Search Documents

By K. Unkug

It is commonly accepted that the tension of roof bolts can be used as a measure of the effectiveness of roof support performance in coal bearing strata. The conceptual base for the assumption originates from beam theory. Roof bolt tension acting across the bedding and other weakness planes increases friction, preventing potential separation and slippage within the roof strata and therefore, increases the stiffness of the roof beam between the open face and the rock-mass enclosed within the anchorage. Thus, it is important to monitor roof bolt tension, especially for research purposes, and consequently many measuring systems were developed based on numerous working principles. Research planned by the Department of Mining Engineering at the University of Kentucky required a large number of tension measuring devices of high precision. These were intended to operate reliably in corrosive mine environment over long periods of time. After evaluating the existing systems, it was decided to develop a new type of roof bolt dynamometer which would fulfill the above requirements at minimal Cost. Nearly one hundred such dynamometers were constructed, calibrated and installed in two underground mines. They remained in service for a period of one Year, producing a valuable database for the Project. In this paper the working principle of this new type of dynamometer will be described and technical considerations and samples of the collected data will be given.

Jan 1, 1986

By L. Malmgren, A. Ansell

This paper deals with the influence from blast induced stress waves on the performance of shotcrete support in the Kiirunavaara mine. Time histories of stress waves from blasting were obtained from measurements during production blasts in the mine, followed by failure mapping. A finite element model, consisting of beam and spring elements, was used to calculate the shotcrete response to vibrations from blasting. The modelling approach was similar to that of a building during an earthquake, with accelerations measured in-situ used as loads. The analysis showed that the calculated adhesive stresses exceeded the strength in the interface between rock and shotcrete near to the blasted ring. It also indicated that tensile rock failure did occur. These types of failure will presumably result in ejection of joint defined rock blocks or rock slabs and will require a ductile support, such as fibre reinforced shotcrete. The predicted failure was confirmed by the mapping, which also showed that the zone of failed shotcrete was much larger in areas with plain shotcrete compared to areas with reinforced shotcrete. L’influence de l’onde de pression générée par les sautages à la mine de fer de Kiruna sur la performance du béton projeté est étudiée dans le présent article. Les ondes créées par les sautages ont été enregistrées et les domages résultants ont été cartographiés. La réponse du béton projeté aux vibrations de sautage est étudiée à l’aide d’un modèle d’éléments finis, constitué de poutres et de ressorts. L’approche est similaire à celle d’un immeuble subissant un tremblement de terre, avec les accélérations internes utilisées comme charges. L’analyse montre qu’à proximité des sautages, la contrainte adhésive dépasse la résistance de l’interface roche-béton. L’analyse confirme aussi l’existence de ruptures en tension. Ces types de rupture induisent probablement l’éjection des blocks définis par les structures du massif rocheux et requierent un support ductil, comme du béton projeté renforcé par exemple. Le type de rupture est confirmé par les observations de terrain, qui montrent aussi une extension plus importante des domages lorsque le béton projeté n’est pas renforcé. In diesem Konferenzbeitrag geht es um den Einfluss, der aus einer Sprengung hervorgerufenen Schwingungswellen auf die Ausführung der Spritzbetonverstärkung in dem Kiirunavaara Bergwerk. Die Aufzeichnungen der Schwingungswellen von Sprengungen gemäß einer Fehlerkartierung beziehen sich auf Messungen, die während der Sprengungen durchgeführt wurden. Ein Finite Elemente Modell, bestehend aus Stab- und Federelementen, wurde für die Berechnung der Spritzbetondeformation in Bezug auf die Schwingungen aus Sprengungen angewendet. Die Modellierungsmethode war ähnlich der eines Gebäudes während eines Erdbebens anhand der gemessenen Beschleunigungen vor Ort, die als Lasten benutzt wurden. Die Untersuchung hat gezeigt, dass die berechnete Haftspannung größer war als die Festigkeit in der Verbindung zwischen Gestein und Spritzbeton in der Nähe des Sprengungscentrums. Die Analyse hat gezeigt, dass die Zugfestigkeit des Gesteins versagte. Diese Arten von Versagen werden als Folge der Herausnahme von Gesteinsbrocken oder Gesteinsplatten erklärt und benötigen eine faserverstärkte Spritzbeton. Das vorausgesagte Versagen bestätigte sich beim Kartieren, welches auch zeigte, dass die Zone des versagenden Spritzbetons in Bereichen mit unverstärktem Spritzbeton viel größer war als in Bereichen mit armierten Spritzbeton.

Jan 1, 2003

The Tasman Orogenic Zone is regarded as a single metallogenic province (the Tasman Province) with four SUb-provinces corresponding with its major tectonic components: the Lachlan, New England, Hodgkinson.and North Queensland orogenic provinces. Within the Tasman Province there are four main ore-rock associations.These are1. manganese and iron with sedimentary and basic volcanic rocks,2. zinc-lead-copper and copper with intermediate-acid volcanic sequences,3. minor chromium, platinum, and osmiridium with ultramafic complexes, and4. tin, wolfram, gold, and copper with syn- and posttectonic granitic intrusions.Whereas the ores of ultramafic and volcanic associations form geographically-restricted metallogenic districts, the ubiquitous granitic ores may be subdivided into twenty-one districts that cover almost the entireOrogenic Zone. The Tasman Province is notably lacking in uranium ores and Mississippi Valley-type deposits.There is a distinct tendency for ores of each association to be progressively younger to the east and north, thus paralleling the progressive growth and stabilization of the Zone. Similar ore-rock associations are present in repeated phases of mineralization from the Cambrian to the Permian-Triassic, reflecting the essential homogeneity of the Tasman Province, and the similarity of the successive tectonic cycles.

Jan 1, 1972

Mining steeply dipping coal seams is a difficult task in the mining industry. Prior to 1996, fully mechanized longwall mining methods along the seam strike direction were tried in China and other countries. Due to its larger coal reserve in steep seams, China made more but still limited progresses on mining in such seams than the other major coal-mining countries. In the last two decades, accelerated research efforts have been made to improve the mining technology in steeply dipping coal seams. Based on these works, a dynamic model of ?R-S-F? system under asymmetrical constrains in mining steep seam is established and the theory of strata control and hazard prevention begin to be formed. The key technologies for mining steep coal seams include: global and regional strata control methods in longwall face, methods for the longwall face machines to sustain static and dynamic loads, and flexible protection technology. These theory and technologies have been successfully applied to mining of steep coal seams of varying thickness and hardness, with hard and soft roof and floor, and with high potential of spontaneous combustion in China. In the recent years, the technology has been introduced to Russia, India, Uzbekistan and other countries where steep coal seams are mined.

Jan 1, 2012

By T. Güyagüler, A. Güngör

Labour protection, that is prevention of occupational disease and reduction in the frequency of accident, has always been a matter of major concern of mining industry. Management and the government should promote and maintain high safety standards through some measures to reduce accident frequency and occupational disease. This can be achieved by using the science and technology for improving the working conditions, educating workers and managers about accidents and prevention techniques. The detailed analysis of an accident requires knowledge of many factors such as location, time, type, cost of accident, victim, nature of the injury, personal and environmental factors etc. that can be obtained from the standard coded accident report form. There is a need to prepare safety data in a common format to produce a common safety reporting system and ‘Occupational Health and Safety Management Tool’ is being designed to manage this by using database and Internet technology. Precautions should be taken according to results from database queries by providing comprehensive and accurate national data. To have an accident is unfortunate, however, to have an accident and learn nothing from it is unforgivable. Keywords: Occupational health and safety, Accident report form, Accident database, Occupational diseases and accidents, Safety reporting system.

Jan 1, 2003

By S. R. Zimmerley

[In the course of a flotation investi£ation, a siliceous gold ore was ground in a'ball mill to ':1inns 300-meeh. It wa. found that the small amotIDt of _Ius 300-mesh material had a gole.. assay approximately twice that of the oriGinal ore, &~d that this overs.ize nroduct also contained much abrac..ed iron. .,Joreove I the gold assay of the abraded iron t which was !1epnrated ma§metically', ~iVFl.£ eight ti;nes that of the are. These facts suggested that some r31aticnship ex?...,ted between the abnorma11y high gold content an the prese:1ce of brA-cit)" iron. It was decided, therefore, to investigate furt~er th~ Fl.Gsociation of the bold ~ith the iron abraded from the balls during sri~Qing ]

Jan 1, 1937

By C. Pelley, S. Kelebek, T. Katsabanis, B. Nanthakumar

"As part of a larger investigation on generation of fines from mining activities and their effect on downstream operations, ore samples from Onaping area stockpiles of Falconbridge Ltd were studied. Batch flotation tests were conducted on the stockpile samples and fresh ore samples to explore the effect of stockpiling on grade-recovery performance. Head grade and particle size distribution of the samples from stockpiles were adjusted so that the samples compared are similar to each other. In additional tests, fresh ore samples were blended with stockpile samples at various percentages, representing 27.4, 50.2 and 81.5% of stockpile samples.The samples from stockpiles produced inferior nickel grade-recovery curves compared to fresh ore. The poorer grade-recovery performance was attributable to two factors. First, a significant dilution effect was observed due to the nearly complete flotation of pyrrhotite. Secondly, while pyrrhotite from stockpiled ore became highly floatable, the same stockpiling conditions caused nickel losses that were attributable to non-floatability of some pentlandite.In the case of blending, there was generally insignificant difference in the nickel grade-recovery between fresh and blended samples when the blending cases involved 27.4 and 50.2% stockpile samples. However, an increase in pyrrhotite recovery was observed for both blending cases. At 81.5% blending case, degraded grade-recovery was significant primarily due to the nearly complete flotation of pyrrhotite. There was a small, but noticeable amount of nickel loss for this case. However, for lower ratios of blending this loss was negligible.The increase in pyrrhotite recovery was partly attributed to its activation by Cu and Ni ions. Formation of a significant amount of elemental sulphur was also apparent from analysis of stockpiled samples. It can be concluded that pyrrhotite is mildly oxidized under stockpiling conditions while part of the pentlandite undergoes a more severe oxidation."

Jan 1, 2006

By Lawrence M. Zanko

Eighteen coarse taconite tailings samples were collected in 2000-2001 from five western Mesabi Range taconite (iron ore) operations located in northern Minnesota, i.e., EVTAC, Hibbing Taconite (Hibtac), USX Minntac, Ispat Inland (Minorca), and National Steel Pellet Company (NSPC), to test their physical, geological, chemical, and mineralogical properties [Zanko, L.M., Niles, H.B., Oreskovich, J.A., 2003. Properties and aggregate potential of coarse taconite tailings from five Minnesota taconite operations, Minnesota Department of Transportation, Local Road Research Board, St. Paul, MN, Report No. 2004-06 (also as Natural Resources Research Institute technical report, NRRI/TR-2003/44)]. The goal was to assemble a body of technical data that could be used to better assess the potential of using a crushed taconite mining byproduct like coarse tailings for more widespread construction aggregate purposes, primarily in roads and high¬ways. An important part of the mineralogical assessment included X-ray diffraction (XRD) analyses and microscopic (polarized light microscopy, scanning electron microscopy, and transmission electron microscopy, i.e., PLM, SEM, and TEM, respectively) evaluation of the size and shape (morphological) characteristics of potentially respirable microscopic mineral particles and fragments. Quantitative mineralogy, based on XRD analyses, showed that the dominant mineral in all samples was quartz (55-60%), followed by much smaller amounts of iron oxides, carbonates, and silicates. Specialized microscopic analyses and testing performed by the RJ Lee Group, Monroeville, PA, on both pulverized (-200 mesh, or 0.075 mm) and as-is sample composites showed that no regulated asbestos minerals or amphibole minerals were detected in the western Mesabi Range samples. A small number (26) of non-asbestos and non¬amphibole mineral cleavage fragments/mineral fibers were detected by SEM out of 1000 fields analyzed, but most were identified as min¬nesotaite and talc, silicate minerals common to the Biwabik Iron Formation. Amphibole minerals, absent in coarse tailings samples from the five western Mesabi Range taconite operations, were present in a single eastern Biwabik Iron Formation sample collected in 2003 for Lake County from the Cliffs Northshore operation in Silver Bay, MN. Importantly, the Superfund Method for the Determination of Releasable Asbestos in Soils and Bulk Materials [United States Environ¬mental Protection Agency (USEPA), 1997. Superfund method for the determination of releasable asbestos in soils and bulk materials, EPA 540-R-97-028, U.S. Environmental Protection Agency, Washington], as modified by Berman and Kolk [Berman, D.W., Kolk, A.J., 2000. Modified elutriator method for the determination of asbestos in soils and bulk materials, Revision 1: Submitted to the U.S. Envi¬ronmental Protection Agency, Region 8, May 23, 2000] failed to generate any protocol fibers, i.e., fibers longer than 5 µm and thinner than 0.5 µm, from either the western coarse tailings samples or the single eastern Biwabik Iron Formation sample. The combined findings suggest coarse tailings and other taconite mining byproducts should be treated with the same common sense safety and industrial hygiene approach practiced for all mineral-based materials that have the potential to generate respirable dust. © 2007 Elsevier Inc. All rights reserved.

Jan 1, 2007

By D. Turnbull, H. N. Treaftis

Precipitation of tin from Pb-Sn alloys (lead-rich) occurs by the nucleation and growth of hemispherical cells which consist of tin lomelloe interspersed in the depleted solid solution. Nucleation and growth of these cells and the tin interlamellar spacing at various compositions and temperatures have been investigated. The interlamellar spacing increases approximately as the reciprocal of the logarithm of the supersaturation ratio. For constant initial tin concentration the concentration of cell nuclei increases with decreasing temperature to a limiting temperature-independent value. The kinetic results support the view that the cell growth rote is governed by the diffusion of tin along the cell boundary. In the main, the results confirm the authors' earlier deductions, drawn from resistometric and calorimetric data, about the precipitation mechonism. IT has been shown1, 2 that tin (ß) precipitates from lead-rich (a) PbSn solutions by the nucleation and growth of cells (cellular or discontinuous precipitation). These cells consist of tin lamellae, with a spacing 1, interspersed in a depleted a solution. Reorientation of a also accompanies cell growth. The kinetics of cellular precipitation of tin from lead have been measured by resistometric2, 3 and ca1orimetric1, 3 techniques. The time-transformation isotherms (t equals time; x, volume fraction of specimen transformed) of the initial rapid precipitation, which drains about 60 pet of the tin from solution, have been described by a kinetic law having the form x = 1 —exp (—bt n) [I] where n usually has the value 3.0. It was shown" that this law and the other kinetic facts can be explained satisfactorily if it is assumed that the cells grow at a constant rate and that all the cells nucleate in a time negligible in comparison with the period of cell growth before impingement. Thus, for hemispherical cells b = (2/3)pNG3 [21 where G is the rate of cell growth in cm per sec, and N is the number of cell nuclei per unit volume. The rapid rate of cell growth at low temperatures can be accounted for"' if it is assumed that the dissolved tin drains to the lamellae edges by diffusion along the sweeping cell boundary rather than by diffusion through the a crystal (volume diffusion). For cell growth governed by cell boundary diffusion it was shown, approximately G=2(X° - X° / X° ) DBA / l2 where A equals the thickness of the cell boundary; D R, the coefficient of diffusion of tin atoms within the boundary; and X° and X, are the atom fractions of tin in the supersaturated and saturated solutions, respectively. Zener8 had already shown that, where

Jan 1, 1959

By T. J. Goff

Keywords: accurate control, matte level, smelting operations, process control, tapping, sounding bar, electromagnetic measurement [ ] Accurate control of matte levels during primary matte smelting operations is desirable in order to improve process decision-making. High matte levels in the vessel could have to disastrous consequences, particularly in the new generation of intensive smelting furnace with deep-cooled copper coolers. Knowing when to commence tapping and a better understanding of melt times can only be improved if the furnace levels are monitored correctly. At Lonmin Marikana Smelter Division it has long been understood that the matte level information being provided by the manual sounding bar is only as good as the operators? following of measurement procedure, their skill in assessing what the sounding bar is displaying, and their individual interpretation of what they are looking at. This paper sets out to show how this problem was identified as an area of major concern to the plant, how a solution was sought and how an electromagnetic measurement system was installed as an alternative measurement to the matte sounding bar system. Other areas discussed in the paper are the difficulties to be overcome when first installing new equipment and how these teething problems were solved by close co-operation between Lonmin and equipment suppliers, which led to some design modifications to the delivery system. In conclusion the paper discusses the results between the electromagnetic measurement and the manual sounding measurement and how best to integrate the generated data into the plant?s process control system for improved decision making.

Jan 1, 2011

[ ]

Jan 1, 2009

By G. Hames, A. Drake, B. Sampson

The Timbarra opencut gold mine is located about 30 km(19 miles) southeast of Tenterfield in northern NSW some 4 hours by car from Brisbane, the capital city of Queensland in Australia. It was a small operation designed to produce about 40000 ounces of gold per annum utilising contract mining and company owned crushing plant feeding heap leach pads. This is a standard setup except that the mine owner was in charge of all aspects of drill & blast design even though a contract drilling & blasting (shotfiring) service was being provided. The major problem was that the blasting operations were yielding massive amounts of oversize due to the jointed partially weathered nature of the granite. This was adversely affecting all downstream aspects of the operation as well reducing gold output as ore boulders were being dozed over the side of the mine as they were impinging on mining productivity. The oversize problem had to be solved as the mine was struggling to achieve design gold output. Significant design & trialing effort using minesite resources were utilised to reduce the oversize but this failed even when powder factors up to 1kg/bcm(1.68lb/yd) were used. Dyno Consult from Dyno Nobel were therefore called to investigate, review & trial options to reduce oversize from the top flitch.

Jan 1, 2003

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, the National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.

By B. C. Peterson

Calumet Division, Calumet & Hecla, Inc., whose operations are in Houghton and Keweenaw Counties, Mich., is a highly integrated and complex organization. This division operates mines, a railroad, a concentrating mill, a reverberatory smelter, and the auxiliary generating plants and shops to service these operations. In addition, it operates a sands reclamation plant, leaching plants, a foundry, and a machine shop that serves varied industries with castings and parts for many applications. Calumet & Hecla, Inc. has produced over 60 percent of all the copper that has been produced in Michigan since discovery of the ore in 1864, and in 1959 the company ranked eight among the country's producers with a production of 17,407 tons. To keep abreast of modern accounting systems developed elsewhere in industry and to combat increasing costs due to higher labor and supply costs, as well as increased costs due to deeper mines and lower grade ore, the company has developed a modern machine cost accounting system. This not only provides the usual bookkeeping and cost accounting facilities but offers accurate cost data for engineering evaluation of the mining operation. This system is credited with being instrumental in permitting continued operation of these high-cost mines in a period of increasing costs with no corresponding increase in the price of metal.

Jan 1, 1962

By C. E. Wood

[Because of the renewed i~,ortanc of the strate ic netal ~ngane8e the Bureau of Mines is conductin further ro~aarch on pyrometallurgica1 ~ethods of boneficiating 0 ngani.foro'l iron ores nnn lo\,f-~~r de oanganesc ores. Published data on .the l2~roI'let llurgica.l treatnent of tl::1.nganse8 ores have been revi .. \-'en by Jose-ph ? .2]

Jan 1, 1940

Silica reacts with cryolite at 1010°C in two stages. The first stage is the formation of a sodium aluminosilicate of composition consistent with the mineral jadeite (Na20.AI20s.4Si02). The formation proceeds by atleast two different reactions. Formation of alumina or an aluminosilicate proceeds to its limiting value in the first 30 min while the formation of jadeite proceeds at a steady rate until quantitative conversion is achieved after 150 min. The net overall reaction can be expressed by the equation 6 Si02+2 Na3AlF6? (Na20.AI20s.4Si02) +2 SiF4 +4NaF.The second stage involves a slow reaction that proceeds with the evolution of a little SiF4, The net result is the formation of sodium aluminosilicates that are soluble in 30 per cent AlCIs-HCI solutions. While this could be explained by disproportionation of jadeite to form albite (Na20.Al203.6Si02) and nepheline (Na20. AI203.2Si02), it is more likely that it is due to further but limited reaction between the oxides and fiuoroaluminates.

Jan 1, 1972

Observed mineral assemblages in the Mt. Lyell copper deposit can be correlated with phase equilibrium investigations in the systems Cu-Fe-S and Fe-Zn-S. The trend of crystallization (or paragenetic sequence) of the ores is reflected in a progressive increase in the Cu: Fe and metal: sulphur ratios of the assemblages. This trend agrees with the regional zoning of the district. Tentative relationships between the paragenetic sequence, sulphur vapour pressure, and temperature are presented graphically. The absence of a suitable geological thermometer prevents precise elucidation of the range of temperatures and pressures which existed during crystallization.INTRODUCTIONRecent phase equilibrium investigations of metal-sulphur systems at the Geophysical Laboratory, Washington, D.C. provide valuable information on the stability relations of a number of important sulphide minerals. This data, when applied to natural ore deposits, may be expected to clarify two special problems which confront the ore petrologist seeking to interpret observed data in terms of a particular physical and chemical environment of ore deposition. These two problems are the sequence of formation of sulphide minerals (commonly designated the paragenetic sequence) and an elucidation of the range of temperatures and pressures which existed during crystallization. The object of this paper is to make such an interpretation of the copper mineralization of the Mt. Lyell district, Queenstown, Tasmania.The following abbreviations are used in this paper:py = pyrite, cp = chalcopyrite, en = cubanite, bn = bornite,cc = chalcocite, cv = covellite, dg = digenite, id = idaite,po = pyrrhotite, v = sulphur vapour.GEOLOGICAL SETTING AND MINERALIZATIONThe general geology of the Mt. Lyell district is well known through the recent work of Wade and Solomon (1958). The host rocks are a series of quartz-chlorite-seri-...

Jan 1, 1963

By Albert Sauveur

It is delightful to read a technical paper like that of J. E. Johnson, The Effect of High Carbon on the Quality of Charcoal-Iron, presented in October, 1912, at the Cleveland meeting of the American Institute of Mining Engineers.' The clear, simple, and straightforward manner in which he describes his experiments and results makes you feel as if you had been, so to speak, at his elbow during the course of his investigations, while his method of procedure is so rational that you can fairly anticipate each step in the logical sequence of the tests performed. The following notes suggested by Mr. Johnson's paper are presented here in the hope that they may help, if only a mite, towards the final solution of a problem of considerable scientific and industrial importance. Physical Properties of Cast-Iron us. Its Ultimate Composition. Mr. Johnson writes that " an investigation along the lines of consumption showed that different irons have different characters totally independent of their analyses," and he declares that " the presence or absence of these elements [meaning carbon, phosphorus, silicon, and manganese] alone will not account for all, scarcely for a half, of the facts which have long been known." He further tells us that some foundries have " proved, by the most irrefutable tests, that they could take a certain iron of a given analysis and produce certain results," while with " another iron of the same analysis they could not produce these results at all." I feel confident that every experienced and thinking metallurgist will readily believe Mr. Johnson's statements and will share his views in regard to the hopelessness of inferring the

Jan 1, 1914

By F. Sillers, R. T. C. Rasmussen

"INTRODUCTION This is the third report of investigations by the Bureau of Mines in cooperation with industry to establish the value of electrolytic manganese in the manufacture of ferrous and nonferrous alloys. The manganese was produced by the Bureau at its Boulder City pilot plant from domestic ores and by the process developed by it. 4/ The work was done under the direction of R.S. Dean, assistant director, Bureau of Mines, and R. G. Knickerbocker, chief, metallurgical branch. The first report dealt with the use of electrolytic manganese in the manufacture of stainless steels 5/ and the second with its use in acid electric or open-hearth low- and medium-carbon steel castings. 6/The present report treats of the use of electrolytic manganese in the manufacture of low—carbon rimmed and killed steels. A résumé of these three investigations and two others appeared in the magazine STEEL. 7/ Further reports will be published as tests are completed at some 70 industrial plants. All tests were made on full—scale heats or melts, and the resultant product was processed and used commercially."

Jul 1, 1945

The assistance that can be gained by the use of aerial photographs in the geological examination of a mineral field is clearly illustrated by the results of a rapid reconnaissance survey of the newly-discovered Mount Fitton talc, deposits, situated in the north-eastern extension of the Flinders Ranges in South Australia.The talc deposits were found to occur about the margins of a large lenticular mass of dolomitic marble, interbedded with hornfelsic tillites and fluvio-glacial sediments of Upper Pre-Cambrian age. Aerial photographs show clearly the extent of the dolomitic marble on which the growth of a species of eucalypt-Eucalyptus Gillei-is prominently developed, and which assists in defining the limits of this relatively light-coloured formation. (See Fig. 1).Upon field investigation it was found that the talc, deposits are related closely to the margin of the dolomitic marble where the latter has been subject to minor folding and faulting. The deposits themselves have been formed by metasomatic replacement of schistose dolomite. The contact of the dolomite with the underlying and overlying glacial beds is also noteworthy for the presence of minor occurrences of copper, silver, lead and zinc minerals.An examination of photographs covering a wide area reveals an outcrop of a massive granite to the north-east of the dolomitic marble, Fig. 2, which was almost certainly responsible for the regional metamorphism of the dolomitic and glacigene sediments, and the source of the mineralising solutions.All these features, as well as the broader structural features of the area, which are extremely important in the understanding of, individual commercial depQsits, were quickly determined with the assistance of the photographs.It is useful, briefly to relate the procedure adopted in examining this recently developed field as an example which may be well worth following on other fields, even if exposures are not so clearly defined. The method to be outlined, of course, will be of maximum advantage. Where rock exposures are good, where the ore bodies are likely to be widely spread, and where such bodies are related to some major geologi-cal control. Typical of such deposits are pegmatitic, hydrothermal and related ore bodies associated with the periphery of an igneous intrusion, or ore bodies related to particular sedimentary horizons in a regionally metamorphosed province.Procedure.The first requirement is the preparation of a detailed reconnaissance geological plan of as large segment as possible of the potentially mineralised province. The use of aerial photographs is par...

Jan 1, 1950