Search Documents

By A. Cichowicz

In this study, techniques used to design earthquake-resistant structures are applied to the deep-level mining environment. Earthquake engineers seek to identify the cause of potentially damaging resonance, and design or reinforce structures to reduce these effects. Similar techniques have been used to analyse the dynamic behaviour of the rock mass surrounding a stope in a deep South African gold mine. A three-dimensional seismic array installed in a stope at TauTona Mine (previously Western Deep Levels, East Mine) provided an opportunity to examine the evolution of the wave field close to an underground opening. A set of three-component geophones installed in a borehole above the panel revealed the development of surface waves as wave fronts reached the excavation, and an array of vertical component geophones fixed to the hangingwall provided a two-dimensional map of site effects. While the collected data do not include damaging seismic events, quantitative analysis enabled phenomena which could lead to damage, to be recognized. In the vicinity of the excavation, the energy of the seismic signal is generally transformed from high frequency to low frequency. It was found that seismic events with relatively high corner frequency (150 Hz?200 Hz) usually excite several modes of vibration (30 Hz to 110 Hz), while events with low corner frequency (30 Hz?50 Hz) do not always excite higher modes of vibration in the structure. This implies that the rock mass around the excavation is a complex medium, and should be studied using the multi-degree-of-freedom model. A strong structural effect (due to the excavation shape) was revealed as a low frequency coda wave (at 40 Hz and 60?70 Hz), well developed on the skin of the hangingwall. A strong site effect was revealed by changes in signal properties between hangingwall geophones, exhibiting strong resonances around 160 Hz and in the range 200 Hz to 300 Hz.

Jan 1, 2000

By Michael J. Rinker, P. A. Tibble, M. Wiseman, R. V. Nicholson

Tailings, from an active copper-zinc operation, containing about 10% sulphur were investigated to assess the onset of acid production and potential lime requirements for treatment of drainage. Oxygen consumption rates were measured over two years to verify spatial and seasonal variations in sulphide oxidation rates. Shallow cores were collected to assess the quality of tailings porewater and to characterize solids that had been subjected to oxidation and depletion of neutralization potential (NP) for several years. Oxygen consumption data were used to quantify rates of NP depletion and onset of acid drainage from the near- surface tailings. Based on measured oxygen consumption rates and identification of NP remaining in the tailings, future lime use in the treatment plant was expected to rise significantly without mitigation. Geochemical modeling calculations were calibrated with observed oxygen consumption rates and the model results agreed well with actual lime use in the waste water treatment plant during operations. The modeling also demonstrated the benefits of lower lime demands and treatment costs after closure as a result of construction a soil cover on the acid generating tailings.

Jan 1, 2000

The Ministry of Economic Development has as its slogan æTogether making the differenceÆ. The Ministry is required to work in partnership with the private sector, local authorities, Maori economic entities, trade unions and community groups to transform New Zealand's industrial and economic base. The Government is seeking to achieve sustainable and balanced economic development by: being more actively involved in economic management; working in partnership with the public and private sector and with worker and business interests; focusing on adding value in industries (including primary industries) with long term potential; and bringing the tools of economic policy together in a coordinated way. The Ministry, particularly through its operating group Crown Minerals, is committed to working with industry to achieve mutual goals and to obtain continuing investment in minerals and coal exploration and mining and an active New Zealand minerals industry.

Jan 1, 2000

By Rüdiger Wunsch

The new high speed Vienna - St.Pölten line and the Lainzer tunnel are to be connected to the existing Western railway line in Vienna. This involves building an underground cut and cover branching tunnel which will be connected to the Western railway line by ramps. A key structure is the Herzmansky Street tunnel, which has a length of some 820m. It is to be constructed as a cut and cover tunnel using the top down method. The walls of the tunnel are designed as a water resistant structure consisting of double walls, an outer wall of bored piles and an inner reinforced concrete wall. The bored pile wall will be used as a temporary retaining wall during the construction phase and will also be a structural part of the per­manent tunnel wall. The retaining walls of the open pit, which will have a depth of up to 14m and a width of 12m, were investigated as a non-contiguous bored pile wall and overlapped bored pile wall. Preventing ground water from penetrating into the pit is of paramount importance. The high ground wa­ter level is the determining factor for the dimensioning of the bored pile wall and results in the require­ment for a water resistant concrete structure. It has been necessary to adopt adequate measures, therefore, in order to reduce the hydrostatic water pressure during the construction phase, assuming economical pile dimensions.

Jan 1, 2000

By C. J. Boreiko

Traditional patterns of lead and zinc utilization are being evaluated in accordance with new paradigms that seek to ensure the long-term compatibility of global industrial activity with precepts of sustainable development and sustainable consumption. As a consequence, both industry sectors are experiencing intense scrutiny from the international community, and numerous regulatory options are being considered that may impact upon international industry practice. This paper reviews the growing expectations being placed upon industry, and highlights some of the common regulatory concerns being expressed regarding both metals despite their differing toxicological profiles.

Jan 1, 2000

By R. Codell, D. L. Hughson

While benchmarking the integrated finite-volume code MULTIFLO against the analytical solution of Philip et al. (1989) for cylindrical underground openings, we found numerical simulation of dripping threshold flux consistently higher than the analytical solution for both rectangular and unstructured grids. The magnitude of error is proportional to the alpha parameter characterizing capillarity. This may bias estimates of repository performance towards non-conservatism.

Jan 1, 2000

By Michael T. Lambert

The purpose of the this paper is to demonstrate the benefits of using additional instrumentation during load tests of auger-cast-in-place piles. Traditionally, only load and butt displacement are determined during load tests. The results from and methods used to instrument 15 auger-cast-in-place (ACEP) piles as part of six projects are included herein. By instrumenting the piles, the distribution of load along the pile length and load transfer can be determined, allowing the pile capacity to be adjusted or the length/diameter of the pile to be adjusted for the a given required load. The majority of the piles tested were designed as end bearing piles on either shale or limestone bedrock. No discussion of Geotechnical Instrumentation can be started without acknowledgement of the "Red Book." The actual title of the book is Geotechnical Instrumentation for Monitoring Field Performance, by Mr. John Dunnicliff, John Wiley and Sons, 1993. Anyone undertaking an instrumentation program should thoroughly review the Red Book, paying particular attention to Chapters 3 and 4. Instrumentation should not be done just because it can be done. There must be an unanswered question or questions that can be answered with measured data before instrumentation should be considered.

Jan 1, 2000

By S. Veeramasuneni, C. D. Dunbar

The rate of hydration influences many important physical properties of gypsum. Previous research examined the rate of gypsum hydration and related this to compressive strength and microstructure development using BET specific surface area analysis. The analysis of gypsum porosity in combination with BET surface area and rate of hydration remains to be done. In the present study, mesoporosity is analyzed using the numerical method of Barrett, Joyner and Halenda (BJH) to gain a greater understanding of gypsum hydration and microstructure development. The rate of hydration has a significant effect on mesoporosity of the gypsum matrix. The results reveal the effect of mesoporosity and hydration rate on some macro physical properties of gypsum.

Jan 1, 2000

By P. R. Desam, J. D. Miller, A. Datta

The flow behavior of bubble-particle aggregates in separation tanks is important for many flotation systems, particularly for wastewater treatment. These aggregates can be considered as the dispersed phase in a continuous liquid phase of water and the flow characteristics determine the efficiency of the bubble separation process. In this work, a general methodology for the computational fluid dynamics (CFD) simulation of a bubble separation tank is described. This system is analyzed by Eulerian-Lagrangian approach. The momentum transfer from the dispersed phase to the continuous phase is quantified using the Particle-Source-In Cell (PSI-Cell) method. With CFD simulations, the effectiveness of different tank design parameters are evaluated in terms of the extent of bubble separation.

Jan 1, 2000

Jan 1, 2000

By Nicholas Macrae Steven

Abstract - The Shaba-type Luamata Cu-Co(-Ni) deposit (11°50_S, 24°28_E) is located in a tectonic slice of Katangan Roan Supergroup (Mines Group) sedimentary rocks, surrounded by younger Kundelungu Supergroup lithologies in the external fold and thrust belt of the Lufilian Arc. Luamata is a classic central African copper clearing in dense woodland, visible as a tonal botanical anomaly on Landsat imagery. Supergene Cu-Co mineralization (especially malachite and subordinate chalcocite, digenite, covellite, and copper and cobalt oxides) and, probably hypogene, bornite, and chalcopyrite are hosted by altered, but essentially unmetamorphosed, moderately dipping, dolostones and dolomitic shales. Alteration products include talcose dolomite, sericite rocks and intense silicification and brecciation. Friable yellow shale is best mineralized with cobalt (up to 0.43 wt%), whereas, highest copper grades occur in brecciated, silicified shale (up to 13.5 wt% CuO). Soil copper and cobalt contents are up to 2.2 and 0.6 wt%, respectively. A newly identified nickel zone (where soil contents exceed 0.1 wt% Ni) fringes the Cu-Co deposit. Polymictic, matrix-supported breccias with a calcareous matrix that underlie the Cu-Co deposit are interpreted to be fluidization breccias related to thrust tectonics and the emplacement of the Mines Group slice. Although small compared to the Kolwezi district Shaba deposits in the Democratic Republic of the Congo, Luamata exhibits all the classic features of an ore deposit type (with low calcite contents), whose high metal concentrations could potentially be very profitably exploited by low-cost opencast mining and hydrometallurgical recovery methods.

Jan 1, 2000

By S. S. Peng, C. T. Holland

Mountain Top Removal (MTR) mining started in West Virginia nearly thirty years ago. This surface mining method can extract multiple coal seams as thin as a few inches thick with total recovery and minimum rock dilution in very steep mountainous terrain. It is highly efficient even if coal seams are in close proximity and small in aerial extent. Consequently, MTR has been widely used in the Central Appalachian Coalfield (mainly Kentucky, Tennessee, Virginia and West Virginia) for the past thirty years with great success. In that respect, there has been no demand for research and little scientific research has been performed to investigate its impacts on the surroundings in the history of MTR mining. However, in the past two years the debate over the MTR mining has grown quickly and in times become very intensely. This paper describes chronologically the issues raised by various parties, legal actions, its impacts on mining permit application and research projects developed to address the issues.

Jan 1, 2000

By T. G. Paradis, C. A. Mohns

"This paper summarizes the Wren CAT (Clarifier and Accelerated Thickener) deep bed thickener operation at the EKATITM Diamond Mine in Canada’s Northwest Territories. EKATITMs’ thickener project is presented in terms of initial design considerations and present day operating practices. A circuit description summarizes process equipment, reagent systems, and typical process conditions, and details of Wren CAT operating principles are provided. Operating strategies are discussed, with emphasis on process instrumentation and control and operating challenges.INTRODUCTIONThe EKATITM diamond mine, operated by BHP Diamonds, Inc., is located in the Northwest Territories near Lac De Gras, approximately 300 km NNE of Yellowknife, NT. 9000 dry metric tonnes of diamond-bearing kimberlite ore are processed daily. Processing operations commenced in October, 1998.The EKATITM process plant flowsheet features typical steps in diamond recovery plant design. Figure 1 shows the general plant flowsheet. Size reduction and feed preparation are accomplished by crushing, scrubbing, and high pressure grinding rolls (HPGR) through closed-circuit classification with vibratory screens. Heavy medium separation (HMS) is used as the initial stage of heavy mineral concentration. Secondary concentration is accomplished in the recovery plant by attrition milling; wet, high-intensity magnetic separation (both wet and dry); and X-ray sorting.The present budget throughput rate is 9000 dry tonnes per day. This will be increased to 18,000 tonnes during the first ten years of operation. Unlike most kimberlite treatment facilities, which process material from a single ore body, EKATITM’s process plant was designed to accommodate ore from five different kimberlite pipes, each with its own treatment characteristics.All processing, except for primary crushing, is carried out in a temperature-controlled environment in the main process plant building."

Jan 1, 2000

By M. L. Free, L. Anthian

Electrochemical, chemical, and image analysis techniques were utilized together with statistical analysis methods to determine the effect of various anode impurities on copper electrorefining performance. Results indicate that arsenic is a beneficial anode impurity. Anode lead and sulfur are shown to decrease electrorefining performance. Specific emphasis is given to the influence of individual elements on current efficiency, slime particle generation, and cell voltage parameters.

Jan 1, 2000

By C. G. Buttleman, W. C. Brice

In Minnesota, reclamation of active aggregate mining sites is primarily regulated through local permits issued at the county, township, or municipality. However, for abandoned or depleted aggregate mining sites, a responsible party for reclamation is often no longer available. Since 1995, the Minnesota Department of Natural Resources has reclaimed several abandoned aggregate sites using innovative public/private partnerships and emphasizing native plant materials. The purpose of these projects is to demonstrate cost effective reclamation methods that can be utilized by both aggregate operators and local government and to promote mine planning and resource identification as it relates to reclamation.

Jan 1, 2000

By Chris Harnan

This paper describes the geology of three European cities and outlines how the geology has lead to the development of specific foundation construction techniques. Comparative tables of techniques commonly employed are given in Section 5. It can be seen that despite the presence of the 'single market', techniques still have wide diversity despite some similarities in geotechnical conditions.

Jan 1, 2000

By Jason Ryan, Stephen Harria

Q.E.D. (QED) is a blast design and evaluation model that allows full three-dimensional design specification including the development of unique “live” terrains and an unlimited variety of complex charge configurations. QED’s analysis package allows the examination of likely outcomes resulting from changing various design variables in terms of vibration, fragmentation, rock-mass damage and muck-pile profile. Especially applicable to use cautious blasting applications, QED’s damage model uses vibration to estimate rock damage beyond excavation boundaries. This relates directly to operations such as Yucca Mountain Nuclear Waste Repository in Nevada, where damage beyond the excavation perimeter must be tightly controlled. The U.S. Department of Energy (DOE) h as b een studying a site at Yucca Mountain, NV to determine its suitability for long term storage of nuclear waste. The main mechanism of waste isolation will be the natural barrier of the host rock Total Systems Performance Assessment (ISPA) is used to model the excavation design and its behavior over time. Of importance to TSPA is quantifying the condition of the rock-mass before and after excavation. Ideally, there should be no excavation-induced changes to the rock-mass’ structure (removing the requirement to model the effects). At the least it may be possible to keep excavation-induced damage far enough away from waste packages so that modeling of these effects will not be required. QED can calculate a prediction of the extents of blast induced damage to the rock-mass. By using this metric as a design parameter, it may be possible to complete excavation of the repository more rapidly and inexpensively than previously thought, without jeopardizing the structural integrity of the waste containment areas or requiring blast damage to be modeled by the TSPA. This paper will explain the structure of the QED blast modeling system and show the analysis of historical data from Yucca Mountain. Processing of the historical data and the subsequent results will demonstrate how blast modeling can be used on an ongoing basis to assist the excavation process at Yucca Mountain.

Jan 1, 2000

By Peter Duniam, Stephen John Brace

2000 HIGH-TECH SEMINAR Blasting Technology, Instrumentation and Explosives Applications Orlando,Florida,USA July24-27,200O. Objectives:- After completing this session 1. Explain safety issues 2. Do simple initiation design 3. Describe how the system works 4. Demonstrate scanning, hookup, testing and firing 5. Describe hot to do a post blast check 6. Explain how to treat misfired detonators

Jan 1, 2000

Zircon producers are often required to lower impurity levels to meet customer specifications as most of these impurities adversely effect the end use. For example, zircon sand in foundry applications needs to be free of any surface impurities (eg clay, gibbsite and goethite) which otherwise could cause sintering or fusion between cast metal and the zircon mould. Light coloured ceramic grade zircon, typically low in iron oxides and titania, is preferred in ceramics applications. The presence of impurities in zircon sands is a problem in the magnetic and electrostatic separation stages of their concentration. Previous work (Aral et al, 1997) showed that impurities in zircon sand concentrates occurred in the form of stains on grain surfaces, discrete gangue minerals and in the mineral grains. The gangue minerals such as rutile, garnet, xenotime, monazite, spinels, ilmenite, and aluminium silicates in the concentrate in some cases (Aral et al, 1997) contribute significantly to the impurity content of the concentrate. A careful hand picking of the impurity grains from a Western Australian zircon sand showed that the impurity content of the concentrate could be lowered significantly as a result of the removal of the surface stained grains and gangue minerals. The hand-picked ædirtyÆ fraction, comprised about eight per cent by weight of the concentrate, and consisted mostly of iron-oxide/hydroxide-stained zircon, silica grains and rutile, and occasionally ilmenite, monazite, gahnite and other (unidentified) coloured grains. The chemical analysis of the remaining æcleanÆ fraction showed that the major impurities (Fe and Ti) were reduced significantly (Table 1). The reduction in the uranium content was about 30 per cent. The other measured impurities, P, Mg, Al, Th, and Ca remained mostly unchanged as shown in Table 1. The contribution of ilmenite to the overall iron content of æcleanÆ zircon was insignificant as it comprised about 0.1 per cent weight of the æcleanÆ zircon. Rutile was the major source of titanium contamination (about one per cent by weight). Recent work (Aral and Calle, 1999) on zircon sand concentrates from the Murray Basin showed that, under the electron microprobe, the bulk of the impurities occurred in the dark back scattered electron (BSE) regions of the zoned zircon grains. The impurity contents of the light BSE regions and unblemished (unzoned) grains were low. The impurity content in zoned zircons has been investigated on single, relatively large, crystals (McLaren, Gerald and Williams, 1994; Smith et al, 1991; Romans, Brown and White, 1975). These studies generally aimed to investigate the incorporation of U in zircon as zircon is used extensively for U-Pb geochronology owing to its relatively high content of uranium. Smith et al (1991) identified a striking difference in composition between the areas of lower (dark BSE) and higher (light BSE) average atomic number in the zoned zircon. Their work showed in particular that the zones of lower atomic numbers contained very significant amounts of trace metals such as Y, REE, Nb, U, Al, Fe, Ca, Ba and, by difference H2O. In this paper the impurity distribution in zoned zircon grains was investigated on statistically significant number of grains before and after a leach treatment. The distribution of impurities was also measured in unblemished areas to compare the results.

Jan 1, 2000

By Steve Kral

The mining industry in Colorado faces the same problems the industry faces throughout the United States and the world — record low commodity prices and increasing regulatory and environmental restrictions that seemed designed to curtail mining activities. Despite those obstacles, the mining industry in Colorado still contributes about $8 billion annually to the state’s economy in the form of base and precious metals, industrial minerals, coal and associated service businesses and jobs. So the 300 attendees at the102nd National Western Mining Conference felt reason-ably positive about the industry in their state. The meeting is the Colorado Mining Association’s annual conference and was held at the Broadmoor Hotel in Colorado Springs in November. The theme was “Mining in the New Millennium — Achievement + Innovation = Survival.” Experts from Colorado’s mining industry and abroad discussed the challenges faced by the mining industry as it enters the new millennium. They offered insights into how the industry will operate during the early years of the 21st century and how it will survive low prices and increased regulatory restrictions.

Jan 1, 2000