Search Documents

By Sarah Beutner Mavrogenes

The mineralogy of three slags from a domestic secondary copper refinery were studied by applied mineralogical techniques to determine the: 1) phases present, 2) phase chemistry, 3) phase abundance, 4) associations, 5) crystalline habit, 6) grain size, 7)microtextures, and 8) causes for certain metallurgical problems, such as metal losses to the slags. The slags were produced by skimming the bath prior to melt-down to allow heat from the flame to reach the bath. The first slag is highly viscous and all three slags contain a large amount of copper. The "first slag", which is skimmed prior to treatment of the bath with fluxes, contains metallic copper, cuprite, delafossite, magnetite, Mg-hercynite, common spinel-chromite solid solution, picrochromite-chromite solid solution, common spinel-picrochromite solid soiution, gahnite, cassiterite, silica-rich glass, and corundum. Its abundant solid refractory phases make the slag difficult to skim. The "soda-rich slag", skimmed after the treatment of the bath with sodium carbonate flux, contains cuprite, delafossite, magnetite, cassiterite, Na-Al-silicate, and Na-Al-Ca-silicate. It contains less metallic copper than the first slag and lacks the refractory minerals. The "phosphorus-rich slag", skimmed after treatment of the bath with a copper phosphide flUX, contains metallic copper, cuprite, delafossite, berlinite, cassiterite, silica, apatite, Cu-Fe-rich apatite, copper phosphate, Cu-Fe-phosphate, and a Pb-phosphate. In contrast to the above three copper-rich slags, recent charges have produced a silver-copper-rich slag. The "silver-rich slag", skimmed after the treatment of the bath with a copper phosphor ide-borax flux, contains, cassiterite, delafossite, cuprite, a Na-Al-silicate, magnetite, metallic copper, MgO, common spinel-chromite solid solution, and wollastonite. Silver ranging from 0.05 to 2.02% was found by atomic absorption and inductively coupled plasma spectrometry analyses in the metallic copper phase.

Jan 1, 1989

By J. A. Bustnes

The present work deals with kinetic studies of the reduction of molybdenum- and tungsten oxides by hydrogen. The experimental method used was therrnogravimetry under isothermal as well as non-isothermal conditions. The non-isothermal kinetics in the case of the reduction of MOO, to Moo2 has been modeled considering surface reaction as rate- controlling. In the case of the reduction of W02 to W a model was developed on the basis of the movement of the reaction front. The activation energies calculated on the basis of the models were in good agreement with those derived from isothermal experiments.

Jan 1, 1994

By I. S. Blair

The Mufulira smelter (1, 2,' 3, 4,) is one of three smelters situated on the Zambian Copperbelt to treat concentrates and other intermediate products produced in the area. Two mining companies, Roan Consolidated Mines Limited (RCM) and Nchanga Consolidated Copper Mines Limited (NCCM) each have 51% Zambia Government participation. RCM operates two smelters, one at its Mufulira Division and the other at its Luanshya Dl vision. NCCM operates one smelter at its Rokana Division (5). The Mufulira smelter was commissioned in 1937 with two reverberatory furnaces and four converters. The final product, blister copper, was cast from a holding furnace. In 1952 two anode furnaces and a common casting wheel were installed to feed a new and adjacent electrolytic refinery. In 1956 the smelter was extended to accommodate increasing production from the new Chibuluma mine and expansion at Mufulira mine. A third reverberatory furnace, a fifth converter and duplicate anode processing and casting facility were added. The Copperbelt smelters suffered a loss of production potential when higher ash content coals were used in reverberatory smelting furnaces from 1966 onwards. This, and the planned production increases from Mufulira and other RCM mines, indicated a smelting shortfall of 55,000 tonnes of copper a year in the combined capacity of the RCM smelters.

Jan 1, 1976

By Lin Li, Xiang Li, Yifang Zheng, Jilai Xue, Jun Zhu

"Al drops and gas bubbles in the anode-cathode space of aluminum electrolysis cell are of great importance for cell operation improvement in metal loss, current efficiency and energy consumption. A direct observation on the Al drop, gas bubble and ultrasound was carried out through a see-through cell. The Al drop immersed into the cryolitic melt was found moving up and down irregularly in the anode-cathode space without electrolysis, which was then completely dissolved into the melt. During electrolysis, the Al drop came to the anode area and reacted with the gas bubbles generated on the anode. Under ultrasound, the gas bubbles were removed from the anode surface while the Al drop was kept on the side of anode. The observed phenomena were useful for technology improvement in reducing the anode-cathode distance or lowering the energy consumption in aluminum electrolysis.IntroductionDuring aluminum electrolysis, aluminum metal drop and anodic gas bubble are in close contact each other within the anode-cathode space, and the interaction between them can produce significant impact on metal loss, current efficiency and energy consumption. The motions of the Al drop and the gas bubble are also related to the dissolution of aluminum metal into cryolitic melt and the cell voltage drop due to the bubble layer covering the anode surface.A number of studies have been carried out using different types of see-through cells, where the dissolving process of metal Al into cryolitic melts (metal fog) in the anode-cathode space was directly observed and photographed [1, 2]. With the similar method, some direct observations on the anodic bubble behaviors with and without ultrasound were performed during aluminum electrolysis [3-6]. However, to our best knowledge, there is no published work on direct observation on the behavior of Al drops and anodic gas bubbles staying together within the same anode-cathode space, as well as the motion and interaction of them in cryolite-alumina melts."

Jan 1, 2011

By Yufeng Guo, Tao Jiang, Jianjun Fan, Haizheng Hao

"Function of High Pressure Roll Grinding (HPRG) in production of oxidized pellets from magnetite concentrate as raw material was systematically studied. It was found that bentonite dosage decreased from 1.3% to 0.8% if specific surface area of magnetite concentrate pretreated by HPRG was up to 2553.41cm2.g-1. The green ball quality improved obviously due to the increase of specific surface area and fine particles content, and the improvements of size distribution and the ballability of pretreated materials. However, the decrease of pellet porosity accelerated the primary solid phase reaction and oxidation reaction, which made the pellets surface form compacted layer that handicapped the diffusion and migration of oxygen, promoting the formation of double layer structure of finished pellet. Consequently, the compression strength of preheated and roasted pellets was not markedly improved by HPRG.IntroductionWith the increase of proportion of pellets in the BF recently, the technical-economic index of BF has obviously been improved. Consequently, the production and the quality of BF pellet are given more attention [1]. However, with the decrease of the quality of iron ore concentrate, the problems such as poor ballability, high bentonite dosage, high preheating and roasting temperature are becoming the great challenges to not only the quality of finished pellets, but also the energy consumption [2, 3]. In order to overcome these problems, mechanical pretreating technologies such as the High Pressure Roll Grinding (HPRG) and Damp-grinding are widely applied. HPRG has a number of advantages such as low energy consumption, high productivity and easy-maintaining. It is more economic and environmentally friendly than the Damp-grinding technology [4, 5]. A great number of experiments have revealed that HPRG can improve the quality of hematite pellets. Although there are some studies of function of HPRG in the magnetite oxidized pellet production, they are not comprehensive and systematic, especially to the preheating and roasting system [1, 2, 6, 7]. Accordingly, the influence of HPRG on the pelletizing system and the preheating and roasting system are systematically studied in production of magnetite oxidized pellets in this article."

Jan 1, 2011

By Yurniko Nakamura

Hydriding properties and crystal structure of a Ti-V- Mn solid solution alloy have been studied by P-C isotherm measurements and neutron and X-ray powder diffraction. The absorption P-C isotherm at 298K shows two plateau regions at 0.01MPa and 1MPa. The X-ray diffraction data have demonstrated that three phases with a BCC, a pseudo-cubic FCC and an FCC structure form subsequently with increase of the hydrogen content. Crystal structure of the latter two phases has been determined by Rietveld refinement of the neutron diffraction data. The FCC phase is the di-hydride of CaF2 type with hydrogen occupation in the T sites. The pseudo-cubic FCC phase is the mono-hydride of NaCl-type with hydrogen occupation in the 0 sites, which has not been reported so far. The lattice constants of the mono-hydride (Ti1.0V1.1Mn0.9)H_2.7 are a'=0.407 nm for two axes and c'=0.390 nm for the third axis. The a'axis is shorter by 4% than the c'axis. This pseudo-cubic FCC lattice is formed by contraction of 5% of the a axis and expansion of about 30% of the c axis from the original BCC lattice.

Jan 1, 2002

By Ernt. W. D.

A membrane based mixed extractant process was developed for selective removal of copper from waste acidic cupric chloride etchant solutions found in printed wire board manufacturing. The process uses a mixture of Adogen 381 (tri-isooctylamine), MOC®-45 (ketoxime) and MOC® 55TD (aldoxime) in a kerosene diluent. The mixed extractants recover the copper from a hydrochloric acid medium and transfers it to a sulfuric acid medium. The process also utilizes unique wetted membranes to separate the aqueous and organic phases. The driving force for these membranes is not pressure but the difference in surface tension between the two phases. By using these membranes, complete phase separation results. There is no physical entrainment contamination as found in conventional systems. The only cross contamination is the solubility concentration of one phase in the other. This however is less than 10 mg/l.

Jan 1, 1998

By Maria K. Kojo

The interaction between various slags and a nickel concentrate containing pyrite, pentlandite, and violarite were investigated by submerging concentrate pellets in molten slags. The slags were contained in MgO-A12O3 spinel crucibles. The slag oxidizes the iron sulfides in the concentrate, resulting in a nickel matte. The amount of S02 gas formed during reaction was measured to determine the oxidation reactivity of the slags. The experimental variables included temperature, the ferric/ferrous ratio of slag, and other slag properties such as the FeO/SiO2 ratio and the MgO and NiO contents. The reactivity of the slag depended in a complex manner on its oxidizing power, viscosity, and interfacial tension. The slag composition for the greatest reactivity was determined to be Fe3+/Fe2+ = 0.3, Fe/SiO2 = 1.3, and % MgO = 2. This slag, however, caused substantial foaming. Increasing the MgO content to 10% or replacing it by 5% MgO + 8% NiO eliminated at a slight decrease in reactivity. The implications of the findings from this work in the bath smelting of nickel sulfide concentrates are discussed.

Jan 1, 1995

By G. S. Gupta

To predict the iron oxide concentration a mass transfer model has been developed for an Induction Smelting Process (ISP) in which self-fluxed composite pellets (made of iron ore, brown coal and lime) are melted in a single phase induction furnace in conjunction with top blown oxygen. Transient mass balance equation with complex boundary conditions has been worked out by adopting a relatively new approach known as the cell model approach. These equations have been solved numerically using finite difference technique to obtain the iron oxide concentration profile in the ISP. Numerical and experimental results obtained for iron oxide concentration show a reasonable agreement with each other.

Jan 1, 1991

By Maria de Campos

The pre-reduction behaviour of chromite particles in methane-argon and methane-hydrogen gas mixtures was investigated between 1050°C and 1250°C. Loose bed of chromite particles were reacted in a vertical tube furnace under a pre-set gas mixture predetermined time intervals. Metallization results were obtained for the Cr and Fe components by chemically analyzing the reaction products. SEM-EDAX techniques and X-ray diffraction were employed to elucidate the reduction mechanism. It was found that higher reduction kinetics and higher Cr:Fe ratios in the metal phase would be achieved when hydrocarbon gas was used in comparison to classical carbothermic reduction at a given temperature. The reduction rate was generally bulk gas mass transfer controlled to the reaction site for initial stages which then was followed by ionic diffusion rate control. It is proposed that methane did not partake directly in the reduction but cracked, presenting the reaction site with hydrogen gas and atomic carbon, which was able to immediately react at the immediate area of reduction regeneration CO and H2 and thus maintaining a low partial pressure of oxygen at the reaction site.

Jan 1, 2006

By Hidefusa Takahara, Koichi Miyake, Dierk Raabe

"Mechanical properties of copper wires were examined. The copper wires containing 5-10 mass % chromium and 1-3 mass % silver were produced through heavily cold deformation. It was expected that the copper wire was easily fractured during cold deformation because of the existence of brittle chromium phase in the alloy. In fact, the copper wire was fractured due to large work hardening, when the true strain [n] exceeded 5. However, the copper wire annealed at 1273K for 6 ks ·in the middle of deformation process could be smoothly drawn to 11=8. After precipitation treatment for silver phase at 473k for 1.8 ks, the wire was able to further drawn to n=8.4. The final deformed wire showed tensile strength higher than 1200MPa.IntroductionDownsizing of electronic devices has led to the demand of finer and higher strength materials for cables. Conventional copper alloys have about 800MPa in ultimate tensile strength. These strength are mainly obtained by precipitation hardening. Nowadays, a process for higher strength wire has been developed, where dual phase copper alloy is used. When it is drawn heavily, the' second phase is elongated along drawing direction and the wire gets high strength due to fiber reinforcement (1). That alloy is so called in-situ formed fiber reinforced ·alloy. Cu-Ag(2), Cu-Nb(3) and Cu-Cr(4) systems are well known as such alloys. It is also well known that chromium is brittle material except single crystal and high purity of chromium. However, Mihara et al. C5l have achieved 1 GPa in ultimate tensile strength in the Cu-Cr-Zr and Cu-Cr-Ti alloys by appropriate thermo-mechanical processing.In this study, the Cu-Cr-Ag systems were investigated: The alloys contained 10 or 5% chromium and 3 or 1 % silver. It was demonstrated that silver precipitated in copper matrix contributed on further hardening."

Jan 1, 2000

By F. J. J. van Loo, A. A. Kodentsov, J. A. van Beek, M. R. Rijnders

"A periodic layered morphology of the reaction zone has been observed in several annealed solid/solid diffusion couples, including metal/metal and metal/ceramic couples. This morphology is characterized by a regular array of alternating layers, which are either single-phase layers or bands of particles embedded in an intermetallic matrix phase. A description of several systems showing periodic layer formation is given. It is shown that the periodic layered structure with the single phase layers and the one with the bands of particles have a different mechanism of formation.IntroductionSolid state reactions in ternary systems can produce a variety of reaction zone morphologies if there are two or more reaction products. Three types of morphology have been described in detail: 1) simple layered; 2) isolated precipitates in a singlephase layer; 3) interpenetrating columnar (lamellar) or interwoven structure. Understanding the factors that govern the formation of different morphologies is of importance in many fields of engineering. For solid state displacement reactions the conditions governing the formation of these morphologies are well understood [1-4]. For example, the development of a layered or aggregate reaction zone depends on the relative diffusivities of the components through the reaction products.This paper is concerned with the periodic layered morphology which has been observed in various solid state systems. We consider this to be a fourth type of reaction layer morphology. Two manifestations of periodic layered morphology may be distinguished. One form consists of regularly spaced layers of particles of one reaction product embedded in a matrix phase (another reaction product). The other form consists of single-phase layers embedded in a matrix phase. It will be shown that each manifestation has its own mechanism of formation. In section A we consider a system (Ag/Ti-foil/Si) in which periodic layer formation will be explained as a special case of the Liesegang phenomenon. In section B we consider systems where the periodic layered structure has a different origin."

Jan 1, 1996

By Fathi Habashi

Nitric Acid has been used for over 50 years in the uranium industry and in phosphate fertilizer manufacture. Its application in the treatment of sulfide concentrates is relatively recent. A review of recent developments is given.

Jan 1, 1999

By Steven M. Puricelli

Sulfuric acid plants associated with smelters, have historically been an overworked and often neglected pollution control device. They could do little more than manage the wide fluctuations in gas flow and SO2 strength from the smelter. With the introduction of flash smelting, the picture began to change, but the fluctuating batch converters continued to dictate acid plant design. More recently, the commercial use of continuous converting processes utilizing high levels of oxygen enrichment has dramatically upgraded the SO2 strength and stabilized the gas flow to the acid plant. The SO2 gas now issues continuously and at concentrations that allow for compact and, cost effective acid plants. Relieved of the burden of excessive dilution air, the heats of reaction can also be recovered as medium pressure steam and used to drive a generator, making the acid plant a net producer of power and a valuable asset to balance sheets. This concept was put into practice at the Kennecott Utah Copper Corporation smelter modernization project, located in Salt Lake City, Utah. The new acid plant, which was commissioned in June of 1995, is a sophisticated, low environmental impact, energy producing plant, worthy of review. This paper examines the key features of this acid plant, such as controlling its tail gas, by catalysis alone, to an environmentally friendly, 100 ppm of SO2, while feeding the acid plant converter with an efficient 14% SO2. The acid plant is also a prudent steward of energy resources, recovering 220,000 lb/hr of 140 psig steam from process heat which is used to generate a substantial 20 MW of gross power. Also discussed will be some of the ongoing issues, such as handling of selenium and fluorine in the gas cleaning sections, as well as a review of some. of the problems that were identified and resolved. Today's modem acid plants, by necessity, are becoming a producer of quality, valuable products, making the acid plant an asset and not a liability. Plants like Kennecott are already gaining wider acceptance and are expected to be the vision of the future.

Jan 1, 1998

By Lee Fergusson

"The primary features of ViroMine™ Technology are introduced and applications of ViroMine™ Technology to mine site remediation and the treatment of a variety of intractable waste-streams, including a technical discussion of acid neutralizing capacity, metals binding capacity and longterm stability of results. Outcomes from four applications at high-profile international mine sites are presented: 1) the superfund site at the Gilt Edge Mine, South Dakota, USA (four years of data on the treatment of acidity, TDS and metals such as Al, Co, Fe, Mn and Zn); 2) one of Australia’s most polluted sites at King River Delta in Tasmania (treatment of TAA and TPA, and metal and metalloid contaminants such as As, Cr and Hg); 3) The Aljustrel “Aqua Forte” mine site in Portugal (high acidity, metal and metalloid contaminants such as Al, As, Cu and Zn) and 4) the Ulsan Iron Ore Mine at Ulsan, South Korea (treatment of metal and metalloid contaminants such as As, Cd and Ni).IntroductionThe commercialisation of ViroMine™ Technology has resolved some of the most intractable pollution issues associated with historic mining ventures on a global scale and has facilitated the neutralisation of Acid Rock Drainage (ARD), remediation of acidic and metal contaminated impoundments (including tailings dams) and promoted revegetation on tailings deposits and waste rock dumps. ViroMine™ Technology also enables current mining ventures to manage effluent simply and efficiently to meet increasingly stringent environmental standards and is enabling the mining sector to reconceptualise the management of mine spoil. The abilities of ViroMine™ reagents to neutralise the actual and potential acidity of sulphidic mine spoil coupled with the ability to bind metal and metalloid contaminants into non-bio-available forms are the key features delivering environmental and economic benefits to the mining sector and the broader community. Results from four projects utilising ViroMine™ Technology are presented to highlight the suitability of ViroMine™ Technology to treat all forms sulphidic mining wastes. 37"

Jan 1, 2008

By O. E. Omotoso

This study is part of an ongoing investigation to understand the mechanism of stabilization/solidification of hazardous chromium wastes in ordinary Portland cement (OPC). Tricalcium silicate (C3S*),a major component of OPC is mixed with reagent grade Cr(lll) and Cr(VI) solutions, to simulate complex cementiCr waste systems. Scanning electron microscopy (SEM) and energy disperse spectrometry (EDS) were employed to provide microstructural and chemical information. Transmission electron microscopy (TEMlEDS), apart from complimenting the SEM, was used to probe the distribution of Cr in the hydration products of C3S and to provide crystallographic information. 29Si MAS NMR (magic angle spinning - nuclear magnetic resonance) Was used to characterize the influence of Cr on the hydrated silicate structure.

Jan 1, 1995

By José R. de Tenorio

The aim of the present work was to investigate the reduction process of MnO~FeO-Si02 slags by carbon-saturated liquid iron. The effect of the initial Mn content in the bath was explored. The initial Mn content was in the range of 0 up to 40 wt. %. The MnO content in the slag was kept constant at 40 wt. %. Tests were performed in laboratory apparatus. Samples of slags and bath were taken. In the first 5 minutes, it was observed a very strong reduction of FeO. This first step promoted a MnO-Si02 enrichment of the slag and a formation of CO bubbles, which increases the slag level. The increase ofMn content decreases the MnO reduction rate.

Jan 1, 1996

By Kenneth C. Mills

Interfacial phenomena can have a dramatic effect on the separation of phases. Furthermore, since they involve surface-active materials, concentrations at ppm levels are enough to cause dramatic effects on separation processes. The effects of (i) emulsification, (ii) contact angle and wettability and (iii) Marangoni flows on phase separation are reviewed.

Jan 1, 1999

By K. Narayana Swamy

Experimental results of 3-phase mixing in a physical model of a CCRL for metals refining, at high levels of bottom gas injection (up to a superfIcial gas velocity (Us) of 12.5 cm/min), are presented. A thermal tracer technique was used to elucidate both longitudinal mixing and interphase heat transfer. The results indicate that even under conditions of significant bottom gas injection, it should be possible to maintain acceptably low longitudinal mixing (D. < 20 cm2/s and D/uL < 0.1) in the CCRL. Interphase mass-transfer coefficients of the order of 0.02 cm/s and higher, are predicted from the measured interphase heat transfer coefficients using the mass and heat transfer analogy. Adequate performance is likely to be possible for an industrial CCRL, based on extrapolation of these results to full-scale conditions.

Jan 1, 1996

By Brian G. Thomas, Quan Yuan, Rajneesh Chaudhary, Rui Liu, Sana Mahmood

"A particle-entrapment model based on local force balances has been developed, implemented into computational models of turbulent fluid flow, and applied to simulate the entrapment of slag inclusions and bubbles during the continuous casting of steel slabs. Turbulent flow of molten steel is computed in the nozzle and mold using transient CFD models. Next, the transport and capture of over 30,000 particles are simulated using a Lagrangian approach. Particles touching the dendritic interface may be pushed away, dragged away by the transverse flow, or captured into the solidifying shell according to the results of a local balance of ten different forces. This criterion was validated by reproducing experimental results in two different systems. Finally, the model is applied to predict the entrapment distributions of different sized particles in a typical slab caster. Although more large particles are safely removed than small ones, the capture rate as defects is still high.IntroductionSurface defects such as slivers and blisters are often caused by captured inclusion clusters, slag, bubbles, and other particles. During continuous casting, jets of molten steel from the submerged entry nozzle (SEN) ports carry bubbles and inclusion particles into the mold cavity from upstream processing, as shown in Figure 1 [1]. In addition, droplets of liquid mold slag may become entrained into the flowing steel due to fluid flow problems, via several different mechanisms [2]. Figure 2 shows some typical inclusion particles [3] that can be entrapped from the flowing liquid into the solidifying steel shell to form defects in continuous-cast product.Liquid steel flow in the continuous casting mold has been modeled extensively. Reynolds Average Navier-Stokes (RANS and URANS) approaches are based on accurate computation of the ensemble-averaged velocity field. Particle transport can be tracked using a Lagrangian approach, introducing an extra model, such as ""random walk"" to generate realistic motion of every particle. Large Eddy Simulation (LES) models can accurately calculate both the transient evolving flow field and Lagrangian particle motion [4, 5] of this turbulent process."

Jan 1, 2012