Search Documents

By Abolfazl Eslami, Masoud Zare, Ali Asadi, Ali Abrang

"Physical small scale models for study of deep foundations can be performed in simple chambers (1g), calibration chambers (CC), and centrifuge apparatus (ng) which involve some limitations and difficulties. In recent years, Frustum confining vessels (FCV) have been developed for physical modeling of deep foundations. This device is frustum of a cone shape that applies a steady pressure on its bottom and creates a linear stress distribution along its vertical central line. A new FCV which has been built in AUT is introduced. This device has a height of 1200 mm, top and bottom diameters of 300 and 1300 mm, respectively. Through the application of bottom pressure up to 300 kPa, the insitu overburden stress conditions equivalent up to 40 m soil deposits consistent to the embedment depth of commonly used piles. Observation indicated that there is approximately a linear trend of stress distribution, and this device can create realistic overburden stress in the desired control volume along the central line. Moreover, a couple of compressive and tensile load tests were performed on steel tubular open end model piles driven in sand with length of 750 mm and different diameters and L/D ratio between 8-15. Comparison of load capacity between tested and full scale piles demonstrate a suitable conformity for similar confinement conditions. Therefore, the FCV can be realized as an appropriate apparatus for investigation of piling geotechnical behavior and examination of construction effects.IntroductionDeep foundations are designed as foundation system for supporting heavy loads, high rise and important structures. Different theoretical, numerical and experimental approaches have been developed to study the geotechnical behavior of deep foundations. Experimental methods are employed to clarify directly pile-soil interaction and because of repeatability, analogy, rapid measurement and cost efficiency, physical modeling can be realized as an intermediate technique compared to element testing and full scale load tests."

Jan 1, 2015

By Fred C. Delabbio

The successful implementation of a new technology in an underground production mine requires many challenges to be overcome. These challenges include mine hardening of new technology, mitigation of safety risks and hazards, mine operation support, and technology transfer to mine staff. In the end, the majority of these challenges relate to the human aspects of implementation. The approach selected to overcome these challenges must be customized and appropriate for each unique situation. This paper outlines the approach used to address these challenges as part of successful implementation and resulting demonstration of the hydrogen fuel cell locomotive at the Placer Dome (CLA) Limited, Campbell Mine. This technology demonstration at Campbell Mine is critical for determining technical, regulatory and implementation aspects to be incorporated into future fuel cell prototypes such as the LHD project.

May 1, 2003

By T. MacKinnon, M. C. Bétournay, D. Eastick, F. C. Delabbio, C. Graves

"The successful implementation of a new technology in an underground production mine requires many challenges to be overcome. These challenges include mine hardening of new technology, mitigation of safety risks and hazards, mine operation support, and technology transfer to mine staff. In the end, the majority of these challenges relate to the human aspects of implementation. The approach selected to overcome these challenges must be customized and appropriate for each unique situation.This paper outlines the approach used to address these challenges as part of successful implementation and resulting demonstration of the hydrogen fuel cell locomotive at the Placer Dome (CLA) Limited Campbell Mine. This technology demonstration at Campbell Mine is critical for determining technical, regulatory, and implementation aspects to be incorporated into future fuel cell prototypes such as the LHD project."

Jan 1, 2005

By M. C. Bétournay

Under the requirement to define the economic advantages of using hydrogen fuel cell vehicles, a broad-scoped project was initiated to quantify the costs associated with operating fuel cell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another. This paper outlines the results of the investigations to date defining the costs/benefits associated with capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America. Significant ventilation power, equipment, and infrastructure savings are possible with the application of fuel cells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft, and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuel cell mining equipment is currently higher than diesel versions, the high cost of fuel cells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case, the operational savings would probably be sufficient to balance the supplementary capitalization costs. Comprehensive reports have been issued.

May 1, 2005

By G. Righettini, G. Desrivières, P. Mousset-Jones, R. Lacroix, M. C. Bétournay, P. Laliberté, S. Hardcastle

"Under the requirement to define the economic advantages of using hydrogen fuel cell vehicles, a broad-scoped project was initiated to quantify the costs associated with operating fuel cell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another.This paper outlines the results of the investigations to date defining the costs/benefits associated with capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America.Significant ventilation power, equipment, and infrastructure savings are possible with the application of fuel cells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft, and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuel cell mining equipment is currently higher than diesel versions the high cost of fuel cells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case, the operational savings would probably be sufficient to balance the supplementary capitalization costs.Comprehensive reports have been issued."

Jan 1, 2005

By Marc C. Bétournay

Under the requirement to define the economic advantages of using hydrogen fuelcell vehicles, a broadscoped project was initiated to quantify the costs associated with operating fuelcell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another. This article outlines the results of the investigations to date defining the costs/benefits associated with: capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America. Significant ventilation power, equipment and infrastructure savings are possible with the application of fuelcells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuelcell mining equipment is currently higher than diesel versions, the high cost of fuelcells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case the operational savings would probably be sufficient to balance the supplementary capitalization costs. A comprehensive cost-benefit report will be issued in the near future.

May 1, 2003

By John Folinsbee, Brian Danyliw, Tony Y. Chong

"Control of fugitive dust has become increasingly important in the mining industry both from a health and safety and environmental standpoint. Mining operations in particular have required improved fugitive dust control due to recent lowering of the allowable airborne silica concentration to which workers can be exposed. Experience has now proven that the implementation of a surfactant based chemical dust suppression system can enhance existing mechanical dust control methods resulting in much more efficient control of fugitive dust.The Porcupine Joint Venture (Dome Mine) utilizes dry secondary crushing and screening that makes it particularly prone to fugitive dust emissions. A variety of potential dust control systems were evaluated and this led to the installation of a surfactant based water spray system to augment the existing mechanical dust collection systems.A great deal was learned through the implementation of this system. This paper describes the entire process, from testing, system design and installation, through optimization and standardization of operation. In addition a variety of problems were identified, and innovative solutions were provided. Also, the metallurgical impacts on down stream processing are highlighted. Finally, a full discussion of overall results including a discussion of the relationship between silica and total dust concentrations is included."

Jan 1, 2005

By SME SME

NORTH AMERICAN TUNNELING 2024 PROCEEDINGS

Jun 23, 2024

By John Floyd, Maria Rocha, Benjamin Cebrian

Wall control blasting is needed in most metal mining operations in terms of increasing mineral reserves and assuring the safety of the operation. This type of blasting has the goal to achieve a clean, stable rock wall in the shortest distance from a well fragmented, easy to excavate, blasted rock mass. This can be done with a variety of blasting techniques, all of which decrease the explosive energy towards the final wall. Each technique needs to suit the geology: modified production blasting, buffer blasting, pre-split and line drilling of empty holes. Pre-split is the most expensive technique, and allows final steeper bench face angles while modified production blasting is the least expensive but needs wider berms.

Jan 1, 2018

By Xing Zhao, Michael A. Sutton, Vikrant Tiwari, Damien Bretall, Xiaomin Deng, William L. Fourney, Uli Leiste

The dynamic response of a thin aluminum plate subjected to both shallow and deeper buried blast loading was studied. Using a combination of high speed stereo-vision and three dimensional digital image correlation (3D-DIC), sequential stereo images acquired every 38.25µs during blast loading were analyzed to determine full-field deformations and plate motions (displacements, velocities and accelerations, effective surface strain and effective surface strain rate). Measurements indicate that the initial sheet deformation was highly localized for both shallow and deeper blast events, with extremely high velocity and acceleration values recorded during the earliest stages of impact loading. Full field strain and strain rate data indicate that well defined strain and strain rate “maxima” are created in the plate, with the potential of affecting the dynamic plate behavior as well as it local failure.

Jan 1, 2010

By M. Hesham El Naggar, Yasser Abdelghany

"ABSTRACT: The axial and lateral monotonic and cyclic behavior of helical pile foundations was investigated and new innovative helical screw systems suitable for seismic loadings were developed and patented. More than one hundred full scale field load tests were conducted on instrumented helical screw piles installed in cohesive soil. The piles included: plain helical screw piles (P-HSP); grouted (G-HSPs); fiber reinforced polymer FRP-G-HSPs; and reinforced grouted RG-HSPs. The RG-HSP piles axial capacity was more than twice that for P-HSP, with minimal reduction after cyclic loading, and their lateral capacity was more than 3 times the P-HSPs capacity. A 3-D finite element model was established. The results of 3-D finite element modeling were used to establish the load transfer mechanism and a design methodology for the considered piles.INTRODUCTION AND LITERATURE REVIEWHelical (screw) anchors have been utilized in tension loading and have gained popularity for bearing load applications. Helical piles represent an overall cost effective alternative to conventional piles for new construction and repair applications. The helical piles speed and ease of installation, less noise during installation added advantage with regards to their efficiency and reliability for underpinning including re-support and reconstruction of distressed and damaged foundations for either stabilization or rehabilitation. The “square shaft” SS175 pile is a segmented deep foundation system with helical steel bearing plates (helices) welded to a central steel shaft. Load is transferred from the shaft to the surrounding soil through these bearing plates. Segments or sections are joined with bolted couplings. Practically installed depth is limited only by soil resistance and economics. A helical bearing plate or helix is one pitch of a screw thread. All helices regardless of their diameter have a standard 75 mm pitch (Figure.1). The performance of single helical anchors and group action were studied experimentally and theoretically by several researchers, the researches focuses on the installation torque and uplift resistance. Some researches focus on the load carrying capacity with little pile response to cyclic loading effects or to instrumented full scale field testing. Helical piles axial compressive or lateral loading still is not well characterized and needs more analyses and their seismic performance was not investigated. For such this research was initiated to investigate the helical piles monotonic and cyclic performances under axial and lateral loadings to consider their usage in different applications in seismic zones. Among the several researchers, Clemence (1983); Mooney et al. (1985) conducted field and laboratory testing; Hoyt (1989), Hoyt et al. (1995), and Ghaly and Clemence (1998) conducted theoretical and experimental testing, Puri and Vijay (1984), Huang et al. (1995), Perko (2000), and Pack (2000) conducted theoretical analyses. Rao and Prasad (1993), Prasad and Rao (1994), conducted experimental testing; Vickars and Clemence (2000) studied the performance of helical piles with grouted shafts."

Jan 1, 2014

By K. Viking

The vibratory characteristics of full-scale sheet piles, vibratory driven into the ground, have so far not been described systematically in detail. This paper concerns the preliminary results of a series of full-scale field tests where both the driveability and induced ground vibrations have been continuously monitored. Furthermore, the results of measured ground vibration levels have been measured at two different sites characterised as having hard and easy driving conditions. In the light of the presented results, the paper briefly discusses how the complexity of a driveability and vibration prediction can be subdivided into three parts, namely, vibrator-, sheet pile-, and soil-related parameters, all of which significantly affect both the driveability and induced ground vibrations.

Jan 1, 2000

By B Mobilio, G B. Sharrock, J L. Lett, I Brunton, T Thornhill

Full-scale marker experiments at Cadia Valley underground operations have been ongoing for over 14 years. Initial marker experiments were undertaken in the Ridgeway sublevel cave (RW) (2002), and subsequently at Ridgeway Deeps (RWD) (2008) and Cadia East PC1 (CEPC1) (2012) block caves. Over 25 000 markers have been installed at the three caving operations to date (approximately 20 000, 3000 and 2500 for RW, RWD and CEPC1 respectively). These experiments aimed to quantify and assess the geometry of the extraction zone, development of the extraction zone over time, variability of flow behaviour and factors affecting flow behaviour in both the near and far field cave column. This paper discusses marker recovery results from the RWD and CEPC1 caves.With respect to the two cave operations, marker recovery in both the near field (markers recovered vertically within 70 m of the extraction level) and far field (markers recovered vertically above 70 m of the extraction level) indicates disturbed flow behaviour where marker recovery is not spatially uniform during material extraction. Two distinct patterns or transient behaviours in the extraction zone are indicated. For RWD (advanced undercut), early material recovery was close to the major apex, and expanded towards the centre of the drawbell as more material was extracted. The inverse was observed for CEPC1 (post undercut), where recovery occurred in the centre of the drawbell initially, and expanded outwards towards the major apex. This trend of recovery for the two operations continued in the far field. In the region above the major apex, recovery was observed for all heights, with no clear height of interaction zone (HIZ) indicated. All of these behaviours significantly deviate from both conventional ellipsoidal flow theory and Laubscher’s (2000) design guidelines. For this reason these new mechanisms are termed the Disturbed Extraction Zone (DEZ).For the CEPC1 marker experiment, electronic markers were utilised to investigate the vector movement of material in the near field. Marker recovery movement vectors in the near field indicate extraction zone widths in the order 30 m, with localised marker recovery outside this region (significant horizontal movement of material potentially due to cave muck pile rilling and blast burden movement). Analysis is ongoing for far field marker vector movement, and will be reported once additional marker recovery has been obtained.CITATION:Brunton, I, Lett, J L, Sharrock, G B, Thornhill, T and Mobilio, B, 2016. Full-scale flow marker experiments at the Ridgeway Deeps and Cadia East cave operations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 141–150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R. K. McLimans, C. Knudsen, S. Bernstein, D. Frei

Computer Controlled Scanning Electron Microscopy (CCSEM) is used to analyze indivdual mineral fractions in heavy mineral sands. CCSEM is a fully automated particle analysis technique for the determination of physical and chemical properties of a large number of individual particles. CCSEM enables the precise and accurate determination of the modal abundances of individual mineral fractions (e.g. ilmenite, rutile, zircon, or garnet), their average chemical composition (and compositional variation), as well as their physical properties such as size (e.g. diameter and perimeter length) and shape (aspect ratio and circularity). A unique sample preparation procedure is used to produce representative polished sections from cylinders of raw sand samples such that thousands of grains are present in a polished cross section, but grains are not touching. The combination of this sample preparation technique with CCSEM enables the fully automated analysis of individual grains without the application of de-agglomeration or erosion steps to separate touching particles. Hence, CCSEM yields information representative of the entire area of analyzed grains without systematic bias due to neglect of rim areas by de-agglomeration or erosion steps. Therefore, the resulting data are determined with high accuracy, precision and statistical validity. Because the sample preparation is relatively straightforward, using raw sand samples, and all chemical and physical properties are determined in one analytical session per sample, CCSEM is a powerful cost and time efficient tool for characterizing chemical and physical properties of minerals in heavy mineral sand deposits.

Jan 1, 2005

By Daniel Su

Approximately 90% of the primary roof bolts used in CONSOL?s Pittsburgh seam coal mines is 2-piece, 8-foot long, 7/8? (or ¾?), high-strength, resin assisted, mechanical shell tensioned bolt. The remaining 10% is the 2-piece, 8-foot long, 7/8? combination bolt, which employs 4 feet of fast resin to anchor the deformed rebar at the top of the hole. In either system, a 1-3/8? hole is required to accommodate the mechanical shell and the coupler. The cheaper torque-tension rebar system, which is typically fully-grouted with 2-speed resin and which typically provides low bolt tension, is not used in CONSOL?s Pittsburgh seam mines. Rather, it is used in CONSOL?s Central Appalachia mines, where the roof rocks have CMRR rating of 50 or higher. Fully-grouted headed rebars, on the other hand, are used in CONSOL?s room-and-pillar mines. The selection of tensioned versus non-tensioned, fully-grouted bolts for coal mine primary roof support has been debated for the past thirty years. Many researches have been conducted to understand the theoretical bases behind the two systems. This paper describes CONSOL?s experience of using a new fully-grouted, mechanical shell tensioned bolt in the Pittsburgh seam with the development of low insertion force resin.

Jan 1, 2007

By Juan Muñoz

La funcionalidad Start/Stop es ampliamente utilizada como una solución de ahorro de combustible y disminución de gases contaminantes en vehículos de pasajeros. En la actualidad, uno de cada dos vehículos nuevos que se fabrican en Europa, ya incorpora el sistema Start/Stop. El objetivo de este trabajo es presentar el concepto prototipo de Start/Stop Retrofit (SSR) como una innovadora transferencia tecnológica desde la industria automotriz a la industria minera, ofreciendo los mismos beneficios que en vehículos de pasajeros.

Sep 1, 2017

By Érika Aline dos Santos

Este trabalho tem como objetivo a síntese de materiais híbridos nanoestruturados à partir da funcionalização do argilomineral haloisita com (3-aminopropil)trietoxissilano (APTES) para aplicação em processos de adsorção. A rota de modificação baseou-se na acidificação e posterior reação química entre as hidroxilas superficiais da haloisita e os grupos hidrolisáveis de APTES na presença de tolueno sob refluxo. Haloisita em sua forma natural e modificada foi caracterizada por análise termogravimétrica (TG), área superficial específica (BET), espectroscopia de infravermelho (FTIR) e difração de raios X (DRX). A quantidade de APTES enxertado, calculado através da análise termogravimétrica foi de 7,32% para a amostra funcionalizada previamente acidificada e 6,50% para a amostra funcionalizada sem pré tratamento ácido. A área superficial das amostras diminuiu com a funcionalização. As amostras funcionalizadas exibiram novas bandas características de grupos de APTES no espectro obtido por FTIR confirmando a ocorrência da funcionalização do organosilano na haloisita. A análise de DRX indicou que a estrutura original não foi alterada após a funcionalização.

Aug 16, 2017

By Carl Lubbe, Ron Frye

Numerous articles have been written regarding the effects of blast control plugs in an attempt to quantify stemming ejection rates, air overpressures, fragmentation’and other parameters measured using these devices. In an effort to further attempt to understand the function of these devices, field and laboratory research conducted with various stemming devices was performed to enhance existing data sets and analyze otherphenomena that occur when these products are used.

Jan 1, 1998

A new analytical approach for characterizing and improving the performance of ball milling is presented. Individual ball mill circuit design and operating variables can be related to overall circuit performance through two distinct parameters for classification and breakage. The ball mill circuit functional performance equation is presented. Applications in the industrial plant and in the research field are discussed.

Jan 1, 1990

By K. Wood, R. McIvor, P. Blythe, M. Lavallee

A new analytical approach for characterizing and improving the performance of ball milling is presented. Individual ball mill circuit design and operating variables can be related to overall circuit performance through two distinct parameters for classification and breakage. The ball mill circuit functional performance equation is presented.Total mill x Classification x Test specific x Grinding power draw system efficiency grinding rate rate ratio= Production rate of new product size materialExamples from industrial plants and applications in the research and development field are discussed.

Jan 1, 1990