Search Documents

By Maurice Deul

For the first half of the 21st century, the United States will rely on the same mix of fuels it has for the past 50 years. Petroleum for the United States will cost more and availability will decline as developing nations modernize. Increased use of natural gas for electric power generation will result in stress on the gas supply. Coal will be the fuel of last resort. More than half the petroleum used is imported, about the same amount as used for transportation. Only coal can provide relief by fueling railroads through electrification while encouraging “piggy-back” trailer haulage, co-generation for manufacturing and expanded passenger service.

Jan 1, 2002

By John E. Tilton

Real copper prices during the past several decades display two striking characteristics. First, they are highly volatile. Within a year or two, copper prices can rise or fall by 30% or more. Second, over the longer term, they are falling. Indeed, since 1970, the secular trend price for copper is down by more than 50%. Figure 1 highlights both of these characteristics. It shows the average annual US producer price for copper since 1970 measured in constant 2001 US dollars. While the London Metal Exchange (LME) copper price is not shown, it and the US producer price have for some time moved more or less together. So pronounced short-run fluctuations around a significant long-run decline describe copper prices, not only in the United States, but around the world.

Jan 1, 2002

This paper deals briefly with productivity-enhancing advances in shaft sinking technology in South Africa post-World War II in general and the developments and application of long rounds since the 1980s in particular and is amply illustrated.It touches on the conversion to circular section, concrete lined shafts, the introduction of tungsten carbide drill bit inserts and grab lashing; expounds the rationale driving the development of longer rounds; and then describes the evolution of long rounds using hand-held and mechanically mounted rockdrills in South Africa and Canada by both local and foreign contractors. The recent experience gained on the sinking of the South Deep Main Shaft follows. Results obtained from this experiment are tabulated and commented upon. The paper concludes with the postulation of æwhat nextÆ and æwhere toÆ scenarios. Addenda include a list of shaft rounds in excess of three metres in length blasted in the Main Shaft at South Deep and their results, typical round design, manufacturerÆs specifications for the 6 m shaft jumbo and rock drills.

Jan 1, 2002

By R. J. Durrheim

The DEEPMINE Collaborative Research Programme was established to create the technological and human resources platform that would make it possible to mine gold safely and profitably at depths of 3 to 5 km. The DEEPMINE Programme has four goals: to acquire knowledge of and develop appropriate technology for new ultra-deep level mines, to stimulate education and training, to establish a culture of innovation, and to encourage rapid technology transfer and implementation. The research programme was launched in July1998 and will be completed in March 2002, with the final year focusing on the transfer of knowledge to the industrial partners. DEEPMINE represents a new model for conducting mining research: it is driven by industry needs; emphasizes collaboration between industrial partners, research organizations and tertiary education institutions; and has a novel joint-funding mechanism. DEEPMINE has employed a range of vehicles to transfer knowledge to its industrial partners. Novel aspects include: (a) electronic publication of Summary Reports and Guideline Handbooks that seek to consolidate the huge body of knowledge comprehensively and concisely, (b) a series of DEEPMINE Schools designed to enable industry practitioners to apply the knowledge to their current work situation, and (c) Consultancy Reviews, where DEEPMINE specialists seek to apply knowledge to specific real problems on mines.

Jan 1, 2002

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health are investigating technologies that could be used to detect objects, small vehicles, and pedestrian workers that may be in the blind areas of haulage equipment used in mining and construction. A detection system that warns the equipment operator that there is an obstacle nearby could prevent collisions and save many lives each year. One popular technology for collision warning systems is radar. Several different types of radar have been tested in the laboratory and on mining equipment. Early in the study, questions arose concerning the best way to test radar systems. Many factors affect the performance of radar, including the size, shape, and composition of the object that is to be detected; the height of the radar antenna(s); and the relative motion of the radar system and/or object. This report discusses several different test procedures and test targets and recommends methods to determine how effective a radar system will be in detecting a person near heavy equipment.

Jan 1, 2002

By Steve Kral

The domestic mining industry may be in the doldrums but there appears to be hope, at least from a regulatory standpoint. At least one US senator believes that the events of Sept. 11, 2001 made many citizens see the need for the country to become more self-reliant on its growing energy needs. Even before that tragic day, however, the Bush administration was making a strong push to open up more public land for energy and natural resource development.

Jan 1, 2002

By C. O. Brawner, J. Kalejta II

The classical approach to control rock fall and ravel in open pit mining has been to use catch benches. The width and volume of benches is most dependent on the bench height, size of loading equipment, blast damage to the face and mining regulations. This was compatible with open pit slopes of less than about 45°. As our understanding of rock mechanics and blasting control has improved over recent years, much steeper rock slopes can be developed at many open pit mines. However, narrower benches result with less rock fall capacity. The transportation industry has been very successful in using catch fences to protect highways throughout North America and Europe for years. The authors recommend that cable and ring net fences have a potential major application in open pit mining to allow steeper rock slopes with significant economic benefit. This paper outlines the application, design and operation of catch fences in surface mining for specific conditions. Typical case examples are presented.

Jan 1, 2002

By Thomas J. DeMull

Development of the Batu Hijau copper project was completed in the fourth quarter of 1999 with the formal handover and start-up of ore processing facilities. The project began in August 1996 when the owner, PT Newmont Nusa Tenggara (PTNNT), awarded an engineering, procurement and construction (EPC)contract to Fluor Daniel (FD) for the development of the project. This included a copper concentrator, port, power plant, town site and infrastructure. PTNNT managed the development of the mine and the procurement of the mine equipment. In 1996, Batu Hijau was the largest mining project ever undertaken. Developing the Batu Hijau Mine was complex. It involved the work of thousands of people in all parts of the world to plan, engineer, procure, fabricate and manufacture equipment, supply and deliver materials and equipment, and build the plant.

Jan 1, 2002

In 1991, Placer Dome Venezuela established a 70% stake in Minera Las Cristinas, to mine the Las Cristinas gold deposits in Bolivar. This case study examines the multi-sectoral partnership arrangement that was developed to improve health services near the proposed Las Cristinas gold mine. The investment climate in Venezuela is uncertain and the socio-economic circumstances are potentially hostile. Despite that, the partnership between the mining company, local communities, government agencies and an international health nongovernmental organization (NGO) collectively leveraged nearly $2.5 million to build and operate a community health center.

Jan 1, 2002

By J. D. Noll

Elemental carbon (EC) is used as a surrogate for regulating the exposure to diesel particulate matter (DPM) of underground metal/non-metal miners. EC was chosen as a surrogate because EC is selective to DPM and is a major component of DPM. Using EC as a surrogate also gives one the advantages of no sampling artifacts and being able to sample at all locations in the mine. Currently, EC represents DPM well in underground mines. Some control technologies have been shown to possibly alter the relationship between DPM and EC and characteristics of DPM. Therefore, future work will investigate the relationship between DPM and EC as new control technologies are implemented.

Jan 1, 2002

The relationship between comminution testwork results and the milling circuit that is subsequently selected is not a direct one and frequently involves recourse to databases of past test results. This in itself reflects the lack of a systematic engineering approach in the design process. This paper reviews comminution tests for SAG mill design in an attempt to identify where the essential information comes from that will be used in mill selection. The conclusion is that results from traditional test methods, including obscure and little used procedures like the Mokken test, are more valuable from an engineering perspective than parameters for breakage rate based modelling. Suggestions are made on ways in which existing test procedures can be enhanced in order to generate parameters that can be directly related to characteristics of the milling circuit being designed.

Jan 1, 2002

Novel flotation reagents were developed to improve the flotation of coarse particles. Laboratory tests conducted on an anthracite coal sample from Kyung-Dong Coal Company, Korea, showed that the reagents can successfully clean 2?3 mm top-size materials. Pilot-scale tests conducted on a 1.41 mm x0 coal gave substantially better results than those obtained using kerosene as collector. The pilot-scale test results were used to develop a flowsheet, in which the 1.41 mm x0 fraction is cleaned by flotation and the 4 x1.41 mm coal is cleaned by single-stage spirals. The performance of this circuit was compared with another flowsheet, in which the 0.5 mm x0coal is floated using the conventional flotation reagent, with the 4 x0.5 mm material being cleaned using two separate spiral circuits. The performance of the two flowsheets was compared by computer simulation. The results showed that the flowsheet consisting of the coarse particle flotation circuit can give substantially higher yield sat a given product grade. Keywords: coal flotation, coarse particle flotation, collector, spirals, computer simulation.

Jan 1, 2002

By Dominique Vié

Standards methods covers the procedures for testing deep foundation to determine the force and velocity response to an impact of a pile driving hammer or similar device. The results of analysis generally include an assessment of pile integrity and the value of maximum dynamic stresses. But evaluation of static bearing capacity remains a matter of individual engineering judgment. A new 1D finite elements model has been developed for dynamic stresses and velocity analysis. Following an international benchmark of bearing capacity prediction organised by the Belgium Building Research Institute (BBRI), 12 piles in a site of fissured stiff tertiary clay tested in 1999, and 12 piles in a site of dense sand tested in 2001, comparison are proposed between analysis of dynamic tests and static tests results. A procedure is proposed to take in account the results of dynamic test for evaluation of bearing capacity.

Jan 1, 2002

By H. Arima, T. Fujita, W. Yen

The copper catalyzed gold oxidation and reduction mechanisms in ammonium thiosulfate solution were investigated by Eh-pH diagram based on the optimum reagent combination for 60 mass% -75 µm silicate ore at 16g/t Au with the maximum gold extraction of 92% and the minimum ammonium thiosulfate consumption of 23 kg/t-ore for 24 hour’s leaching at ambient temperature. The gold recovery by cementation was nearly 100% by Zn and Al powders at Metal/Au mass ratio of 30, and around 95% by Cu powder at Cu/Au+ mass ratio of 50. In order to oxidize the gold efficiently with the less thiosulfate consumption, the stable region of [Cu(NH3)4]2+ should be as wide as possible in the region, where [Cu(S2O3)2]3- was more stable than [Cu(NH3)2]+. In order to reduce gold from the pregnant solution with the less metal powder’s (Zn, Cu, Al) consumption, the stable region of [Cu(S2O3)2]3- should be wider than [Cu(NH3)2]+ on copper precipitation. Zinc powder may recover gold more efficiently than copper powder with the similar trend on the effect of ammonia, copper and thiosulfate. However, the large amount of copper will be co-precipitated along with gold since the stability of zinc ammine and thiosulfate complexes are higher than that of copper’s. Aluminium may reduce gold efficiently at higher thiosulfate concentration and pH. These results were confirmed and compared with the optimum reagent combination for finer grind sample at 100 mass% -75 µm, which is the optimum ore size for the standard cyanidation at 1.0 g/ l NaCN to obtain about 95% gold extraction. The optimum reagent combination was concluded as 0.5 mol/l NH4OH, 0.0001 mol/l CuSO4*5H2O and 0.05 mol/l (NH4)2S2O3 with the result of 94% gold extraction and 3kg/t-ore of ammonium thiosulfate consumption. Gold and copper stabilities were well agreed with the result of coarser grind ore thermodynamically. The lower reagent combination will reduce gold oxidation power, but significantly minimize the reagent consumption. From this pregnant solution, nearly 100% of gold was successfully recovered by zinc precipitation at Zn/Au+ mass ratio of 30. Aluminium and copper precipitations resulted in less than 40% of gold recovery at Metal/Gold mass ratio of 30. The reagent consumption cost on this lower reagent combination followed by zinc precipitation was $1.6/t-ore, while the cyanidation was $3.1/t-ore. Thiosulfate oxidation mechanism indicated the similarity to Belousov-Zhabotinsky reaction.

Jan 1, 2002

By R. W. Schutz

"Titanium possesses an exceptional and wide-range resistance to chlorides and their compounds when compared to most corrosion-resistant engineering alloys (CRAs) used in the chemical process industry. This natural resistance to chlorides stems from titanium’s protective, tenacious, and readily rehealable titanium oxide surface film, which is chemically stable over a wide range of pH and redox potentials in aqueous environments. This passive film explains titanium’s elevated resistance to anodic pitting, crevice and stress corrosion, and erosion-corrosion in aqueous chloride environments.Guidelines for successful selection and application of industrial titanium alloys are derived from an extensive laboratory test database and more than forty years of industrial/chemical service experience. These guidelines are simplified, and alloy corrosion performance is assessed with respect to four basic aqueous chloride service categories where selection or consideration of titanium is highly merited. An overview of historical titanium alloy applications in chloride-rich environments in a wide variety of process industries substantiates their exceptional chloride tolerance. These industrial titanium alloys are cost-competitive with stainless steels and nickel alloys, readily commercially available, and routinely fabricated and welded in the shop and field via well-established methods."

Jan 1, 2002

By Graham Davey

"Ultrafine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The recent development of industrially proven and cost efficient technologies for ultrafine grinding has opened up another processing option for the treatment of finegrained metalliferous and refractory gold ores. The current commercial designs are variations of stirred mills used in the industrial minerals sector for the past 30 years. For the purposes of this paper ultrafine grinding is considered to be P80 of less than 15 microns.Attrition milling to fine grind sizes presents some challenging issues relating to scale-up including the dearth of information on the quantitative impact of feed and operating conditions, as well as the precise and accurate measurement of particle size distributions. Two examples from recent installations will be analyzed including Thalanga Copper and Century Zinc Mines. Both have diverse grind size targets for the SMD, yet both have realized significant metallurgical gains."

Jan 1, 2002

By Y Zhuang, S La Brooy

The selection of the optimum process route for a new project has traditionally consisted of investigating existing options and ranking them in terms of cost, technical risk and environmental acceptability. With the current focus on sustainable development other factors now need to be considered. Life Cycle Assessment (LCA) of the process options can be used to extend the assessment in terms of their potential for earning renewable energy credits and in judging their ability to achieve greenhouse gas emission reductions. A rigorous life cycle assessment is demanding in terms of setting the baseline for comparisons and evaluating the elements that make up the emission profiles of the process options. However, a simplified LCA can provide a useful tool for comparing different process options. This approach can be combined with traditional assessment criteria to rank the options available to the project. GRD Minproc has been intimately involved in executing LCA calculations for different municipal waste treatment options. This paper applies a similar LCA methodology to investigate the greenhouse gas implications for different options for copper processing. The process options considered are:concentrator û sale of concentrate to smelter, concentrator û on-site mini smelter, and concentrator û leach SX/EW. The paper then goes on to consider the operating cost implications that could arise with the introduction of carbon taxes or carbon credits and how these might impact on the future choice of flowsheet.

Jan 1, 2002

By J L. Mauk

The Favona low-sulfidation epithermal deposit in the Hauraki Goldfield is less than one kilometre southeast of the world-class Waihi deposit. The veins are hosted by Miocene andesite of the Waipupu Formation, have a total strike length of over 900 m, a vertical extent of at least 350 m and are on average 1-3 m wide. Individual veins have been traced for 200 m with vein widths up to 25 m. The dominant vein textures are massive, crustiform and colloform banded veins and vein breccias, with subsidiary textures including comb, zonal, flamboyant, lattice-bladed, ghost-bladed, microbotryoidal, feathery, ripple and dune, and mosaic. Quartz is the dominant gangue mineral in the veins at Favona. Accessory gangue minerals include pyrite, chlorite, adularia, illite, calcite, and apatite. Electrum is the only gold-bearing mineral and is associated with acanthite, tetrahedrite, pyrite, sphalerite, chalcopyrite, and rare galena. Whole rock geochemical analyses indicate that gold grades correlate with textures/vein types. The highest gold and silver grades are associated with vein breccias and banded veins, with the former containing 28 g/t Au and 136 g/t Ag on average. To date, veins with significant base metal sulfide minerals, and massive and crystalline quartz veins lack significant precious metals (Au and Ag), except for one banded base metal sulfide-rich vein at Favona. An overall zonation of the veins exists, with base metal sulfide minerals dominant at depth (1050 m RL) of the system are characterised by massive quartz veins.Fluid inclusions from a total of 31 quartz, amethyst, and platy calcite veins reveal homogenisation temperatures of ~190-250¦C, with final ice melting temperatures between 0.0 and -0.8. Ice melting temperatures correspond to apparent salinities of 18O value of the water that formed these veins is approximately -4.3 per mil, which is similar to meteoric water-dominated, near neutral chloride fluids in geothermal systems in the Taupo Volcanic Zone.

Jan 1, 2002

By D. D. Tannant

An experimental and numerical study was conducted on the geomechanical behaviour of oil sands during penetration tests in which a steel wedge with an apex angle of either 20 degrees or 30 degrees was forced into compacted oil sands. The boundary conditions simulated in the laboratory tests are similar to shovel penetration into oil sands. The objective of the laboratory tests was to measure the force required to push a steel wedge into compacted oil sands. A wedge penetration test differs from conventional triaxial tests in that much more shear is generated. The laboratory data was needed to improve calibration of micro-mechanical input parameters for a two-dimensional discrete element model of oil sands constructed with Particle Flow Code (PFC). Initial model calibration was performed with triaxial test data and then a PFC model of the wedge penetration test was constructed. The measured force-displacement behaviour of the steel wedge was compared with PFC modelling results. It was found that different combinations of PFC particle and bond parameters could equally well replicate the laboratory triaxial compression data for bitumen-rich oil sands. When the wedge model was run, it was found that the resulting force required to penetrate the wedge into the oil sands was about four to six times higher than that measured. This clearly indicates that further research is required to improve the predictive capability of PFC models of oil sands.

Jan 1, 2002

By S. A. Osterberg, J. L. Breckenridge, R. S. Popielak

Multidisciplinary investigations were completed to prove the availability of water resources for the proposed San Cristóbal silver-lead-zinc mine in the arid Altiplano of Bolivia. Surface water resources are scarce, of poor quality, and unsuitable for development. Therefore, hydrogeological reconnaissance targeted alluvial aquifers for development. Follow-up resistivity, refraction, and water quality assessments were used to prioritize areas with prolific production potential. Pumping tests and regional water balance analysis indicate an alluvial aquifer can sustain the required approximately 40 000 m3 per day production for the life of the mine and predict no significant negative environmental effects on local groundwater users and the environment.

Jan 1, 2002