Search Documents

By F. H. McDowell

The increasing interest in the subject of electrical separation warrants the addition to what has already been written of a few lines covering the practical workings of the Tilly Foster mill under the direction of Mr. E. S. Moffat, General Manager. Since my last paper was presented to the Institute, Mr. S. P. Tomkins, the superintendent, has had thrust upon him for solution several problems complicated by the introduction of new conditions. 1. The richer portion of the lean ore dump, and that nearest the railroad track, having been worked up in 1890, the handling of the balance, including a largely increased amount of rock, could only be accomplished at an increased cost. 2. The tailings had accumulated close about the mill to such an extent that arrangements had to be perfected to move them further away.

Jan 1, 1893

By D. H. Bacon

Our Transactions contain so many suggestions of apparently trivial, yet really important, contrivances for the saving of time and

Jan 1, 1893

By John E. Lens

Minutes after the Friday afternoon October 16, 2009 announcement that the 80 year old Lake Champlain Bridge was closed to traffic out of concern for public safety, emergency detour planning started at VTrans and NYSDoT. The closure severed a cross-lake link between Addison, VT and Crown Point, NY, which created a 76 mile detour and significant hardship for commuters, farmers working on both sides of Lake Champlain, and businesses relying on both traffic and employees commuting between Vermont and New York. Rehabilitating the bridge was determined to be economically and technically unfeasible and the design of a replacement bridge was accelerated for a spring 2010 construction start. In the meantime, a temporary ferry alternative was to be rushed into service beside the original bridge by February 2, 2010. This paper presents the case history of the fast-tracked ferry dock design and construction on the Vermont side. Twin 300-foot-long pile supported approach spans, a loading slip system and ice deflectors were designed, fabricated and constructed in 90 days in the fall/winter of 2009-2010. This chronicles the project from initial concepts through the extraordinary cooperation between state and federal agencies, and near round-the-clock winter construction on Lake Champlain. This project and its companion project on the New York shore succeeded by virtue of exceptional cooperation between seasoned regulatory, design, and construction participants and warrant this case-history presentation of the Vermont project to share within the industry as an example of overcoming extraordinary challenges.

Jan 1, 2011

By D Johnston

Within the first full year of BarrickÆs Cowal Gold Mine operation, the Lake Cowal Foundation Limited (LCF) has already been delivering results consistent with its goal to protect and enhance the natural environment of Lake Cowal and its catchment area. The LCF is a non-profit Environmental Trust established in June 2000 in conjunction with the development consent process for the construction of BarrickÆs Cowal Gold Mine. Its primary goal is to protect and enhance Lake Cowal, a nationally significant ephemeral wetland located 350 km west of Sydney, New South Wales, Australia. Significant concentrations of water birds visit the lake and the Australian Heritage Commission listed Lake Cowal on the Register of the National Estate in 1992. The LCF is managed by a Board of Directors from representative member organisations including the Total Environment Centre, National Parks Association, Nature Conservation Council and Barrick Australia Limited. Although largely funded by Barrick, the Foundation also attracts external funding and works in partnership with a diverse range of other groups and organisations, beyond the mine fence. The total value of currently approved projects is estimated to be in excess of $7.1 million, which includes æin-kindÆ contributions made by the local community and in particular the Lachlan Catchment Management Authority (LCMA) and local farmers. To date, LCF has been involved with the development and implementation of 30 projects with a total of 34 project partners. LCF has worked with over 60 landholders to improve Lake Cowal and its catchment, with 6180 ha of land now being managed for conservation or sustainable farming in the local area. Many landholders have been, or are involved in property planning or participating in other training opportunities. Sustainability of LCF programs and outcomes will be assured by commitments to projects within four key themes: conservation, research and research support, sustainable farming and community education and training. The LCF works independently from the mining company and has no responsibility for the environmental management within the mining lease. It is about capitalising resources generated by the mine to enhance environmental outcomes in the wider Lake Cowal catchment area by working collaboratively with the local community, industry and government authorities to ensure the long-term protection of a unique wetland ecosystem affected by landscape scale degradation.

Jan 1, 2007

By Timothy M. Bruner, William J. Maloney

Faced with rapid growth that strained their current water supply capabilities, the Somerset Water Service in Somerset, KY decided to construct a new intake structure on the shore of Lake Cumberland. With an existing intake structure within 200', very hard limestone geology with calcite geodes, and lake level fluctuations as high as 50 ' ,this project posed many challenges. The following paper discusses how mechanical excavation techniques were used to overcome these obstacles.

Jan 1, 2001

By Jason Morrison

The Norwegian Lake Tap Method was successfully used to tap into the side of Lake Dorothy 36.5 m (120') below the lake surface. The lake tap allows water to flowinto an access tunnel from the lake lowering the water elevation below its natural out-fall. When the lake reaches a predetermined elevation below the outfall, a 1.5 m (60?) valve in the tunnel will be shut and discharge from Lake Dorothy will stop temporarily allowing construction of a dam located 2.9 km (1.8 miles) downstream at Bart Lake. The lake tap and tunnel were one phase of the $64 million Lake Dorothy Hydroelectric Project, owned and operated by Alaska Electric Light & Power Company (AEL&P), a private utility located in Juneau, AK. The Lake Dorothy portal site and tunnel are located approximately 25.7 km (16 miles) southeast of Juneau, AK, in the remote Tongass National Forest at an elevation of 701 m (2,300') above sea level in the mountains above the Taku Inlet. Thirty degree snow covered mountainsides and limited access by helicopter were just two of the many factors which challenged this unique project. The lake tap and tunnel development consisted of 250 m (820') of horizontal tun-nel, averaging 3.6 m x 3.6 m (12' × 12'), excavated using conventional drill and blast methods in highly competent Granodiorite and Tonalite rock, placement of one 3.9 m (13') long concrete plug, or bulkhead, located at the tunnel midpoint, and one 3 m (10') diameter lake tap into the side of Lake Dorothy. This paper will provide an analysis of the logistical and engineering challenges involved in the development of one of only a handful of lake taps in North America. AEL&P and contractor J. S. Redpath Corporation worked together to complete this critical project phase safely and on schedule, in a location accessible only by helicopter and plagued by constantly changing, harsh weather conditions. A strict schedule had to be maintained to ensure the timely operation of the downstream dam and power plant.

By Roberto J. Guardia, Ted Lewtas, Peter Rasmussen, Klaus Winkler

As part of the Lake Fort Smith Water Supply Dam Enlargement project, located in northwest Arkansas, microtunneling methods were used to install two side-by-side,1.53m (60-in) inside-diameter steel pipes between the intake structure shaft and the lake. The 46.6 m- (153 ft-) and 41.7 m- (137 ft-) long tunnels were excavated in Pennsylvanian sedimentary bedrock ranging from coarse sandstone to siltstone and shale-like claystone. The intake tunnels were constructed 18.3 m (60 ft) below lake level from the dry shaft. Special installation methods and procedures described herein were used to complete the lake taps. Installation difficulties that caused minor delays are also reviewed. After the excavation of the Intake shaft was completed, the two lake taps were installed in approximately ten weeks with the same microtunneling machine.

Jan 1, 2005

By R. V. Norris

In a former paper on this subject,' I summarized Murgue's theory and experiments, and presented a large number of tests of mine-fans, stating some conclusions, " more or less warranted by the evidence," as to design, capacity and efficiency. Since that time the very valuable report of Mr. M. Walton Brown: Committee on Mechanical Ventikators, Institution of Mining Engineers, has appeared, and I have made additional experiments which tend to clear up some points in connection with this subject. Design and Tests of the Luke-Fidlbr Colliery Fan. The Luke-Fidler fan (see Figs. 1, 2 and 3), built to replace an old wooden fan at a very fiery colliery, presents some pecu-

Jan 1, 1905

By C. J. Hicks

The labor policy of the Standard Oil Co. (New Jersey) is founded first of all on paying at least the prevailing scale of wages for similar work in the community; on the eight-hour day at the refinery, with time and one-half for overtime; one day's rest in seven; sanitary and up-to-date working conditions; just treatment assured each employee; opportunity for training and advancement; payment of accident benefits beyond the amount prescribed by the State compensation law; health supervision by a competent medical staff; payment of sickness benefits after one year's service; coöperation with employees in promoting thrift and better social and housing. conditions; and assurance of a generous annuity at the age of 65, guaranteed for life after 20 years of service. Most of these features have been a part of the company's policy for many years, but it is only during the past two years that the cooperation of employees in determining these matters has been definitely assured through industrial representation. Industrial representation, in the Standard Oil Co. (N. J.), is a principle rather than a procedure. It is built upon the belief that personal association of those interested in any problem leads to a mutual understanding and a fair decision as to what is right. Fully believing in this principle, representatives of employees and representatives of management evolved a simple plan, the basis of which is that it gives every individual employee representation at joint conferences on problems and fundamental principles affecting all those interested in the industry. It is based on cooperation, not antagonism; its operation makes perfectly clear both to management and to employees that their interests are identical, and not at variance with the interests of the stockholders, and that mutual understanding and cooperation insure progress and success for all. Furthermore, experience has definitely shown that representatives of the employees are not only alert for the employees' interests but are as keen as the representatives of the management in determining and insisting upon fairness to the employer. Though the plan has been in operation nearly two years, it is an experiment, in that, being based on a principle rather than on cut-and-

Jan 1, 1921

By H. E. Wheeler

The work described was carried out during 1917 and 1918 at the testing laboratory of Watertown Arsenal at the instigation of the Nitrate Division and later with the concurrence of the Cannon Section of the Ordnance Department, U. 8. A. The experiments follow three principal lines of work: First, the effect of nitrogen under pressure on steel containers of various compositions at a red heat; second, the effect of decomposing ammonia on various alloy steels, iron, and non-ferrous alloys; third, a new theory of the erosion of guns in respect to the effect of nitrogen in steel. Part I In the Haber process for the manufacture of ammonia from its elcnlents, it is necessary to have nitrogen and hydrogen of 1500 lb. per sq. in. (105.5 kg. per sq. cm.) at a temperature of 500 to 600' C. The steel containers for these gases gave trouble by failing without apparent cause. When the General Chemical Co. began to develop its method for the production of ammonia, it experienced the same difficulty and, knowing that the Haber process had solved the difficulty by the use of alloy steels, it made several small steel bottles of different compositions and kept them filled with these gases at this pressure and temperature until they failed. The time of service varied from a few days, for the plain steel casting, to two years for a chrome-vanadium forging. Four of these steel bottles were sent to this laboratory for investigation; they were a plain carbon-steel forging, a nickel-stee1 forging, a chrome-vanadium steel forging, and a chrome-steel forging. The time of service was as follows: plain carbon steel, 4 mo.; nickel steel, 6 mo.; chrome-vanadium steel, over 2 yr.; chrome steel, 4 mo. When these containers were cut open and the cross-section surface polished, they showed an inside zone with a different luster from the rest of the metal. Upon etching, this zone was almost unaffected while the rest of the steel etched normally.

Jan 1, 1922

By H. E. Wheeler

The work described was carried out during 1917 and 1918 at the testing laboratory of Watertown Arsenal at the instigation of the Nitrate Division and later with the concurrence of the Cannon Section of the Ordnance Department, U. 8. A. The experiments follow three principal lines of work: First, the effect of nitrogen under pressure on steel containers of various compositions at a red heat; second, the effect of decomposing ammonia on various alloy steels, iron, and non-ferrous alloys; third, a new theory of the erosion of guns in respect to the effect of nitrogen in steel. Part I In the Haber process for the manufacture of ammonia from its elcnlents, it is necessary to have nitrogen and hydrogen of 1500 lb. per sq. in. (105.5 kg. per sq. cm.) at a temperature of 500 to 600' C. The steel containers for these gases gave trouble by failing without apparent cause. When the General Chemical Co. began to develop its method for the production of ammonia, it experienced the same difficulty and, knowing that the Haber process had solved the difficulty by the use of alloy steels, it made several small steel bottles of different compositions and kept them filled with these gases at this pressure and temperature until they failed. The time of service varied from a few days, for the plain steel casting, to two years for a chrome-vanadium forging. Four of these steel bottles were sent to this laboratory for investigation; they were a plain carbon-steel forging, a nickel-stee1 forging, a chrome-vanadium steel forging, and a chrome-steel forging. The time of service was as follows: plain carbon steel, 4 mo.; nickel steel, 6 mo.; chrome-vanadium steel, over 2 yr.; chrome steel, 4 mo. When these containers were cut open and the cross-section surface polished, they showed an inside zone with a different luster from the rest of the metal. Upon etching, this zone was almost unaffected while the rest of the steel etched normally.

Jan 1, 1922

By W. R. Crane

While professiorlally engaged in the oil- and gas-fields of Kansas, in measuring the pressure and flow of gas-wells, and studying the phenomena attendant upon the production of both oil and gas, I noticed in the flow of gas a peculiar and interesting feature. That there are actual lines of flow in liquids (non-compressible fluids) discharged through an orifice, or a short section of pipe, is shown by the external shape of the discharge—the vena contracts. Such lines of flow are not observable in the discharge of gas from an orifice. It can hardly be questioned that they exist. That they are not apparent is probably due to the very small weight of the gaseous particles, which climinishes the momentum of their movement in a given direction, acquired before they issue from the orifice, and also to the expansion of the gases, which would exert a powerful influence in overcoming any such tendency in their flow. Gas flowing from an orifice, supplied by a large reservoir or blowing-engine, exhibits almost the reverse of what is noticed with liquids. Namely, the gas assumes the form of an inverted truncated cone, of large angle: with its apex-end at the orifice. (See BB, Fig. 1.) This external ahape assunled by the flow of gas shows, however, marked differences under varying conditions of volume and pressure. For instance, a large volume of gas under high pressure, flowing through a 2- or 3-in. pipe, as in the case of a natural gas-well, assumes a more definite conical form, the angle of which increases as the pressure falls. Moreover, outside of the well-defined inverted cone is a thin conical heath or zone of gas, A A, the angle of which is considerably greater than that of the main cone, and increases with +1UNIVERSITY OF KANSAS, LAWRENCE, KANSAS.

Jan 1, 1905

By James Gayley

The atmosphere, which plays such an important part in the manufacture of iron and steel, is the most variable element involved in its several processes; and particularly is this true of the blast-furnace process, which consumes air in large quantitiee. At no time since the blast-furnace became an important and widely used apparatus—even when it was operated in the most crude manner—have the variations in composition of the raw materials used been as frequent and as great as the variations in humidity of the atmosphere. Important improvements have been made in the blast-furnace and its accessories, such as the hot-blast stoves, the increase in size and change in the shape of the furnace, more efficient blowing-engines, the increased protection given to the bosh-walls, and the careful preparation of the raw material, all of which have exerted a pronounced influence on the furnace-operations from a metallurgical standpoint. But during the past eight years little advance has been made in this direction; the fuel-consumption has not diminished, nor has there been any material increase in production. Within that period, however, there has been witnessed the greatest development in appliances for the economical handling of material. So complete has been the work in this direction, that, except in isolated cases, in this country at least, a further extension does not hold out much promise of a satisfactory return on the investment required. It seemed that, with the exception of the gas-engine, we had about reached the limit, for like a strong wall, the atmosphere, with its humidity as variable to-day as when first blown into a primitive blast-furnace, appeared to stand as a barrier to

Jan 1, 1905

By Charles H. Morgan

Jan 1, 1905

By H. A. Guess

For a number of years I have used for the commercial wet assay of lead generally the ammonium molydate, and occa-sionally the ferrocyanide method. These well-known methods need no detailed description here. In the ore-selling and ore-buying establiahments of the West, 90 per cent. of all wet lead-assays are made by one or the other, and at least nine-tenths of this proportion by the molybdate method. A procedure so well-established must have merit; and, in

Jan 1, 1905

By Myrick N. Bolles

The concentration of gold and silver in mattes low in copper, and the subsequent separation and recovery of either or both of these metals, is a question the satisfactory solution of which has long vexed metallurgists. It covers a broad and important department of metallurgical science and brings in its train a series of attendant problems continuing from the initial operations of concentration to the final recovery of " values."

Jan 1, 1905

By H. H. Campbell

Many attempts have been made to write a formula by which to calculate the strength of steel from its chemical composition, but most of these endeavors have failed because there were too many disturbing conditions. It is idle to collect from the pages of trade-papers, books, or the proceedings of scientific societies, a multitude of observations. The combination of such results will simply show that steel of the same composition will vary in tensile strength through wide limits—a fact that has been known for generations. That cold-working, overheating, and many another form of heat-treatment alter fundamentally the strength of steel, is ancient history, although it is only recently that the microscope has pointed out the road to an explanation of the phenomena. It mag be urged that the microscopic structure must betaken into consideration in any formula giving the ultimate strength, but from the standpoint of the present investigation this is unnecessary. We are trying to determine primarily, not what changes in ultimate strength may be made by variations in the condition of carbon, but what effect is produced by changes in the amount of carbon, when its condition remains constant. For such an inquiry, in order that the condition of the carbon should remain as nearly uniform as possible, it is essential that all testrpieces be made under the same conditions; and it is believed that the tests described in this paper satisfy that requirement. The investigations were made at the works of the Pennsylvania Steel Company, Steelton, Pa.; the ingots from which the tests were made were 6 in. square in every case; they were heated in the same furnace and forged at the same ham-

Jan 1, 1905

By H. M. Chance

The Taviche district is about 12 miles from the town of Ocotlan in the State of Oaxaca, and about 250 miles south of the City of Mexico. Its altitude rises to something more than 5,000 ft.; and although within the tropics (latitude about 17° N.) the climate is mild and salubrious, neither excessively hot in summer nor cold in winter. The phrase, "perpetual spring," which has been applied to it, aptly describes the weather during my stay. Sugar-plantations, bananas and other tropical and semitropical fruits flourish in the valleys, while the hills

Jan 1, 1905

By Paul Wilkinson

From the earliest times, the principal component of mallplaster has been ordinary lime. Plaster-of-Paris has also been known from early times, but never used to any extent in the actual base-work of plastering-materials; it is generally used for finishing over the brown coat and for ornamental work. As an illustration of the antiquity of the use of gypsum-plaster for mortar, I find that the analysis of the exterior covering of the pyramid of Cheops, as made by Dr. Wallace, is almost identical

Jan 1, 1898

By Douglas M. Smith, G. A. Maki

"The initial development of the massive potash deposits of the prairie evaporite formation took place over a decade ending in 1970. The potash mining and refining facility near Rocanvi11e, Saskatchewan was the 1ast of ten mines to come into production during that era. This operation, known as Sylvite of Canada Ltd., was designed to produce 1. 2 million short tons per year of KCl product in granular, coarse, standard and special standard grades.In 1977 the parent company, Hudson Bay Mining and Smelting, sold the Sylvite property to the Potash Corporation of Saskatchewan. Shortly thereafter PCS slated its new Rocanville Division for a two phase program of expansion. The first phase, completed in the spring of 1979, was relatively small, involving mill debottlenecking and additional equipment in the compaction circuit and the product and ore storage areas. The second phase was a major undertaking which included additional mining equipment and a new 300 STPH milling circuit. This work was completed during the fall of 1981 and has increased the Rocanville Division's nameplate capacity to two million STPY.Thickening equipment operating in the Saskatchewan potash industry is generally situated within the main refinery building or a separate insulated and heated structure due to the harsh winter climate and the need to closely control plant brine temperatures to ensure good flotation circuit performance. Since these thickeners process large volumes of slurries, conventional basin type designs tend to be large, ranging up to 150 feet in diameter or more. As part of the general effort to minimize capital costs, the potash industry has begun investigating the use of alternate high capacity, compact thickener designs. In this regard, PCS Rocanville undertook a program in 1978 to evaluate a Lamella™ Thickener and one other type of 'High Rate' thickener* as alternatives to a conventional design for the phase two expansion project."

Jan 1, 1983