Search Documents

By J. M. Manka

American mining companies operate many drum hoists that hoist from various depths with varying payloads. This paper will review the procedure of selecting optimum wire rope constructions for these existing hoisting installations. Selection for proposed installations along with recommended hoisting parameters will also be presented. To achieve this optimum rope performance, preventative and corrective maintenance procedures will be reviewed along with examples of rope problems and their causes.

Jan 1, 1992

By Lee Browne

The transformation of Peru’s Tintaya copper project from a state-owned company to a private company is under way and the results have been successful. Since Magma Copper Co. assumed operating management in December 1994, production and costs have improved dramatically. To understand the transformation of Tintaya, the transformation of Magma Copper must also be understood.

Jan 1, 1996

By W. F. Riggs

1 Flotation Analogy To explain flotation in simpler terms the following analogy will be used. A factory (the flotation cell) manufactures a product (collector coated mineral). The product (collector coated mineral) is transported to market (the launder). A truck (the frother) is used to transport the product (collector coated mineral) to the market (the launder). The truck (the frother) transports the product over a road (the froth bed). The truck (the frother) and product (collector coated mineral) are supported by tires (the air). 2 Assumptions This operating philosophy assumes that the correct collector dosage is present along with the correct particle size distribution, pH conditions, etc. and that the minimum required frother dosage is correct. 3 Collector Addition The collector addition as used at a flotation plant is based on dosage rate as determined by the amount of mineral value entering the concentrator. Collector is normally added at two points in the concentrator: The primary flotation circuit and staged addition in the rougher scavenger circuit. Surveys have shown that the staged collector addition provides an increase in the kinetics and increases the recovery of the valued mineral in the rougher scavenger circuit. 4 Frother 4.1 Frother Dosage As explained in the above analogy, frother can be likened to the truck that transports the product (collector coated mineral) to market (the launder). Just as you would not use a truck rated at 15 tonnes to transport a 20 tonne load, you cannot expect to transport coarse minerals to the launder when there is insufficient frother present. Frother dosage must always be at, or above the minimum target. If less frother than the required minimum is used, then coarse mineral particles will not be supported and transported to launder where the mineral is recovered. To the naked eye the froth characteristics, even when insufficient frother is used, will appear to be correct. You cannot see the coarse particles that are not being recovered in the froth. (See Section 4.2 below for an explanation of why this occurs.)

Jan 1, 2006

By J. K. Borchardt

The use of statistical design to optimize deinking process design has been studied for the flotation deinking of newspapers. The interactions of two variables are often important in determining flotation deinking efficiency. The interactions can be synergistic or antagonistic. These interactions would not be discovered using the traditional method of varying one parameter and holding the other variables constant. An experiment design in which two or more process parameters are varied simultaneously is required to identify these interactions. A considerable number of conclusions could be drawn about the relative importance of process variables on ink particle size distribution, ink removal efficiency, and flotation yield loss in a flotation deinking process. However, these findings could be influenced by the deinking surfactant and the ink chemistry.

Jan 1, 2001

By S. Hamilton

Occurrences of boron-containing ores are relatively rare on a global basis. The first verifiable use of borax was in the 8th century by Arabian gold and silversmiths. Due to the rarity of the borate mineral occurrences, borates were originally traded at relatively high prices and were used for very specialized applications. Today, there are

Jan 1, 2006

Partition models are commonly used to assess the separation performance of circuits incorporating density-based processes. Unfortunately, this useful tool has traditionally been overlooked by the heavy minerals sands industry due to difficulties associated with the use of toxic dense liquids. In the present study, this problem has been avoided via the development of partition models based on experimental data from microscopic grain-counts. This technique, which uses different mineral species as density tracers, provides a new tool for evaluating the multi-stage circuits that are required to successfully upgrade heavy mineral sands. The partition model approach easily identifies shortcomings of existing circuits and, when used with conjunction with linear circuit analysis, provides tremendous insight regarding the optimum arrangement of unit operations in terms of separation efficiency and plant throughput capacity. An industrial case involving the redesign of a heavy mineral sand spiral plant is presented to demonstrate the utility of these process engineering tools in plant optimization.

Jan 1, 2009

By X. Zhu, R. Du Plessis, J. D. Miller, D. G. Kotylar

Research on the low-potential hydrophobic state of pyrite with potassium amyl xanthate (PAX) as collector, is reported to help explain and understand the fundamental aspects of the N2TEC flotation process, which was originally developed for the improved recovery of gold from refractory auriferous sulfide ores. Typically in the N2TEC process, air is replaced by nitrogen as the flotation gas, and potassium amyl xanthate is used as collector for the reactive auriferous pyrite particles. The first N2TEC flotation process was commissioned at Lone Tree in Nevada in March 1997 and has been in operation ever since. On the basis of electrochemically controlled contact angle measurements, the low-potential, low-pH hydrophobic state of pyrite has been examined as a function of flotation variables such as pH, gas-phase composition, collector concentration and pyrite potential.

Jan 1, 2000

By L. E. Beverage

In 2006, the Mine Improvement and New Emergency Response Act (?2006 MINER Act?), Pub. L. No. 109-236, 120 Stat. 493 (2006) was enacted in a bi-partisan move to strengthen the 1977 Mine Safety and Health Act. This action followed several underground coal mining accidents at the Sago and Aracoma Mines in West Virginia and the Darby Mine in Kentucky. The focus of that legislation was, in part, to force technological development and implementation. It involved the recomposition and training of rescue teams. Requirements for sealing worked out areas of mines were changed when MSHA invoked its Emergency Temporary Standard (?ETS?) authority for the first time in many years. Increased penalty amounts were established for certain types of violations for all types of mining, and minimums were set for unwarrantable failure violations issued under Section 104 (d)(1) and (d)(2); 30 U.S.C. Section 814 (d)(1),(2). The entire 30 C.F.R. Part 100 penalty criteria was revamped in a rulemaking, effective in April 2007. The visions were ambitious and noteworthy and those in industry and government have spent the last four years working through the aftermath of intended and unintended consequences of these changes. The penalty structure arrived at in 2007 has proven unwieldy and has contributed to the increase in contested caseload now before the Federal Mine Safety and Health Review Commission. In essence, litigation under the Mine Act ground to a virtual halt when the number of cases increased but the budget for Administrative Law Judges, who hear the cases, and the Solicitor?s office who represents MSHA, was not increased. Addressing the backlog effectively was one of the major challenges when Joe Main was confirmed as Assistant Secretary in early 2010.

Jan 1, 2011

By R. W. Smith, D. L. Taylor, K. A. Altman

Recent research has shown that traditional sensitivity, what if and best case/worst case analysis of metallurgical data has the potential to over estimate the value of mining projects. Use of simulations, which rely on the input of statistical information, may provide more realistic predictions of the value of future projects. Actual metallurgical data is used to demonstrate that analyzing the data from a statistical perspective can give insight into completing an optimum amount of metallurgical testing and a mechanism to determine that samples used for the testing are truly representative of the ore that will be processed.

Jan 1, 2000

By Manuel Gomez

This report presents prediction equations for eleven factors indicative of metallurgical coal quality which have been developed from data obtainable during exploration. Five coke strength parameters and six carbonization product yields have been predicted for coking coals having volatile matter contents in the range 16.3 to 42.1 percent, dry basis. The prediction models developed contain information from the proximate and ultimate analyses, the size consist, and the petrographic composition of coking coals carbonized in BM-AGA retorts at 800°, 900°, and 1,000°C. The equations reported have been evaluated with independent data derived from the 900°C carbonization of 33 binary blends. Present results show that metallurgical coal quality can be predicted ahead of mining. Capability to forecast coal quality is useful in mine planning and should provide basic information for optimization of blending and crushing techniques, leading to the production of uniform coke.

Jan 1, 1968

By Reginald Dias

Mining operations take a tremendous toll on equipment, operating in difficult conditions day after day. Owners and operators cannot make the job any easier, but they can give their equipment an advantage. Equipment life may be extended through preventive maintenance and the proper application of quality lubricants. This means lubricants that are made to last longer and stand up better to the punishment mining equipment must endure. There are several practices to consider as part of a successful preventive maintenance program. A good place to start is to review original equipment manufacturer recommendations about servicing and maintenance intervals for each part of the equipment, especially the engine. If these recommendations have not been followed, owners and operators must begin periodic service work on equipment to help minimize equipment down-time and extend engine life.

Jan 1, 2003

By Norbert T. Rogers

An accepted statement of fact is that, next to agriculture, transportation is the second most important industry in the world. The transportation networks of the United States have greatly contributed to our nation's growth and prosperity. The objective here is to make the reader aware of the need for communication between geologists, mining engineers, purchasing agents, and transportation managers. Only through a cooperative effort is it possible to reap the benefits of transportation in the industrial minerals field. Transportation is often thought of in terms of trucks, rail cars, barges, and covered wagons. There is much more. Corning Inc. Corning Glass Works is a worldwide organization with more than $2 billion in annual sales. It supplies more than 60,000 different products a year to some 47,000 customer firms and millions of individual consumers. Corning operates 32 of its own plants worldwide and is also an investor with a 50-50 or minority position in 24 affiliated companies in 11 countries. Corning competes in four broad business categories: • specialty glass and ceramics; • consumer housewares; • laboratory sciences; and • telecommunications Binding these four sectors together is the glue of technology. Coming's research laboratory, established in 1908, was one of the first in American industry. That early commitment to research has never wavered. Today, Corning spends annually on research and devel¬opment, as a percentage of sales, at double the average rate for all manufacturing industry in the US. Some 1500 scientists, engineers, and support personnel are now employed at the company's research and development centers in the US, Japan, and France. Petalite background A family of materials melted conventionally as a glass, then converted by special processing to a ceramic was invented in 1957. One of the basic minerals in this glass ceramic product is petalite. Petalite is a monoclinic mineral with a framework silicate structure and a low iron content, about 0.06% Fe2O3. Petalite is found in very few places throughout the world and no commercial petalite deposit has been found in the United States. Sizable deposits occur in Zimbabwe, Southwest Africa, Brazil, Australia, the Soviet Union, and Sweden. Coming's purchasing and geology departments located a source of petalite with proven reserves in what was then known as Rhodesia. The supplier was Bikita Minerals. The relationship with Bikita was one in which Bikita supplied bulk ore that Corning processed into a finished material at its US facility. This bulk ore method of shipment resulted in high losses through contamination and processing. It also caused tank upsets at the Corning plant because of iron contamination picked up through the numerous handlings of this product in bulk. The relationship with Bikita continued until 1965 when the white political leadership of Rhodesia declared its independence from Great Britain. This led to the imposition of international sanctions. The sanctions were lifted in 1980 and the relationship with Bikita was reestablished in 1983.

Jan 1, 1989

By Thomas P. Kwiatkowski, Joginder S. Bhore, Christopher D. Orlandi, Jose Velez

Three case histories of successful TBM tunneling for New York City Water Tunnel No. 3 are presented. The tunnels, costing about one billion dollars total, are the 5-milelong, 18'-11" OD Brooklyn Tunnel; the 5-mile long, 23'-2" OD Queens Tunnel, and the9-mile long, 12'-4" OD Manhattan Tunnel. The three tunnels are the first major tunnels constructed in New York City rock utilizing the TBM method of construction. This paper describes and compares the three tunnel projects in terms of geology, construction methods, TBM’s, rock and groundwater behavior, rates of advance and other performance data, and challenges and solutions encountered during the projects.

Jan 1, 2007

By S. A. Abdel Sabour

Conventional methods for selecting a production plan for an open pit mine is based on the assumption that ore grades throughout mine life as well as market variables are known with certainty. Another important issue that is also being ignored in the conventional procedure is the value of management flexibility to revise operating policy with time according to the arrival of new information. Based on this oversimplification of reality, an optimum mine plan that is thought to be maximizing net present value (NPV) of the project is selected. Given the multiple sources of risk affecting the estimated NPV, there is a high probability that the actual value will be different from that estimated. This could mislead decision making process regarding selecting an optimum mine plan. This paper proposes a multi-criteria ranking system for selection between alternative mine designs under both geological and market uncertainties. The system is based on integrating multiple market and geological uncertainties as well as the operating flexibility to revise the ultimate pit limits using a Monte Carlo-based real options valuation (ROV) model. To compare the methods, the article applies the proposed system, along with the conventional NPV-based method, to rank possible mine designs for a copper and a gold mine. It has been found that, considering multiple risk analysis measures while integrating uncertainty and operating flexibility results in selecting a mine design that is different from that selected by the conventional method.

Jan 1, 2009

By H. Lyn Bourne

This is the fifth annual tabulation of mineral royalty information. This tabulation, like the previous editions, includes all of the earlier data. There are also 60 new entries. In addition to royalty information, some entries show the cost of purchased reserves. Two articles relative to the evaluation of minerals reserves appeared in December, 1986. R.H. Paschall (In the Aggregate, ME, p 1139) wrote a good article, although it lacked specific royalty data. However, this author takes exception to two ideas in Paschall's column. Paschall contends that the royalty rate does not affect the mineral appraisal. This present author could not disagree more. Paschall also claims the location of an industrial mineral deposit is the only serious or practical caveat in comparing royalties. Comments received here from readers helped make the list of caveats that are cited each year. The readers will decide which factors influence the mineral value for their commodities of interest. Paschall's point about the relationship of the parties who are negotiating a royalty agreement is important and very well taken. The other article, written by William Vernon (Pit and Quarry, December 1986), gives a step-by-step process on how to conduct a mineral appraisal. The article cites three reasons for an appraisal: transfer rights; collateral for a loan; and taxation. A fourth reason is to establish adequate compensation for reserves lost through condemnation. This author has appeared in several court cases where compensation for loss of mineral reserves through condemnation required a mineral appraisal. Royalty rate becomes an important factor in the appraisal process, although the Pit and Quarry article refers to that part of the valuation equation as "profitability." Both articles were well written and are recommended reading for those interested in mineral valuations. The same caveats that have appeared in previous columns relative to factors that influence the value of reserves are restated. The data in the table serve as a general reference and are not intended to present an absolute scale of reserves costs. Several factors influence the value of any mineral commodity. The factors include: • location/transportation - especially significant for most industrial minerals; • market conditions both for the commodity and the company acquiring the right to mine; • quality or grade of the deposit as it reflects the amount of processing/beneficiation necessary to produce the finished product; and • legislative restrictions and conditions for mining a given material at a given site. These and other factors will significantly influence the cost of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity in column 1, and the subsequent columns give: • the location by state, US geographic area, or Canadian province ; • the cost - R for royalty and P for purchased cost; • the year in which the lease or purchase agreement occurred; and • comments or footnotes for more information. The cost column requires more explanation. The units may refer to cubic yards (/cu yd), cubic feet (/cu ft), short tons (/T), or acres (/A). 1 cu yd = 0.76 M2 1cuft = 0.28m3 1 st = 0.9072 t 1 acre - 0.4047 ha or m2

Jan 7, 1987

By K. F. Bailey

Naturally occurring asbestos in aggregate and other mineral deposits, and the release of asbestos fibers into the ambient environment, is a public health concern. Determining the presence of asbestos in an ore body also presents a considerable sampling and analytical challenge. Improper and inaccurate identification of asbestos can result in unwarranted public and worker panic leading to significant costs to mine operators both in terms of dollars and company image. Some companies have been forced out of business simply because they had the non-asbestiform, prismatic variety of one of the six asbestos minerals. In the late 70’s, asbestos was found as a contaminate in a trap rock quarry in Rockville, Maryland. This discovery led to a massive overreaction by federal, state and local governments. In 1986, the Occupational Safety and Health Administration (OSHA) promulgated a final rule that regulated the common non-asbestiform mineral habits of actinolite, tremolite, and anthophyllite as if they were asbestos. The rule was reversed after a six-year struggle. Recently, the Libby, Montana, W. R. Grace vermiculite - asbestos, as well as the California chrysotile in serpentinite, and the New Jersey Southdown quarry – asbestos events have rekindled the entire issue of naturally occurring asbestos. It is time to get this concern addressed with sound science so that real asbestos is properly identified and controlled.

Jan 1, 2002

By M. J. Ramos

Without an exclusive definition of administration in business, we could propose to define it as performance by management to adopt or implement established business formulas. Administration could also be defined as a universal process that organizes people, and achieves, through efficiency, common objectives and goals. Humanity developed some form of this process from the beginning of civilization. To imply that something is new in administration might be considered specious or naïve. Moreover, what is new in management? Administration of business is not new to the world. To prove this statement, we need only ask this question: Does the architecture and monumental workmanship of the past civilizations of ancient Egypt, Rome, and the Incas demonstrate management without administration and without definition of objectives? The answer must be a resounding ?NO!? In spite of this acknowledgment and for the purposes of this presentation, I will use the word ?new? in business and hope that the reader will follow my reasoning. The mining industry has unique characteristics in respect to other industries. It is multi-disciplinary, has a single purpose (majority for one metal), has two players (man and nature), and it involves high risks for generating environmental imbalance. Mining exploits non-renewable and finite resources, creates an unstable job market (work hard to have no work) and a speculative economic market with unpredictable prices ? a one-time payment for a finite resource with multiple recycling. On top of all that, the industry still operates within obsolete petroleum-based technology, utilizing practices that were designed two centuries ago. Today, we confront the challenges of the millennium with outmoded practices and management. Ordinarily, several styles of administration are standardized into a FRAGMENTED vertical system of organization. Mining has rigid objectives in production, with profitability as the focus from the beginning to the end. Citing the concept of safety, as an important facet of production is bombastic since, in truth, mining is an experimental industry that consistently reports high numbers of fatal accidents. In mining, we designed a process to work according to our objectives, demanding attention and supervision of all levels of management with a halo of parameters that are not assimilated into the design. We continue to perform a rigid style of management in an industry that is still not responsive to variations of the market ? losses in particular. The existing design process generates loss without capitalization and without response to said loss. This perception is reflected in a mindset that is only too ready to ignore mining liabilities. The reality of the enterprise has created an immense pressure from top to bottom in the hierarchy to do more with less. It is for all of these reasons that I propose to set forth a new essence for administration that encompasses an alternative vision and style in mining: Management by Loss. MANAGEMENT BY LOSS Management by Loss (MBL) is a systematic, integral process organized to quality control operation and the human profitability within the industry. It permits focus on achievable goals by utilizing the best practices (Mining Open-closing). Identification and characterization of loss in the process determine how objectives are defined, controlling the time limits to execute based on constant balance of mass, energy, water, and ?wastes? in each stage of the industry, in order to reach final objectives. The concept of loss can be defined by various criteria. Generally, it is the mass that could not make or arrive at its destination from a designed process or simply, it could not maintain balance. Otherwise, the design of the process describes the final point of the resource. However, those resources could not make their destination because of failure to use the best design, resources and TIME. The loss has typical characteristics such as Identifiable, classifiable, measurable, manageable, controllable, valuables, negotiable, avoidable, reportable, and monitoring. In the traditional scheme, these losses are not registered; they are made exclusions. We are trapped within a system, which was designed to obtain objectives of the industry in a specific timeframe. In the present style of administration, the focus is total - our emphasis in this treatise is in the loss. The current traditional report form contains only the most positive achievement of objectives, only the best of the exercise, humanizing numbers, without touching what we left behind or what we were waiting for to assimilate as a ?surprise account?(new account of liabilities). Management by loss is a method that redefines the concept of waste (waste zero) for controlling the mine operation under the equilibrium of the ecosystems. This method confronts the problems that impact our industry in this millennium. Understanding and quantifying losses (reserves, resources, time, energy, water, soil, materials, equipment, tasks, labor, ecosystems, etc) is a priority mandate for the industry and demands the application of a ?new ? style of administration by seeking to maintain balance instead of the disequilibrium that mining now creates in nature. It is necessary to answer questions such as: How can we minimize loss? How can the loss be assimilated during the life of the mine? What is the vision of mining in respect to the generation of waste? How can we convert liabilities into assets? In addition, the control of loss is determined in the achievement of the plan. Loss occurs because of a failure of the process in the original plan. Still we do not plan to fail but we fail to plan appropriately. It is a remarkable thing to accomplish and compel those objectives described in the original plan when that plan is designed with a determined budget. If not, we lose time and, of course, capital. Moreover, in Management by Loss (MBL), we can find answers to the following questions: What is the multiplier of productivity in mining? What are the influences of identification and characterization of loss and what is the level of efficiency of energy in order to achieve waste zero (effective cut off grade)? The challenges of mining in this millennium validate this new style of administration. Finally, it is important to point out that mining is entering into an era that has different rules, but the industry is still run by companies functioning with objectives from two centuries ago. They are trying to confront issues with concepts that are not designed for new tasks. Therefore, I ask you to consider this new style of administration of business under a vision of how the industry should be organized and managed, with an attitude of balance toward nature and social responsibility.

Jan 1, 2009

By M. Fan

Froth flotation is the most widely-used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubble on the flotation performances of different particle size fractions of coal was investigated using a bank of 10-liter flotation cells, a specially designed 50 mm inside diameter column and a 152 mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during coal froth flotation process improved flotation efficiency. The use of nanobubble in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.

Jan 1, 2012

By K. Whysner

The recycling of metal resources in mining influenced water (MIW) requires a paradigm shift from within the mine water treatment industry. The potential to recover zinc for beneficial use in the micronutrient fertilizer industry was investigated through a survey of zinc micronutrient fertilizer representatives. An application of the findings to a case study of the Argo Tunnel influent MIW was then implemented. It was concluded that the potential to beneficially reuse MIW residuals in fertilizers exists; the current process sequences of treatment will need to be modified if metal recycling is to be prioritized.

Feb 27, 2013

By Lei Fu

In the wake of the collapse of the ceiling panels in the I-90 section of the Central Artery/Tunnel (CA/T) Project in 2006, the long term performance of tunnels became the focus of the tunneling industry. At the time of the accident, the tunnel had been open to traffic for about 10 years. This paper will discuss design methods and considerations to improve the long term performance and durability of a tunnel. The major problems found during the inspection of several tunnels will also be presented and the causes for these problems will be discussed.

Jan 1, 2008