Search Documents

By T. P. Mucho

Over the past several years, two types of roof control problems have been en- countered at Beth Energy's Eighty Four Complex mine in Southwestern Pennsylvania. These problems have been (1) poor roof conditions encountered while advancing submain entries and longwall panel entries and (2) deterioration and failure of long- wall gateroads, principally the tailgate entry. This paper discusses the efforts by mine personnel to analyze the origins of the various attempts to-deal with the problems, and the success (or failure) of these efforts. Highlighted are the use of various common roof Control materials, variations in mining techniques, cementatious pillars, and changes in pillar design using yield and abutment pillars to address these problems.

Jan 1, 1986

By L. A. Stewart

This paper describes all occurrences of barite in Arizona that were known or reported to the authors. The history, ownership, production, and geologic setting are discussed for most of the deposits. The uses and specifications of product grades are briefly discussed. Seventy-five deposits were examined in 9 of the 14 counties of the State. The descriptions are given under county headings. No occurrences were reported in the four northeastern counties of Coconino, Navajo, Apache, and Greenlee, nor in Santa Cruz in the southern part of the State. From about half of the deposits examined, 55 samples were taken; of these, 45 were for chemical analysis, and 8 larger samples, ranging from 100 to 350 pounds, for beneficiation tests. A 30-ton bulk sample was taken for pilot-plant tests. Bench-scale flotation tests of the eight samples employing several different procedures and reagent combinations yielded marketable-grade barite products with barite recoveries ranging from 60 to 97 percent. Five of the samples contained enough fluorspar to warrant its recovery. Acid-grade concentrates, which accounted for fluorspar recoveries of 45 to 70 percent, were obtained from three of these ores. Batch laboratory tests of a representative portion of the 30-ton bulk sample revealed that acid-grade fluorspar and high-grade barite concentrates could be recovered. Results of the laboratory and continuous pilot-plant tests of this ore will be presented in a separate report.

Jan 1, 1960

The discussion which followed the publication of my paper by the formert has, I think, enhanced its value. It may therefore be of interest to members of our Australasian Institute, who are not members of the Institution of Mining and Metallurgy, if I give a synopsis of the discussion.My attention was drawn to the fact that my paper did not make clear the extent of the improvement in furnace operations, which followed the use of coke of high quality; this comment applied more particularly to the lead content of slag. My failure to supply comparative figures in regard to the lead content of slag was governed by a condition which, I think, is of interest to metallurgists. As a result of industrial...

Jan 1, 1932

By Gary A. Kingston

Domestic nickel resources are costed to develop a contingency supply curve of U.S. nickel availability at various costs. It is estimated that 4.3 billion pounds of nickel is potentially recoverable from 698 million tons of ore at prices ranging up to $6.36 per pound of nickel. Over 95 percent of the total is estimated to be available at a price of less than $4.00 per pound.

Jan 1, 1970

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"ABSTRACTTheoretical approach to estimate the ultimate pile capacity gives a rough idea at the initial stage of design that later on strengthen by the execution of static pile load test at site. The static pile load test is the only best option for the estimation of ultimate capacity of various types of piles. There are various methods based on strength, serviceability, net deflection for end bearing, shaft adhesion, graphical and extrapolation approaches for the interpretation of pile load test data to calculate the ultimate capacity. In this paper an attempt is made to evaluate the best-fit method for the estimation of ultimate capacity of single helix screw pile. The pile load tests on model scale were performed on screw piles of different helix diameter. The purpose of adopting model scale of testing was to achieve a state at which settlement increases without further increase in vertical load. The ground was compacted with dry sand at denser state. It was observed from the test results that extrapolation methods such as Chin- Kondner and Decourt predict the load settlement curve of screw piles very well, however ultimate pile capacity was on higher side which may not be suitable for the strength of helix plate. Decourt approach to plot the pile load data showed clear indication of the deformation of helix due to strong subsurface condition. A modified approach in Decourt method is proposed for estimating the ultimate capacity of screw pile having deformed helix whereas reduction factor is suggested for Chin-Kondner method for the estimation of ultimate capacity of intact screw pile.INTRODUCTIONDeep foundations are used to avoid the soft ground at shallow depth that is not suitable for carrying the structural load. Different types of piles have been used to transfer the load to deeper stratum. The screw pile is one of the new piling method and its use is considerably increasing. It consists of a cylindrical steel shaft with one or more helices at various length of the shaft. The diameter of helices (Dw) is usually 2 – 2.5 times the shaft diameter (Ds). The pile is installed to the required depth through torque and pressure. The advantage of screw pile over other piling system is its quick installation mechanism, high end-bearing and uplift resistance, noise reduction and minimum use of man power."

Jan 1, 2014

The mining industry to the lay mind is one which appears peculiarly dangerous, partly because the accidents which take place are usually of a very tragic nature, and partly because other, industries claim victims more from disease than fromviolence, and their fatal nature is not advertised to the same degree so that in spite of this idea of unusual risk, it is a fact that mining will compare favourably, as regards vital statistics, with nearly all other trades requiring special training.Neverthelessthere are a larger number offatal and serious accidents occurring year by year than one would like to see, and could the deaths which take place by accident be eliminated, it is safe to say that mining would become one of the most healthy of all species of skilled labour. If we examine the accidents appearing yearly in the reports of the Mining Departments of the various colonies, it will be at once admitted that many of them need riot, and in many cases ought not to, have occurred.It is, therefore, the object of tbis essay, to pass under review the ordinary precautions which should be adopted to minimise, as far as possible, the dangerous factors whereby fatalities are brought about.

By J. T. Nel

The establishment of a pilot plant for the continuous production of titania pigment and nano-titania is discussed. The plant was designed, constructed and operated on the Necsa site. The TiO2 production capacity is 7?10 kg.h-1 by the reaction of TiCl4 and O2at>1000°C. Liquid TiCl4 is sprayed under pressure into a plasma reactor where it evaporates and reacts with O2 to form TiO2. Process optimization has allowed for continuous production without any clogging or blockages. The primary advantage of the plasma-assisted process is the possibility to recover and recycle the chlorine values in high yield as Cl2 for use in the manufacture of TiCl4. The HCl formed in most conventional fossil-fuelled processes makes Cl2 recovery and recycling much more difficult. Particle size distribution analysis of the fine, white product revealed a d50= 125 nm. The raw product consisted of 60% rutile that could be increased to 80?100% rutile by post-annealing. The specific surface area (SSA) of the pigment was 8?20 m2?g-1(BET). According to the CIE colour index the ?whiteness? (L*>95) of the plasma-produced pigment was better than that of several commercially available pigments. The particle size could be manipulated by controlling the TiCl4 feed rate, gas flowrates, and the particle quench rate and residence time. Nano-sized TiO2 powders with a particles size (d50) as small as 50 nm were also successfully produced in this way.

Jan 1, 2010

By B. P. Watson

Crush pillars have been incorporated into a mechanized, low-profile trackless system at South Deep Gold Mine. These pillars had to be designed to fail near the face and to ensure that pillar failure is contained within the pillar, to avoid bursting and the risk of high loads being generated during a seismic event, respectively. PoweRite backfill bags were recommended to maintain the integrity of the pillars; except in the main access drives, where the sidewalls were to be supported on 5.6 mm diameter weldmesh and yielding anchors. The results of a trial site investigation exceeded expectations, showing a residual pillar strength of about 37 MPa for a newly formed pillar and 8 MPa for a pillar subjected to seismicity and a closure of more than 300 mm. The introduction of these pillars has improved the rock mass conditions because of the active nature of the support, compared to the previous passive backfill method. Importantly, the pillars have increased mining efficiencies and improved face availability. A potential cost saving to the mine of R140.9 million could be realized over a period of 10 years.

Jan 1, 2014

By Bin Tang, Suping Yao

In the last decade, the copper industry in China has developed rapidly and attracted the world’s attention. The production capacity of refined copper has grown remarkably from 4.578 million tons in 2010 up to 9.029 million tons in 2018, accounting for about 40% of the global refined copper production. And now, China has become the biggest refined copper producer in the world. This paper summarizes the application of modern copper metallurgical technologies such as Outotec flash smelting/converting technology, Cyclone smelting technology, TSL (ISA/Ausmelt) smelting/converting technology, Jinfeng side blown smelting and Baiyin side blown smelting technology, Chifeng side blown smelting and continuous top blown converting technology, SKS bottom blowing technology, Dongying two-step smelting technology, copper electrorefining with high current density, etc. in China’s copper industry, analyzes and compares the characteristics of those technologies and presents the great efforts of China’s copper smelters in adapting to the increasingly strict emission standards and improving economic benefits of copper smelters. INTRODUCTION China has been the biggest refined copper producer in the world for many years. China produced million tons of refined copper in 2018, accounting for 40% of the copper smelting production in the world, and of which, roughly, 70% of the copper concentrate was imported, mainly from Chile, Peru and Australia. ICSG (International Copper Study Group, 2017) shows clearly the position of top 20 countries of copper production and copper mine production (Figures 1 and 2). Blast Furnaces, Reverb Furnaces and Electric Furnaces dominated China Copper Smelting for quite long time till 1980s. The first modern copper smelting technology (flash copper smelting) was introduced into China in 1980s, then followed by Noranda, Ausmelt and ISA. Since then, China copper smelting technology stepped into modern time. Since 2000, old processes (Blast Furnace, Reverb Furnaces and Electric Furnaces) were phased out and replaced by modern smelting technologies. China Copper Production has been increasing dramatically (Figure 3).

Jan 1, 2019

Perhaps one of the most important conferences or symposia which our Institute has conducted, was the joint Aus. LM.M./AJ.M.E. meeting held in Canberra in May 1978, with the theme International Resource Management (Woodcock, 1978).We were privileged to witness active participation in the meeting by outstanding personalities from the mining and metallurgical industries of Australia and New Zealand, the United States of America, Canada and the United Kingdom and to hear addresses on subjects of international significance to the mining and metallurgical industries.Our Institute is one concerned with professionalism.The principal objects of The Institute as described by our founders include, "promoting the arts and sciences connected with the economical production of the useful minerals and metals, and the welfare of those in the industries, by meetings for social intercourse, and the reading and discussion of professional papers, and to circulate by means of publications amongst its members and associates, the information thus obtained".Sir Maurice Mawby (1968) said in his Presidential Address to the Institite, "the most important aspect of these objects was the promotion of the arts and sciences of the mining industry".Why is it then, that a large proportion of the papers given at the meeting in Canberra dealt with world wide social aspects of the mining and metallurgical industries, rather than the technology, the arts and sciences of mining and metallurgy as principal factors in international resource management?The answer is quite simple of course, and that is that the social and political factors are the principal factors which create the demand for basic raw materials and in the long term determine the costs and prices of the commodities which our professional abilities are drawn upon to produce.

Jan 1, 1979

Local conditions at Hatches Creek are described, together with the mineralogy, mining and treatment of tungsten ores, with particular reference to procedures adopted by Pimer Mines, N.L.The Hatches Creek tungsten field covers an area of about 20 square miles in: Central Australia; 285 miles' N.E. of Alice Springs. Access is by rail to Alice Springs, then by 200 miles of bitumen highway to Barlo Creek and 8,5, miles of bush track to the field. Passengers can also reach the mines by... A semi-desert climate prevails Rain; generally in the form of thunderstorms falls in the summer months: December to March. Average annual rainfall is approximately 15 inches but there is great variation from year to year, occasional droughts being followed by torrential downpours. Vegetation is sparse except in the wide creek beds. Surface water occurs in rock holes some of which, spaced miles apart, carry permanent water...

Jan 1, 1955

By Edmonds W, Jeffcoat R

The completion of the first two open hearth furnaces in the new No. 2 open hearth plant at Port Kembla will increase Australian production of steel by 350,000 tons of ingots per annum.The paper gives an outline of the essential features of open hearth design and auxiliary equipment required to operate the two modern open hearth furnaces at present being installed.INTRODUCTIONThe increasing demand for steel required by Australian secondary industries led to the decision to construct and operate No. 2 open hearth plant at Port Kembla. Two basic open hearth furnaces of the most modern design are under construction and it is anticipated that these units will be commissi.oned in September 1956. Australian steel capacity will thereby be increased by approximately 350,000 tons of ingots per annum.PLANT LAY-OUT AND CONSTRUCTIONIn the design and lay-out of this plant the emphasis has been on efficient material handling with simplicity of design and operation. Overseas methods were studied and these studies, together with experience gained at Newcastle and Port Kembla open hearth shops, enabled this plant to be built to a standard which compares favourably with any other in the industry.Initially two furnaces, each of 2,75 tons capacity, have been built, but provision has been made in. the design and lay-out to enable expansion to six furnaces.The location of the new plant in relation to the existing units will be noted in Fig. 5. It is one of the first units to be built in an area which will dovetail into a pattern for...

Jan 1, 1957

By Parker A. J, Giles D. E

Solutions of copper(II) sulphate in acidified aqueous acetonitrile leach copper from copper-lead matte derived from the drossing of lead with sulphur to produce solutions of copper(I) sulphate. The reactivity of the matte constituents towards copper(II) sulphate is Cu2S> PbS > CuS > > Pb. According to the leach conditions, part or ,all of the copper may be leached 'leaving a residue of CuS/PbS, or S/CuS/PbS04, or S/PbS04, to be recycled to the lead smelter. Complete extraction of the copper requires leaching with oxygen which occurs under mild conditions in the presence of acetonitrile and sulphuric acid in water. Copper is selectively recovered as a pure product by electrochemical or thermal disproportionation of copper(I) sulphate solutions. A notional process is proposed.

Jan 1, 1979

By Paul Gauthier

Aujourd?hui, avec un faible prix de l?or sur le marché, les opérateurs miniers doivent revoir leur façon de faire. La méthode de minage «Eureka» permet de réduire les coûts de production et d?accélérer la mise en production des chantiers. Les principales étapes du cycle de minage et les problématiques associées à l?utilisation de cette méthode à la Mine Bousquet y sont décrites.

Oct 1, 2001

By Murray Jacobson

Facts obtained by the Bureau of Mines on the dust-explosion hazard in air of materials used in the plastics industry are presented for 313 samples studied in the laboratory. Information is given on ignition temperature of dust clouds and layers, minimum explosive concentration, minimum energy required for ignition, explosion pressure and rates of pressure rise, amount of inert dust required to prevent ignition and flame propagation, and, in some instances, on the limiting oxygen concentration in an atmosphere to prevent ignition by spark and by heated surface. The effects of particle shape, additives, and resin structure on explosibility are discussed. Relative explosibility of the materials is related to the ignition sensitivity and explosion severity and is denoted by an empirical index. Recognition of the degree of hazard will facilitate adoption of adequate measures for preventing ignition and explosion during manufacturing or processing.

Jan 1, 1962

By M. Sadegh Safarzadeh, Stanley M. Howard

The two-dimensional predominance area (Kellogg) diagram (PAD) surfaces bounding the three-dimensional Cu-As-S-O system were constructed at 900 K. The computations employed gases As4O6(g), O2(g), and SO2(g) as the independent coordinate species to generate diagrams of As4O6(g) − O2(g),O2(g) − SO2(g), and As4O6(g) − SO2(g), while the third gas (As4O6, O2, or SO2) was fixed. The results indicate that there is no shared boundary between enargite (Cu3AsS4) and copper sulfate (CuSO4); however, at PO2 < 10−6 atm, PAs4O6 < 10−10 atm, and PSO2 > 10−4 atm, CuSO4 is the stable phase at 900 K. The chemical driving force for oxidation of intermediate phases between enargite and copper sulfate is substantial except for basic sulfate (CuO · CuSO4).

By M. Sadegh Safarzadeh, Stanley M. Howard

The two-dimensional predominance area (Kellogg) diagram (PAD) surfaces bounding the three-dimensional Cu-As-S-O system were constructed at 900 K. The computations employed gases As4O6(g), O2(g), and SO2(g) as the independent coordinate species to generate diagrams of As4O6(g) − O2(g),O2(g) − SO2(g), and As4O6(g) − SO2(g), while the third gas (As4O6, O2, or SO2) was fixed. The results indicate that there is no shared boundary between enargite (Cu3AsS4) and copper sulfate (CuSO4); however, at PO2 < 10−6 atm, PAs4O6 < 10−10 atm, and PSO2 > 10−4 atm, CuSO4 is the stable phase at 900 K. The chemical driving force for oxidation of intermediate phases between enargite and copper sulfate is substantial except for basic sulfate (CuO · CuSO4).

The selection of the best comminution circuit for the preparation of concentration feed is a compromise based on economics, energy efficiency, labour costs, steel consumption, availability and other factors specific to each case. It is postulated that the selection must be a choice of one of the eight basic comminution circuits which can be divided into two basic groups, (1) autogenous or semi-autogenous primary mills with or without a secondary grinding stage and (2) fine crushing usually in cone crushers followed by a rod mill-ball mill circuit or a single stage ball mill circuit. The accuracy of selection may be improved by pilot plant and laboratory tests which are described in this paper. For (1) above, testing includes media competency tests with standard impact crushing, grindability and abrasion tests followed by pilot plant tests. For (2) above, bench scale crushability, grindability and abrasion testing is available. It is suggested that, through these tests, it should be possible to eliminate all but one in each group of basic comminution circuits. Then engineering and economic studies should lead to the best comminution circuit for the specific requirement.

Jan 1, 1984

By R. N. Powell

The Pipeline ore body was discovered in March 1991. The construction of the new mine and mill did not start until early March of 1996. Upon completion of permitting and corporate project approval, the 289 million USD project was “fast tracked”. The commissioning began 11 months after start of construction and the project ended 40 million USD under the budget figure. The objective of this paper is to review and highlight the Pipeline Project history from discovery, design, lawsuits, permitting, and re-design through to current - 1998operating practices. Particular emphasis will review the process design, design mistakes, and design successes. The paper will review project history, feasibility, design concepts, operator training, construction, financial and the current operation. Additional discussion will review what design features worked and which did not work within the process plant.

Jan 1, 1999

By Nageswararao K

A series of tests was carried out on one of the rock-pebble milling circuits treating complex nickel ores at Kambalda Nickel Operations of Western Mining Corporation. A mathematical model to describe the behaviour of a 508 mm hydrocyclone was developed from the data.A &quot;flat&quot; reduced efficiency curve was observed for the system. This was attributed to a marked difference in the specific gravity of different size fractions of the feed. A modified approach in describing the shape or the reduced efficiency curve resulted in accurate prediction of the hydrocyclone performance.

Jan 1, 1981