Search Documents

By J. E. Johnson

IT is the purpose of the present paper, while not excluding chemical considerations, to deal more extensively with some of the physical and mechanical aspects of the blast-furnace process, and to point out its dependence in these respects on well-known laws. The quantity and cost of ore and flux required to make a ton of iron being determined by circumstances over which the furnace-man, under given conditions as to quality and quantity of product, has commonly little control; the principal item of cost, apart from the saving of labor, which he can aspire to reduce, is that of fuel. To determine the limits of possibility in this direction is clearly the first step in d practical inquiry; and this step is represented herewith in Fig. 1, a diagram showing the total useful effect obtained from a pound of fuel under various conditions, and thus permitting direct comparison, under any given conditions, between actual results and the maximum possible results. The following statements will explain the basis upon which this diagram has been constructed. One pound of fuel, containing 90 per cent. of fixed carbon (which represents average conditions), is taken as the unit. The degree of oxidation of the carbon is measured by the ratio of the two oxides of carbon contained in the top-gases. It is necessary to remember that a considerable quantity of carbon is brought in as carbon dioxide by the flux, and to take account of it and of its condition. It is here considered that the carbon dioxide liberated by the limestone does not affect the analysis of the toll-gases, and that the ratio of CO to CO., will remain unchanged by the addition of limestone; enough CO, being reduced by the solution

Sep 1, 1905

By A. J. Partos

One Liberty Place, at 315 m is the tallest building in Philadelphia, PA USA. It is supported on drilled piers socketed in heterogeneous rock. 3832 kN/m2 end bearing and 383 to 766 kN/m2 shaft resistances were selected. Design load distribution was 40% on the base and 60% by shaft resistance. The maximum compression on the corner core columns is supported by clusters of 3 drilled piers. In order to confirm load distributions along shaft and at the base, Drilled Pier G-10 supporting T13-A type outrigger column was instrumented. This column supports 53,849 kN compressive load which includes 13,440 kN windload. This paper reveals details about the process to select the final design for One Liberty Place together with pertinent Information about site geology, foundation construction, quality control, and methods of steel erection. It also presents detailed Information on the type of Instruments, their calibrations, field fabrication, and installation in the shaft of Pier G-10. Readings of concrete temperatures, computed loads, and load distributions are presented for a period from October 1985 through May 1988. The building was completed in 1987.

Jan 1, 1989

A composite iron ore-reductant pellet is a mixture of fine iron ore and fines of coal/char/coke, bonded at essentially room temperature with sufficient green strength for subsequent handling. In ironmaking, these pellets offer the advantage of fast reduction, utilisation of fines, non-coking coal and coke breeze. The composite pellet-based alternative ironmaking processes constitute a promising route for ironmaking in future. The present paper is a brief review of kinetics and mechanism of reduction of iron oxides into iron and other associated reactions, when these pellets are heated to high temperature. It would draw significantly from investigations conducted by the author and his co-workers.

Jan 1, 1999

By Emily Wortman-Wunder

As the 2010 president of the Society for Mining, Metallurgy, and Exploration, Inc., I am pleased to present the 2010 issue of Transactions of the Society for Mining, Metallurgy, and Exploration, Vol. 328. A significant portion of the contribution that we as a professional society make is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable transfer of technology. Communication within the mining community is the key to a successful society. Through books, magazines, meetings and electronic media, we accomplish the technology exchange that is fundamental to the existence of the Society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, Pennsylvania, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume certainly fulfills that pledge. The 2010 Transactions is the first Transactions to take advantage of new publication technologies. It appears solely as an e-book. The decision to go to an all-digital format for this longstanding publication was a difficult one, but one which will certainly better serve the mining community. I am excited about this development and the opportunities it presents. The 2010 Transactions also contain some of the most exciting research from the past year, including new developments in mineral processing, safety and exploration. Be sure not to miss the two Minerals & Metallurgical Processing issues on the subject of gold hydrometallurgy. This 2010 Transactions comprise of a total of 78 technical papers (582 pages including index), including all 21 papers (136 pages) that were published in 2010 in the Technical Papers Section of Mining Engineering magazine (Vol. 62) and all 34 papers (231 pages) that were published in 2010 in Minerals & Metallurgical Processing (Vol. 27). Addition, this volume contains 23 papers (194 pages) that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All 78 technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2010 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2010

By Floyd D. Varley

Outbursts, the sudden and violent out- pouring of material into mine openings, is a ground control problem increasingly encountered in the United States as deeper seams are developed. Outbursts, caused by several mechanisms, are the result of the loading of ground support systems be- yond their designed capacity to failure, manifested in a violent release of stored energy. There are several types of outbursts typical to deep underground coal mines. - Outbursts of the coal face due to the presence of pressure abutments in close proximity to the face. These outbursts are usually accompanied by liberation of large amounts of methane. - Instantaneous convergence of the ribs and floor due to overloading and failure of ribs which lengthens the beam of floor strata sometimes resulting in a chain reaction failure of the mine floor. - violent failure of the confined core of a pillar due to rapid loading beyond the yield point of the pillar.

Jan 1, 1986

By William R. Yernberg

The Fifth International Conference on acid rock drainage (ICARD 2000) was held May 21-24, 2000, in Denver, CO. The three-day conference consisted of about 150 oral presentations and poster sessions that described the state-of-the-art of acid-rock-drainage (ARD) science and technology. The conference also featured a trade show. It included representatives from consulting companies and government agencies with interests in ARD, as well as other environmental issues related to mining. The conference also included field trips to ARD treatment sites and short courses on acid rock drainage issues. ICARD 2000 was planned and promoted by the ICARD 2000 Organizing Committee and the Society for Mining, Metallurgy, and Exploration, Inc. (SME). Financial support was provided by Barrick Gold, BHP Copper, Homestake Mining, Noranda, Phelps Dodge, PlacerDome, the US Bureau of Land Management, the USEnvironmental Protection Agency and the US Geological Survey. Since the original ICARD was held in Roros, Norway, in 1988, knowledge has improved of the behavior of mine wastes as have methods of environmental mitigation. The ICARD 2000 presented the latest advancements in the field of acid drainage.

Jan 1, 2000

By K. S. Lackner, T. M. Yegulalp

We present a review of research and development for coal based clean energy systems aiming for zero emissions to the atmosphere. These systems can utilize all kinds of coal or other solid carbon sources such as tar sands as well as liquid hydrocarbons. The chemical energy of carbon is transferred to hydrogen and used in power generation, in fuel cells, or hydrogen combusting turbines. The waste products of these future power-generating systems are ash, sulfur compounds and CO2. We also summarize current and developing technologies for processing of CO2to produce mineral carbonates for permanent disposal, and associated byproducts.

Jan 1, 2003

The Golden Cross mine is situated in a sensitive environmental setting on the North Island of New Zealand, about 150 kilometres south-east of Auckland and about 8 kilometres NW of Waihi. The mine is situated in dipping topography, with volcanic ashes making up soils, fault zones running through the area, and rainfall of about 3 m per year on average. Water management is the most demanding environmental challenge on site, and a comprehensive programme has been put in place to address tailings deposition, long term tailings storage, and water treatment during and after operations.   The tailings impoundment is built with an underdrainage system that collects groundwaters and waters that seep through the impoundment. The embankment and impoundment are both built to withstand the Maximum Credible Earthquake and the Probable Maximum Flood. Tailings are treated to remove cyanide and to decrease metal solubility to reduce long term risk to water quality after mining. A state-of-the-art water treatment plant is utilised to treat water from the underdrainage system and water decanted from the top of the tailings pond and stormwaters to remove residual cyanide and metals to extremely high standards with a great deal of reliability and at reasonable cost. Closure of the facility addresses long term post mining water quality issues, and rehabilitation of the area with wildlife habitat as a priority.

Jan 1, 1995

By Garry Biles

The Eskay Creek Mine is a high-grade gold and silver underground mine in northwestern British Columbia. The mine started operations in late1994. For the first three years, ore was crushed to -50 mm(-2 in.), blended to satisfy smelter terms and shipped to smelters in Japan and Canada. Preliminary evaluations indicated that a complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. So markets for raw ore were identified and underground mining and ore transportation operations began at a production rate of 300 t/d (330stpd).

Jan 1, 2000

By W. J. Guay

Carbonaceous gold ores containing gold dispersed in sulfides are refractory to cyanidation because: (1 ) the carbonaceous materials adsorb gold during cyanidation; (2) a portion of the gold s so finely dispersed in the sulfide mineral lattice as to preclude contact with cyanide solution; and (3) a portion of the gold is chemically combined with carbonaceous material. Techniques which have been used to treat these ores are: (1) roasting or chemical oxidation to decompose sulfide and carbonaceous materials; (2) flotation to reject carbon; (3) the use of kerosene or other reagents to passivate the adsorptive carbon compounds; (4) carbon or resin in pulp; (5) flotation of a bulk concentrate which is treated by one of the above methods; and (6) the use of chelating agents which have a stronger affinity for gold than the activated carbon in the ore.

Jan 1, 1981

By A. D. Storrie

An underground wet shotcrete trial was completed last year to determine the effectiveness of wet shotcrete as an alternative support mechanism to dry shotcrete in the kimberlite environment. The wet shotcrete was manufactured at the underground batch plants, transported to site using an agiecar and transferred to the shotcrete pump. The wet shotcrete is pumped to the nozzle where compressed air at 7 bar and an accelerator, Meyco SA 160, is added and enables the shotcrete to be placed successfully onto the tunnel wall. No tunnel guard was previously placed on the sidewall and hangingwall. Geotechnical testing indicates that the Grace fibre performed extremely well with the energy absorption tests at 7 kg/m3and 8kg/m3where both achieved over the mine requirement of 750joules. The Grace fibre and wet shotcrete mix also achieved a compressive strength in excess of 55 MPa, well above the 45 MPa requirement for Premier Mine. The recommended wet shotcrete mix design is therefore based upon: [Material/ CriteriaQuantity/m3Units ?Lafarge 42.5 Duratech500kg ?Condensed silica fume40kg ?Rayton Sand1.558Ton ?Delvocrete stabilizer 103.6litres ?Glenium 27CH5.4litres ?Meyco TCC 7355litres ?Water230litres ?Meyco SA16025litres ?Fibre8kg ?Cement/Water Ratio2.35? ?Water/Cement Ratio0.43? ?Flow615 mm] If the wet shotcrete system is implemented there is a potential for Premier Mine to make major savings. In South Africa there are two suitable wet shotcrete machines available for the mining industry, the Spreymec, manufactured by Tamrock and the Fermel/Meyco wet shotcrete machine. The Spreymec is a fully imported machine. The Fermel component is manufactured in South Africa and the Meyco shotcrete components are imported and supported by MBT (Master Builder Technologists) in South Africa. The Fermel/Meyco machine is assembled in South Africa. Premier Mine has allocated some R2, 100,000 towards the implementation of the wet shotcrete system. If implementation is successful there should be an internal rate of return gain of 76% with regard to this project.

Jan 1, 2001

By R. J. Leary

This investigation was conducted to determine the effects of various rare-earth metal addition practices upon the macrostructure and the pattern of sulfur distribution in steel ingots. Heats of plain carbon steel were melted in a 1-ton, basic electric-arc furnace. Melts were treated with mixtures of rare-earth silicides, aluminum, and cryolite either in the furnace before tap or in the ladle after tap to determine the effects of this form of rare-earth treatment upon ingot macrostructure. Steels thus treated with rare earths in the furnace were characteristically free of the gross subsurface nonmetallics which typically result from conventional rare-earth treatments. Steel treated in the ladle showed only a few such nonmetallics, and practical techniques were developed for eliminating most of these. Results showed that furnace deoxidation was controlled by the concentration ratio of rare earths: aluminum. During casting, deoxidation was controlled by the concentration of rare earths. Oxygen contents equivalent to vacuum ladle degassing resulted from air-melt furnace treatments with the rare-earth mixtures described. Rare earths in steel inhibited the onset of equiaxed grain formation during ingot freezing, and also virtually prevented interdendritic segregation of sulfides.

Jan 1, 1968

By J. W. Thompson

Be if enacted by the Senate and House of Representatives of the United States of America in Congress assembled, That deposits of coal, phosphate, sodium, oil, oil shale, or gas, and lands containing such deposits owned by the United States, including those in national forests, but excluding lands acquired under the Act known as the Appalachian Forest Act, approved March 1, 1911 (Thirty-sixth Statutes, page 9G1), and those in national parks, and in lands Withdrawn or reserved for military or naval uses or purposes, except as heroinafter provided, shall be subject to disposition in the form and manner provided by this Act to citizens of the United States, or to any association of such persons, or to any corporation organized under the laws of the United States, or of ;iny State or Territory thereof, and in the case of coal, oil, oil shale, or gas, to municipalities: Provided, That the United States reserves the right to extract helium from all gas produced from lands permitted, leased, or other- wise granted under the provisions of this Act, under such rules and regulations as shall be prescribed by the Secretary of the Interior: Provided further, That in the extraction of helium from gas produced from such lands, it shall be so extracted as to cause no substantial delay in the delivery of gas produced from the well to the purchaser thereof: And provided further, That citizens of another country, the laws, customs, or regulations of which, deny similar or like privileges to citizens or corporations of this country, shall not by stock ownership, stock holding, or stock control, own any interest in any lease acquired under the provisions of this Act.

Jan 1, 1921

By R. H. Adams, A. M. Khan

The Huntington Beach oil field is on the Pacific Coast, southeast of the City of Los Angeles (Fig. 1). It lies both onshore and offshore. Most of the onshore section is operated by Standard Oil Co. of California, WOI. The Tar reservoir is of upper Pliocene age, about 200 ft thick, and consists principally of fine-grained, unconsolidated, somewhat shaly sand, with thin inter-bedded shale stringers throughout (Fig. 2). The reservoir is a broad, highly faulted, elongated anticline, with an areal extent of about 370 acres. Most of the faults bisecting the structure are normal, trend north-south, and are the main cause of reservoir discontinuity (Figs. 3 and 4). From 1964 to Dec., 1967, 259 steam stimulations were performed on a total of 125 Tar sand wells. Eighty-six new wells were drilled and steam stimulated. Of the total, 96 have been stimulated twice, 34 three times and 3 four times. During this same period, a two-injector steam drive pilot has been in progress. The response obtained from this project has been compared with the response to cyclic stimulation. This paper presents an analysis of the field observations for the two methods of thermal recovery. History of Development Drilling to the Tar pool commenced in 1924 with an initial well production of 40 to 50 B/D of 12o API gravity oil. Complete primary development of the pool has been spread over several years. Approxi- mately 40 wells were drilled during the first phase of development, which was completed in 1945. The subsequent primary development started in 1960 with initial well productions of 30 to 40 B/D oil. Thirty-seven wells were completed in the Tar pool during this phase. For the most part, slotted, gravel flow packed liners have been used in the wells in this pool. A cyclic steam stimulation pilot was initiated in March, 1964. Based on the very successful stimulation in the pilot area, the cyclic stimulation project was expanded to include all of the Tar pool wells producing at the end of 1965 (Fig. 5). Also, a development drilling program was begun at this time. To date, 86 new wells have been drilled under this program. The number of wells drilled each year in this secondary phase of development is also shown in Fig. 5. New Well Completion Practices Most of the new wells have been completed to produce from both the Upper and Lower Tar zones. Generally, a casing stub is cemented from the top of Lower Tar to the base of clean Upper Tar sands to exclude intermediate water-bearing sands. The water string is then cemented from the top of Upper Tar to about 1,500 ft with neat cement and 30 percent silica flour. The annulus from 1,500 ft to surface is then filled with a petroleum-based gel through a high-temperature port collar. Once again, a history of sand-free production dictated the use of 60-mesh gravel flow packed liners. The Upper and Lower Tar

Jan 1, 1970

Operator efficiency and control capability along with cost effectiveness have been the quest of mining, industrial, and mobile hydraulic engineers for years. The majority of the functions in present day fluid power systems are controlled by on/off control valves. They are inexpensive and provide easy installation and operation, but they lack the quality of fine control of load flow or what is sometimes known as "feathering the load". An alternate approach to obtaining this capability is the use of electro-hydraulic servo-valves, but their implementation into a system is complex, and they are expensive. As a result, electrohydraulic systems are still used primarily in the aerospace industry. Of late, a compromise seems to have evolved between the on/ off control systems and the servo-technology is the so-called proportional flow control valves. A proportional flow control valve meters fluid to the load in proportion to the input command from the operator. In principle, it is similar to a conventional flow control valve and is tailored to meet the control requirements from the load point of view. The hydraulic system using this valve usually works in an open-loop mode with the operator closing the loop. Incorporating load-sensing mechanisms and adoption of electrical/electronic signalling into the valve make it the "ideal valve" which designers have been looking for from a techno-economic point of view.

Jan 1, 1983

The environmental impact of solid waste materials is closely linked to their potential to produce a hazardous leachate once deposited in a landfill. This potential is conventionally assessed with simple laboratory batch leach tests, which find more and more frequent application also in the minerals and metals industry. Such tests are intended to help distinguish between high and low risk wastes, but are completely unsuitable to allow quantitative prediction or modelling of the long-term leachate generation potential. In the present approach the leachate generation process is perceived as a combination of bulk convective transport, stagnant zone and inner particle diffusion, as well as reaction kinetic effects. Model equations are formulated accordingly. A modelling frame work, WASTESIM, has been developed at UCT, which allows flexible combination of the model components and simulation of leach scenarios. Quantitative model parameters are obtained from a systematic laboratory study on the waste material in question. The combined assessment and modelling approach is demonstrated with a study on Cr (VI) leaching from a ferro-chromium slag material. Although not straightforward, the approach is particularly useful in determining long-term liabilities in the context of waste disposal sites with considerably more reliability than has previously been possible. Keywords: waste deposits, waste leaching, heap leaching, environmental, risk assessment, Cr (VI), ferro-chromium, slag.

Jan 1, 2000

By B. P. Watson

The Bushveld platinum group metal deposits are two distinct, shallow-dipping stratiform tabular orebodies which strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 300 m. The mining method is a variation of planar open stoping. Pillars are widely employed to support the open stopes. In the deeper levels, in-stope pillars are required to fail in a stable manner soon after being cut, and the residual pillar strength is used to stabilize the hanging wall. These pillars are commonly known as crush pillars. Little work has been done in the past to determine pillar peak and residual strengths, and pillars have been designed using experience and formulae developed for other hard-rock mines. This has led to over and undersize pillars with consequential loss of ore, pillar bursts and potential collapses. This paper describes a crush pillar design methodology, and provides design charts. Three mining environments were incorporated in the investigations, which included underground and laboratory measurements, analytical solutions, numerical model sand back analyses. The results of the study are suitable for the areas where the research was carried out, and may also be applied with caution in other similar environments.

Jan 1, 2010

By John Hoffert, Darren Colwell, Greg Tucker, Jeremy Kinch, Greg Rasmussen

"The Kemess Mine, a major producer of gold and copper, is located in north-central British Columbia. Kemess was brought into production in May 1998 by Royal Oak Mines. On February 11, 2000 Northgate Exploration Limited acquired Kemess Mine from receivership. Since acquisition in 2000 Kemess has seen many accomplishments, including the reduction of costs by 40%.One of the largest site capital costs was the construction of the tailings storage facility dam, which when finished will be one of the largest earth filled dam structures of its type. The existing construction design by AMEC called for a kilometer wide rock dam to be built from the 1350 M elevation to the 1504 M elevation at a 5.5:1 slope by hauling over 30 million tonnes of non-acid generating waste rock 7-kilometers from the open pit to the tailings dam, which was highly expensive.Kemess realized an opportunity for cost reduction was possible if the dam could be built from suitable quality tailings sand; however the sand did not meet the neutralizing potential ratio specifications. It was determined that cycloning combined with flotation to reduce pyrite concentration in the sand would produce a non-acid generating product for dam construction. The sand plant design challenges were to remove the sulphides from the tailings to obtain an NPR greater than 2:1 and provide a consistent sand product for the construction with a fines content of less than 15% passing 200 mesh. After a 2-year testing design and construction period, the sand plant was successfully started at the end 2002 resulting in higher than expected sand quality and production rates.This paper describes the plant design phase, commissioning, and operation of the tailings sand plant for construction of the tailing storage facility dam to enable us to meet all the engineering and regulatory requirements. The many challenges faced were successfully met using several innovative designs. The operational, economic, and environmental benefits are detailed."

Jan 1, 2004

By Laura Bastemante, Bruce Vandenberg, Fred Huettig

Recent advances in solid-state, field portable, fast framing video camera systems and PC based frame capture hardware now allow blast imaging up to loo0 frames per second. Up to 8 seconds of data can be stored directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the KineView 1256P system and compare these with the analogous aspects of film based cameras.

Jan 1, 1997

By M. Castelli, C. Scavia, S. Marello, A. Allodi

ABSTRACT – This paper investigates the possibility of interpreting the shear band evolution in hard soils and soft rocks as the result of shear propagation from pre-existing natural defects. Thesis done through the application of the principles of Fracture Mechanics, a Slip-Weakening Model(SWM) being used to simulate the non-linear zone at the tips of the discontinuity. Experimental observations have been carried out on prismatic samples of Beaucaire marl through biaxial compression tests in plane strain conditions. A numerical simulation confirms the validity of the proposed approach. RÉSUMÉ – Cet article présente la possibilité d’interpréter l’évolution des bandes de cisaillement dans les roches tendres et les sols raides comme le résultat de la propagation pour cisaillement à partir d’un défaut préexistant. Le Slip-Weakening Model (SWM) a été employé pour modéliser la zone non linéaire a l’extrémité d’une discontinuité. Nous présentons des observations expérimentaux obtenues à travers des essais de compression en déformation plane sur des échantillons prismatiques de marne. La simulation numérique d’un essai confirme la validité de la méthode proposée. KURZFASSUNG – Die vorliegende Arbeit versucht die Ausbreitung von Scherzonen in(bindigen) Böden und im Lockergestein anhand der Entwicklung von Scherrissen ausgehend vonexistierenden Schwachstellen zu erklären. Die Umsetzung erfolgte mit Hilfe der Bruchmechanik,für die Modellierung der nichtlinearen Zone an den Rissenden wurde ein Slip-Weakening-Modell(SWM) eingesetzt. Es wurden zweiaxiale Druckversuche an prismatischen Probekörpern vonBeaucaire Mergel unter der Bedingung eines ebenen Verzerrungszustandes durchgeführt. Dienumerische Untersuchungen bestätigten die Annahmen der untersuchten Theorie.

Jan 1, 2003