Search Documents

By André Pomerleau, Michel Grégoire, René del Villar

"The operation of industrial flotation columns requires the control of at least two variables, the interface position and the bias rate, by manipulation of some appropriate operating variables. Problems arise due to the reliability of existing methods of measuring the bias (i.e bias = tailings water - feed water), a situation which has often forced the industry to disregard this control loop. Moreover, when using such a measuring approach, the identification of the process dynamics is impossible. A second problem arises from the possible interaction between both control loops that might call for the use of a more complex multivariable control strategy.Recent work done at Lava1 University has demonstrated the feasibility of an independent sensor for bias, which models the relation between the conductivity profile across the interface and the bias value using a neural network algorithm. A 250 cm height, 5.25 cm diameter Plexiglas laboratory column was equipped with a series of conductivity electrodes in its uppermost part (across the interface) to measure both interface position and bias rate. Using such equipment, the flotation column dynamics were identified. The results thus obtained permitted the design and implementation of a distributed PI control strategy, where bias was associated to wash water rate and froth depth to tails rate. Both PI controllers were tuned using a frequency-response tuning method. Results of both identification and process control are presented and discussed.INTRODUCTIONFlotation columns are used for the separation of valuable minerals from a carrier gangue. Typically, this device is a tall (9 to 14 m height) cylinder (1 to 3 m in diameter) although other cross sectional shapes are also used. Finely ground ore is fed as a pulp at about 2 m from the top of the column, and pressurized air is introduced through a sparger at the bottom. If the pulp has been properly conditioned with adequate chemical reagents (collectors and modifiers), the valuable mineral particles falling by gravity will attach themselves to the rising air bubbles, and the air-particle aggregates will rise to the top of the column where they overflow as a stream called the concentrate. The gangue particles,, that do not attach to the air bubbles, fall down the column being withdrawn at its bottom in a stream called the tails.A particular characteristic of flotation columns is the addition of a fine spray of water at the top. As the water flows down through the froth zone, it washes out the entrained gangue particles from the mineralized bubbles, thus improving the quality of the concentrate recovered at the top. As a result of its cleaning action, this water stream is called the wash water and the upper zone, the cleaning zone. In order to ensure a downward flow of wash water, a proper water balance must be kept in the froth zone, otherwise the water added at the top might shortcircuit to the concentrate without performing any cleaning action. This net downward flow of water inside the froth zone is called the bias and represents an important operating variable of a flotation column."

Jan 1, 1999

By Ishwinder Grewal, Michael Fullam

Many factors affect the overall performance of a gravity circuit beyond that of the primary gravity recovery device. It is critical to examine the gravity circuit in its entirety in order to determine the dominant operating variables that affect overall performance. Knelson has developed a mathematical model which has been used to assist in the design of gravity circuits, and in particular, in making accurate predictions of plant scale gravity recovery. More recently, inclusion of recovery by particle size class and additional data from various mine sites and research studies has made the model more robust. The model is now able to predict GRG (gravity-recoverable-gold) recoveries using various devices such as centrifugal concentrators, shaking tables, jigs and flash-flotation within the grinding circuit. The benefits derived by these recent advancements in modeling capability are two-fold; the first is as a tool to assist in circuit design and correct equipment selection and the second is as an analytical tool to help to evaluate and enhance the performance of existing gravity circuits.

Jan 1, 2006

By Peter Klaver

Deep tunnels have been used for decades for the temporary storage of large volumes of urban runoff, both storm water and combined sewer overflow (CSO). Tunnels are attractive because they reduce surface disruption and do double duty as storage and conveyance systems, collecting overflows from multiple locations and transporting them for treatment to various facilities. Like any hydraulic system, however, there are dynamic effects that must be fully understood during the design phase so that the final constructed product does not have unintended negative consequences. Preliminary sizing of storage tunnels is typically based on the total volume required. For example, if studies have determined that a volume of 56.8 ML (15 million gal) will provide the intended level of control, then that figure can be used, along with a preliminary idea of the desired tunnel length, to compute the required diameter. Of course, filling a long tube with water from various points along the way is not at all the same as pouring water into a bucket, and these dynamic effects require additional attention from design engineers. The rapid filling of storage tunnels can lead to the formation of bores, which are essentially moving walls of water. An open channel bore can build in height until it reaches the crown of the tunnel, at which point it becomes a pipe-filling bore. Figure 1 depicts both kinds of bores moving upwards in a rapidly filling tunnel. Bores can strike the ends of tun-nels with tremendous force, driving water and entrained air upwards into dropshafts and creating strong pressure surges in portions of the tunnel that are already filled. If the hydraulic surges are high enough to reach grade, they can cause overflows and/or damage structures at the surface. Trapped air pockets can occur through several phenomena, including the reflection of bores off dropshaft structures and the occurrence of ?premature pressurization.? The latter refers to the situation where the inflow to a tunnel is increasing more rapidly than the tunnel can convey it, such that the pipe becomes surcharged at an upstream point while points downstream are still flowing as an open channel. These air pockets are a great nuisance as they migrate toward points in the tunnel where they can rise to the surface, which are often shafts that are already filled with water (Fig. 2). The ?geyersing? that results can be hazardous and costly.

Jan 3, 2010

By C. McAllister, D. Preece, J. Berendzen

The Multiple Blasthole Fragmentation (MBF) model was developed recently and has been reported in previous papers. The MBF model accepts inputs from the blast design, such as: location and orientation of each blast hole, stemming length, blast hole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect on fragmentation of delay timing with its associated scatter for each blast hole. MBF has a statistical modeling capability for geological random variation of the attenuation of particle velocities. Also simulated is wave reinforcement due to the interaction of simultaneously arriving waves or diminishing cooperative contribution from long delay intervals between charges.

Jan 1, 2016

By M. J. McLeod, D. R. Lux, R. P. Taylor

"The Mount Douglas Granite constitutes the eastern part of the Saint George Batholith and contains the youngest, most differentiated phases of the batholith. It also contains extensive endogranitic, low-grade. Sn- W-Mo-bearing sheeted vein systems. Early phases of the Mount Douglas Granite are coarse- to medium-grained, seriate granites that represent the slowly cooled carapace of the intrusion. Late phases are medium- to fine-grained, equigranular and porphyritic granites that were accompanied by repeated and widespread fracturing of the carapace and injection of mineralizing fluids. These granites represent a highly differentiated suite with ""A "" type affinities developed in a ""within plate"" transitional to ""syn-collision"" tectonic setting. 4oAr/ 39Ar dates for biotites from the various phases indicate emplacement circa 367 Ma.The linear distribution of some phases in the Mount Douglas Granite and the systematic orientations of sheeted veins along tensional fractures indicate structural control on granite emplacement and vein distribution. This type of relatively passive endogranitic mineralization is unique in the granites of southern New Brunswick and contrasts markedly with highly fluidized systems operative elsewhere in the area. IntroductionInvestigation of Sn-W-Mo occurrences in New Brunswick has shown that most of this mineralization is associated with late, highly differentiated phases of post-orogenic (Acadian) granitoid magmatism that occurred during Devonian and Early Carboniferous time (Ruitenberg and Fyffe, 1982; Taylor et al., 1988). The polymetallic Mount Pleasant Sn-W-Mo deposit (Ruitenberg, 1967, 1972; Kooiman et al., 1986)and the Burnt Hill W deposit are two orebodies of this type in New Brunswick. Numerous smaller deposits associated with these granitoid rocks in southwestern New Brunswick have been documented in previous investigations (Ruitenberg, 1967, 1968; Ruitenberg and Fyffe, 1982; Taylor et al., 1985; Lentz, 1985)."

Jan 1, 1988

By A. W. Khair

This paper presents an analysis of fracture depth and intensity due to subsidence over the longwall panel. Sonic reflection techniques were utilized to determine fracture depth, and a variation of p-wave velocity was used as an indication of the fracture intensity. Instrumentation has been tested for consistency and accuracy first in the laboratory using small scale models, then applied in the field in two mine sites with different mining geometry and geologic conditions. A new sonic viewer was utilized for sonic velocity measurements. Regular hammering method was on acoustic source. The results were concurrent with monitored horizontal strain profiles and measured open fractures over the longwall panels.

Jan 1, 1989

By R. F. Zaffarano

Intergrated energy balances and energy flows were constructed and quantified for State, regional, and national levels from four separate supply and demand commodity balances for coal, dry natural gas, petroleum and natural gas liquids, and utility electricity. These commodity balances were integrated by source and sectors through conversion and aggregation of their components to energy equivalents expressed in British thermal units (Btu). A summarization of the total gross energy components of supply and demand for commercial energy derived from direct fuels, hydropower and nuclear power, based on individual States and regions, is tabulated for 1960 and 1965. Pertinent computerization details and more than 500 individual State and regional printout tables, in both original commodity units and Btu's, are shown. Using these data, energy flows between States and regions were calculated to identify surplus and deficit energy areas. Report emphasis is on the conceptual aspects of integrated energy balances, rather than on the development of missing State energy data.

Jan 1, 1969

By E. Marcoux, F. Lotfi, A. Belkabir, L. Maacha, A. C. Brown, S. Brunet

"Koudiat Aïcha is a small Zn-Pb-Cu deposit, enclosed in the Visean Sarhlef volcano-sedimentary series of the Moroccan Hercynian Jebilet massif. Base metal mineralization is located between a basal unit consisting of black argillite with arenite intercalations, and an upper unit composed of black argillite with locally fossiliferous calcareous units towards the top. Paraconcordant gabbro sills are present in both the upper and basal units, and the enclosing strata. Three successive phases of deformation linked to regional deformation overprint the volcano-sedimentary rocks and gabbros, as well as the sulfide mineralization.The mineral deposit includes several lenses of massive to semimassive pyrrhotite, 1 to 20 m thick, with a large halo of disseminated sulfide veinlets and sulfide nodules within a zone of intense chlorite alteration in the footwall. The ore mineralogy consists of massive to semimassive pyrrhotite with lesser amounts of sphalerite, chalcopyrite, arsenopyrite, galena, pyrite, and stannite.Lead isotope results (206Pb/204Pb averaging 18.27) suggest that the metals of the Koudiat Aïcha deposit are derived from the volcano-sedimentary host rocks. Sulfur isotopes also indicate a volcano-sedimentary origin, with bacterial reduction of sulfate (d34SCDT = -7.5‰ to -10.5‰). The conditions for sulfide meta-morphic equilibration range from 250° to 330°C (sphalerite and chlorite geothermometers). The gabbroic sills could have been a local heat source for hydrothermal circulation. Based on these geological and mineralogical features, a Besshi-type model seems appropriate for the genesis of the Koudiat Aïcha mineralization.Koudiat Aïcha est un petit dépôt de Zn-Pb-Cu, encaissé dans la série volcano-sédimentaire Viséenne de Sarhlef dans le massif Hercynien de Jebilet au Maroc. La minéralisation en métaux usuels se situe entre une unité basale d’argilite noire interlitée d’arénite et une unité supérieure composée d’argilite noire comprenant localement des calcaires fossilifères près de son sommet. Des sills de gabbro paraconcordants sont présent à la fois dans les unités basale et supérieure, ainsi que dans les strates environnantes. Trois phases de déformation successives associées a la déformation régionale superposent leurs effets sur les roches volcano-sédimentaires, les gabbros, ainsi que la minéralisation sulfurée. Ce gîte comprend plusieurs lentilles de pyrrhotite massive a semimassive de 1 a 20 m d’épaisseur au sein d’un large halo de veinules de sulfures disséminés et en nodules au sein d’une zone intensément chloritisée dans le mur du gisement. Le minerai consiste en pyrrhotite massive à semimassive avec des quantités subordonnées de sphalérite, de chalcopyrite, d’arsénopyrite, de galène, de pyrite, et de stannite. Les résultats de l’analyse des isotopes du plomb (206Pb/204Pb moyen de 18.27) suggèrent que les métaux du gîte Koudiat Aïcha proviennent des roches volcano-sédimentaires encaissantes. Les isotopes du souf¬fre indiquent eux-aussi une origine volcano-sédimentaire, impliquant la réduction bactérienne des sulfates (d34SCDT = -7.5‰ et -10.5‰). L’équilibration métamorphique des sulfures s’est produite entre 250° et 330°C (géothermomètres à sphalérite et chlorite). Les sills de gabbro pourraient avoir été la source de chaleur locale responsable de la circulation hydrothermale. Sur la base de ces caractéristiques géologiques et minéralogiques, il semble approprié d’invoquer un modèle de type pour Besshi pour expliquer la genèse de la minéralisation de Koudiat Aïcha."

Jan 1, 2008

By S. T. Reese

STATISTICS of injuries in the quarrying and related industries in the United States first became available when the Bureau of Mines collected reports from the operating companies for the calendar year 1911. Since then reports have been collected annually. The present bulletin, covering the calendar year 1952, is the 33d publication containing statistical data on injuries at quarries and related plants, and it is the first to be published since 1944. The last publication was Bulletin 458, Quarry Accidents in the United States during the Calendar Year 1942. The unpublished statistics for 1942-51 may be found in the Appendix of this bulletin. The Bureau of Mines is authorized to collect data on injuries at quarries, but there is no Federal law that compels operators to supply such data, and the reports received from operators are voluntary responses to the Bureau's requests for information. Although the figures presented herein may not be complete for the entire industry, every effort has been exerted to make them so, and the figures given are believed to be thoroughly representative of the hazards to which quarry workers are exposed. Moreover, the figures are com¬parable as between States -which is significant in view of the lack of uniformity among the States as regards classes of plants covered by State laws, classes of injuries covered by State reports, and other factors that tend to make it impracticable or impossible to compare the injury experience of one State with that of another or to comprehend the relative importance of the various causes of injuries in the industry as a whole.

Jan 1, 1955

By Armstrong M

The Coal Mining Engineering Branch of the New South Wales (NSW) Department of Mineral Resources, in its continuing effort to improve coal recovery from underground coal mining operations, has undertaken a study of the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces. The strata movement was monitored by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were connected to the suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors started subsiding as soon as the face retreated past the borehole and continued to subside until the subsidence levelled off when the face retreated 900 m past the borehole. The zone of major caving and bed separation extended to roughly 10 to 13 times the extracted seam thickness and high tensile strains developed inthis zone. The bulking factor of broken strata was less than 1.14 which indicated that the roof layers collapsed in big blocks. The goaf compaction was almost complete when the face retreat was 200 m. Low tensile strains prevailed in the strata overlying the zone of caving and bed separation.

Jan 1, 1986

By John C. Nigro

This Bureau of Mines report summarizes the performance characteristics of a 30-day around-the-clock gasification-pelletizing test conducted in October and November of 1980 with North Dakota Indianhead lignite. Gasification was conducted in a commercial-size, 6.5-it-diam, Single-stage, fixed-bed, atmospheric pressure producer with a rated capacity of about 30 million Btu/hr. Iron oxide pellets made from a commercial hematite concentrate were fired with the low-Btu gas in a 2.8-ft-diam by 35-ft-long pilot plant rotary kiln at a rate of 900 lb of pellets per hour. Gasifier operations at fuel feed rates up to 3 tons of lignite per hour and hematite pellet induration with raw 160-Btu/std ft3 lignite gas are described.

Jan 1, 1982

By A. L. Garassino

Dans cet article on parle sortout de l'approche de calcule pour les pieux charges horizontalement avec particuliere reference aux curbes p-y et è une solution semi-empirique qui prende en consideration les variations typiques du module du sol avec la deformation obtenue par les données expérimentales. 1. INTRODUCTION The analysis of the piles under lateral loads depends very strictly from the pile stiffness and geometry, from the soil type and from the strain field. Different approaches were adopted in solving the problem. Some Authors developed methods for estimating the ultimate lateral resistance of piles and pile groups by conventional static approaches, as the Brom's widely known (1964) or by the plane strain solution developed by Davis (1961) or by empirical engineering con­siderations l

Jan 1, 1994

By K D. Wilkes

The WEMCO Heavy Media Drum Separator was first introduced by WEMCO in California in the 1940`s, initially from their base in San Francisco and later when the company moved to Sacramento. The WEMCO Company became a part of EIMCO Process Equipment in 1985, and in 2002 EIMCO became a part of the GL&V Group when Dorr-Oliver EIMCO was created. Throughout this period of time the WEMCO Drum has been installed on a variety of different applications and is now operating at the heart of many of the world?s largest Minerals and Coal Processing Plants, as well as being used by many smaller producers and metal re-cycling operations. This paper looks at the practical aspects of using WEMCO Drums in a representative range of processing applications.

Jan 1, 2006

By R M. Briggs

Kapowai Caldera Complex (KCC), located 10 km west of Tairua (eastern Coromandel Peninsula), is a late Miocene composite collapse caldera, formed during eruption of several small and large volume andesitic rhyolitic ignimbrites. Numerous epithermal Au-Ag mineral deposits and associated alteration zones at the KCC are related to caldera (rhyolite lava domes, intracaldera faults) or regional structures (faults). The main epithermal deposit exposed in the central KCC is associated with an E-W striking structural boundary fault that cuts the Welcome Jack rhyolite dome. Propylitic (calcite - chlorite) and sericitic (quartz - sericite) alteration haloes surround this deposit. Sporadic zones of sericitic alteration are also exposed within and on the margins of the Bulls Run rhyolite dome complex. Epithermal systems post-dated emplacement of these rhyolite domes, but were controlled by them. Propylitic alteration of ignimbrite in the floor of the Kapowai and Kauaeranga valleys is related to the major NE-trending Kapowai Fault which extends SW to south of Thames. Alteration along this fault pre-dates alteration associated with the rhyolite lava domes. Numerous sericitic and propylitic altered welded ignimbrite, rhyolite and andesite lava lithic fragments have been sampled from intracaldera ignimbrites, and although no direct source is known, they infer the presence of buried epithermal systems. Repeated epithermal activity at the KCC is inferred by the exposed epithermal deposits/alteration zones and the older buried geothermal systems. Silicic caldera volcanoes are considered to be critical volcanic environments for epithermal Au-Ag mineralisation in Coromandel, but are highly variable and need detailed stratigraphic, structural, petrologic, and geophysical studies to characterise them.

Jan 1, 1999

By J. Haynes

Coal mines in the eastern US often use sloped shafts as production beltways for ore removal, as means of access for supplies, and for ventilation. These structures are usually completed with the help of a contractor. In late 2011, Frontier-Kemper Constructors was engaged to build a slope for a coal mine in southern Indiana. Although the site was located in familiar Illinois basin formations, the geology proved to be very difficult. This paper describes some of the challenges faced during excavation of this slope and the methods used to overcome them, including changing the method from conventional drill and blast to cutting with a continuous miner.

Feb 27, 2013

By Martin B. Hudson, Daniel Brescia, Zhangwei Ning

Due to the complexity and sensitivity of surrounding environments, instrumentation and monitoring (I&M) is critical for many urban deep excavations. The objects to be monitored include shoring bulkheads, retained embankments, adjacent buildings and roads as well as underground utilities. However, there are also plenty of constraints on the implementation of I&M such as: congested site space, difficult access to instruments, coordination among multiple contractors, and installation permits for private or public properties. Because of these constraints, sometimes the implementation of the initially planned I&M is delayed, its scope is reduced, and/or the continuity of monitoring is interrupted. For these reasons, it is important to implement the I&M with robust and redundant capabilities while providing minimal interference to the project construction and schedule. This paper describes state-of-the-art I&M technologies including automatic motorized total station (AMTS) with camera and automatic leveling device, reflectorless AMTS and IoT- based wireless sensors based on a case study of an on-going deep excavation project. INTRODUCTION In urban environments, deep excavations requiring the construction of temporary shoring bulkheads are becoming increasingly common, with the associated need to provide protection of the surrounding built environment during construction. Protection of the surrounding environment requires planning, engineering, construction, monitoring, and excessive shoring movement mitigation. The I&M is a vital component of the deep shoring implementation. In public projects, geotechnical I&M is often placed within the general contractor’s scope, whereas the majority of deep excavations are privately undertaken. For those private developments, sometimes the developer contracts the geotechnical I&M directly with the project geotechnical engineer or by a geotechnical I&M specialist hired by the project geotechnical engineer. In either the public project or private development case, the effective deployment of the I&M system relies heavily on coordination and collaboration with the project contractor.

Jan 1, 2018

By Lyne Côté, Jose Adante

"The Caribou underground mine, 50 km west of Bathurst, the Restigouche open-pit mine, another 30 km west and the concentrator located at the Caribou mine site resumed operations in July 2007 after a nine year shutdown. The Caribou operations achieved commercial production on Jan 1. By June, 2008, all metallurgical targets had been achieved or surpassed with the production of lead and zinc concentrates assaying approximately 50% Zn and 45% Pb respectively with recoveries exceeding 80% for Zn and 70% for Pb.The deposit features very fine-grained massive sulphide mineralization, which in the past has proven difficult to process. ISA Mill Ultra Fine Grinding Technology in combination with conventional flotation technology is used to process these complex oresSeveral modifications arising from experience gained from past operations, an extensive research project at Lakefield Research and post startup flow sheet and reagent alterations have been employed to achieve this break through performanceThis paper describes the design, start up and optimization of the Caribou operations including the many challenges faced including the flotation of mineral particles with K80s ranging from 35µm to 8µm.HISTORICAL BACKGROUNDThe Caribou massive sulphide deposit was discovered by Anaconda geologist Cam Cheriton in 1959. Anaconda initiated an extensive underground exploration and discovered a super gene copper blanket which was developed into a small open-pit mine-mill operation that ran from 1970 until the depletion of the copper ore in 1974. East West Minerals, an Australian public company, purchased the mine in 1986 and operated for only seven months producing a single bulk lead-zinc concentrate. In 1995, Breakwater acquired the Restigouche Open pit and Caribou underground deposits. Breakwater began milling operations in July 1997 but Caribou Mine failed to commercialize production, and the company decided to shut it down in August 1998, because of declining metal prices. The mill was plagued by mechanical and design problems, but deficiencies in metal recoveries prevented the operation from reaching desired levels."

Jan 1, 2009

By John Ward Smith

Aragonite, co-occurring with calcite and dolomite as matrix minerals, has been discovered in Mahogany zone oil shales of Colorado's Eocene Green River Formation, posing puzzles on the geochemical patterns of their separate origins, reasons for their simultaneous existence, and their interrelation. The presence of aragonite is demonstrated by X-ray diffraction. Amounts of aragonite and dolomite are significantly and inversely related, but the calcite quantity is essentially independent of either aragonite or dolomite quantity. A geochemical pattern outlining the deposition conditions that created the Green River Formation oil shale is postulated from characteristics of the oil shale. The development of the three separate carbonates--aragonite, calcite, and dolomite--the inverse relationship between aragonite and dolomite, and the independence of amounts of calcite and the other two carbonates are shown to be natural consequences of this oil-shale genesis pattern.

Jan 1, 1973

The Southwest Pacific is a region of active volcanism and geothermal systems. Only in New Zealand have the geothermal systems been exploited for electricity generation and industrial processing. At present, approximately 280 MWe of geothermal electricity is generated in New Zealand. A considerable amount of further exploration work is required before the total geothermal potential of the region can be assessed and before the significance of these resources can be judged against other local energy sources.

Jan 1, 1990

By W. J. Wenger

Oil fields in the Powder River Basin of Wyoming have produced 731 million barrels of petroleum through 1959. Production in 1959 was 32 million barrels, the highest production since 1924. The record production was in 1923, when the Basin produced 38 million barrels of oil and the Salt Creek field, then at its peak, produced 35 million barrels. In this report, the characteristics of crude oils found in the Basin are used as a basis for determining the best re-fining uses for the oils and for predicting the characteristics of oils that may be discovered in the Basin in the future. Analyses of 108 oils sampled over a period of 30 years are presented Crude oils of two major types are produced from the Powder River Basin. One has a low sulfur content and occurs in younger formations, and the other has a high sulfur content and occurs in older formations. The oils with low sulfur contents are generally light colored and waxy, and may be either paraffinic or naphthenic. The oils with high sulfur contents are usually dark colored and asphaltic; only their low boiling fractions are paraffinic. Alteration appears to account for the anomalous properties of some oils found at shallow depths. Shapes and slopes of correlation index curves classify the oils into the same two groups as their sulfur contents, with gently sloping curves representing the low-sulfur oils and steep curves representing high-sulfur, asphaltic oils,

Jan 1, 1961