Search Documents

By P. H. Floyd

This report presents the results of laboratory and continuous mill-beneficiation tests conducted at the Bureau of Mines Northwest Electra Development laboratory, Albany, Oreg., on nonsulfide lead ore from the Sherman mine, Leland district, near Burke, Idaho. The predominant lead-bearing mineral in the ore sample treated was pyromorphite, a minor ore mineral of lead. Known reserves of pyromorphite lead ore in the United States are limited, although an appreciable tonnage of this type of ore is found in the Sherman mine. Very little pyromorphite is being mined in this mine or in the United States. This beneficiation problem presented a unique opportunity to study the mineral-dressing properties of a less widely known lead mineral, and consequently adds valuable knowledge to the ways of beneficiating ores containing nonsulfide lead values. This mineral-dressing problem was successful with conventional concentration methods of flotation and Gravity separation.

Jan 1, 1952

By H. D. Kline

This publication describes mining and milling methods and costs at the Madison mine of National Lead Co., St. Louis Smelting & Refining Division, in the Fredericktown district of southeast Missouri and is one of a series prepared by the Federal Bureau of Mines on methods, practices, and costs of mining and milling throughout the United States. The are bodies of the Madison mine are known for the complexity and diversity of their are minerals. Sulfides of copper, nickel, and cobalt occur in commercial quantities with lead sulfide, which is the most valuable metallic mineral in are bodies of the Bonne Terre formation in southeast Missouri. Several attempts were made by various operators to mine the complex ores and separate the sulfide minerals before 1927 when National Lead Co. became interested in the Fredericktown district. Operating then as the St. Louis Smelting & Refining Co., the company began mining and milling ores from the Madison mine in 1944 and has operated continuously since then. A recently built refinery produces copper, nickel, and cobalt metal from a concentrate containing iron sulphides and small quantities of copper, nickel, and cobalt sulphides.

Jan 1, 1961

By F. Nelson

RJB Mining is the largest coal producer in the UK. In January 1995 the Company acquired the Central North and Central South Regions of British Coal consisting of: ? 15 operating collieries -including capital equipment ? 2 care and maintenance mines ? 16 operating Opencast sites ? Interest in 26 prospective and 46 potential Opencast sites ? Approximately 417 million tonnes of proven and probable reserves and considerable mineral resource ? 9 million tonnes of coal stocks ? Long term contracts to supply approximately 90 million tonnes of coal to National Power and PowerGen to the period of 3 March 1998 ?Approximately 7,600 employees and 4,500 mining contractual labour. Up to the acquisition RJB Mining had the capacity to produce 14 million tonnes of saleable output with an approximate 1,500 strong workforce.

Jan 1, 1998

By R. J. Fantel

The Bureau of Mines investigated the resource availability of titanium minerals from 63 mines and deposits in 12 market economy countries. These mines and deposits contain, at the demonstrated resource level, an estimated 438 million metric tons (mt) of titanium dioxide (TiO2) in the minerals rutile, ilmenite, leucoxene, and anatase. An additional 314 million mt of TiOz is available from inferred resources. If all titanium minerals and other recovered heavy minerals are sold at total costs at least equal to the January 1984 market prices, approximately 200 million mt of contained TiO2 could be recovered in total. In terms of mineral concentrates, this equals approximately 11 million mt of rutile concentrate, 187 million mt of ilmenite concentrate, 3 million mt of leucoxene concentrate, 13 million mt of synthetic rutile concentrate (in addition to the ilmenite), and 89 million mt of titanium slag. The study indicates that world resources of low-cost rutile are declining. In order to maintain future supply for high-grade titanium resources, alternate sources will need to be developed, which may include higher cost rutile mines, Brazilian anatase deposits, increased production from slag operations, or more synthetic rutile capacity from ilmenite resources, which are abundant.

Jan 1, 1986

By LaTasha R. Swanson, Jennica L. Bellanca

Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which present an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current research study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders’ evaluations. The study includes considerations and suggestions for safe technology integration

By LaTasha R. Swanson, Jennica L. Bellanca

Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which present an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current research study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders’ evaluations. The study includes considerations and suggestions for safe technology integration

Reliable estimation of in situ stress is a major step in the analysis and design of underground excavations in rock, particularly for evaluating the stability of underground structures to prevent failure or collapse. In the last ten years, the Western Australian School of Mines (WASM) has studied and developed an AE stress measurement technique using orientated core named the WASM AE method. It allows the determination of a representative and detailed knowledge of the in situ stress field during the early stages of a project (such as mine feasibility studies), even in areas where development access is not yet available. The method has been used for in situ stress measurement at more than 80 mine sites worldwide with over 200 individual stress measurements carried out to date. This paper describes the sample collection, sample testing and reconciliation of results for very deep measurements carried out at the Craig-Onaping mine complex in Sudbury Canada. The results constitute the deepest measurements undertaken to date at the WA School of Mines and indicate that the main principal stress is horizontal and oriented parallel to a common regional sub trend in a NE/SW direction.

May 1, 2009

By Ware AR, Doyle BJ, Hoogvliet H

The Ladolam deposit lies within the altered volcanic rocks of the caldera floor, part of which now forms Luise Harbour. It was discovered in 1982 in the course of a reconnaissance drainage sediment sampling programme. This was designed to follow up indications of surface hydrothermal activity noted by Government geologists during an earlier survey of the Tabar-Feni island chain. Diamond drilling began in September 1983 and by the end of 1989 a payable and proved mineable reserve containing 19 million ounces of gold had been established. Rock types and structures are masked at the surface by intense alteration and weathering. An extensive drilling programme has enabled the identification of these features and the relationships between them necessary for an understanding of the factors controlling gold mineralisation. It has also led to the recognition of two distinct phases of alteration. The first phase of porphyry-style potassic alteration was followed by violent caldera formation, producing extensive brecciation and veining. The second alteration phase partly over- printed the first phase and was an epithermal one, evidenced by argillic, advanced argillic and phyllic assemblages. During this event, a large volume of fluids circulated under the favourable structural conditions; these fluids included a sulphur- rich, neutral chloride brine believed to have transported the gold. Boiling and mixing of circulating fluids in the open breccias is thought to have resulted in deposition of the gold. There is evidence that this process is continuing at the present day.

Jan 1, 1991

By Alain Bouchard, Germain Labonté, Jim Barrett

"Mill feed materials that are not run-of-mine ore are often a challenge for mineral processors and tend to accumulate in stockpiles, where they remain unprocessed for many years and become “slow moving inventories”. During a complete re-evaluation of the Clarabelle Mill operation (38,000 ton/day capacity) in 2000, it was concluded that there was an opportunity to assemble a 5,000 ton/day custom circuit to treat such stockpiles in the equipment that remained available during regularly scheduled maintenance shut-downs.This project was part of the larger Mill Redesign Project and involved testing the intended flowsheet under a number of operating scenarios for the first material to be treated: spent refractory bricks. The laboratory focus was on how to maximize returns using the available equipment and reagents.The circuit was successfully commissioned in the fall of 2000. As the brick stockpile was depleted, other potential feeds were evaluated at the laboratory, as well as in the new custom circuit itself. Processing of the spent refractory brick has yielded a significant contribution to the profitability of INCO. Significant opportunities lie ahead for generating more value from other slow moving inventories.INTRODUCTIONIntegrated mining operations tend to have slow moving inventories along the path from the mines to the finished products. Spent refractory bricks from furnaces and converters and furnace bottoms are materials that often end up in long-tern stockpiles. Such stockpiles are a challenge, although they represent small tonnages on an annual basis, because they are unique materials, which cannot be readily brought into the process at a rate anywhere near that at which they are produced, due to the high contents of deleterious components such as chromite or magnesia. Accumulation over years will eventually yield a metal inventory worthy of consideration given the right opportunity, such as availability of spare equipment or peak metal prices."

Jan 1, 2002

By S. Banisi, M Nesari, J. A. Finch, N. Nobari, H. Javani

"The flotation circuit of the Sarcheshmeh copper mine, which processes 40,000 t/d of ore at 0.9% Cu, consists of rougher, cleaning and recleaning stages. Mechanical flotation cells are used in all stages. To investigate the amenability of flotation columns in the plant especially for cleaning and recleaning stages, a column was designed, constructed, and installed at the Sarcheshmeh pilot plant. The pilot plant, which has an identical circuit configuration compared to the plant, can process up to 2 t/h of ore. The overall rate constant of the ore along with the target recovery of 94% were used to size the column. A 26 cm by 550 cm column with two filter cloth spargers and a submerged froth washing system using perforated tubes was constructed. To detect the interface level a 180 cm conductivity probe consisting of 1.5 cm diameter ring electrodes was installed. The tailings flowrate controlled by a variable speed pump was used as the main control variable. The initial testing program revealed that the optimum superficial gas and wash water flowrate were 1.5 and 0.3 cds, respectively. It was observed that the cleaning stage grade when using the column could increase by 2-3% at constant overall copper recovery.IntroductionThe Sarcheshmeh copper ore body which may rank as third or fourth largest in the world contains 1 billion tomes averaging 0.90 % copper and 0.03 % molybdenum. It is in located south-east Iran and has been processing 40,000 t/d of ore since 1982. After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailings constitutes the main component of the plant final tailings. A concentrate with an average grade of 31% Cu (chalcopyrite and chalcocite) is obtained after cleaning and re-cleaning stages in mechanical cells. Total recovery of the plant varies between 83-87 % depending on ore type and operating conditions."

Jan 1, 2000

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2000

By Pierre Rocque

The Red Lake Mine is located approximately 600 km northwest of Thunder Bay. This 545 tpd (600 tons/day) underground narrow vein gold operation is set to produce in excess of 14.8 tonnes (475,000 ounces) in 2001 at a cash operating cost below 75 U$/oz. The high-grade nature of this deposit (>55 g/t or >1.6 opt) coupled with its complex geological environment and relatively deep location dictated the choice of a very selective primary mining method, Mechanized Overhand Cut and Fill. In addition to geological challenges, mine design issues such as material handling, ground stability and requirements for yieldable ground support are also discussed in this paper.

Oct 1, 2001

By Douglas Rudenko

Have you ever had a neighbor complain about a blast one day, but says the next day’s blast was better, even though the Peak Particle Velocity (PPV) increased? How about neighbors that complain about a small trimming shot, but don’t complain about a big production shot? Have you ever reduced the pounds/delay and gotten more complaints ? Mine operators are often bewildered when trying to correlate blast design parameters to homeowner complaints. When complaints come, standard practice is to set up a seismograph in the neighbor’s yard to monitor the blast. Immediately after the blast, the neighbor usually reappears from the house wanting to know the seismograph reading. When told that the PPV was 0.1 in/set, well below damage levels, the homeowner explodes saying “Your machine is wrong”. Perhaps he is right. Understanding why people complain about blasting is not about PPV, it’s all about structural response. People could care less about how much the ground vibrates; they only care about how much their house vibrates. In this paper we will examine the primary factors that control structural response. Through the use of a large array of digital seismographs, the effects of two production blasts on a community surrounding a quarry are studied. The predicted structural response resulting from each blast is calculated at 175 seismograph locations. The predicted response is then correlated to previous research on human perceptibility to vibrations. The results of this analysis and correlation give a better understanding of what the residents actually feel in their homes. The detonations of two single-hole signature blasts are also recorded by the array of seismographs revealing the dynamic characteristics of the geology ‘surrounding the quarry. Once the influence of the geology was understood, blasts were configured to disrupt the natural rhythm of the site through the use of millisecond delays.

Jan 1, 2000

By D. Neely, D. Milne, L. R. Feldman

"Resin-anchored rebar is commonly used for rock support in mining. The rock properties and environment determine the average bond strength, allowing mine engineers to select the appropriate length and installation pattern for the support. In weak material such as potash, the average bond strength tends to be lower than for a typical hard-rock installation. Determining the failure mechanism by which the support fails in soft-rock applications could lead to improved bond strength and better calculated installed support capacity. This paper reports on research conducted at a potash mine in Saskatchewan and analyzes the failure mechanism of the support.RÉSUMÉ Dans les mines, les barres d’armature enduites de résine sont fréquemment utilisées pour soutenir le roc. L’environnement et les propriétés du roc déterminent la résistance moyenne d’adhésion, permettant ainsi aux ingénieurs miniers de choisir la longueur de barre appropriée et le diagramme d’installation du soutien. Dans des matériaux faibles, tels que la potasse, la résistance moyenne d’adhésion tend à être plus faible que pour une installation typique dans de la roche dure. La détermination du mécanisme de rupture selon lequel le soutien fait défaillance dans des roches tendres pourrait conduire à une meilleure force d’adhésion et à un meilleur calcul du soutien installé. Le présent article fait état de la recherche effectuée dans une mine de potasse en Saskatchewan et analyse le mécanisme de défaillance du soutien. ,"

Jan 1, 2016

The design, specification, and performance evaluation of the Communications and Location portions of a Coal Mine Rescue and Survival System are described. The work was performed as part of a nine month effort to develop a mine rescue and survival system using existing technology and state -of-the -art hardware as recommended by the National Academy of Engineering. Three basic subsystems were developed, one for survival, one for communications/location and one for rescue. This report and related equipment manuals describe only the Communications/ Location Subsystem which was designed, fabricated, and tested by the Westinghouse Georesearch Laboratory in Boulder, Colorado. Two basic technologies were used. Electromagnetic signals propagating through-the-earth provide voice downlink and coded beacon up-link communications. Seismic methods were developed to provide means for locating trapped miners. Seismic signalling also provides a backup means for communications. Parallel development programs for the electromagnetic and seismic portions of the system were conducted. The resulting hardware and software have been partially tested in coal mines and under simulated emergency conditions in order to evaluate system performance. The results of these tests are discussed. Further testing is recommended in order to establish quantitative performance limitations tinder a variety of environmental conditions and to develop methods for improving system performance.

Jan 1, 1971

By Xavier B. Starnes

"INTRODUCTION The Krausse Estate property was the site of the first lead silver mining in western Kentucky, which began with the sinking of the Andrew Jackson shaft in 1835 3/. The earliest miners considered fluorspar of no value and threw it upon the waste dump, but Crittenden County later became an important part of the western Kentucky and southern Illinois fluorspar district 4/, which has produced about 90 percent of the fluorspar mined in the United States. By 1945, approximately 35,000 tons of fluordpar ore had been produced from the Estate property.This property can be reached by traveling west from Marion on Highway 60 from 2.5 miles, than northward 3 miles. The road from the paved highway to the mines is very rough but not impassable even in bad weather. Ore is hauled 5 1/2 miles by truck to custom mills at Marion, a town of 2, 000 population, where the Illinois Central Railway was a freight station.Hurricane Creek runs through the eastern part of the property. The surface slopes steeply upward to west from the creek, and the topography is rough. The top of the hill is about 150 feet above the creek.The climate permits working throughout the year, but spring rains cause surface water to enter mine and water apparently drains southward along the fractured fault zones, so that when no water is being pumped at properties north of the Krausse Estate a heavy flow comes on the Krausse."

Sep 1, 1946

By John R. Craynon

Science and Sustainable Development Each of the ?pillars? of sustainable development are directly impacted by mining. We need science to understand exactly how mining contributes to each. Overview of presentation ? History of mining and sustainable development ? Role of stakeholders in measuring/accepting contributions of mining to SD ? Identified ?shortfalls? in understanding mining and SD ? Science needs

Aug 1, 2013

By D. Nag, J. Fernando

Hazelwood Power Mine is one of the largest open pit brown coal mines in Australia. The removal of overburden is the first step in coal winning operation. The primary aim of construction of overburden dump is to provide an effective stable working surface for stacker. The paper discusses site investigation techniques used to determine dump soil properties, stability analysis method using GALENA and GWEDGEM, results of stability analysis. The paper concludes with recommendation for a safe dumping strategy for level 2 stacker dumping.

Jan 1, 2003

By A. J. Monhemius

"The paper reviews the history of modern iron control processes in hydrometallurgy. Particular attention is paid to the processes developed in the 1960s by the electrolytic zinc industry for the removal of iron from zinc sulphate leach liquors - namely the Jarosite, Goethite and Hematite processes. Problems faced by the industry in the safe disposal of the iron residues produced by these processes are discussed. The lessons learnt over the past half century by the zinc industry are projected on to the current efforts to develop hydrometallurgical processes for the treatment of copper sulphide concentrates. It is argued that any attempt to create a “hydrometallurgical copper smelter” is doomed to ultimate failure, unless and until methods are developed that can recover iron from solution in a form that can be directly utilised by the steel or pigment industries.INTRODUCTIONYou suddenly realise that age is catching up with you and that technology is moving on apace when you are asked to talk about the history of a process or a technology that you’ve grown up with. Such was my reaction when, out of the blue, I received an email last year from the chairman of the CIM’s Historical Metallurgy Committee, asking me if I would give a talk on the early developments of iron control in hydrometallurgy. Once I’d got over the initial shock of realising that I had now become living history, I was of course flattered that the invitation was to give a talk at the prestigious IMPC, a conference series that has been going for as long as I have been in the business. That this particular IMPC was to include the 4th Symposium on Iron Control in Hydrometallurgy, made the invitation even more appealing and appropriate, because I was the co-chairman of the First Symposium on Iron Control, together with my old friend, John Dutrizac (known by many as Dr Jarosite), which was held 30 years ago in Toronto.first became involved with iron at the very start of my career in hydrometallurgy – the research topic for my Masters degree thesis at UBC, back in the mid 1960s, was “Reductive leaching of Goethite with SO2”. My thesis supervisor was the late Professor Ian Warren, who himself was a protégé of Professor Frank Forward, one of the founding fathers of modern hydrometallurgy. Little did I realise at that time, now 50 years ago, that the problem of iron and how to deal with it in hydrometallurgical processes would be a theme that followed me throughout much of my 40-year career in academia."

Jan 1, 2016

By Sterling J. Anderson

Through the use of nondestructive testing techniques, the Bureau of Mines is pursuing a goal of improving the efficiency of the rock excava-tion process. Toward this end, 44 laboratory tests were conducted to identify a practical method of monitoring fracture development in rock, as caused by an excavation tool. An acoustic emission CAE) transducer was used to monitor the test samples as they were loaded. The signal from this instrument was recorded in real time along with the radial and axial loads generated by the fracturing device. Through the review of these signals on a common-time base, it was possible to see the relationship between the developing fracture and the loading conditions. As a part of the posttesting investigations, samples that were pletely fractured were sawn and ground to expose the fractures. examination of these samples allowed approximations to be made incom-Visual of the total surface created. Surface area approximations were also made for the completely fractured samples. Quantitative analyses· of the AE signals were conducted for comparisons with the calculated surface areas.

Jan 1, 1987