Search Documents

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By A. G. Eccles

"INTRODUCTIONWestern Mines' copper-lead-zinc operations are located in Strathcona Provincial Park, near the geographic centre of Vancouver Island. This park includes Buttle Lake, which flows into the Campbell River water system. The latter provides domestic water for the Town of Campbell River, approximately fifty-eight miles from the mine site.Operation of the concentrator commenced in December 1966, at which time the tailings were discharged into a small tailings pond near the plant. On May 8, 1967 Permit No. 185 was granted to the company, allowing discharge of the tailings, through a submerged outfall, to the bottom of Buttle Lake.Needless to say, the concept of operating a mine within a park, and the discharge of tailings into Buttle Lake generated considerable controversy. However, this has all but been eliminated over the years by the proven effectiveness of Western Mines' pollution control program. In 1973 this program was further upgraded with the addition of an alkaline chlorination plant. Effluent treatment by this method became necessary as a result of process modifications, and has been effective in maintaining the levels of characteristics in the tailings within the ever increasing pollution control requirements imposed on the industry."

Jan 1, 1977

By D Craw, K A. Hunter

Deposits of the metalloids arsenic and antimony occur in quartz veins of mesothermal hydrothermalsystems in the South Island as arsenopyrite (AsFeS) and stibnite (Sb2S3). Arsenopyrite and stibnite occur in natural exposures in gold-mining areas, and additional arsenopyrite and stibnite have been exposed to the atmosphere by mining activity. At present the drinking water limits for dissolved As and Sb are 10 ppb and 3 ppb respectively. Sampling and analysis techniques are critical to determination of metalloid concentrations at these low levels. Endeavour Inlet in the Marlborough Sounds is an historic mining area (late 19th Century) with elevated As and Sb in waters emanating from mineralised rocks. Waters running out of abandoned adits have concentrations of As and/or Sb up to ppm levels. Natural waters have high Sb and low As, and the As levels increase markedly where anthropogenic activity has exposed rock. Changes in Sb/As ratio could potentially be used to quantify the anthropogenic component of metalloid mobility on mine sites on the 100-year time scale.

Jan 1, 2002

By Merwin H. Howes

Gnome shaft, situated about 24 miles southeast of Carlsbad, N. Mex., was designed and sunk by the U.S. Atomic Energy Commission for conducting a peace- time experimental nuclear explosion in the thick salt beds of the Permian Salado formation. Excavation was started July 1, 1960, and completed July 26, 1961. The 10-foot diameter shaft, lined with concrete through the rock section, was sunk 1,216 feet. A drift was driven approximately 1,140 feet on the 1,200- foot level terminating in a shot chamber. On completion of 100 feet of shaft, by means of a truck-mounted crane, facilities were installed for conventional sinking. About 709 feet of rock and 506 feet of salt were encountered in the shaft. Salt beds at this place are reported to be over 1,200 feet thick. The overlying rock section varies greatly in composition and thickness of beds and contains a 28-foot bed of water-bearing dolomite. The aquifer was sealed to facilitate shaft sinking and to prevent water-seepage damage in the salt section of the shaft. Sealing was accomplished by grout injection through holes drilled into the aquifer and by grouting behind the concrete liner.

Jan 1, 1963

By Merwin H. Howes

Gnome shaft, situated about 24 miles southeast of Carlsbad, N. Mex., was designed and sunk by the U.S. Atomic Energy Commission for conducting a peace-time experimental nuclear explosion in the thick salt beds of the Permian Salado formation. Excavation was started July 1, 1960, and completed July 26, 1961. The 10-foot diameter shaft, lined with concrete through the rock section, was sunk 1,216 feet. A drift was driven approximately 1,140 feet on the 1,200-foot level terminating in a shot chamber. On completion of 100 feet of shaft, by means of a truck-mounted crane, facilities were installed for conventional sinking. About 709 feet of rock and 506 feet of salt were encountered in the shaft. Salt beds at this place are reported to be over 1,200 feet thick. The overlying rock section varies greatly in composition and thickness of beds and contains a 28-foot bed of water-bearing dolomite. The aquifer was sealed to facilitate shaft sinking and to prevent water-seepage damage in the salt section of the shaft. Sealing was accomplished by grout injection through holes drilled into the aquifer and by grouting behind the concrete liner.

Jan 1, 1963

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite represents one of the main players in the stability of the drilling mud. Its particle size and particle size distribution affect the physical properties of the drilling mud especially the rheological properties. Therefore, a specific particle size distribution was recommended by American Petroleum Institute (API) for use in drilling mud. To clarify the effect of individual size and size distribution, in this study, the bentonite sample was classified into different size fractions. Each size fraction was tested separately in terms of controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness, and packing density. The effect of each size fraction on the rheological properties of the suspension was correlated to the behavior of the whole particle size distribution in the bentonite sample. The results indicate that the coarser the particles, the higher the rheological properties; in this case, the API mixture is the highest. The filtration loss and cake thickness for the API mixture are lower than that of the individual size fractions due to its wider size distribution due to the filling of voids between larger particles with smaller ones, which lead to bed compaction and consequently lower fluid loss and cake thickness.

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

In order to address the difficulty of accurate segmentation of froth images of different sizes, a method of froth image segmentation based on highlight correction and parameter adaptation is proposed. First, a machine vision system on a single-cell flotation machine is built to collect froth images. Homomorphic filtering is used to improve the uneven brightness and shadow of the images. Fuzzy c-means (FCM) clustering is then utilized to classify similar highlights that belong to the same froth. After Otsu threshold segmentation, a parameter-adaptive morphological operation is used to extract the marker points and edge bands and correct the froth edges in the original image. Finally, the modified image is filtered by morphological reconstruction, and the highlight mark is used as the local minimum point for watershed segmentation. Three sizes of froth images are segmented in comparative experiments. The results show that the proposed method is suitable for the segmentation of froth images of different sizes. The position of the extracted segmentation line is close to reality, with average over-segmentation and under-segmentation rates for froth images of 2.6% and 6.8%, respectively. The froth image segmentation performance is stronger than that of the other methods examined.

By Elmer Stewart, Richard May

"The Central Mukur deposit was discovered by the Semipalatinsk Geological Exploration Expedition (GEE) during detailed searches from 1977 to 1980. Andas Altyn Ltd., a Kazakhstanian gold mining company acquired the property and commenced mining in 1995. In 1998, Andas-Altyn Ltd. became a wholly owned subsidiary of Eurasia Gold Corporation.The Central Mukur gold project covers a linear series of parallel, discontinuous zones of near surface oxide gold mineralization that covers a distance of 7 kilometers and extends past the property boundaries. The oxide gold mineralization is a result of the regional oxidization of a primary sulfide gold mineralization emplaced in a series of shallow dipping thrust faults. Resources as calculated by the GEE are 3.45 mt at an average grade of 1.84 gmt Au in the C1 +C2 category and 7.52 mt at an average grade of 1.80 gmt Au in the P1 category. The Central Mukur Gold Heap Leach Mine consists of an open pit, heap leach pads, and an ion exchange resin gold recovery plant. Limited gold production (<2,500 ounces/year) has been achieved over the past three years leaching run of mine oxide gold mineralization. Gold recovery utiling cyanide to dissolve the Au and ionic resin technology to recover the Au for the leachate is approximately 60%. Loaded resin is shipped to a treatment plant at Almaty where the gold is stripped from the resin, refined and sold.This paper will describe the geology, mining, and processing of the Central Mukur ore. In addition, it will describe what it is like doing business in Kazakhstan and the transition from a Soviet style operation to a more western style operation.INTRODUCTIONThe Central Mukur Mine is owned and operated by Andas-Altyn Ltd. a Kazakhstanian gold mining company located in northeast Kazakhstan. Andas-Altyn is a wholly owned subsidiary of Eurasia Gold Corp., a Canadian public company listed on the Alberta Stock Exchange. The Central Mukur mine consists of a small open pit, and a heap leach operation that utilizes ion exchange resin to recover gold from pregnant solutions. In addition to the Central Mukur mine, Eurasia also owns the Myaly heap leach gold project which is also operated by Andas- Altyn Ltd."

Jan 1, 1999

From a vast army of workers to gargantuan machines to immense volumes of material being moved, almost everything about the Port of Miami Tunnel (POMT) project points to tunneling on a massive scale. Almost.The star of this underground and underwater show is a Herrenknecht tunnel boring machine (TBM,) nicknamed ?Harriet? by a local Girl Scout troop. With her 12.9-m- (42.3-ft-) diameter cutting head and a total length of 139 m (457 ft), Harriet is boring through thousands of cubic meters of clay, dirt and sand, which is often mixed with coral and other materials, to create two 1,280-m (4,200-ft) traf?c tunnels connecting Watson Island and the Port of Miami (Dodge Island) beneath Biscayne Bay, FL. But in the midst of all of the oversized equipment and machines, a strong contender for the best supporting nod goes to a relatively tiny machine: the Brokk 400. Bouygues Civil Works Florida crews are using the compact, remote-controlled and electric-powered machine to excavate five cross passages between the twin traffic tunnels. The pas-sages will be essential to the safety of people who drive their vehicles under the bay every day.

Sep 1, 2013

An integrated palynological and sedimentological investigation of four wells from the eastern margin of the Gippsland Basin has resulted in a scheme for classification of palynofacies in this area. Thirteen different palynofacies assemblages are recognised and assigned to particular environments based on the enclosing sediments, which range from alluvial, through coastal barrier to continental shelf environments. Close correlation is observed between the interpreted energy regime of the palynofacies assemblage, and that of the enclosing sediments. Assemblages characterised as reworking surfaces can be correlated with unconformity producing events (ie tectonic activity associated with the opening of the Tasman Sea), and some of the minor eustatic sea level Changes.

Jan 1, 1992

By M. J. Gavin

Within the past three years numerous inquiries for information on oil shale have been received by the Bureau of Manes. These inquiries have been increasing to such an extent that it has seemed advisable to issue a short paper prior to the publication of a bulletin on the subject, giving a, general discussion of the subject and a comprehensive list of references, so that those interested in the details of obtaining oil from shale can find additional information without much difficulty. Some of those who desire information are interested only in a general discussion of the subject, or are not in a position to refer to books and&apos; articles describing the industry. The material for this paper is largely derived from published information on oil shale. Much of the information is obtained-from the books and articles mentioned in the list of references, and has been compiled with the intent of furnishing information to those not interested in all the details.

Jan 1, 1921

By W. F. Dietrich

1. On St. Thomas and St. Croix, and possibly also on St. John, low-quality red-burning clays probably can be developed to provide the major part of the raw materials for structural clay products and earthenware pottery. 2. The potential sales volume for structural clay products is too small to sustain a plant in the Virgin Islands to manufacture such products in competition with Puerto Rico; however, handmade patio tile might be produced successfully. 3. The market for pottery utility wares in the Virgin Islands is too small to justify a plant devoted solely to the production of such wares; but it may be feasible to evolve a diversified community activity to make jugs, pots, casseroles, bowls, charcoal burners, patio tile, and other items.

Jan 1, 1955

By F. S. Wartman

This paper gives an account of the production of ductile-grade titanium powder in 100-pound batches by reduction of purified titanic Chloride with magnesium, grinding, leaching, and magnetic-separation of the reaction product. Apparatus, technique, and methods of controlling product quality are described and some data on operating costs are given.

Jan 1, 1949

By W. D. Maier, H. V. Eales

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. A lithological and geochemical study revealed significant lateral variation of the interval over 170 km of strike, from about 30 m at the Union Section to 220 m near Brits. The cumulates also become more evolved and leucocratic with distance from the Union Section both towards the NE (Amandelbult) and SE (Impala, Rustenburg and Brits). It is inferred that the persistent heat flux from a putative major feeder zone near the Union Section impaired deposition of felsic cumulates in the vicinity, delaying crystallisation of successive phases in parts of the chamber near the feeder. New influxes were therefore deposited on a footwall of varying thickness and lithology in response to different degrees of crystallisation and accumulation along strike. The development of cyclic units of chromitite, harzburgite, pyroxenite, norite and anorthosite was interrupted at different stages in different parts of the chamber

Apr 1, 1994

By Alfred Bodenlos

El presente artículo describe la historia geológica pre-cretácica de la Cordillera Negra. En algunos intervalos predominaron los pantanos que dieron lugar a la formación de carbones. Luego, en el Valanginiano superior, la región estuvo sumergida, depositándose calizas delgadas. Los tufos que yacen sobre la secuencia de elásticos indican que hubo actividad volcánica a fines de este intervalo. Parte apreciable de los depósitos marinos del Cretácico medio está formado por calizas bituminosas obscuras.

Jul 1, 1957

By Stephen M. Jasinski

The development and industry adaptation of advanced technologies have led to many important uses for bismuth and its compounds. Bismuth-base alloys are essential for manufacturing jet engine turbine blades, lenses, and various safety devices, such as fire-protection sprinklers. The addition of bismuth to iron, steel, and aluminum imparts properties to these metals that makes them useful in diversified applications. Bismuth is also used widely in medicine, pigments, and electronics. The United States relies heavily upon imports from South America and Europe to meet its demand for bismuth, which is recovered chiefly as a byproduct of lead processing.

Jan 1, 1992

By J. P. Gous, J. J. Sutherland

"Transalloys is a silicomanganese (SiMn) producer located in South Africa, and uses only local manganese ores to produce SiMn alloy. The plant operates five open submerged arc furnaces (SAFs) with an annual capacity of 180 000 t of saleable SiMn.Maintaining tap-holes is critical for effective furnace operation, allowing proper drainage of the furnace with minimal operator interference. Using a claygun and drill arrangement installed at each furnace, tapping occurs every four hours. Tap-holes are maintained through mickey replacement and brick repairs. Three furnaces have SiC tap-holes and two have graphite tap-holes.This paper gives a review of SAF operation, furnace and tap-hole design, daily tapping operation, and maintenance practices for repairing tap-holes.IntroductionDefining tap-hole life cycle, Steenkamp et al., (2016) highlighted four main steps: installation during furnace relines, day-to-day operations, tap-hole maintenance, and tap-hole repair. The authors argued that the design of the tap-hole area should allow for all four stages in the tap-hole life-cycle. Design principles for each stage were presented using silicomanganese (SiMn) production as a case study. Here we present a further analysis of the case study by providing practical examples of how the tap-hole life-cycle is managed at Transalloys during the design, operation, and maintenance of submerged arc furnaces (SAFs) applied in the production of SiMn.BackgroundTransalloys is the largest producer of SiMn in Africa. Its smelter complex is based outside the town of eMalahleni, in the Mpumalanga Province of South Africa. Transalloys was commissioned in the mid- 1960s as a high- and low-carbon ferrochromium plant based on the Perrin process. In 1967 the plant was converted to SiMn production because of constraints in the ferrochrome market (Basson, Curr, and Gericke, 2007; Bezemer, 1995). Today, the installed production capacity is 180 000 t of SiMn annually. Plant operations consists of five SAFs (see ratings in Table I), operating 24 hours a day, 365 days a year (including maintenance), involving 280 permanent employees, with up to 120 contract employees on site at any given time."

Jun 1, 2019

By Mustapha A. Raji, Alafara A. Baba, Christianah O. Adeyemi, Aishat Y. Abdulkareem, Rafiu B. Bale, Malay K. Ghosh

The increasing demand for pure aluminum and aluminum compounds of industrial quality from kaolinite ore cannot be overemphasized. Nigeria is one of the African countries endowed with abundant solid mineral resources that have not been sufficiently exploited to assist its indigenous industries. A wide array of applications of pure aluminum and its compounds are available, such as paper filling, refractories, adsorbent, catalysis, and paint additives. In this study, the upgrading of a Nigerian biotite-rich kaolinite ore by a hydrometallurgical route was investigated in oxalic acid media. During leaching studies, the effects of parameters including reaction temperature, lixiviant concentration and particle size on the extent of ore dissolution were examined. At optimal conditions (1.0 mol/L C2H2O4, 75 °C), 92.0% of the initial 10 g/L ore was reacted within 120 min. The dissolution curves from the shrinking core model were analyzed and found to conform to the assumption of surface diffusion reaction, and the calculated activation energy of 33.2 kJ/mol supported the proposed model. The unreacted product (~8.0%) analyzed by XRD was found to contain siliceous impurities and could serve as a valuable by-product for certain industries.

By Mustapha A. Raji, Alafara A. Baba, Christianah O. Adeyemi, Aishat Y. Abdulkareem, Rafiu B. Bale, Malay K. Ghosh

The increasing demand for pure aluminum and aluminum compounds of industrial quality from kaolinite ore cannot be overemphasized. Nigeria is one of the African countries endowed with abundant solid mineral resources that have not been sufficiently exploited to assist its indigenous industries. A wide array of applications of pure aluminum and its compounds are available, such as paper filling, refractories, adsorbent, catalysis, and paint additives. In this study, the upgrading of a Nigerian biotite-rich kaolinite ore by a hydrometallurgical route was investigated in oxalic acid media. During leaching studies, the effects of parameters including reaction temperature, lixiviant concentration and particle size on the extent of ore dissolution were examined. At optimal conditions (1.0 mol/L C2H2O4, 75 °C), 92.0% of the initial 10 g/L ore was reacted within 120 min. The dissolution curves from the shrinking core model were analyzed and found to conform to the assumption of surface diffusion reaction, and the calculated activation energy of 33.2 kJ/mol supported the proposed model. The unreacted product (~8.0%) analyzed by XRD was found to contain siliceous impurities and could serve as a valuable by-product for certain industries.

By Eric Low

Raising capital by issuing debt or equity is necessary in almost every corporation. In the field of corporate finance, the raising of capital is a heavily-studied topic. However, some of what is studied on this topic in corporate finance is not applicable in the mining industry. There are also many financing options that were created for the mining industry such as flow-through shares, prepaid forwards, and royalty sales. The cyclical nature of the industry makes the risk-return profile of financings more difficult to estimate than in other industries. Additionally, the methods used to assess firm value are different than other industries, as the values of orebodies are not included on balance sheets. For precious metals companies, which are a hedge against most other securities, there are additional complications with determining investor expectations and cost of equity. This thesis puts forth a decision-making framework to explain mine financing choices from the perspective of mining companies. The approach is threefold. First, all of the major equity and debt financing instruments available to mining companies are presented and analyzed. Each financing method is assessed on a wide range of criteria. Next, these concepts are applied in case studies of four companies: BHP Billiton, Barrick Gold, Teck Resources, and Noront Resources. For each company, the overall choice of financing methods is shown and analyzed. The effect of financing choices on the weighted average cost of capital (WACC) is calculated. The final section deals with case studies of individual mine finance decisions during the past two years.

May 1, 2011