Search Documents

By Stephen Chryssoulis, Stamen Dimov

Detection and quantification of precious metals (Au, Pd, Pt, and Rh) in spinels and silicate minerals is important for establishing the maximum attainable recovery by sulphide flotation. To achieve this goal subpart per billion (ppb) detection limits are required plus the ability to quantify results. Existing quantitative microbeam techniques (EPMA, PIXE, SIMS, TOFLIMS) have limits of detection in the O. l-200ppm range. Time-of-flight resonance ionization mass spectrometry (TOF-RIMS) is a microbeam analytical technique that allows for the identification and quantification of atomic species in very small quantities. It utilizes a tunable laser source for resonant excitation and ionization of a particular element of interest and has some unique features: elemental selectivity, linear response over a large dynamic range and very high sensitivity. The analysis consist of three steps: (i) the solid sample is vaporized by laser ablation to form a plume containing neutral atoms, (ii) the neutral atoms of a specific atomic element in the plume are resonantly excited and ionized by another tunable laser, and finally (iii) the ions created are mass analyzed in a time-of-flight mass spectrometer. A TOF-RIMS mass spectrometer was developed at AMTEL for trace element analysis of Au, Pd, and Rh in minerals. The spectrometer was calibrated using homogeneous CANMET and NIST reference samples covering three orders of magnitude in concentration. Attained minimum detection limits (MDL=2cr of the background) are in the low ppb range.

Jan 1, 1999

By Oscar Perales Perez, Atsuo Kasuya, Kazuyuki Tohji, Yoshiaki Umetsu

"The removal of iron and various heavy-metal ions by their incorporation into stable ferrite-type precipitates at 25°C is a promising alternative to clean up large volumes of polluted aqueous effluents. Our research work investigated the conditions to produce magnetite and various M-bearing ferrites (where M: Zn, Cu, Co, Ni, Cd, etc.) directly from aqueous solutions at 25°C by simultaneous control of the oxidizing conditions and pH. The formation of the solids was followed by monit9ring the oxidation-reduction potential (ORP) and rate of proton release during the aerial oxidation of the suspensions at constant pH (contact stage). Only mildly oxidizing conditions, represented by ORP values between -110 mV and -150 mV and a moderate oxidation rate of Fe(II) species were conducive to well-crystallized ferrites at ambient temperature.' It was also found that increasing the Fe/M mole ratio in starting· solutions enhanced the stability ·of the M-bearing ferrites at ambient temperature. When the formation of the ferrite was incomplete, aging of the sludges in their mother liquors at 25°C promoted the crystallinity of the precipitates. The mentioned conditions ·favored the suitable progress of the ferrite-forming reaction involving the oxidation of Fe(II) entities, subsequent hydrolysis of produced Fe(III) species and dehydration of the intermediate:· Furthermore,· the ferrite formation at· low temperature permits the elimination of iron and co-existing heavy metal ions to sufficiently low concentration.In tum, the characterization of the precipitates evidenced their magnetic nature (room-temperature saturation magnetization above 60 emu/g) as well as the effective incorporation of target metal ions into the ferrite structure."

Jan 1, 2000

By Young-Sool Jin, Heung Nam Han, Hong Joon Kim, Jae Kon Lee

A mathematical model was developed considering non-symmetric cooling' and stress distribution in both thickness and width direction of strip on a run-out table of hot strip mill. In order to solve a transient heat transfer equation including the heat evolved from phase transformation, a finite element method coupled with thermodynamic and kinetic analyses was applied. The heat capacity of each phase and heat evolution due to phase transformation were obtained from the thermodynamic analysis of the Fe-C-Mn-Si system based on a sub lattice model. The phase transformation kinetics of the steels was derived by using an inverse additivity technique with continuous cooling experiments. Heat transfer coefficients of strips on the run-out table were, by applying an inverse method, determined from the actual mill data under various cooling conditions. As for the stress analysis, the density change of strip due to cooling and phase transformation, and the transformation superplasticity were considered. A 90nstitutive equation for the transformation superplasticity, which is related to the phase transformation kinetics and the internal stress due to the density change of strip, was applied. A finite element method was adopted to calculate the deformation behaviour of strip on a run-out table of hot strip mill. Using the models, the temperature-phase-deformation history and distribution of a strip on the run-outtable was calculated.

Jan 1, 2001

By H. Y. Sohn

"The nonferrous production industry has gone through a remarkable transformation in recent years in terms of developing and adopting new technologies. Technology innovations have largely been driven by the need for greatly improved environmental protection in addition to increased productivity. One of the most notable aspects of the new technologies is their ability to reduce the emission of sulfur and other pollutants to extremely low levels.The current industry trends towards more environmentally friendly technologies are bringing about additional benefits of developing more efficient, technically advanced, and continuous processes in closed reactor vessels. Key aspects of these modem trends include the use of increased oxygen enrichment in the process gas, better process control, reduced manpower requirements, and plant operations with more skilled personnel.Computer simulation and modeling of complex processes have become more reliable, realistic, and thus increasingly useful in metal production. Some of the notable examples are reviewed.Finally, the need and advantages for value-added production in the nonferrous industry are discussed.I. IntroductionMost recently commissioned technologies for nonferrous metals production have been developed largely in response to environmental concerns. One of the most remarkable improvements made by the nonferrous industry in the last decade has been the rapid increase in sulfur capture. Before the start of the last decade, 90% capture of sulfur was considered good. Since then, strict emission regulations have become the norm in advanced societies, although smelters in many parts of the world still operate with limited pollution control. Other emissions and discharges have also been substantially reduced, resulting in much improved working conditions and worker hygiene in addition to the overall environmental protection. The development of the more environmentally friendly technologies has accompanied other advantageous advances made in the nonferrous industry, i.e., the trend towards more gas-tight, continuous processes and larger plants. This has increased the competitive edge enjoyed by the industry in the industrial countries, offsetting the higher costs of labor and pollution abatement that they have to overcome in those countries. Experience has shown that clean technology often leads to a profitable business, because its adoption forces the concomitant advancement of related technologies in addition to the avoidance of penalties imposed by the public on pollution-prone industries. Needless to say, there are other driving forces for new technologies such as reduction of operating and capital costs, improved product quality, and energy considerations in terms of reduced consumption and utilization of readily available sources."

Jan 1, 2000

By John R. Turney

The success of the Mclaughlin acid pressure oxidatiun process has proved that a complex hydrometallurgical process can be an economically viable means of treating refractory gold ores. Homestake's Mclaughin acid pressure oxidation process was commissioned in August 1985 and ts currently operating at design tonnage of 3,000 tons per day. Mineralogical and process studies on the operating plant are discussed to show the improved understanding: of the process and its future applications. These studies are also compared with the initial process development work, thus illustrating the success of the initial scale up considerations.

Jan 1, 1989

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By Ernest D. Mast

Noranda's Altonorte custom smelter, located in the 2nd region of Chile, 20 kilometres southeast of the city of Antofagasta, started operations in 1993. Presently, 1150 tonnes per day of new feed are smelted with an 85% sulphur capture. An oxy-fuel reverberatory furnace produces a 48%-55% copper matte that is treated in 13 ft. x 36 ft. (3..96m x 10.97m) Peirce-Smith converters (two hot and one blowing). Up to thirty percent of the new concentrate is smelted via dry concentrate injection into the converters. This paper reviews the development of the concentrate drying and injection system, and oxygen enrichment at Altonorte from start-up in 1995 to the present time. The relationship between oxygen enrichment and concentrate injection is reviewed from a theoretical and practical standpoint. Concentrate injection has improved the smelter's productivity and added flexibility to the operations. Due to the relatively high matte grades and the subsequent short converting times, maintaining consistent operations was difficult at times and the smelter has gone through a learning curve. Plant operating results and experiences are presented on the impact of concentrate injection in relation to: feed treatment, blowing times, revert generation, slag quality and refractory wear.

Jan 1, 1999

By Tuula Mäkinen

One of the latest applications of the Outokumpu Flash Smelting Technology is the direct smelting ,of nickel concentrates to metallised low-iron nickel mattes. Compared to the conventional nickel smelting, the new DON process needs a lower number of smelting vessels resulting in considerable economic and environmental benefits. Fundamentals of smelting nickel concentrates in one stage to low-iron mattes are presented. Properties of nickel. smelting slags with an emphasis of the slag fluidity at high MgO-levels are also discussed. Conditions prevailing in DON mattes at high oxidation degrees are presented as well as their influence on the behaviour of such mattes in the settler and on tapping the furnace. Distributions of elements in the direct smelting are presented and compared with the conventional process. A further comparison is made with pilot-plant data and the industrial scale.

Jan 1, 1998

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"Drying (water removal) prior to smelting is always economically feasible. Unnecessary heating of vapour can thus be eliminated resulting in savings of5-15 MUSD every year.Thermodynamically removal of one ton of water out of copper concentrate at 100 °C (with 10 % moisture) requires approximately 3150 MJ/tH2o, consisting of heating of the water (377 MJ), heating of the concentrate (509 MJ) and water evaporation (2260 MJ). This is quite independent of the selected drying technology. In reality some more heat is needed as higher temperature is practiced to enhance the drying performance and to reduce the equipment size.Major nominator in drying energy efficiency is amount of gases, which depends greatly on the drying technology. Dryers based on direct heating with fossil fuels have high gas flow rates, and thus they require additional energy of about 1400-1600 MJ/tH2o, compared to indirect modemsteam drying at 250-400 MJ/tH2o.Significant benefits in energy consumption (900-1300 MJ/tH2o) with additional potential for a bonus profit of 2-4 MUSD/y year, together with full elimination of some 40 000 tpy CO2 per mid-size dryer is available by selecting sustainable, energy efficient steam drying.IntroductionRemoval of water from the concentrate is very energy intensive thus having a significant environmental impact. However, drying prior to smelting is always economically feasible and very often viable also from the perspective of process operations. This environmental impact of drying can, however, be decreased or even fully eliminated with proper selection of the drying technology.Energy incorporated in drying consists always of a number of phases like liquid (water), solids (concentrate) and gases (water vapour, purging I dilution air, combustion gases). Each phase is heated to a specific temperature during the drying process.Heating of water, heating of the concentrate and water evaporation consumes more or less the same amount of energy despite of the drying technology (3150 MJ per ton of water). In conventional drying this amount of energy is achieved by combustion of fossil fuels wirg subsequent CO2 emission. Alternatively, chemical energy derived from sulphide smelting can be utilized in a form of steam thus generating zero emission ofCO2, in modem steam drying."

Jan 1, 2012

By Z. Yang, R. W. Smith, Jr. Wharton

"Microorganisms have the ability to remarkably adsorb and/or absorb heavy metal ions. Hence they are being studied widely as a means of removing metal ions from aqueous solutions both in order to clean up toxic streams and to recover valuable metals from these and other streams. It is often difficult to harvest organisms such as bacteria and unicellular algae since they are usually too small to be readily screened out. Froth flotation may prove to be a feasible method to harvest such organisms subsequent to the ad/absortion of the metal Ions. The present paper discusses the surface/electrokinetic properties of microorganisms and the modifier-collect conditions under which they should float. The zeta potential of the green alga Chlorella vulgaris was measured in the presence of AI(III) and Pb(II) ions and in the presence of dodecylammonium chloride and sodium dodecylsulfate. Present and past data suggest that the organisms should behave similarly to other finely divided, charged (polar) solids with their behavior sometimes modified by the non-polar surface regions present.IntroductionThe overall field of bioengineering is growing at a remarkably accelerating rate. Hydrometallurgy and mineral processing are included among those disciplines where there has been actual or proposed commercial use of bioorganisms. Further, the actual or proposed use includes bacterial enhancement of leaching of a number of different types of ores (1-5), modification of the flotation or oil agglomeration separation of minerals by bacteria (6,7) and microorganism (algae, bacteria or fungi) concentration of metal ions present in effluent or other mineral processing or hydrometallurgy aqueous streams (8-23)."

Jan 1, 1988

By Natasa Mitevska

The statistical analysis of the slag composition influence on copper losses to discard slag in the reverberatory furnaces No.1 and No.2 in the RTB BOR, Copper Smelter and Refinery (Yugoslavia) is presented in this paper. The model for the slag basicity calculation is determined, and connected to the copper distribution coefficients between the matte and slag phase. The influence of all components on the slag structure is also illustrated.

Jan 1, 2003

By Helmut Antrekowitsch

Nowadays nearly the half of the world zinc production is used for galvanizing. After their life span most of the galvanized products return as scrap to the steel mill. During the steel process the zinc is collected in the flue dust It is astonishing to notice that between 40 and 50 % of the zinc produced is brought into the steel processing cycle by the coated scrap while only 3 to 5 % of the zinc production can be covered by the recycling of the zinc-bearing steel mill dusts. Responsible for this worse ratio is the fact that the established recycling technologies suffer from high energy consumption, low zinc yields, halogen problems and hardly any iron recovery. A development of new or an optimization of current recycling procedures for the dusts is unalterable because of increasing zinc amounts in these residues and the rising costs for the disposal. Different pyrometallurgical recycling technologies are tested in rotary kilns and vertical retorts at the Department of Nonferrous Metallurgy, University of Leoben, Austria. Various reducing agents from carbon monoxide to hydrogen and combinations are used. The results should make it possible to draw conclusions that allow an economical and ecological judgement of the different varieties. The goal is to support the affected industry to increase the low recycling rate and prevent a loss of high zinc values in the steel industry filter dusts.

Jan 1, 2003

By Alicia E. Ares

316 L Stainless Steel samples were solidified directionally under conditions which produced the columnar to equiaxed transition. The position of the transition was located in each sample and the distance from the bottom of the ingot was measured. During solidification the distribution of temperatures were measured by means of thermocouples located strategically. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solidus fronts. Comparing the location of the transition and the values of these parameters it was found that the temperature gradient reaches negative values of as low as -13.44 "C/cm, and velocities of the fronts of around 0.1 cm/s. Also, a supercooling of 5.81°C were measured which was associated with the supercooling for the nucleation and growth of the equiaxed grains ahead of the columnar front. In addition the primary and secondary dendritic spacing was measured in both regions. The spacing was compared with the predictions from available models. The results are presented and discussed in the frame of the results obtained for other alloys

Jan 1, 2002

By Donald R. Sadoway

"Molten salt electrolysis is a proven technology for the extraction of metals -- all· the world's primary aluminum is produced in this manner. The unique properties of molten salts also make them excellent media in which to treat a variety of forms of waste. Of special note in this regard is electrolysis in molten oxides, a concept put forward by the author, initially as a ""clean technology"" for producing primary metal. However, in the context of waste treatment, electrolysis in molten oxides is a process offering the prospect of changing the-valence of dissolved heavy metals while making pure oxygen gas as the main by-product. Laboratory tests conducted at a temperature of 1550°C on chromate sludge dissolved in an melt composed of Al2O3, SiO2; CaO, and MgO have confirmed electrochemical production of oxygen on a carbon-free anode. IntroductionMolten salt electrolysis is the electrolytic decomposition of a compound dissolved in an ionic melt. The prime example of this process can be found in the production of aluminum. The compound, alumina (Al2O3)' derived from the mineral bauxite, is dissolved in an ionic melt comprising a multicomponent solution of cryolite (Na3AlF6)' aluminum fluoride (AlF3)' and calcium fluoride (CaF2,). The products of electrolysis are molten aluminum and carbon dioxide, the latter due to the attendant consumption of the carbon anode. Primary aluminum is produced in a reactor known as the Hall cell.' Alternatively, the compound undergoing electrolytic decomposition can be derived from waste. Processing in molten salts, with their capacity to dissolve materials to very high concentrations compared to those attainable in aqueous solutions, can be rather advantageous. High solubilities lead to high limiting current densities, and this, in tum, results in high productivities: For a primer on molten salt electrolysis and a review of the basic literature in the field of molten salts the reader is directed to an earlier publication of the author (1)."

Jan 1, 1996

By E G. Prado

We have confirmed on bench scale the removal of chlorides and alkalies (+95%) and over 2/3 of the zinc, lead and cadmium from EAF dusts. This has been achieved with arrononium acetate solutions alone, or with combinations of water wash, amonia-ammonium carbonate and ammonium acetate solutions. Also confirmed are the process routes for the recovery of the aforementioned elements into marketable products. The technology involves the complete recycling of the reagents. The FAF residue is returned to the electric furnace without risk of impurities buildup. Commercial scale testing with the recycled dust was satisfactory, including quality of the slag and its behavior during the melting stage. A cursory feasibility evaluation is presented.

Jan 1, 1994

By J. D. Scott

The counter-current jarosite acid wash circuit presently in operation in the zinc plant produces a combined jarosite plus Pb/Ag residue which is discarded. Extensive pilot-scale testwork, and some past in-plant operational experience, has shown that the zinc plant can be easily reconfigured to produce two residues during periods of high silver feeds and/or prices. Plant.optimized circuit configurations are available for silver recovery to a Pb/Ag residue and are in use for the prevention of Pb/Ag-jarosite formation in both the neutral and high-acid leaching circuits. Silver in the zinc plant undergoes several changes in state as it proceeds through these circuits. The roaster calcine is ~3:1 silver sulfate: silver metal, with metallic silver mainly as micro-Inclusions In an aluminosilicate phase. In neutral leach residue, the majority is as silver sulfide or Pb/Ag/Zn-sulfide coatings on unroasted sphalerite grains, with minor Pb/Ag-jarosite and some residual metallic silver in unreacted alumina-silicate grains. In high-acid leach residue, silver occurs as Se-rich silver sulfide particles in sulfur/jarosite ball aggregates, as silver sulfate impregnations in silica-gel masses and in solid solution in Pb/K/Zn~jarosite. Silver concentrations in solution range from 20 to 60 ppb.

Jan 1, 1990

By Pragna N. H. Bhakta

The minerals industry is under political and economic pressure to reduce its processing wastes and minimize their impact on the environment: Recycling is one of the means by which the minerals Industry can reduce the quantities of effluents and residues that are discharged to the environment. The wise use of available resources is not only an environmental necessity but also an economic benefit as natural mineral resources are depleted and/or become more complex. The purpose of this paper is to review the technical and regulatory issues that will help shape the future of minerals recycling over the next ten years. Research and development to address technical issues will be discussed with emphasis on the Bureau of Mines recycling research program.

Jan 1, 1992

By Donald R. Sadoway

Molten salt electrolysis is a proven technology for the extraction of metals -- all the world's primary aluminum is produced in this manner. The unique properties of molten salts, also make them excellent media in which to treat a variety of forms of waste. Of special .note in this regard is electrolysis in molten oxides, a .concept put forward by. the author, initially as a ."clean technology" for producing primary metal. However, in the context of waste treatment, electroly-sis in molten oxides is a process offering the prospect of changing the. valence of dissolved heavy metals while making pure oxygen gas as the main by-product .Laboratory tests conducted at a temperature of 1550°C on chromate sludge dissolved in an melt composed of Al2O3 and MgO have confirmed electrochemical production of oxygen on a carbon-free anode.

Jan 1, 1996

By Ronald Erdmann

Today the BOF filter dusts and sludges are mainly dumped due to their zinc contents. By typically ranging from 2 to 5 % they prevent the filter dusts and sludges from beeing recycled via the blast furnace route. Based on the different discharge kinetics of Iron and zinc during the main blowing period In a bottom stirred BOF a simple and efficient system for recovery allow zinc fractions has been developed. The obtained material Is suitable for recycling without nsc of shell formation In the blast furnace. Different subsequent development steps have been performed. By starling with a very simple lime dependent model the sludge from the BOF off gas cleaning system was collected in two different sludge channel systems. This model based an the fact that most of the scrap based zinc Is discharged from the melt within the first eight to ten minutes of the BOF process. To Improve the system a spectroscope zinc sensor was Installed at the hot section of the off gas cleaning system to get more reliable informations on the actual zinc concentation of the BOF dust. By use of the system up to 50 % of the BOF sludge can be recycled.

Jan 1, 1995

By Alan James Parker

Chalcopyrite can be converted to pure copper by the following five steps. An exothermic sulfation roast of chalcopyrite; leaching of cupric sulfate from the calcine with dilute acid; precipitation of Chevreul's salt and or other copper sulfites with ammonium sulfite or precipitation of crude copper by autoclaving ammonium sulfite and cupric sulfate at 150°C; dissolution of Chevreul's salt, or the crude copper, as cuprous sulfate, using acidic cupric sulfate in an acetonitrile-water solution as oxidant; precipitation of pure copper by thermal disproportionation of the cuprous sulfate solution. Acetonitrile and acidic cupric sulfate solution recycle. Advantages over conventional processes include lower cost, lower energy consumption as waste heat, sulfur removal as ammonium sulfate or gypsum, rather than as sulfur dioxide and rapid throughput. The net reaction is: 2 CuFeS2 + 4H20 + 15/2 02 + 8 NH3?2Cu + 4 (NR4)2 SO4 + Fe2O3

Jan 1, 1976