Search Documents

By James W. Weaver

The 2,120-foot long cable stayed Penobscot Narrows Bridge that carries US Route 1 over the Penobscot River between Verona Island and Prospect, Maine is supported on four foundation units, one below each pylon and one at each abutment. Due to varying subsurface conditions along the bridge alignment, the structure was designed to be supported on foundations consisting of high-capacity steel H-section piles (Verona Pylon), a mat bearing on a prepared bedrock surface (Prospect Pylon) and spread footings bearing on compacted rockfill (abutments). The 70-foot by 80-foot (plan area) Verona Pylon foundation was designed to be supported by 288, 430-kip design capacity steel H-section piles (HP14x117, 50 ksi steel) driven through up to 100 feet of dense glacial till deposits containing cobbles and boulders up to 3 feet in diameter. The piles were installed using a single-acting diesel hammer (Delmag D62-22) with a maximum rated energy of 165 kip-ft. Thirteen representative piles were selected for dynamic testing (ASTM D-4945) to verify pile capacity, hammer efficiency and pile stresses. Dynamic testing determined that four different pile driving criteria were needed across the site due to variation in the bedrock and soil resistance below the footing plan area. Approximately 4 percent of the production piles were damaged/rejected due to misalignment and/or damage as a result of encountering the cobbles and boulders embedded in the glacial till. The rejected piles were located randomly throughout the plan limits of the foundation mat. Subsequent structural analyses indicated that the foundation was capable of safely supporting the design loads without the need for installing replacement piles. Evaluation of dynamic testing results with signal matching and pile driving records provided valuable information on pile side and tip resistance. Evaluations were made regarding predicted versus actual pile lengths, pile bearing material, distribution of skin friction and end bearing capacities.

Jan 1, 2011

By J. N. Van der Merwe

The current state of the South African mining industry is briefly reviewed from the point of view of an engineer not schooled in the finer details of predictive economics. Based on the assumption that current world exploration targets are indicative of which commodities the world will want in the future, it is concluded that the South African mining industry will continue to be viable and growing well into the future. South Africa holds the minerals the world wants and needs, and as long as the world has people, the demand for those, including gold, will continue to grow. There still is a growing demand for vanity commodities' and even the demand for platinum as a jewellery material displays significant growth. Mine safety still needs to improve, but significant improvement has already been made although the industry is not always acknowledged for the effort in this field. The safety target set for 2013 is within reach but will require sustained effort. The physical mining conditions for the main revenue earners, coal, platinum, and gold, will change substantially in the near future. Research in mining has declined alarmingly and it is urgently necessary for that to be revitalized to generate the knowledge that will be required. In order to streamline the transfer of knowledge to the mining engineers of the future, research needs to be conducted with the full involvement of the universities. It will also be necessary for the universities to continually review curricula to incorporate the latest knowledge and to embark on a campaign of knowledge transfer to the older generation of mining engineers. The mining industry is well supported by the universities, who have done their duty with regard to societal transformation, and the universities are in turn supported by the industry through vehicles like the METE Industry is also strongly supported by a number of professional and vocational societies. The SAIMM will continue to play its vital role as the meeting point of the mining technical sciences, and will continue to disseminate knowledge via the journal, schools, and conferences. In the future, it will review its modus operandi to support the needs of growing membership in the remote branches. It will enter the research arena in an appropriate manner and give effect to the developing integration of mining and society. The most important threat to the future of the mining industry is the recurrent mention of nationalization. While interaction between the mining industry and political and economic development of South Africa has always been characteristic, the current debate is emotional more than rational, and engineers are not well equipped to participate. This matter needs to be finalized before it becomes a popular force that politicians cannot control.

Jan 1, 2011

By J. Kretschmann

?We have constructed a world in which the potential for high-tech catastrophe is embedded in the fabric of day-to-day life.? (Malcolm Gladwell) The mining industry is a crucial provider for virtually every person?s needs and thus indispensable. Yet, mining is a complex and risky business: plenty of high risk factors can occur and severely affect nature and the miner?s life and health. Especially for small and medium enterprises (SME) risks may also threaten the economic existence of the company. The responsible and sustainable management of a company should thus be based upon the systematic finding and handling of risks or briefly upon an efficient risk management system. Why do we need risk management? Because nobody is perfect and we make mistakes in the normal course of operation.

Jan 1, 2011

By K. C. Mills

The objective of this work was to provide process engineers with values of the physical properties of various slag systems involved in high-temperature processes. Software that calculates the thermo-physical properties of slags from chemical composition is available on the www.pyrometallurgy.co.za website. This paper outlines the principles underlying the various models available in the program. The software calculates the following properties of crystalline, glassy, and liquid slags (where appropriate) as a function of temperature: heat capacity, enthalpy, density, viscosity, thermal conductivity, electrical conductivity, and surface tension. We hope, in the future, to update the program to (i) add new models as they become available, (ii) remove any ?bugs? discovered in existing programs, and (iii) provide guidance on the limitations of individual programs.

Jan 1, 2011

To build an effective entry roof beam, a roof bolting or supporting system must be of the ability of providing a clamping force to the bolted roof strata. Currently, two roof bolting systems are widely used to serve the purpose of providing such a clamping force. They are resin and mechanical anchorage bolting systems. Both numerical modeling and double shear testing results indicate that a greater pre-installed load or pretension of a roof bolting system is very critical for effective beam building. Although it?s generally accepted that a mechanical anchorage bolting system can provide a greater pretension than a resin anchorage bolting system does (Su and Poland, 2007 and Peng, 2008), no published field data are available to support such a conclusion. This paper analyzes the results of our field tests on both roof bolting systems, explains why one roof bolting system is better than the other under a typical roof condition, and finally discusses the effective means for coal mine operators to determine the best roof bolting system for their roof conditions.

Jan 1, 2011

By J. W. Langford

A more effective method of fracturing and chipping the formation is necessary to significantly increase the productivity of blasthole drilling with a roller cone bit. The conventional rotary blasthole bit engages the formation and initiates spalls, chipping and fractures in the formation at a rate dependent on the amount of pull down force applied by the drill. The rotary speed of the drill increases the number of fractures and creates drilled chips that are removed from the hole by the air circulation. An engineering project was motivated to develop a low pressure, low impact downhole percussion hammer to provide an overstrike force to a blasthole bit, in addition to the conventional pull down force and rotary speed. The objective of the project was to utilize existing rig air packages in the range of 50-110 psig and provide an overstrike force to the bit in the range of 1100-1500 impacts per minute. Laboratory testing performed on Barre granite achieved, on average, a 40% improvement in rate of penetration. This performance has been confirmed in actual blasthole drilling in copper and iron ores mines. During the testing phase, additional unexpected benefits have also been realized.

Jan 1, 2011

By R. Degel

Keywords: Pyrometallurgy, DC furnaces, electric smelter, FeCr, FeNi, FeMn, Si metal, ferro-alloys, platinum production, circular furnace, energy recovery system In 1906, the first submerged-arc furnace was supplied by SMS Siemag. Since then, the division has become established in various industries such as ferro-alloys and non-ferrous metals, and in numerous other special applications. During the evolution of this technology, more efficient units with longer lifetimes were developed. Today, especially the potential of DC-based smelters, raises worldwide attention, with some projects having already started to implement this kind of technology. This paper evaluates SMS Siemag?s general viewpoint regarding the potential application of DC smelter technology and possible options for the ferro-alloy and non-ferrous industry. SMS Siemag is currently executing a FeCr project in Kazakhstan, where four of the world?s largest closed-type DC smelting furnaces, with a power input of 72 MW, will be installed. These furnaces include the latest technological features of modern DC smelters, which are described in this paper. SMS Siemag has started a long-term research and development project allowing a direct comparison of AC versus DC technology on a large scale, using a recently installed 1 MVA test furnace at the IME at the University of Aachen, in Germany. For open-type ferro-alloy and Si-metal furnaces, SMS Siemag has developed an energy recovery system, which is presented in this paper.

Jan 1, 2011

By E. Lammer

"Underground mining processes are dangerous. The design of mining equipment, which is able to cope with the hostile underground environment, is a challenge for all machine manufacturers. Presupposition for realizing the vision of SANDVIK for zero harm for working with SANDVIK equipment is the installation of the appropriate processes. Into the product engineering and product development processes of Sandvik Mining and Construction, a specific "Product Safety Process" has been integrated, where all safety related activities like identification of all life cycle hazards, risk management and safety verification / validation are planned, performed and documented. Product safety shall be „designed into" the products. Therefore, specific research activities have been started, to address the safety and health related topics for the development and for the engineering of SANDVIK mining machines."

Jan 1, 2011

By F. S. A. de Frey

The author would like to refer to his contribution to the paper `Design of pillar systems in South Africa' by Ozbay et al. 1. The authors agreed `wholeheartedly that further research, together with carefully planned field trials, in pursuit of this potentially highly rewarding concept' of the small span small pillar method is warranted. On 30 September 2010 the author went underground at the Kroondal Chrome Mine to observe how the concept of smaller spans was being applied. He was pleasantly surprised to find that the typical coal mine bord and pillar sytem was being used very successfully. Although the deepest mining was taking place at a depth of only 450 metres, Kroondal would be an ideal mine to do further research together with carefully planned field trials. At Crown Mines Gold Mine, where the author worked, he was informed that the first recorded rockburst took place at a depth of 635 metres below surface. The depth of the platinum and chrome mines is increasing, with the risk of an excalation in injuries and fatalities due to 'backbreaks' and siesmic activity. The rock engineer at Kroondal was not aware of backbreaks occuring on the mine. It is important that the rock engineers of the base mineral and gold mines get together and give more serious attention to the host rock environment in which the pillars are situated.

Jan 1, 2011

By P. Leo

The Al-Zn-Mg alloys (e.g. 7004, 7020) are employed for land transport and architectural applications whereas the Al-Zn-Mg-Cu alloys (e.g. 7075, 7050) provide the high strength aircraft alloys. The Cu gives rise to suitably sized and distributed precipitation but causes high quench sensitivity. Their hot work processing also has marked differences; the Cu-free alloys have good extrudability whereas the Cu-bearing alloys have low extrudability and are difficult in rolling as well. The behaviors of the two classes are described in terms of flow stresses and ductility over 300 - 500°C, along with constitutive contrasts. The ductility of the alloys with Cu is much reduced above 400°C by precipitation of a phase at the grain boundaries that can be avoided by suitable heating schedules. The high strength alloys are subject to de-lamination corrosion of sheared edges due to severely pancaked grains; this can be alleviated by holding between passes, in mid-rolling schedule. In torsion tests at 10-1 to 10 s-1/ 250 - 500°C, the stresses (ductilities) at 300°C/ 1s-1 and activation energy Q for 7004 were 118 MPa (2) and 262 kJ/mol. The 7075 was tested after several pretreatments: completely over-aged (softened): 107 MPa (5), Q=150 kJ/mol; whereas, solution and quick cooling to testing caused extraordinarily high peaks related to dynamic precipitation resulting in 160 MPa (1.2), Q=300 kJ/mol.

Jan 1, 2011

Nuclear power currently produces about 20% of the electricity in the US, with 104 nuclear power plants located in 31 states. The commercial US nuclear industry contributes over $4 billion annually to US workers in salaries and wages. 25,000 new jobs need to be filled in the next 5 years. There are over 30 new power plants under consideration by US utilities. The operating reactors use uranium oxide fuel enriched to about 4% U235 and fission is the process used to generate heat to form steam to drive the turbine generators. Nuclear energy is an important element in the US generation portfolio and represents the largest producer of nearly emission-free electricity. Most, if not all, of the operating plants will secure an extended 20 years of operation or more. The last plant constructed was ordered in 1978. New smaller, modular reactors are under design to provide less expensive, expandable generation options.

Jan 1, 2011

By R. T. Jones

DC arc furnaces are widely used for steel scrap melting as well as for reductive smelting of ore fines. Industrial smelting applications include the smelting of chromite to produce ferrochromium, the smelting of ilmenite to produce titania slag and pig iron, and the recovery of cobalt from nonferrous smelter slags. A number of myths and misconceptions are widely held, especially regarding: the age of the technology, the use of a hollow electrode, arc stability and shape, arc and bath radiation, interaction between the arc and molten slag, electrical behaviour of arcs and slags, a comparison between AC and DC furnaces, DC reactors, the lifespan of bottom electrodes, and the applicability of DC arc furnaces to various metallurgical systems.

Jan 1, 2011

By Gregory Abramov

Borehole Mining (BHM), a remotely-operated waterjet mining method (Figure 1), has recently achieved two major milestones. It was, for the first time, applied to the extraction of manganese ore and at temperatures below freezing. The 1St stage is a demonstration test that is now underway just north of Emily, Minnesota, where the manganese ore is located 100-160m below the surface and its reserves are estimated to be in excess of 500,000 tons. The deposit was discovered over 60 years ago but, due to the fragile and sensitive nature of this Land of 10,000 Lakes (nickname for the State of Minnesota) and strong environmental restrictions, the iron/manganese reserves were deemed unrecoverable and remained untouched until late 2010 when permission for a single-hole demo-test was issued by the local Department of Natural Resources.

Jan 1, 2011

By Dimitris Pachakis

In this paper, the authors give a brief overview of the current practice guidelines and tools for the seismic design of sheet pile quay walls, emphasizing how the design guidelines are lacking when the existing structure performance evaluation is required to meet performance-based criteria. Relying on recent experience they explain how the existing practices can be amended to focus more on performance evaluation as opposed to design. An example is given of an old sheet pile quay wall analyzed and evaluated for its performance according the recent performance criteria devised for Californian Marine Oil Terminals.

Jan 1, 2011

By Jr. Blanchette, Claude Bazin, Paul Blatter

"Reporting of the gold production during a month implies to estimate the mass of gold that is processed by a mill, recovered as dorés, lost to the tailings and the change of gold inventory within the plant equipments. Carbon in pulp and/or carbon in leach tanks may contain gold inventory as large as 72 000 g (2 200 troy oz) of gold which needs to be estimated from measurements obtained from sampling the material contained in a tank. Sampling and analysis introduce measurement errors that could be systematic and/or random. This paper examines the effect of measurement errors on the estimation of the gold inventory and on the variation of the inventory in the carbon in leach tanks of the Agnico-Eagle Mines Limited Lapa concentrator. Results of the analysis demonstrate that the inventory is measured with ±10% reproducibility, while the variation of inventory used for mass balance is known with ±300% reproducibility.INTRODUCTIONThe preparation of a production report implies to reconcile measured data with the constraint of material balance over the considered period of production. The sampling and data reconciliation problems were recently reviewed by Morrison (2008) and Jansen (2009a; 2009b). Typically a production report is prepared to cover a period over which the mass conservation hypothesis can be considered valid. In gold processing plants, the change of inventory can seldom be neglected and plays a significant role in material balance calculations. This is particularly true for circuits using carbon adsorption, where the complete cycle of carbon is measured in days.In a 2000 t/d gold ore processing plant, the inventory can be as large as 140 000 g of gold in gravity concentrator bins, carbon in pulp tanks and in the electrolysis circuit. This is equivalent to the mass of gold that fed the circuit during 10 days of operation with 7 g/t feed assays. The change of inventory may therefore strongly impact the production figures and especially the plant recovery at the end of a week or a month. Despite the financial impact associated with gold inventory, few publications are devoted to the subject. Bruington (1991) and Morrison (2008) discussed the problem and stressed the need for the development of reliable methods to estimate the gold inventory in carbon in pulp or carbon in leach circuits."

Jan 1, 2011

By Q. G. Reynolds

Keywords: Pyrometallurgy, furnace, DC, reverse polarity, dual-electrode The dual-electrode direct current (DC) arc furnace uses two graphite electrodes, one connected as cathode, and one as anode. Such an arrangement avoids some of the design difficulties associated with the anode hearth traditionally used in single electrode and twin-cathode DC furnaces, but can introduce other design and operational difficulties including deflection of the arcs toward the furnace walls. Counter-intuitively, both arc jets in a dual-electrode furnace travel from the electrode down to the bath surface, despite carrying electric current in opposite directions ? this is suggested in the theory of the governing equations of arc formation, and confirmed by experiments using high-speed photography. The dual-electrode arc system at small pilot-plant scale is studied using a transient magneto-hydrodynamic model capable of predicting arc deflection and interaction from first principles, and the results are compared to the behaviour of twin-cathode systems at similar power. Finally, a simple arrangement of the furnace busbars, M configuration, is shown to provide some passive protection against arc deflection.

Jan 1, 2011

By C. Machio

This paper reports the results of a study to determine the effect of process control agent (PCA) on the characteristics of Ti-Mg powders during milling. It has been shown that a 2% increase in PCA content leads to up to a 40% increase in yield of the milled powder but reduces the kinetics of the mechanical alloying process. The introduction of 4% PCA decreases the mean powder particle size by up to 30%, whereas 6% PCA increases the mean particle size by up to 230%. The characteristics of the milled powders will be discussed in relation to the role of PCA in the milling process. Keywords Titanium?magnesium, mechanical alloying, PCA.

Jan 1, 2011

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The Forestry Reclamation Approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22-m (4-ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes could lead to slope failures, which is one of the issues that SMCRA sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. There has been no major mass movement of the slope and slope stability analyses indicate that the application of the FRA has little impact on the overall stability of the slope.

Jan 1, 2011

By S. L. George

The semi-solid metal casting process results in a unique solidification path. The microstructural features that were identified during the characterization of the as-cast microstructure, were used as evidence of the process history in order to determine the solidification path followed during the evolution of the microstructure. The morphology of the grains was characterized using SEM and the extent and distribution of the elemental segregation within the grain structure was analysed using EDS. Keywords Semi-solid casting, solidification path, segregation.

Jan 1, 2011

By R Yang, M Lownds

This paper reports studies showing the effects of delay scatter on the peak particle velocity (PPV) of blast vibration using a multiple seed wave (MSW) vibration model developed in recent years. The case studies also show the advantage of accurate delay timing on frequency control of blast vibration. The site parameters used in one of the studies are from a case in which the MSW model has been tested and confirmed to yield accurate predictions. This study uses an open pit blast design and a tunnel design in which blast vibrations using electronic detonators are compared with those from pyrotechnic detonators. Mean peak particle velocity (PPV) and the 97.5% upper bound PPV are compared. It is found that both these values increase significantly with the increase of the coefficient of variation of the site parameter. Using an open pit blast design, the modeling shows that electronic initiation shifts vibration energy to the expected frequency for a selected point of interest. However, for the same design of nominal initiation timing pyrotechnic detonators fail to shift vibration to the expected frequency due to its large scatter of timing.

Jan 1, 2011