Search Documents

By J. S. Peterson, G. P. Cole

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center (PRC), has conducted research to improve electrical fault detection on coal mine direct current (dc) trolley systems. Present circuit breaker protection systems are current-magnitude-based and cannot discern between normal traffic and high resistance electrical faults. Tests were conducted at cooperating mines to assist in developing a neural-network-based detection algorithm for distinguishing between electrical faults and normal operation. The Fast Fourier Transform of the trolley rectifier current signature served as baseline data for the neural network. During field tests, the algorithm performed with greater than 90% accuracy.

Feb 24, 1997

Laboratory induced polarization measurements were made on representative samples of concentrated sulphide ores from three environments in New South Wales Comparisons were made with the membrane polarization exhibited by an argillaceous sandstone. The sulphide samples showed a strong polarization effect, the magmtude of whIch depended directly on the conductivity of tlIe pore electrolyte.

Jan 1, 1969

By Prosser A. P

The conditions under which vanadium is rendered insoluble by silica in the alkali-roast process have been investigated starting with both slag and reagent-grade materials. The inert phase is a glass formed slowlyfrom soluble NaV03 produced at lower temperatures. It contains approximately 30 per cent V in a partly reduced state; iron is not a principal component. Some of the vanadium in the inert phase is slowly returned to a soluble form by heating in an oxidizing atmosphere below the temperature at which the glass is formed (750°C). As the reaction leading to the required, soluble form of vanadium is also slow between 600 and 750° optimization and control of the temperature profile and atmosphere in the furnace, and the residence time of the solids, are necessary to ensure high vanadium extraction during subsequent leaching.

Jan 1, 1976

By A. R. Gaba

Phase I of the Canary Wharf development in London's docklands involves the construction of six fifteen storey buildings located predominantly over water of the West India Docks. The buildings are supported on some 1000 No., 25m long, open ended steel tubular piles driven through 10m of dock water to found in dense sand at a depth of about 15m below dock bed level. The piles are of composite section with reinforced concrete within the upper 17m of the steel tube. Three trial piles were installed in the dock to investigate the driveability and performance of the driven steel tubular piles. The piles were subjected to dynamic and static load testing. Loads were applied in both vertical and horizontal directions. Vibrating wire strain gauges were installed on the inside of the steel piles, on the reinforcement and in the concrete to determine the relative proportions of the applied load carried by the steel tube and concrete infill and to establish how these proportions varied along the length of the piles. Inclinometers were also installed to monitor the lateral deflection of the piles. This paper describes the driving, construction and testing of the three trial piles. The results of the vertical and horizontal loading tests are discussed and comparisons are made between dynamic and static tests carried out on the piles.

Jan 1, 1989

By Z. T. Bieniawski, José Miguel Galera, Benjamín Celada

TBM case histories from over 400 tunnel sections are analyzed presenting a comprehensive application of the Rock Mass Excavability (RME) index (Bieniawski et al.2006). The paper introduces two new adjustment factors, called the Factor of Tunnel Length and the Factor of Crew Effectiveness, which were established to represent more realistically the interaction of the rock mass characteristics, the TBM parameters and the performance of the crew operating the machine. A new correlation is provided for predicting the average rate of advance of double-shield TBMs working specifically in the double-shield mode.

Jan 1, 2007

By R. J. Robbins

The mechanization of hard rock underground mines offers a large potential for reducing cost, improving efficiency, and increasing profitability. However, in spite of serious efforts by quite a number of equipment developers and mining company initiatives, the industry has achieved little real progress. The task is difficult and the blasting alternative to mechanical excavation is an effective and well-developed method, which continues to improve in spite of its inherent limitations. A large number of machines have been built and tried. Only a few developments have succeeded to make a major impact on underground hard rock mining. It is certain that hard rock mines would be laid out and designed quite differently if the mining engineers knew they had available continuous mechanical excavation machines. In the absence of the machines, mines will be designed for excavation by traditional methods. It is not easy to utilize mechanical excavation in a mine which is designed to operate with normal drill and blast excavation. This is certainly an impediment to machine development. But what if an ore body cannot be mined conventionally, simply because the mining company cannot get permits to satisfy the ever increasing strict EIS requirements of the general public and governmental agencies? This may provide the incentive necessary to develop the equipment that will be needed by a new mining method that will have almost no impact on the environment.

Jan 1, 2001

By Andy Fortin, Jeet Basi, Simon Hille

Goldcorp’s Eleonore mine is situated in Ell Lake area in the northeastern part of the Opinaca reservoir in the James Bay region of Quebec. The design of the 7000 t/d process plant includes crushing, grinding, bulk sulphide flotation, separate concentrate and tails leaching and detoxification circuits and residue handling. Detoxified flotation tails are thickened and filtered. A portion of the filtered tails are blended with the thickened detoxified sulphide concentration for paste backfill. The remaining filtered tails are trucked to the waste management facility. This presentation will describe the challenges faced with the commissioning and subsequent ramp-up of the flotation tails filter plant and the successes achieved by the multi-discipline team at Eleonore.

Jan 1, 2016

By Orr C. W

In previous papers (1, 2), the influence on the creep resistance of elements normally found in commercial lead has been recorded. The results in the present paper refer to the influence of calcium, an element which is not found naturally in lead, but which has been used commercially in the form of alloys. It was realised that calcium would act as a deoxidising agent for lead-and in fact it was with this feature in view that both calcium and magnesium were used as additions. Subsequent work (including the results given in the present paper) has tended to diminish the importance which at first seemed to be associated with the presence of oxygen in lead. The structure of the dilute calcium lead alloys has been worked out in detail (S) and the phase diagram shows the existence of limited solid solubility and a compound CaPbs.

Jan 1, 1938

By Oliver Bowles

Sandstone, a widely distributed siliceous sedimentary rock, is the third most popular building stone in the United States. It is formed by the breaking down of preexisting rocks by weathering, subsequent segregation of the detrital quartz grains into discrete deposits by the sorting action of water or wind, and finally cementation of the quartz sand into a coherent rock. The homogeneity and resistance to weathering of the resultant sandstone make it suitable for exterior construction. Its excellent wearing properties explain its popularity for flagging and stair treads. However, quarrying and dressing methods and costs are adversely affected by the abrasiveness and hardness of sandstone especially as compared to limestone.

Jan 1, 1963

By M. K. Larson

The U.S. Bureau of Mines conducted a study to evaluate support interaction between conventional bolts and the rib at two Western coal mines. The principal goal was to develop guidelines for designing rib support under various conditions. At mine A, seven rib bolts were installed with load cells and monitored over a 4-month period. Fifty-seven pull tests were conducted with two types of anchors at various depths. At mine B, 163 pull tests were conducted. Results showed that during the 4 months of monitoring bolt load, tension in the bolts decreased over time in some situations and that anchorage capacity was reduced in a yielded zone. Load-versus-deformation plots from pull tests in the rib showed fundamental differences in anchorage behavior at the two mines, particularly when comparing results of tests in old pillars at mine A and tests in new ribs at mine B. Numerical modeling experiments indicate that coal bonding strength was the most significant factor in determining postyield anchorage capacity. Correlation of anchor yield point with anchor depth were more pronounced at mine A than at mine B; measuring torque may be a reasonable method of monitoring deteriorating anchorage capacity in a rib undergoing fracturing and yield.

Jan 1, 1996

By Nicol S. K, Swanson A. R

The poor flotation response of many coals has in the past been attributed to such factors as differences in rank, differences in degree of oxidation, differences in petrographic composition, or slime coatings. The present work shows that while all these factors undoubtedly influence flotation, the size distribution of the feed may override these. Evidence is presented which shows how this factor can lead to substantial losses of coarse coal (>250 µm)from a coal which would normally be considered amenable to flotation. Reasons for this loss of flotation response are suggested together with means of overcoming the problem.

Jan 1, 1978

By Chikaosa Tanimoto

INTRODUCTION Bratislava is located at the intersection of important traffic routes, including motor-ways, roads, railways, air traffic, trading, and inland waterway with an important harbour. The construction of the D2 Motorway Bratislava, Lamacska cesta Stare grunty was the last missing section of D2 Motorway and its completion linked the Czech Republic through Bratislava to the Hungarian Republic. Traffic was obliged until its completion to use the Lamacska Road and Mlynska Dolina, which were the most heavily trafficked roads in the city. The section of D2 Motorway to be completed in 2006 was 3,300m in length, of which the SITINA Tunnel was approximately half the length. After putting into operation the transit traffic(motorway) and urban traffic was separated. Transit traffic by passing the town was eased. The junctions D2 with Lamacska Road (Harmincova) and Mlynska Dolina also allowed better use of the motorway for the urban traffic The tunnel construction was specified by the features with the highly weathered and thermally altered granitic rock formation with the overburden of Quaternary sediment of 2?4 m thick, very thin overburden, severely controlled deformation limit and environmental protection. The tunnel had to be excavated beneath and nearby the academic complex area and the zoo, where sensitive facilities exist and animals live in. The tunnel consisted of two tunnels (Tunnel A and B) with the length of 1,415 and 1,440 m, respectively. The overburden thickness was in the range from 10?30 m. The standard cross-section and the one with invert arch were 79.5?81.5 m2 and 92.1?93.3 m2. The excavation took 21 months from September 2003 to May 2005. The construction was based on the concept of NATM. The SITINA Tunnel was the third application of NATM in Slovakia, following the BRANKISKO Tunnel (commenced in July 2003) as the first and the HORELICA Tunnel (in October 2004) as the second NATM practice. To protect the surrounding structures and citizens from tunneling operations, seismic monitoring was performed in association with blasting. The allowable limit of blasting vibration was fixed to be under the particle velocity of 15 mm/sec. The tunnel excavation cleared this limit as expected before construction. In driving through the difficult geological situation the excavation work hit 49 faults, and some of them occasionally caused serious face instability. In principle, the rock formation has been affected by the high hydrothermal effect and the resultant clay filing along faults and joints. The auxiliary reinforcement with the 4?8 m long pipe roofing was needed to protect the vicinity of mining face area. This operation extraordinarily required additional works and time which had not been expected before construction.

By O. Celep, T. Uslu, Savas

This study investigates the enrichment of a low-grade colemanite concentrate (-3 mm) using a Knelson centrifugal gravity concentrator. Due to its low boron content, the concentrate is unsaleable and has to be stored under appropriate conditions to avoid potential environmental problems. The low-grade colemanite concentrate was comminuted to size fractions of-1 mm, -0.5 mm, and -0.15 mm before treatment in the Knelson Concentrator. The effects of particle size, fluidizing water velocity, and bowl speed on the enrichment process were examined. The B2O3content of the concentrate was increased from 33.96% to a maximum of 45.52%. B2O3recovery increased with increasing bowl speed and particle size, and decreased with increasing fluidizing water velocity. The enrichment process also rejected arsenic and iron to some extent, with a maximum reduction of arsenic from 1360 g/t to 765 g/t and iron from 0.88% to0.33%.

Jan 1, 2015

By Steve Kral

The mining industry has had three difficult years. Commodity prices have remained low and investor confidence in the industry has been shaken. And even though the Asian economy appears to be improving, it will be some time before this improvement will translate into better commodity price conditions for mining. In addition, increased environmental and social restrictions that have been placed on the industry in developed and developing countries have made mining a more difficult proposition. And, if that is not enough, the global mining industry has found itself in fierce competition with Internet businesses for investor capital. Despite that gloomy picture, more than 10,500 mining industry professionals from about 70 countries gathered in Toronto, Ontario March 5-10, 2000 for the Mining Millennium 2000 conference. This meeting was a joint effort between the Canadian Institute of Mining, Metallurgy and Petroleum(CIM) and the Prospectors and Developers Association of Canada (PDAC).The joint meeting also featured two trade exhibitions and more than 150speakers. PDAC’s trade show attracted about 400 exhibitors and an additional 200 in the concurrent Investors’ Exchange. CIM’s exhibition attracted about 600 equipment and service companies.

Jan 1, 2000

Removal of Arsenic in Enargite from Copper Ores by Flotation and Leaching in NaHS Media

Sep 13, 2010

By G. R. Peterson

To determine the availability of lead and zinc from demonstrated resources, the Bureau of Mines evaluated 235 mines and deposits in 31 market economy countries. Of the 235 mines and deposits evaluated for this study, 186 were evaluated as zinc operations, 30 as lead operations, and 19 as copper operations. Demonstrated lead-zinc resources of market economy countries in 1981 were approximately 4.3 billion metric tons (t) of ore containing 221 million t of zinc and 97 million t of lead. Of these amounts, approximately 154 million t of zinc and 70 million t of lead are estimated to be recoverable. The analyses indicate that demonstrated resources in market economy countries should be sufficient to satisfy projected demand for primary lead and zinc through the balance of the century. The U.S. lead industry will continue to have a comparative advantage over the rest of the world industry, barring any drastic increase in the cost of compliance with pollution control regulations. It appears that the comparative disadvantage faced by the U.S. zinc industry will probably intensify owing to the relative quantity of lower cost zinc resources in other countries, especially Canada, Australia, Mexico, and Peru.

Jan 1, 1985

By W. A. Wood, H. M. Bendler

Cylindrical fatigue specimens of OFHC* copper were subjected to alternating torsion while under axial tension. The superimposed tension strongly influenced the fatigue life of the specimens as well as causing characteristic changes in the structure of the fissures that form and develop throughout the life of the specimen. A further effect of the superimposed tension is a continuous extension of the specimen throughout its life in a manner formally similar to creep at elevated temperatures. RECENTLY, studies of the structural changes leading to fracture of metals by fatigue have been made by a technique which reveals, in section, the lattice distortion arising from slip movements inside the metal and the disturbances built up by these slip movements at the metal surface.1'2 According to this approach, fatigue develops as follows: a) fine slip movements concentrate in bands, producing little strain-hardening and thus permitting abnormal totals of plastic strain before fracture and, therefore, abnormal amounts of lattice distortion along each slip band; b) both forward and backward slip movements occur in each band which, according to their distribution across the band, may build up surface disturbances that include sharp notches; c) these notches early in the life of a specimen penetrate the distorted slip zones and transform them into deep, fine fissures; d) the fissures on continued cycling locally saturate the metal and cause local collapse in the form of a microcrack. Thus, the significant consequence of fatigue or cyclic

Jan 1, 1962

By Matthew A. Baumann

Tooth-wear on mining shovels requires continuous monitoring. Worn teeth impede excavation performance, increase energy usage, and increase the risk of lost or broken teeth and adapters. A machine-vision-based automated tooth-wear monitoring system is presented. The system employs a rugged boom or stick-mounted camera to capture images of the shovel teeth. An onboard computer processes the images in real-time to determine the length of each tooth. The current wear state is available via a network-accessible log for on-demand status updates. By continuously recording tooth length changes over time, the logs can be used to estimate wear rates and patterns, permitting comparisons between different G.E.T. configurations, operator behaviour patterns, or material types. This detailed, quantitative data permits site-specific optimizations to wear packages and maintenance scheduling. Automating wear monitoring offers the crucial wear information necessary to minimize maintenance costs and reduce unscheduled downtime. A 37-day field trial in a copper-gold mine demonstrated the ability of the system to measure tooth lengths, compute wear rates, and detect differences in tooth wear based on their position on the bucket.

Nov 1, 2011

By Verya Nasri, Scott Thorburn

The City of Toronto and the Toronto Transit Commission (TTC) have conducted an Individual Environmental Assessment (EA) for a 6.2 km, 4-station underground extension of the Spadina Subway from Downsview Station to Steeles Avenue. This Environmental Assessment Study was performed in three phases including routes and general station locations, alignments and station concepts and detailed assessment of the effects of the undertaking. URS Canada Inc. has led the consultant team for this Study. The anticipated total duration of the project is approximately 6 years and its estimated total cost is about $1.4 billion. This paper presents the planning process of the project, the environmental and engineering challenges, and the measures taken to address them.

Jan 1, 2007

By Lumley G, Rowlands D

The overburden slusher (OS) is proposed as a stripping tool that is expected to find application in overburden stripping operations including open cut coal and oil shale mines. OS is expected to combat the effects of increasing depth on the productivity of conventional dragline stripping.Although previously developed stripping techniques have included the use of drag scrapers the OS is sufficiently different as to constitute a new stripping method.A study undertaken at the University of Queensland during 1985 is believed to be the first major study on the use of the OS and preliminary economic results are very encouraging. It appears that the OS has the capacity to remove overburden at a cheaper unit cost than the equivalent powered dragline stripping machine at any comparable depth of overburden. The OS is not adversely affected by increasing stripping depth to the same extent as a dragline. In addition, the action of the OS machine allows for the lowering of spoil face angles, thereby reducing spoil slope stability problems encountered in deep open cut strip mines.

Jan 1, 1986