the development blasting, the rockwalls weathered as the smectites absorbed water and the condition of the tunnel rockwalls deteriorated rapidly. When the smectites were left exposed and allowed to weather, it became almost impossible to install secondary permanent support such as meshing and lacing at a later stage. To minimise the exposure time and subsequent deterioration of the smectite zones, it was recommended that all development ends encountering smectites be shotcreted as soon as possible after blasting. In developing a shotcreting support methodology, both a drycreting and wetcreting system were investigated. The situation at the time ruled out the use of a wetcreting system on the basis of the extensive and costly infrastructure required, as well as its limited manoeuverability. Instead, it was decided to opt for as maller scale but more manoeuverable drycreting system. The system utilized a number of portable drycrete machines with pre-bagged cement, which could support several development ends in close proximity. Initial trials using normal 30 MPa shotcrete on 19level proved successful and the system was implemented.

Jan 1, 1998

By Arit I, Adisoma G

General Limit Equilibrium Method (GLE) and Janbu's Generalised Procedure of Slices (GPS) are two limit equilibrium methods in slope stability analysis which satisfy all equilibrium conditions. Numerical difficulties associated with these metho

Jan 1, 1998

Humankind's interest in measurement of human physical strength probably dates to the first humans. At that time, life was truly a struggle in which the fittest survived. To a great extent, fittest meant strongest. Interestingly, current interest in human physical strength in the workplace stems from 1970-1980s vintage research demonstrating that persons with adequate physical strength are less likely to be injured on physically demanding jobs. Survival in many modem workplaces may still be a case of survival of the strongest. There is, however, a flip side to this issue - that persons with limited strength are more likely to be injured on "hard" jobs. To address this problem, we can apply what we know about physical strength to job design. "Hard" jobs can be redesigned to be within the physical strength capability of most people. Since physical strength is important to these jobs, we must find ways to quantify it through testing. This publication concerns human physical strength testing. Its purpose is not to recommend any particular type of testing, but rather to describe the types of testing available and their uses. It is up to each individual user of strength testing to decide which testing technique is most appropriate for his or her particular application. This booklet discusses four types of strength testing: isometric, isoinertial, psychophysical, and isokinetic. Human Strength Before describing the different types of strength measurement, we must define the term "strength" and explain the concept of strength measurement. Strength is defined as the capacity to produce force or torque with voluntary muscle contraction. Maximum strength is defined as the capacity to produce force or torque with a maximum voluntary muscle contraction.(1,2) These definitions include some key words that must be explained. A voluntary muscle contraction is "voluntary." When a person's physical strength is measured, only the effort the person willingly puts forth at the time is measured. Thus, when we test a person's "maximum strength," we are not measuring his or her actual maximum, but some lesser value representing what he or she is comfortable expressing at the time with the existing equipment and environmental conditions. Interestingly, when researchers startled persons being tested (e.g., by setting off a starter's pistol behind them), they have found significant increases in measured strength.(3) It has been hypothesized that the lower strength displayed during normal testing provides a margin of safety against overloading and damaging muscle tissue. The test equipment and the tested person's familiarity with the process also influence the "voluntary" strength output. The interface between the tested person and the test equipment is particularly important. A poorly designed interface induces localized tissue pressures that vary from uncomfortable to painful. In this situation, testers are measuring voluntary discomfort tolerance - not strength. It is important for strength researchers to keep the "voluntary" nature of their data in mind when they are designing their equipment and protocols.

Jan 1, 1998

By Dan L'Heureux, Joe Haid, Stephen H. Chung

Most coal deposits in Western Canada involve steeply dipping multiple seams. An efficient way to recover coal seams would be to drill through the seams and blast both the overlying and underlying waste material in one shot without disrupting the coal seams while fragmenting the waste rock for easy removal. This requires special blasting techniques as reported by Chung and Jorgenson in 1985.

Jan 1, 1998

Gravity-driven rock falls account for a large proportion of all fatalities and injuries in underground mines. Potentially unstable blocks of rock are found in the hanging wall of excavations, which may be delineated by natural joints or stress fractures. These blocks, referred to as keyblocks, will fail if their weight exceeds the support capacity or if they are located between support units. This paper describes a computer program which simulates blocks in the hanging wall of an excavation based on measured properties of fractures and joints. Keyblocks are identified and placed at random locations in a predefined excavation. The keyblocks are tested against the support to determine whether they fail the support, drop out between the support or are stable. By repeating the procedure several thousand times, statistics of the probability of failure of the keyblocks are obtained. This approach allows the relative hazard associated with different types of support or excavation orientations to be obtained. It is concluded that a probabilistic approach is suitable for the evaluation of supports effectiveness in situations where large numbers of discontinuities or stress fractures are exposed in excavations.

Jan 1, 1998

By Debbie Laney

DOUG HALBE: Second in our quick run-through on "Operating Ideas That Have Saved Me Some Bucks," was Debbie Laney of Rayrock Mines. Debbie apologizes. She can't be here. But she said, "Doug, don't worry. I've asked Mary Korpi to present the paper. We're both short, blond, and wear glasses. Nobody will know." [laughter] Mary, I caught it right away. You ladies can't fool us. Debbie, who wrote the paper, has spent almost her entire career in operations. She is currently metallurgical manager of Rayrock Mines in Valmy, Nevada. Mary Korpi is also a real operator (that doesn't sound right). She has been responsible for a number of operating areas at Newmont's Nevada operations, and she is currently taking a break from operations as manager of public relations/employee communications for Newmont Gold in Carlin. MARY KORPI: They told us this year at Newmont that we were going to have to work twice as hard. I had no idea it meant I would have to work for another company, too. Over the years, and many times in association with work for mid- to small-size mining companies, there have been two areas that seem to have been the focus of cost savings when looking at new facilities or new processes.

Jan 1, 1998

By M. J. Nicol

The kinetics of the dissolution of colloidal silver in aerated cyanide solutions has been investigated with the aim of developing a relatively rapid and convenient method for monitoring the ?leaching power? of solutions typically used in the cyanidation process. Experimental results obtained are consistent with an electro-chemical model, in which the mixed potential is set up in the active region of the polarization curve for the anodic dissolution of silver, giving rise to a rate of dissolution which is controlled by the rate of mass transport of either cyanide or oxygen to the surface of the silver. The rate of dissolution of colloidal silver was found to respond to variations in the reactant concentrations in a similar manner to gold (and silver) in a typical free-milling ore. The use of this technique for the monitoring and control of the cyanide leach process is discussed.

Jan 1, 1998

By D Craw, J Becker

Post-metamorphic structural evolution of Otago Schist resulted in a pattern of northwest and northeast striking faults and fractures cutting the basement rocks. These faults have been reactivated several times since Mesozoic metamorphism. Gold-bearing quartz veins which have been exploited sporadically over the past 130 years are almost invariably hosted by northwest striking structures, and most exploration has been focussed on these structures. There is evidence for hydrothermal activity and mineralisation along some of the northeast striking structures, although there has been very little work done on these structures. Our study is attempting to characterise the hydrothermal processes in the northeast structures, in comparison to the northwest structures, in order to see if further detailed exploration is warranted. There is evidence for both normal and reverse senses of movement on northeast striking faults, and some of the faults have evidence for early ductile deformation overprinted by later brittle structures. Northeast striking structures host stibnite mineralisation in places, and faults are locally silicified or extensively impregnated with ankeritic carbonate. Sulphides are rare in veins, but do occur in some hydrothermally altered host rocks. Hydrothermal haematite accompanies extensive silicification along the Manuherikia fault zone near Alexandra. Anomalous gold concentrations occur in some hydrothennal zones, and in downslope sediments in some localities.

Jan 1, 1998

By Donald A. Bruce

Various types of contemporary Deep Mixing Method (DMM) techniques have been used in the United States since 1986. Such techniques owe their origins to Japanese and Scandinavian developments, which began almost three decades ago. The growing demands of urban infrastructure development and rehabilitation have created a very active and rapidly expanding market demand in the United States especially since the early 1990s, and there is a clear need for a new and fundamental review of the surprisingly large number of DMM techniques that are being used domestically, or are available in other parts of the world. Following a summary tracing the historical development of DMM, and a generic classification of applications, the paper provides a review of each of the many different proprietary methods, which the authors have identified during preparation of an international survey funded by the Federal Highway Administration (FHWA). Data are also provided on commercial aspects of the various DMM techniques worldwide.

Jan 1, 1998

By I. Bock

Selective Blast Mining (SBM) makes use of milli-second sequential blasting technology to separate the valuable reef material from waste rock in the blasting operation at stope faces in the mining of tabular ore bodies such as exist in the gold and platinum mines in South Africa. The waste rock is cast blast to the back of the stoping area, and the reef material is fractured and deposited close to the stope face. Only the reef material is transported to the surface. A simplified economic model is presented to evaluate the economic benefits of SBM. Although premature, in that adequate experimental demonstration of the validity of the model has not yet been possible, the model is presented since it indicates substantial benefits in the case of narrow reef gold mines. It is suggested that many marginal mines should seriously consider SBM. Benefits can also be realised in platinum mines, but a lot more experimental work is necessary to establish cost parameters more reliably. Some practical experience in the use of SBM in the mining of the UG2 reef is presented.

Jan 1, 1998

By A. Vien, B. C. Flintoff, R. P. Edwards

"A major thrust in industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements in control performance can be achieved by getting back to the basics.IntroductionEvery modem concentrator has a state-of-the-art computer control system in place. Several of these are contemplating installing, or have installed, advanced control systems, such as expert systems, but the foundation of their control system remains the PI controller. Although the authors are not aware of any survey or published information for the mineral processing industry, it is reasonable to assume that it would be similar to the pulp and paper industry. ""The average [pulp] mill has some 2000 control loops of which 97% use PI control. This means that PID, dead time compensation, adaptive controllers, specialized algorithms, ... , constitute only 3% of the installed base."" (Bialkowski [1992]).Bialkowski [1992] also stated that ""If you have been keeping score, only 20% of the loops surveyed actually decrease variability in automatic over manual mode of operation, in the short term."" He attributed the problems to: poor tuning (30% of all loops), control valve problems (30% of all loops) and process problems (20% of all loops). There appear to be a serious need to go back to basics and review the existing control system."

Jan 1, 1998

By Stephen H. Chung, Kevin Atherton

The main purpose behind this preliminary study was the reduction of costs while maintaining productivity. Finding a way to achieve this balance without compromising controls on safety and quality of blasting results is of continual interest to the mining industry and of particular interest when ore of lower grade is being mined.

Jan 1, 1998

By F. Sawyerr

A bubble population balance model is proposed for the prediction of Sauter mean bubble diameters in mechanical flotation cells. In the model, the flotation cell is treated as two separate, statistically homogeneous zones?the impeller zone, and the bulk tank zone. Balance functions for the rates of bubble breakage, coalescence, recirculation and inlet-outlet events are proposed based on classical chemical engineering research in two- and three-phase fluid mixing systems. An initial simulation of the population balance model shows trends in bubble size distributions comparable to measured distributions in industrial mechanical flotation cells.

Jan 1, 1998

By P Voulgaris

The Osborne Mine commenced production from an open pit in December 1994 with the first ore being hauled from underground one year later. Currently all ore is hauled up a decline by trucks until the shaft system is commissioned in early-1998. The mine is hosted within a multiply deformed and complex sequence of metamorphic, igneous and metasomatic rocks of mid Proterozoic age that are concealed beneath 20-40 metres of Mesozoic sedimentary cover. Epigenetic and largely hypogene copper - gold mineralisation occurs in a close spatial relationship with quartz - magnetite ironstones and is an important example of a significant mineralisation style in the Mt Isa inlier. Life of mine concentrator production, to year end 1997, totals 3.2 Mt of ore at 3.40 per cent Cu and 1.13 g/t Au. Total metal produced was 97 000 tonnes of copper and 2900 Kg of gold (95 600 oz) from some 348 000 tonnes of dry concentrates averaging 28.01 per cent Cu and 6.99 g/t Au. At the start of 1998 OsborneÆs total measured and indicated resource was stated at 11.38 Mt at 3.24 per cent Cu and 1.21 g/t Au with an ore reserve of 11.42 Mt at 2.90 per cent Cu and 1.09 g/t Au. Exploration efforts in and around the mine have been increased since 1996 and have resulted in an early success, with a 28 per cent increase in ore reserves since mine start-up, and the establishment of a 1.5 Mt inferred resource open to depth. During 1997 the performance of the concentrator has exceeded expectations with throughput having been increased to 1.45 Mt per annum. The Mining Cycle at Osborne has proceeded from discovery through feasibility and is currently seen to be in the latter part of the development stage and/or the early part of an expansion stage. This paper will describe the role of geology and exploration within these stages and will highlight how a number of key interpretations and decisions based on geology have both favourably and unfavourably affected the project.

Jan 1, 1998

By Quinn P, Huuskes W

Continued extraction of the No. 3 Seam at Elouera Colliery required the driveage of a sequence of roadways within an area of significantly elevated horizontal stress. Initial roof conditions varied from excellent to very severe as the panel entered the high stress area. The variation was attributed to the extraction sequence, with different roadways "leading" the panel into the high horizontal stressfield.This paper summarises field and analytical work designed to evaluate the use of stress control methods as an effective planning tool. The "leading" roadway of the panel would be required to remain stable whilst experiencing moderate to severe deformation whilst the neighbouring roadways (stress relieved) could be driven at more acceptable advance rates using less reinforcement.The planning implications of developing the panel with stress control methods are discussed.

Jan 1, 1998

By D. Eugene Rannels, Sarah E. Dunsmore, Cara Martinez-Williams, Yu-Chen Lee

"Dunsmore, Sarah E., Yu-Chen Lee, Cara Martinez Williams, and D. Eugene Rannels. Synthesis of fibronectin and laminin by type II pulmonary epithelial cells. Am. J. Physiol. 270 (Lung Cell. Mol. Physiol. 14): L215-L223, 1996.Previous investigations demonstrated that type II pulmonary epithelial cells regulate extracellular matrix deposition as a function of time in primary culture. In those studies, the matrix fraction was analyzed as a whole. The present work focused on two components of the type II cell matrix, fibronectin and laminin. These glycoproteins have differing effects on differentiation of type II cells in primary culture. Fibronectin synthesis was quantitated between day 1 and day 6 in the cells, matrix, and medium; laminin synthesis was quantitated only in the cells. Although total fibronectin synthesis was regulated as a function of time in culture, reaching its greatest value on day 2, the average proportion of newly synthesized fibronectin in the cells (35%), medium (50%), and matrix (15%) remained constant over a 6-day interval. Between day 2 and day 6, the relative abundance of fibronectin messenger RNA increased 6.5-fold. Rates of cellular laminin synthesis did not vary with time in culture. These results support a role for differential regulation of fibronectin and laminin synthesis to determine the composition of the type II cell extracellular matrix. INTERACTIONS BETWEEN THE pulmonary epithelium and alveolar basement membrane may play a role in the physiology and pathophysiology of the lung. Pulmonary epithelial cells and the alveolar basement membrane form one component of the blood-gas diffusion barrier. Integrity of this barrier is crucial to normal lung function. Specific domains of alveolar basement membrane components have been proposed to determine localization of type I and type II pulmonary epithelial cells during lung growth and development, as well as during repair of the alveolar surface after injury (13). In the injured lung, the extent of damage to the epithelium and the underlying basement membrane is thought to be a key factor to determine subsequent repair or fibrotic scarring (3)."

Jan 1, 1998

By Gregory Hendon

Jim Walter Resources, Inc. (JWR), has successfully longwall mined for many years at depths ranging from 1200'-2500'. However, full pillar extraction has proven difficult and generally economically unfeasible. Overburden and redistributed stresses at these depths require relatively large pillars, which become unmanageable with most pillar extraction practices. The economic benefits of taking gateroad pillars as part of a longwall face have been recognized for some time, including increased life of mine recovery, elimination of belt moves, reduced overcast requirements, and improved longwall to continuous miner ratios. Until recently, the associated risks of pulling pillars prevented any extensive use of this concept at JWR. Due to geological, economic, and longwall repeatability problems, JWR accepted the risks, and undertook pillar extractions with longwall faces in several different applications. The applications included taking a stable pillar (250' wide) as a longwall panel, taking yield pillars on the headgate and tailgate of panels, taking yield pillars and stable pillars in the middle of a panel, mining through chain pillars in the middle of a panel, and taking a support pillar on the tailgate end of a panel. This paper describes the background and experience of pillar extraction with longwalls at JWR.

Jan 1, 1998