Search Documents

By Hiroyuki Sano, Chikabumi Yamauchi, Mitsuru Tanahashi, Toshiharu Fujisawa, Shin-ya Iwahori

"Pyrometallurgical process using Cu2O-based slag was proposed as a recycling process for copper scrap. However, it is difficult to remove nickel from copper by oxidative refining. Therefore, it is necessary to reduce the concentration of nickel in copper before the oxidative refining. In the present work, the copper enrichment stage in this recycling process, where copper scrap melt is separated into the Fe-C-Cu melt and the molten copper, was taken up and the compositions of both melts were measured. Based on the above results, the distribution ratios of nickel between the Fe-C-Cu melt and the molten copper were calculated. Furthermore, the optimum condition of copper enrichment stage was discussed from the viewpoint of nickel removal and copper recovery. The possibility of recovering 4N-purity copper by using this recycling process was confirmed.IntroductionRecycling is well known as a method for saving resources and reducing environmental damage. More than 99% of copper is used in metallic form - as metal or copper alloys[l]. High-grade copper scrap is directly re-melted and reused, while low-grade copper scrap is transported to copper smelters to be pyrorefined and electrorefined. Nevertheless, a great amount of copper is being stockpiled in the cities and should be recycled in the near future. At that time, the current recycling process will face new problems due to the increases in the recycling rate to the smelters. This includes insufficient combustion heat to melt copper scrap and ·almost no benefit in electrorefining because the scrap does not contain gold and silver. Thus, an alternative pyrometallurgical method for copper scrap refining will be required."

Jan 1, 2000

By Dan Marshall, David H. Watkinson

Abstract - Cobalt, Ontario, is renowned for the 12.6 billion grams (445 million ounces) of silver produced from the area since discovery in 1903 by workers of the Timiskaming and Northern Ontario Railway. Native silver generally occurs with cobalt arsenides and sulfosalts in near-vertical carbonate veins cutting the Huronian sedimentary rocks of the Gowganda Formation, the Archean metavolcanics and/or the Nipissing diabase. All major deposits have been found within a few hundred meters of the unconformity between the Archean and Huronian rocks in general proximity to the Nipissing diabase and volcanogenic sulfide mounds within the Archean meta-volcanics. Silver has been mobilized from one or more of the local country rocks by hyper-saline brines and deposited in or near zones of mixing where the saline brines encounter paleometeoric water transported to depth along the unconformity or local structures. Previous work has shown that chloride complexes are the dominant ligands responsible for silver transport. These hypersaline brines, represented as halite-bearing fluid inclusions at room temperature, have been trapped as primary fluid inclusions within vein minerals. Pressure-temperature conditions of vein formation have been derived from mineral equilibria, maximum lithostat and fluid-inclusion studies. These data are consistent with vein formation occurring over the temperature range 300°C to 350°C, with pressures constrained between 60 Mpa and 136 Mpa (600 bars and 1360 bars).

Jan 1, 2000

By A Croll

A panel cave using LHDs for ore extraction came into production at Premier in 1990 at a depth of 630 metres below surface on the western side of the mine in the BA5 mining block. A post-undercut mining sequence was used with all development on both the undercut and production levels completed prior to the undercut being advanced over the pre-developed drawbells. Support and rock mass damage on the production level was extensive as the undercut moved overhead. Undercutting and coarse fragmentation created problems. The mining sequence was changed to an advance undercut with the minimum of development and support undertaken on the production level prior to the undercut moving overhead. Only once the abutment stresses had stabilised were drawbells developed and final support installed. The height of the undercut drill design was decreased from 18 to 13 metres. The changes resulted in markedly less rock mass and support damage on the production level. Lessons learned in the BA5 mining block on the 630 level were incorporated into planning and scheduling the BB1E mining block which came into production on the 732 metre level on the eastern side of the mine in 1996. An advance undercut mining sequence was planned, undercut height was minimised and undercutting parameters were optimised in terms of the BA5 experience. Numerous problems still occurred. As the undercut area increased in size severe spalling from the cave back resulted in vertical propagation of the cave to a height of 30 metres instead of the planned 13 metres. The resultant coarse fragmentation created secondary blasting problems and an excess of undercut ore that had to be loaded and trammed, slowed the rate of undercut advance. The planned mining sequence was compromised and considerable support and rock mass damage resulted on the production level below. Once these problems had been overcome the undercut advanced at the planned rate and continuous caving initiated at the predicted hydraulic radius. At a later stage the unexpected ingress of water hampered undercut drilling and slowed the rate of undercut advance in a section of the cave. Leads and lags between adjacent tunnels and the overall face shape could not be developed as planned. The rate of natural horizontal cave propagation exceeded the rate of undercut advance and three undercut drilling tunnels were extensively damaged. More tunnel development on the production level prior to undercutting than was planned resulted. The slow advance of the undercut and high abutment stresses caused extensive damage to installed support and the rock mass on the production level, 15 metres below. Experience in the BB1E mining block on the 732 metre level has taught that an advance undercut mining sequence reduces damage on the production level markedly. Extremely tight control on the rate of undercut advance, leads and lags between adjacent tunnels and overall undercut face shape as well as extraction ratio, tunnel development and support sequence on the production level below is required. Premier Mine plans to implement a block cave at a depth in excess of 1000 metres within the next decade. All the experience gained on current mining levels together with data collection and numerical modeling is being used to plan the proposed mining operation. The geotechnical challenge of mining at this depth in weak rock has been identified as the greatest risk to the project. Challenges centre around adopting the correct mining sequence, limiting the extent of rock mass damage associated with undercutting and effective support. The hydraulic radius needed to initiate caving, fragmentation, drawpoint spacing, secondary blasting and the possibility of seismicity are geotechnical concerns that are being addressed. Results to-date suggest that a pre-undercut mining sequence with all development and support on the production level carried out only after the undercut abutment stresses have passed overhead will have to be implemented.

Jan 1, 2000

By I. Benning

Since the dismal performance of the Rand Mines management was called to account by its shareholders in 1994, the waves of change have continued to ripple across the South African mining industry .The number of listings on the gold board of the Johannesburg Stock Exchange, that once numbered 40 or 50-odd, have now dwindled to no more than a handful as unprecedented restructuring has taken place. The redefining of the industry has not been limited to the gold sector, but across the base metal, coal, diamond, platinum and industrial mineral sectors as well. At the same time the Mining Houses began to reconsider their funding strategies. Originally established in the early part of the century to ensure the long-term sustainability of their group mining operations by providing substantial financial muscle and technical support, the Mining Houses were faced with a rapidly changing political environment, which proved to be a critical catalyst in giving momentum to the change. Furthermore, the significant development costs and increasing risk profile for new projects, coupled with pressure from shareholders demanding respectable returns, opened the door to opportunities for banks to begin providing external debt by the way of project finance. However, the provision of long-term debt to the South African mining industry had generally not been common since mining companies had financed new projects with equity, or with the cash flows from existing operations. Those banks that had the appetite for exposure to the perceived high risks of the mining sector rapidly built up specialist resource banking divisions capable of addressing the increasing demands of the industry. The application of project finance, the principles of which were developed in the 1970s specifically for infrastructure projects and privatization, is now commonly applied in the financing of greenfield and brownfield mining projects. This paper outlines the approach that lending banks would typically adopt when arranging or providing mining project finance, their usual areas of concern and the way in which the finance is structured to mitigate the many inherent risks.

Jan 1, 2000

By J. S. Y. Wang, R. C. Trautz

A 9-meter-long drift was constructed in the unsaturated-fractured tuff at Yucca Mountain to evaluate the potential for water seeping into an underground opening. Forty seepage tests were performed by releasing a finite volume of water at a constant rate into short test intervals located in boreholes positioned above the drift. The seepage threshold flux, defined as the liquid-release flux at and below which water will not drip into the opening, was determined for 10 test intervals. The seepage data, observations, and model results indicate that a seepage threshold exists because a capillary barrier diverts water around the opening.

Jan 1, 2000

By Jack Hayes

The design and construction of deep foundations involve many uncertainties. For the designer there are uncertainties regarding soil and ground water variability, regarding sampling and lab testing, regarding analytical techniques and regarding construction technique. The latter being the uncertainty over which the engineer has least control and which may have the greatest impact on capacity. Foundations with a high design factor of uncertainty can be very costly. Foundations designed with a high factor of uncertainty may have a low factor of safety, which can be even more costly.

Jan 1, 2000

By Geoffrey Birch

A skilled and efficient workforce is a pre-requisite for the success of modern construction companies. The drive for improved performance, innovation and best value must be matched by the enhanced skills of the construction personnel. Training has been accepted as one of the essential cost effective elements to achieve these goals. The foundation industry demands particular specialist skills and requires focused training for its dedicated operatives. The introduction and development of specific training qualifications for the foundation sector is providing significant benefits.

Jan 1, 2000

The functional design of a pavement relates to the selection of appropriate wearing course materials which optimise the trafficability of a pavement. Trafficability is dictated to a large degree by the choice, application and maintenance of locally available wearing course materials. Poor functional performance results in decreased safety and operational efficiency and increasing road and vehicle maintenance requirements. An optimal functional design will include a certain amount and frequency of maintenance (watering, grading etc.) and thus maintenance itself can be planned, scheduled and optimized within the limits of required road performance and minimum vehicle operating and road maintenance costs. Since no wearing course material selection guidelines, tailored to the specific needs of surface mines, were available, there was the need to identify appropriate selection guidelines for the range of materials commonly encountered for road building on South African mines. The aim of this paper is to present an overview of the functional design method for mine haul roads and, through an analysis and quantification of existing wearing course material performance, to recommend appropriate wearing course material selection guidelines. The functional design technique has been applied at a number of mines and is illustrated by an application case study which demonstrates the potential reduction in total transportation operating costs associated with the optimal functional design.

Jan 1, 2000

By Todd M. Ruff

An average of 13 mine workers are killed each year by being run over or pinned by mobile mining equipment. At surface mines, these accidents commonly involve large dump trucks that drive over a smaller vehicle or a person that is in the dump truck’s blind spot. One method of detecting a person or another vehicle in a blind spot is to use some type of sensor technology such as radar or radio-frequency identification (RFID). Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health tested a number of commercially available and experimental sensors that monitor obstacles in a vehicle’s blind spots. None of the sensors had been previously applied to the specific problem of rigid-frame surface mining trucks. This report documents the procedures and results of tests conducted after RFID and radar systems were mounted on a 50-ton-capacity dump truck. It was determined that both RFID and radar technology show promise for detecting obstacles in the blind spots of mining equipment; however, more development work is needed to meet the unique requirements of mining equipment and the mine environment.

Jan 1, 2000

By L. I. Gyrskia, Y. V. Andreev, T. N. Greiver, G. V. Petrov

Traditionally, chromite ores are regarded exclusively as a monomineral raw material for extraction of chromium. The results of the investigations indicate a wide range of PGM in the Ray-Iz chromites, amounting to 1-3 ppm PGM. The study of products of primary gravity concentration from heavily and lightly disseminated ores (Tsentralnoe deposit, Ray-Iz block), showed that the platinum-group minerals are concentrated in the tails and slimes of the processed products, containing 10-30 ppm total PGM. Preliminary data make it possible to conclude that an in-depth study of the platinum mineralogy of the Ray-Iz block chromite ores is necessary to develop a process that will produce both chromium and the PGM.

Jan 1, 2000

By Arturo Ressi di Cervia

From the times when men in lacustrine environments drove wooden piles into the mud to elevate their dwellings, until the beginning of the twentieth century builders reacted to the conditions found in the location of their proposed structures by attempting to distribute their loads in ways that could be supported by the foundation's soils; or, if those were unsuitable, by moving the structure, whenever possible. While many major structures were built on stable ground (the pyramids were founded on rock), others were built on [ ]

Jan 1, 2000

By Yvone Franco Crosato

The dense population of Hong Kong requires the construction of tall buildings in reclaimed areas or perched on the slopes of the many hills. The large loads to be supported are carried by deep foundations. Many of those are bored piles, to rock, of diameters up to the 3.0 m. of today.

Jan 1, 2000

By Michael W. Lewis

The latest downturn in the world’s metal prices has forced many mining companies to focus on cost reduction and productivity improvements to remain competitive. Maintenance represents a significant part of the overall operating costs in the mining industry. A structured, proactive maintenance approach, such as reliability-centered maintenance, can achieve cost reductions and productivity improvements. Remote condition-monitoring systems are becoming commonplace because they have the potential to identify problems before failure. Detection of equipment degradation before failure will enable repairs to be scheduled, thereby reducing costs and interruptions to production. The mining industry is in the midst of uncertain times. Decreasing commodity prices, demand, head grade and capital availability along with increasing environmental requirements have put pressure on mining companies to significantly reduce costs to maintain short- and long-term viability. Corporations are looking at expansion, merger/consolidation and financial/hedging programs to achieve these cost reductions. Mines are reducing costs by eliminating all but essential expenditures, increasing production levels, reducing overtime and investing in new technologies.

Jan 1, 2000

By M. M. Rajkovich, L. Adams, J. J. Zaluski, S. Gardner

In 1998, Kentuckians for the Commonwealth filed an Administrative Petition with the Kentucky Natural Resources and Environmental Protection Cabinet to designate 8,903 +/- hectares (22,000 +/- acres) on Black Mountain, which contains the state’s highest point, as unsuitable for mining. A fast track legislative process was triggered which could have "taken"100 million tons of coal reserves or, in the alternative, imposed severe restrictions on mining. Even with all parties represented by reasonable individuals, this process can be extremely cumbersome and expensive. The legal and technical preparation for this unusual hearing process as well as issues and strategies of the negotiated resolution are reviewed.

Jan 1, 2000

By H. Möhle

Premier Mine is a large underground diamond mine, situated at Cullinan in the Gauteng Province of South Africa. The mine hoists over 3 millions tons of diamond bearing kimberlite per year, from a modern, mechanized panel retreat block cave mining operation. Troughs sited at the base of the cave are developed into the overlying caved ore, allowing loading access to the ore through draw points. Trough opening is therefore a vital aspect of the mining operation. Most of the production is dependent on fast, reliable and safe trough opening. Successful trough openings are achieved under difficult mining conditions due to restricted void, long up-holes and the inherent properties of kimberlite?soft, elastic rock with a high swell factor. Early in 1998, Premier Mine undertook a joint development project (with an electronic initiation system supplier) to determine whether the use of a fully programmable electronic detonator system would enhance the mining cycle in the trough opening process. Blasting commenced in February 1998, initially with blasts of a similar size and duration to those that had been previously blasted with shock-tube systems, to confirm the operational capabilities of the blasting system. The accuracy, reliability and flexibility of the electronic delay detonators (EDDs) minimized associated risks for re-engineering of the trough opening process. Further, as blast timing was optimized, larger blasts were successfully initiated. To date over 20 troughs have been opened successfully with the use of EDDs. Not only did it take less time to open troughs, but also drilling and blasting operations have been optimized, as well as an overall improvement in safety. This paper details the benefits that EDDs have delivered to Premier Mine in this area. The logic followed is: ?Review of the original trough opening practices ?Re-engineering of the trough opening process ?Implementation of EDDs ?Evaluation of improvements and conclusions.

Jan 1, 2000

By Thomas Lautsch

After a short description of geology and gateroad roof support technology in the German coalfields the development of roof bolting as primary roof support is presented. Based on geotechnical parameters, different strategies used for roof support at depths of 3,300-4,600 ft. are explained. Strict quality management and a strict monitoring program are part of the entry development. A number of recently finished developments are described such as the introduction of standardized bolts and accelerated resin systems. An outlook of future goals is presented. The paper concludes with a comparison of roof control systems at RAG's mines in the US and Germany.

Jan 1, 2000

By Steve Colbum

LTl’s MapStar LPS (laser positioning system) utilize both tripod mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environment characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, interactive software program, which can be run on any standard PC. Win Prof, the Windows-based analytical software package is used to reduce the data for generating bench face profiles, surfaces, volumes, estimating true burdens and mining ratio calculations. In addition, the software has many other built-in routines to calculate powder factors, toe shear, to map structural contacts and to predict the flyrock potential based on the Burden to Energy ratios. An extensive, built-in library of explosive’s data facilitates these calculations. It will also conform automatically to user-specified minimum and/or maximum burden in relation to the explosive energy, hole diameter and bench geometry - for both vertical and inclined holes. Numerical data can be represented in 2D or 3D to emphasize the hole-burden-face relationships.In this workshop, the MapStar LPS instruments and Win Prof analytical software will be thoroughly demonstrated. Demonstrations include equipment configuration, typical field setups and several effective survey procedures, including processing of some sample data.

Jan 1, 2000

By I. J. Wu

China’s land area, comparable in size to United States or Canada, contains diverse geological environments and mineral resource potential. The diversity in geological environments is such that the potential for developing many world-class mineral deposits in China is good. However, China’s mining sector was not open to foreign investment until the1990s. The long-term prospect for Chinese resource development is attractive because of China’s enormous population and cumulative demand for minerals. Approximately 33 foreign mineral companies, including 11 major internationals, are to various degrees active in China. Chinese mining laws and regulations pertaining to joint ventures with foreign companies are, from the international investment prospective, evolving slowly, but positively. This positive trend is continuing under the current government reform process, which is moving China towards a freer market economy. Although improving the enforcement of relevant laws and regulations is an ongoing process, the environment for mineral investment and joint ventures is increasingly more accommodating to foreign companies.

Jan 1, 2000

Distinguished guests ladies and Gentlemen. As many of you know, before I became a Labour Member of Parliament, I had an unusual career path for a politician, in that I spent quite a few years working in the business community. In other words, I was mainstreamed before I was institutionalised. Given that some of this time was spent working for the then Macraes Mining Company Limited, now Gold and Resource Developments NL, I feel that I may have a perspective on how things are seen, on both sides of the fence. In terms of public perception and esteem I am not sure which career option was the step up and which was the step down. So far what I have found very familiar, is that in both roles there is a gulf between the reality and the perception of that reality - a gulf that is both huge and hard to bridge. I think it is a point worth making here amongst another busy industry cluster, that we can all too easily get so embroiled in the day to day activities, that we lose sight of how this might look to those running on a different treadmill. I can still remember scratching my head at the beginning of some days, as I worked to get new mining projects started that I knew were going to bring real jobs and economic benefit to New Zealand, but ending the day feeling like I may instead have been proposing bringing back both strip mining and slavery. If I learnt one valuable lesson out of that time it was this: .... mining has become so publicly demonised on the road to ecological nirvana, that even attempting a lucid dialogue on mining issues, with some, is incredibly difficult.

Jan 1, 2000

By G. Taylor

A 21st Century worker is one who works less with his physical power and more with mental ability. Such a worker is more skilled than a labourer and is consequently rewarded accordingly. A21st Century supervisor is one who ensures that workers are constantly supported so that they can maximize safety and productivity. A 21st Century manager is one who constantly searches for ways to maximize returns for the various stakeholders. Given the well-known constraints in narrow reef mining, all of the above is meaningless unless a mining method is found which provides conditions which support the 21st Century initiatives. [ ] The identified mining method is a continuous non-explosive stope breaking system using rocksplitter technology. Rocksplitting is defined as: The fragmentation of rock through high energy pulse wave transmission in a fluid-filled hole or hydro fracturing. Shotholes are effectively filled with a water-based geland 30 grams of explosive after which the hole is closed off with a ?rocksplitting gun?.

Jan 1, 2000