Search Documents

The Sams Creek gold deposit near Takaka in northwest Nelson was discovered in 1974 by CRA Exploration (CRAE) geologists. CRAE recognised the potential of the area and subsequently undertook a comprehensive exploration programme of geological mapping, soil and rock-chip sampling, geophysical surveys and diamond drilling. Exploration defined sporadic gold mineralisation contained entirely within a deformed and hydrothermally altered, peralkaline granite porphyry dyke with a seven kilometre strike length, and up to 60 m thickness. Rock chip samples indicated extensive and economically significant gold grades over approximately one kilometre strike of the dyke at Main Zone prospect. CRAE completed 30 diamond drill holes at this prospect and defined a limited resource. Oceana Gold Limited recommenced active exploration at the Sams Creek Project in late 2002, focusing on improving the geological understanding and known resource at Main Zone. Completion of 1041 m diamond drilling successfully increased the estimated resource to 10.7 Mt @ 2.12 g/t Au containing 729 000 oz at a 0.7 g/t cut off. A further campaign of 1560 m diamond drilling was undertaken in 2003 - 2004 to extend the resource and test the continuity of high grade mineralised zones. Deeper intersections of the porphyry dyke indicated geometrical complexity and grade variability similar to that observed at shallow levels. Recent research suggests that Sams Creek can be geologically classified as a variant of intrusion-related gold systems, and therefore comparable to some other, very large gold deposits. However, due to the rugged terrain and dyke geometry, surface drilling is reaching the limits of viability at Main Zone. If infill drilling continues to be successful then an underground decline may be developed to facilitate further exploration. Potential also exists along strike, where other significant gold anomalies are known but largely untested by drilling.

Jan 1, 2004

By Cyril Wells, Paul E. Busby, Donald P. Hart

EARLY workers in the field have established that the diffusion of nitrogen follows normal diffusion laws. Concentration-penetration data from layer analyses of reasonably pure iron specimens nitrided in an atmosphere of CO-NH, are given in the literature,' and were utilized to calculate diffusion constants for nitrogen. The diffusion of nitrogen in y-iron may be represented approximately by the equation D - 1.07x10-' e-:".'m'"'r The diflusion coefficients, D, given by this relation represent mean values, since carburization occurred simultaneously with nitriding. The rate of diffusion in a-iron has been determined from calculations based on data obtained by measuring the internal friction of samples at each of several frequencies and temperatures.' The expression for the diffusion of nitrogen in a-iron derived from these experiments is D= 1.4x10-1 e-it tudent Increasing carbon content decreases the diffusion of nitrogen in a-iron.3 Oxygen, either dissolved or combined, has been shown' to exert a marked influence on the diffusion of nitrogen from a nitriding atmosphere. D values increase rapidly with increasing amount of dissolved oxide in the metal, but diffusion is completely inhibited if preliminary oxidation has produced the slightest trace of iron oxide on the surface. Diffusion coefficients have also been calculated from permeability and solubility data,' but these values are of questionable accuracy since the boundary conditions assumed may not actually exist. Experimental Method The method selected for determining the diffusion coefficient of nitrogen in a-iron in the present investigation was the so-called fractional saturation method. This method consists of heating the specimen in an atmosphere of H2-NH8 mixtures of known composition for a predetermined time. Following this treatment, the specimen is analyzed for nitrogen; and the diffusion coefficient is calculated from a known relationship of the fractional saturation, time of diffusion, and dimensions of the specimen. This relation is based on a solution of Fick's second law and assumes that the surface of the specimen immediately reaches a given concentration which remains constant during the diffusion anneal. Tabular solutions are available4-5 and provide the relationship between fractional saturation and the quantity \/Dt /a, where D is the diffusion coefficient in cm2 per sec, t is the time of the diffusion anneal in seconds, and a, in the present experiments, is the half-thickness of the slab specimen in cm. The method is adequately discussed elsewhere.9-10 Material The material for this study consisted of 3/32 in. thick (0.24 cm) carbonyl iron plate. The major impurities in this iron are oxygen and carbon, which are readily removed by long time high temperature treatment in an atmosphere of purified hydrogen. In order to reduce the diffusion anneal time for saturation runs, some of this material was rolled to a thickness of 0.015 in. (0.038 cm) prior to the hydrogen treatment. Hydrogen treatments were carried out in a hydrogen-purified Armco iron tube heated in a global

Jan 1, 1957

By Michael Gauna

An evaluation and analysis of a coal pillar bump in a West Virginia mine indicated that the pillar bump occurred because of the unique combination of controlling factors. The pillar?s development stability factor of 2.6, based on Mark-Bieniawski strength and tributary loading, would typically indicate an adequate pillar size for long-term main entries. A combination of multiple-seam mining geometry and geological conditions resulted in stress concentration leading to the coal pillar bump. No high extraction mining had been performed in the area and the overlying works appeared to have adequate stability factors. However, it was interpreted that long-term flooding had softened the overlying pillar system and rendered all but the largest pillars ineffective. Contributing factors include large overlying pillars transmitting stress through the approximately 60 ft of interburden and the failed pillar?s location at a transition in the immediate roof from shale to hard, massive sandstone. Other contributing factors include sandstone channeling forcing the development section to mine the pillar smaller than surrounding pillars in an attempt to avoid the channel, the relatively high overburden of 1,100 ft, and the pillar?s position in the bottom of a trough within the coal horizon. Pillars subjected to similar conditions on the other side of the section did not fail where the roof was composed of shale, even though the roof exhibited evidence of high stress concentration. An analysis was undertaken to determine appropriate pillar size for future mining. The conditions were evaluated by investigating mine historical conditions, assessing pillar bearing pressures, and using Lamodel 2D coupled with traditional Mark-Bieniawski pillar strength and tributary area loading stability factors to determine the stress levels for the pillar. Recommendations for future pillar sizes were based on the critical load bearing capacity identified by the analysis. To date, no further pillar bumps have occurred.

Jan 1, 2008

By Andrew A. A, Hamilton P. J

Constraints on pore water evolution in the aquifers of a sedimentary basin may be realised through stable isotope analyses of present day waters, and their comparison with water compositions calculated to have been in isotope equilibrium with the products of diagenesis during burial. Integrated with detailed petrographic observations, and thermal, structural and stratigraphic analyses, fluid migration patterns at various stages in a basin's history can be identified. This has important implications for modelling basin hydrology, hydrocarbon distribution, and reservoir quality in the Latrobe Group, Gippsland Basin, and oil-prone successions Elsewhere.

Jan 1, 1992

By E. Kamon

This report summarizes completed research pertaining to the reaction of human subjects exposed to Self-Contained Breathing Apparatus (SCBA) stressors during escape conditions (viz., resistance breathing, C02 breathing, hot air breathing, and static positive facepiece positive pressure breathing) and the development of an automated breathing and metabolic simulator (ABMS). Volume I contains summarizes of the studies performed under this contract. Volume II is an appendix which contains more detailed descriptions of these studies.

Jan 1, 1984

By M. Rezaee

Push backs used in the production planning of open pit mines play an integral role in generating annual cash flow. Although several algorithms for push back designs have been proposed, none have studied the optimum number of push backs. In this paper, different algorithms have been implemented for the push back design of a cross section of a copper deposit and the results discussed. Moreover, the optimum number of push backs has been determined using analytical and multiple attribute decision making (MADM) methods based on minimizing the risk associated with grade uncertainty, and minimizing stripping ratio, while maximizing net present value (NPV). According to the findings, the optimum number of push backs has been proposed to be between three and six, as lower quantities of push backs are more likely to achieve the calculated net present value, and have smoother stripping ratios for different pushbacks. This approach was examined in an operating mine and the optimum number of push backs determined to be four.

Jan 1, 2012

By J. A. Finch

"Much progress has been made over the last several years in the ability to measure flotation cell hydrodynamic parameters in both the laboratory and plant. These techniques have allowed fundamental research to proceed to determine the effects that frother chemistry has on the main hydrodynamic parameters (gas hold up, bubble size) as well as on the amount of froth generation and water content of froth. A research program was begun that brought together a team consisting of private companies and a University with expertise in hydrodynamic characterization (McGill), flotation reagent applications (Flottec) and chemical synthesis (Sasol N.A.) with the purpose of characterizing frother chemistries with two goals in mind: Determine which frother chemistry can provide optimized cell hydrodynamics; and, create new frother chemistries with specific hydrodynamic properties.This paper describes the key steps that were taken that led to the development of new frother chemistry for use in flotation.The first step was the characterization of the major frother chemical families in a two phase system. The parameters measured were gas hold up, bubble size, froth height and water carrying rate at different concentrations and gas velocities.Analysis of the data indicated that definite patterns existed between frother chemistry and hydrodynamics and showed that frothers could be grouped into classes. More importantly, by modifying known frothers through chemical reaction it was shown that these frothers could be moved from one class to another. As a result of this better understanding of the interdependence of hydrodynamic and chemical properties, a new frother chemistry was proposed that was predicted to perform similarly to MIBC.The new frother was synthesized and hydrodynamic testing confirmed that the chemical performed similar to MIBC. Laboratory flotation tests were conducted on two different ore types that also confirmed the similar performance of the new chemical and MIBC. Subsequently, the new product was placed on a plant for a short period of time. The results showed that the product was an excellent frother but increased the flotation rate slightly more than MIBC at the same addition rate.Further research showed that the new frother chemistry was a family of products. By changing the reaction the resultant products could be made to be slightly weaker or stronger than MIBC but that this chemistry cannot provide hydrodynamic/froth characteristics similar to strong frothers like glycols and glycol ethers. Further work is planned to conduct longer plant trials to confirm the efficacy of this new frother family."

Jan 1, 2007

By B. W. Madsen

To help maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines developed a mathematical model that describes acidic ferric sulfate leaching of copper from sulfide ores. The leaching model can aid in maximizing minerals and metals recovery from primary sources by giving operators and management a better understanding of the copper leaching process. This will aid in improving dump leaching operations. The model is based on a steady-state approximation of the continuity equation for diffusion of ferric ions in the rock pores and the intrinsic leaching kinetics of the various sulfide mineral particles. Ore characteristics included in the model were ore particle-size distribution, particle shape, grade, mineral content, mineral particle size, porosity, and tortuosity. The continuity equation was used with ferric ion concentration gradients and a fixed value for the diffusion coefficient. Except for effective diffusivity, each of these factors was either measured experimentally or estimated from theoretical considerations. The effective diffusivities were determined by fitting calculated leaching curves with experimental leaching data. Vertical variations in leach solution composition and temperature within a dump are not considered in this model. The model accurately predicted copper extractions for several large-scale tests during nearly 500 days of leaching.

Jan 1, 1981

By J. R. Parga

In mineral processing, poor froth-flotation performance translates into both an enormous loss of revenue and an unnecessary waste of the ore reserve. In this context, Bacís Mining Company developed a versatile new, high-performance flotation-cell design that can be incorporated into various flotation circuits. The main feature of this circular cell is that it is comprised of two separate sections, namely, a flotation cell that uses wash water to minimize the entrainment of fine gangue particles into the froth product and an external bubble generator that produces small bubbles of relatively uniform size at a specified aeration-rate. The air/water mixture is blended with the pulp by gentle agitation, so as to enhance particle-bubble aggregate-stability. Comparative metallurgical performance with conventional flotation cells show that the power requirements and operating costs for precious metal flotation are three times lower, while the concentrate grade is 7% higher and the recoveries of precious metals are 5% higher.

Jan 1, 2009

By Thomas H. Wilson

Common offset and refraction seismic data have been collected over four longwall panels at two different locations within West Virginia. Surveys prior, during and after mining were made in both areas. The velocity of seismic wave propagation in the overburden rocks is observed to decrease in response to panel emplacement. Variations in the magnitude of this reduction, apparent as an additional first arrival time delay in the after mining common offset surveys, do not appear to correlate directly to the amount of subsidence that has occurred. Velocity reduction and signal absorption zones are also produced in the cover beyond the panel face over the adjacent unmined areas. Signal absorption and velocity reduction zones have also been observed over room and pillar entry areas between mined panels. Velocity reduction zones have been- observed beyond the panel face in both shallow and deep mines, but the signal absorption zone has not been observed over the deeper mine. Changes in the compressional wave velocities of the cover rocks are associated with changes in their elastic moduli. Differences between borehole derived and surface seismic derived interval velocities, are related to differences in the properties of the bulk volume sampled by each method.

Jan 1, 1988

By W. S. Landers

This report presents a detailed study of low temperature, entrained-bed carbonization of an Australian coking coal. The coal studied was high-volatile B bituminous from the Foybrook mine, an open-cut operation in the Liddell seam, New South Wales, Australia. Carbonization was conducted in an 8-inch diameter, continuous vertical reactor at several temperatures from 960° to 1,300° F. It was demonstrated that this bituminous coal can be carbonized within this temperature range to produce tar and a nonagglomerated char, without prior oxidation or char recirculation. Carbonization rates from 138 to 287 lb/hr (as-carbonized basis) were investigated. It was found that the carbonization temperature and the air-to-coal ratio must exceed minimum values to insure continuous operation. At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coa1 ratios, part of the heat for carbonization was supplied externally. On the moisture-and ash-free basis, the yield of tar plus light oil ranged from about 26 to 44 gallons per ton, and the char yield ranged from approximately 1,160 to 1,370 pounds per ton. The heat in the gas ranged from about 900 to 3,000 Btu/lb of moisture-and ash-free coal. Carbonization product yields correlated well with air-to-coal ratio and carbonization temperatures. The volatile matter in the char was found to be temperature dependent. At 1,300° F carbonization, the volatile matter in the char was 8.7 percent (dry basis), whereas at 9600 F carbonization, the residual volatile matter was about 16 to 18 percent (dry basis).

Jan 1, 1965

By P. Perruzza, R. Grandori, A. De Biase, A. Ciamei, A. Busillo

The Turin metro alluvium soil is mainly made of large boulders, cobbles and gravel , few sand and almost no fines. This grain size curve is out of the range of application for EPB and Slurry TBMs. In order to bore 5 of the total 7,5 kms of Line 1 tunnel, two specially designed Lovat EPB TBMs were utilised in combination with a systematic non structural pre-grouting of a small volume rectangular slab just above the tunnel section. The same pre-grouting was not however applicable for lack of access on surface in some sections of the remaining 2,5 km of tunnel that had to be bored below important buildings/structures, with under ground water pressure up to 1,5 bar, with curves radius of 180 m only. For these more critical sections it was necessary to study and implement a new technical solution and improve the capacity of the TBM to work efficiently in EPB mode even in this unsuitable ground and overall conditions. After months of studies the selected and adopted solution has been to inject inside the cutterhead chamber, in addition to the almost standard foams & polymers additive mixes, a suspension of limestone powders. This with the scope of compensating the lack of fines of the natural ground with rock powders.

Jan 1, 2005

By Laurence McGonagle

"The Highland Uranium Project (HUP) is located approximately sixty miles northeast of Casper, Wyoming and is owned and operated by Power Resources, Inc. (PRI). With an annual production of680 tonnes (1.5 million lbs) U308, HUP is one of the largest uranium producers by in-situ leach (ISL) in the western world. Uranium is currently produced from four wellfields with a total flow rate of approximately 1,135 m3/hr (5,000 gpm). The carbonate leach solutions are processed by anion ion exchange at two satellite facilities located in close proximity to the wellfields. The loaded resin is transported by truck to a central processing facility for elution of the uranium. Uranium in the pregnant eluant is precipitated and washed prior to calcining.Wastewater from the satellite facilities is treated and used for irrigation at a Land Application Facility. The wastewater generated at the central processing facility is injected into a 2,750 m (9,000 ft) deep waste disposal well.When economical mining of the orebodies is complete, restoration of the groundwater is initiated. There are currently two wellfields at HUP undergoing ground water restoration. Phase I restoration consists of removal of the carbonate leach solution from the ore body. Phase II includes treating the withdrawn fluid with reverse osmosis and reinjection of the permeate into perimeter wells.Future plans include construction of additional satellite facilities at the Gas Hills Project and other economical deposits located within 240 km (150 mi) of HUP. The capacity of the central processing facility will be increased to 1,815 tonnes (4 million lbs) U308 per year by late 1999."

Jan 1, 1998

Seam correlation in the central Rapahoe Sector (Greymouth Coalfield) can be enhanced by detailed lithostratigraphy and chronostratigraphy. Rewanui Coal Measures are overlain comformably by lacustrine, deltaic and fluvial strata, and this upper contact can be located using lithological and geophysical log character. The Cretaceous-Tertiary Boundary (KTB) occurs near the top of Rewanui Coal Measures and has been identified palynologically in 16 drillholes. The Rapahoe Sector can be subdivided into two palynostratigraphic domains which adjoin along a basement normal fault which was downthrown to the north during coal measure deposition. The KTB provides an isochronous surface which is independent of the lithostratigraphic datum. Using the KTB as a datum, the æUpperÆ, æMainÆ and æSubmainÆ seams can be reliably correlated throughout the southern and central Rapahoe Sector. Similarly, the æSubmainÆ seam can be correlated with æcÆ seam of the Strongman Mine area, though other Strongman seams are absent from the central and southern Rapahoe Sector.

Jan 1, 1996

By Bryan Buchholz, N. Kumar Kittusamy

Previous studies indicate that operators of heavy construction equipment are afflicted by musculoskeletal injuries of the arms, shoulders, neck, and lower back. These injuries appear to be due to excessive periods of sitting (static posture), work intensity, whole-body vibration, high resistance levers, repetitive motions, and awkward postures. (2-5) Although numerous studies have shown an association between operation of heavy construction equipment and symptoms of musculoskeletal disorders, very little research has been performed that systematically characterizes operating engineers' exposure to ergonomic hazards. The objective of this study was to systematically characterize the ergonomic hazards associated with excavating operations. As such, the following were performed: (1) vibrations were measured at the operator/seat interface (X, Y, and Z axes), and at the floor of the cab (Z axis); (2) psychophysical ratings of whole-body vibration (WBV) level and overall seat design were obtained; and (3) postural assessments of the job were made. Methodology This study evaluated an inexperienced female operator performing excavation, utilizing two different pieces of equipment. The operator was 37 years old, 162 cm tall, and weighed 80 kg. She had approximately 15 hours of operation time (experience) on the equipment evaluated. The two pieces of equipment used were: a Case Super 580E (1986) backhoe/loader, and an Insley H-2000 excavator (1975) (see Figures 1 and 2). More evaluations were performed on the backhoe/loader than on the excavator. The following evaluations were performed on the Case equipment: 1) vibration levels at the seat and floor; 2) psychophysical ratings of the overall seat design and vibration levels (for the task duration, and for an 8 hour duration); and 3) postural assessments. For the Insley equipment, all of the evaluations were performed except vibration measurements. When the evaluations were conducted, the following environmental conditions were noted: the temperature was 31°F, and soil and terrain conditions were rough and frozen.

By J. A. Bakken, M. T. Jonsson, G. A. Saevarsdottir, H. Palsson

The electrodes of a Submerged Arc Furnaces carry a high current and are subject to enormous stresses caused by both the electric arc itself, and the current distribution within the electrode. The external effect of the arc on the electrode is treated in a different paper at this conference, The purpose of this paper is to analyze the thermal effects of ohmic heating within the electrode at the arc attachment on the carbon based electrode, using data for Søderberg electrodes. The thermal conditions are then used to examine stress conditions in the vicinity of an arc. Two types of models of an electrode are presented in the paper. The first type is an accurate finite element model, based on both two and three dimensional elements and the second type is an one dimensional model, providing better insight into the problem. For the second type, a spherical model of thermal conditions in a semi-infinite solid has been developed. Results show that the electrode surface is heated quickly up to a maximum temperature and for a specific test case, the surface can only withstand the load for about 10 seconds. Also, the thermal stresses on the surface are very high which will increase erosion on the surface in addition to normal evaporation.

Jan 1, 2007

By James R. Kerr

This study reviews the sulfur and suliuric acid industries in Eastern United States with emphasis on patterns of consumption and marketing. Output of sulfur in the East is relatively small, and most of the area's sulfur requirements are met by gulf coast Frasch sulfur. Over the long ten recovered elemental sulfur from sour natural gas and petroleum may become the East's major source of sulfur. In 1958 sulfuric acid manufacture consumed over 80 percent of the area's sulfur requirements. The leading uses for sulfuric acid were the manufacture of superphosphates and chemicals. Over the years, unit requirements for sulfur and acid in many major markets have been reduced through improved technology, but new markets always have been developed to keep the industry vital and growing.

Jan 1, 1965

By Luis Alberto Medina

La característica principal de la composición de un cuerpo mineralizado es la heterogeneidad, dado que sus elementos no son iguales. En ese sentido, la prueba de heterogeneidad en el mineral de Cerro Verde, es una guía para la geología, mina, metalurgia y laboratorio químico, que busca optimizar los protocolos de muestreo y minimizar errores en las muestras tales como: Error Fundamental; Error de Segregación, generado por una muestra o submuestra cuando es cuarteada; Error de Extracción, generado por una muestra pequeña o insignificante colectada o tomada, y Error de Preparación, producido por la pérdida excesiva de finos. De acuerdo al estudio, el presente trabajo señala que la heterogeneidad de cobre total, cobre soluble en ácido y cobre soluble en cianuro, desarrollada para el mineral de Cerro Verde, es baja, lo que permite un manejo operacional sencillo para el muestreo con protocolos más simples, mientras que el parámetro más heterogéneo es el cobre soluble en cianuro y el protocolo podría ser afectado en el error fundamental.

Sep 13, 2001

By A. M. Hearn, J. G. Roos

Energy consumption, being a large proportion of the input of the ferroalloy production process, can be measured in terms of the efficiency with which the energy is utilized and the effectiveness with which it is used. The efficiency of the usage of energy revolves around the specific consumption of the energy for the production of the alloy, which encompasses the thermodynamic aspects of the process and is more of a metallurgical function that will not be addressed further in this paper. The effectiveness with which the energy is utilized is determined by the optimisation of the electricity supply from the utility (in this case Eskom). The South African electricity supply industry is on the brink of considerable restructuring, implying changes in ownership, structure and regulation. In other countries, however, restructuring has often seen higher prices. Owing to the diversity of growth prospects in South African markets, Eskom is turning to new market management and generation strategies. In future, Eskom will develop pricing strategies to increase demand from attractive customer segments such as paper & pulp, iron & steel, aluminium, and other metallurgical industries. There will be a broader spectrum of product offerings, including dynamic pricing options and demand-side management incentives. In a future electricity market that will become more dynamic and demanding, it will become increasingly important for electricity consumers to optimise their electricity supply. There are many facets in optimising the electricity supply, which include optimal utilisation of the tariff, integrating energy cost management into the production planning process, implementation of demand-side management actions, modelling, scenario planning (.what-ifs?.), optimisation, maintenance scheduling coordinated with the tariff periods, etc. This paper gives consideration to the status of the development of technology at the manganese alloy works of Samancor at Meyerton, South Africa in order to increase the effectiveness with which energy is utilized.

Jan 1, 2004

By R. Dippenaar

The emergence of new steel grades is largely driven by the need to produce high quality steel at a competitive price. The principal aims are to attain ultra-high purity, (especially low interstitial elements) and ultra-cleanliness (by the control of the inclusion content and size). Whereas the steel used to build the Titanic contained 650 ppm sulphur, resulting in MnS stringer-inclusions 25 mm in length, modern quality requirements for arctic pipelines would only allow 10 ppm of sulphur and inclusions in ball-bearing steels must be smaller than 5µm. Most developments are aimed at hot-metal treatment before refining and ladle treatment after decarburisation. Because ferroalloys are added during or after the refining step, it is the secondary (ladle) refining production technologies that are of specific interest to the ferroalloy producer. Through ladle treatment, hydrogen and nitrogen contents are reduced, ultra-low levels of solute impurities are attained and the shapes as well as the composition of inclusions are modified. Steelmakers are concerned about the cost effectiveness of the use of ferroalloys such as consistent product analysis and delivery, improved financing arrangements and technical support. Minimal variation in product sizing is vital because it impacts on handling problems and because particle size determines the rate of particle dissolution. The required ferroalloy product quality depends on the specific use but in general sulphur, phosphorous and nitrogen contents are of concern. Apart from the presence of trace and impurity elements, ferroalloys also contain inclusions. For example, ferromanganese may contain MnO-MnS-SiO2 inclusions while high-carbon ferro-chrome may contain different kinds of Cr-Mn-spinels. The presence of these impurities and inclusions has a significant impact on steel production techniques and cost and hence, on the selection and use of ferroalloys. The interrelationship between ferroalloy quality and steel production technology is plant and product specific and hence, effective communication between ferroalloy suppliers and steel producers is essential.

Jan 1, 2004