Search Documents

By James W. Evans, Brian R. Wildey

"Carbon has been the principal reducing agent in producing metals for centuries. Carbon is an inexpensive reducing agent, but also an effective one, as any undergraduate who knows her Ellingham diagrams is aware. Even in the production of aluminum, an electrolytic process, carbon consumed at the anodes serves to reduce the voltage of the Hall-Héroult cell. The interest in reducing the amount of anthropogenic CO2 has led to this examination of whether a switch to hydrogen as a major reductant is feasible and economic. The main source of hydrogen is natural gas and its production entails the generation of CO2; however, that CO2 is more easily captured than, say, the CO2 leaving an iron blast furnace. Calculations and speculations lead to conclusions about whether there is significant benefit to be obtained from such a radical change in our way of producing metals and the approximate cost of such change.IntroductionThe 1991 paper by Forrest and Szekely1 was one of the first to examine the impact of CO2 emissions from the primary metals industries on global climate change. These authors compared data from 1968 and 1985 and reported a drop in carbon emissions from 115.8 million tons to 65.6Mt over this period, the latter figure representing approximately 1% of the world’s greenhouse gas emissions. Much of this reduction was due to a drop in steel output (with carbon emissions increasing within the aluminum and copper industries in this period) but some were due to technological changes such as increased use of continuous casting. A more recent paper on CO2 emissions, focused on the steel industry in Japan, is that of Ariyama and Sato2. These authors report CO2 emissions of 182.4Mt from the Japanese steel, industry in 2003, down from 194.8Mt in 1990. The former represents 14% of the GHG emissions for Japan in 2003. Much of this emission is from ironmaking and the authors break these emissions down into"

Jan 1, 2008

By J. H. Puffer

The copper mineralization of the Mesozoic Passaic Formation of New Jersey is typical of copper deposits in eastern North American Mesozoic sediments. Most such deposits are located at the base of the first of several basalt flows that are interbedded with continental, red-bed sediments. The copper mineralization is similar in most respects to that of the Keweenawan Basalts of the Lake Superior area. The first basaltic flow units of the eastern North American Mesozoic basins, and the Keweenawan Basalts, are continental quartz tholeiites of similar chemical composition and copper contents. The copper minerals and associated zeolite facies metamorphic mineral assemblages of these two rock units are also approximately the same. Stoiber and Davidson (1959) suggested that Keweenawan copper was mobilized and concentrated during metamorphism. The evidence pertaining to the Mesozoic copper deposits of New Jersey is consistent with such an interpretation and also with DeVore's (1955) suggestion that ore fluids commonly arise as a result of the mobility of metals under metamorphic conditions. There is additional evidence that final metamorphic concentration of Mesozoic copper was preceded by an initial stage of hydrothermal precipitation related to fluids emitted by basaltic magma.

Jan 1, 1987

By David S. Holmes

An overview of existing biological technologies for the recovery of copper and uranium is presented. Engineering and biological challenges and opportunities in these areas. are discussed. New opportunities for the biooxidation of refractory gold ore are described. Techniques for the development of new strains of microorganisms. for commercial metal recovery applications are discussed with special reference to the genetic manipulation for bacterial strain improvement.

Jan 1, 1991

Two pilot-plant investigations were conducted in which strong-base resins were compared with activated carbon for the extraction of gold cyanide from leached pulp from the Golden Jubilee Mine. The results show that gold can be recovered with carbon, but that the extraction efficiency is poor, probably because high concentrations of humic and fulvic acids are. present m the pulp. .However the extraction of gold cyamde from this material with strong-base resins JS very effo:1ent, and the overall efficiency of extraction is better with resin than with carbon, even when the concentration of resin is one-third that of carbon, and the flowrate of resin is one-third that of carbon. The results of the pilot-plant campaign reported in this paper led to the conversion of the Golden Jubilee plant from carbon-in-pulp to resin-in-pulp in February 1988.

Jan 1, 1989

By David T. Hobbs

Large quantities of highly alkaline, radioactive, liquid wastes are stored in underground tanks throughout the Department of Energy complex. These wastes will be pretreated to separate radionuclides and the remaining decontaminated liquid wastes incorporated into solid waste forms for permanent disposal. Significant savings in disposal costs could result by recovering .the sodium as sodium hydroxide for reuse or disposal as nonradioactive waste. Recent testing demonstrated an electrochemical separation process for the recovery of sodium hydroxide from alkaline waste solutions; The separation process uses ion-selective membranes to separate sodium from the bulk of the waste constituents under an applied electrical field. The sodium is recovered as a 10-15 wt % solution of sodium hydroxide. Results of bench-sc3Ie and pilot-scale tests with simulated and radioactive waste solutions are presented.

Jan 1, 1999

By Steven R. Izatt

IBC Advanced Technologies, Inc. (IBC) has developed a mercury selective product, which can be used by sulfuric acid producers as either a polisher, or as the primary technology for mercury removal from sulfuric acid. The Molecular Recognition Technology (MRT) separations material selectively binds Hg2+, and to a lesser extent Hg+, out of concentrated sulfuric acid. Mercury output levels of less than 0.1 ppm can be attained by the MRT system. Pilot plant tests have been successfully conducted at base metal smelting operations. A large-scale commercial plant is due for commissioning in 2003. Results from these projects will be discussed.

Jan 1, 2003

By Stephen W. Paff

The EPA has estimated that there are over 3,000 sites across the United States contaminated with lead. Techniques to remediate these sites include standard stabilization/disposal technologies, reclamation of lead using secondary lead smelters, soil washing, and biological removal technologies. In this paper, the current technologies used for lead remediation will be reviewed. Factors affecting the use of each technology, such as range of applicable concentrations, soil types, interferences from other contaminants, economics, and current technology status will be assessed. The paper will also focus on the results of a recent study completed by the Center for Hazardous Materials Research (CHMR), in conjunction with a major lead smelter, which demonstrates that secondary lead smelters may be used economically to reclaim lead from a wide range of lead-containing materials frequently found at Superfund sites. Such materials include battery case materials, lead dross, and debris containing between 3 and 70% lead. The results of development work completed by CHMR on the Acid Extraction Treatment System (AETS), which has been demonstrated to extract Lead from soils containing up to 30,000 mg/kg lead, will also be presented. The use of these technologies will be compared with other options for the remediation of sites.

Jan 1, 1994

By P. N. Anyalebechi

The effects of a cross-hatched grooved mold surface topography, casting speed, and superheat on the morphology of solidifying shells of aluminum alloy 3003 have been characterized by a series of immersion tests. The cross-hatched grooves were 0.232 mm deep with wavelength or spacing between 1 mm and 15 mm. The shells solidified at casting speed of less than 10 mm/s on the 1 mm spaced cross-hatched grooved mold surface were fairly uniform with little or no localized variations in thickness. However, the propensity for non-uniform shell growth morphology was exacerbated by an increase in casting speed, melt superheat, and the wavelength of the cross-hatched grooves. This is provisionally attributed to their effects on interfacial heat transfer and wetting of the mold surface by the molten metal.

Jan 1, 2008

By Yoichi Takeda

The CaO-FeO,-Cu20 slag has been practically applied to continuous converting of copper, and also has potential for refining of copper. Liquidus lines of the slag system and phase stability diagram for the liquid slag and the existing solid compounds under copper saturation are presented. Liquidus composition was determined by chemical analysis of slag sample saturated primary solid. The temperatures of invariant equilibria were investigated by thermal analyses. Oxygen potentials on the liquidus lines, the univariant and invariant equilibria were estimated from the relation slag composition and oxygen potential that relation was confirmed in separate experiments.

Jan 1, 2003

By W. J. Mitchell

During the months of April and May 1992, the Phelps Dodge Hidalgo smelter underwent a major turnaround. This was the third such turnaround in the life of the facility which was commissioned in 1976. During the third furnace campaign, the smelter processed 5.2 million tons of concentrate producing 2.6 billion pounds of anode copper over a 7.5 year period. The critical path on the fifty-nine (59) day turnaround schedule was the reconstruction of the Outokumpo flash furnace which integrated some modifications with standard rebuild practices. Modifications included incorporation of horizontal cooling jackets throughout the furnace settler as well as the installation of castable refractory in the reaction and uptake shafts.

Jan 1, 1993

By Neale R. Neelameggham

"Most chemical process plants and metallurgical production facilities have some sort of cogeneration to minimize process energy costs. Use of Alternative Energy Production from sun and wind power with storage can become an integral part of a process plant utility. This will facilitate reduced fossil fuel usage and help minimize thermal emissions. This will be similar to Pollution Control equipment, which have become an essential part of process plants in the past four decades. Conceptual flow sheets of such Process Utility schemes are presented.IntroductionPower is supplied to industries, commercial and residential users. Over the past decade, Electric Utility companies have made major inroads, in introducing alternative energy resources in an attempt to somewhat reduce fossil fuel use in power generation. Now, on a much larger scale than in the early 1980s, residential users, motivated by government provided tax credits, have started installing alternative energy generators such as roof top wind mills or roof-top photovoltaic generators. This will minimize future energy costs, help control thermal emissions etc. This alternative power generation is typically connected to the existing power grid with two way power metering. However, the use of alternative energy generation has not been seen at large industrial sites yet.Paul Scherer Institute, Switzerland and the NREL laboratories in Colorado, are two of the several institutes which have been developing how solar thermal power can be used to supply the endothermic input energy in chemical and metallurgical processes. The theme of this present symposium addresses the above as well as the energy storage needs for such events to become continuous. This paper emphasizes the concept of how alternate energy can be used in the production of materials on a generic sense wherever there is a need for input energy – beyond endothermic process energy - while addressing how to reduce the thermal and carbon emissions.The alternative energy generation using wind or solar source is discontinuous due to the nature of the energy source. They are not only discontinuous but also variable. This necessitates storage of generated power for close to continuous use with variable loads. C Smith, et al pointed out in 2006, that 'the electric power industry has taken notice of the expansion of wind and its potential' in a summary article on integrating wind generation into utility systems.1 In 2009, the 1000 MW wind generation project in Texas had to be postponed to 2013 for lack of transmission.2 There are only a few large MW solar generation units in the US; the projects being slow mainly from lack of adequate storage and redistribution."

Jan 1, 2010

By Tor Lindstad

Specific C02-emissions are given for the production of silicon-metal, ferrosilicon, ferromanganese and silicomanganese. Emissions taken into account come from reduction materials, from coke production and generation of electric energy. C02-emissions can be abated by direct and by indirect methods. A direct method is to replace fossil carbon as reduction material wholly or partially by endogenous carbon (biocarbon, charcoal). Another possibility is to produce metals by electrolysis instead of the present electric smelting furnace. Indirectly CO2-emissions can be reduced by energy recovery, thus saving coal, oil or natural gas for heat generation. Some reduction in global C02-emissions can be obtained by giving credit for the use of silica dust partially replacing cement in concrete. In addition to give an overview of possible methods, costs will be discussed.

Jan 1, 1999

By Ljiljana Solujic

The need for the removal of mercury from the precious metals extraction circuits may be influenced by process, environmental, as well as by occupational hazard reasons. In these circuits mercury is mainly present as cyanide complexes. The effectiveness of any stabilization method will be influenced by the high thermodynamic stability mercury-cyano species exhibit in an aqueous solution. In this study, we have investigated the utility of the trisodium salt of trimmercapto-s-triazine (TMT) for precipitation of mercury from the corresponding cyano-complexes. The influence of pH molar ratio of TMT to Hg, coagulant and flocculant additions, excess of free cyanide, as well as the presence of other metal-cyano species on the effectiveness of mercury precipitation were investigated in detail. Also, a "teal world" precious metals mill effluent initially containing ~7 ug/mL (ppm) of Hg was treated and A was found that greater than 99.8% of the mercury was removed from the solution as am insoluble Hg/TMT complex.

Jan 1, 1996

By Run Huang, Xuewei Lv, Songli Liu, Chenguang Bai

"Titanium alloy was prepared from titania-bearing blast furnace slag (Ti-BF slag) by aluminothermic process in an induction furnace. The effects of aluminum amount on the titanium silicon yield and titanium recovery ratio were studied. The phase transformation and chemical composition of the prepared alloy were investigated by X-ray diffractometry (XRD) and X-ray fluorescence (XRF) respectively. It was found that the mass fraction of silicon and aluminum increased with increasing the aluminum amount, however, the mass fraction of titanium increased first and then decreased with increasing the aluminum amount. Furthermore, both the titanium alloy yield and titanium recovery ratio increased with the increase of aluminum amount. The main phases of the alloy were TixSiy and AlTi3. The titanium alloy samples prepared in various conditions had a composition (wt.%): 38–50% Ti, 29-34% Si, 4-11 Al%, 1.6-2.2 Mn%.IntroductionPanzhihua and Xichang regions in the southwest of China are rich in vanadium-titanium magnetite containing iron, vanadium, titanium and gangue. According to the characteristics of the resource, iron and vanadium are successfully recovered with a blast furnace process and a converter process. However, most content of titanium are entered in the blast furnace slag with TiO2 22% -26% and metallic Fe 2%–6% called Ti-BF slag. Due to the dispersed distribution of Ti in various fine grained mineral phases with a complex combination between Ca, Al and Si, it is difficult to recover the Ti components[1]. This slag is generated at a current rate of 3.6 million tons per year, which adds to the existing 70 million tons of slag produced so far[2]. The slag has had to be piled as large as the mountains, which not only waste of resources but also cause a pollution of the environment. Therefore, the study of integrated utilizing Ti-BF slag has become very significant."

Jan 1, 2012

By Kevin L. Gering

A detection method and apparatus have been developed to perform real-time measurement of aqueous free cyanide, C-. A laboratory prototype can measure cyanide ranging from 5 micrograms ,per liter to 100 milligrams per ?liter for analysis times as short as 2 minutes per measurement. Sample size per measurement is typically only a few mI, thus? minimizing the waste volume produced from spent samples. The basis for this detection device is a quantifiable, stable affinity between the electrode material and free cyanide in the sample; The electrode exhibits piezoelectric behavior, allowing it to be used as a microbalance. This technology 'has experienced two generations of laboratory prototypes, and has been thoroughly tested to determine the operational sensitivity toward process variables such as pH, competing reactions, etc. The speed and ,accuracy of this method make it superior to conventional wet chemistry methods used for quantifying cyanide levels in water. A device based on this technology could be useful in areas involving process monitoring and environmental compliance, .particularly in the cyanide-based leach mining industry. Interest for this detector has been shown by the gold mining industry and others. Patent application is in progress.

Jan 1, 1998

By Michael J. Nicol

Growing environmental and occupational safety concerns about the use of cyanide in gold processing has increased the interest in more acceptable alternatives. The most likely of these is thiosulfate. However, the thiosulfate process lacks a proven in-pulp method of recovering the dissolved gold, because activated carbon is not effective for the absorption of the gold thiosulfate complex .. Anion exchange resins do offer a possible route for in-pulp recovery. This paper describes work aimed at the evaluation of the effectiveness of commercially available anion exchange resins for the recovery of gold from thiosulfate leach liquors? and pulps. It has been found that strong-base resins are superior to weak-base resins in that they have a larger capacity, which assists in reducing the competition from other anions within a leach solution. Further studies with a selected commercial strong-base resin have shown that competing polythionateanions (particularly tri-and tetrathionate). Lower the maximum possible gold loading but that gold is selectively recovered over other base metal anions in solution. Kinetic experiments found that while? competilig anibns did not affect the initial rate? of gold loading it was important to minimise the contact time of the resin in solution so to prevent displacement of loaded gold by competing anions over longer times. A small-scale resin-in-pulp plant investigation showed gold can be recovered from a leach pulp by a strong-base resin to yield gold loadings of 3000 mg/L, barren pulp containing less than 0.05 mg/L of dissolved gold and. copper loadings of 500 mg/L. Loaded copper was displaced gold and at a loading of 2000 mg/L gold the copper loading was minimal «500 mg/L). The resin was found to recover gold adsorbed on the solids that would, otherwise have. reported to tails if a solid/liquid separation method were used. A patented two-step elution process in which copper and then gold are separately eluted from the resin is also discussed.

Jan 1, 1998

By A. E. M. Warner

In co Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003

By George P. Demopoulos

In this paper the production and stability of crystalline scorodite (FeAsO4·2H2O) is discussed both on the basis of previously published work as well as recent work performed in our laboratory. The production of scorodite, especially from arsenic-rich and iron-deficient sulphate solutions offers a number of operational advantages such as high arsenic content, stoichiometriciron demand, and excellent dewatering characteristics. In addition to hydrothermal production of scorodite the work done over the last 10 years in our laboratory has determined that it is feasible to produce scorodite by step-wise lime neutralization at 90°C. The atmospheric scorodite possesses the same structural and solubility characteristics with the hydrothermally produced scorodite. Long term equilibration tests (up to 66 weeks) in the pH range 5 to 9 and temperatures from 22 °C to 75 °C revealed scorodite to undergo slow incongruent dissolutionyielding a highly metastable nano-sized 2-line ferrihydrite phase. The equilibrium arsenic concentration with this phase was 0.35, 0.96 and 5.87 mg/L at pH 5, 6, and 7 respectively at 22°C. In the presence of gypsum slightly lower concentrations were measured, this being more pronounced at pH>7. It was tentatively deduced that a Fe-Ca-AsO4 association (in the form of a phase resembling the mineral yukonite) contributes to the lowering of As concentration. Finally thermodynamic calculations determined that scorodite is stable in the presence of ferrihydriteunder oxic conditions up to pH 6.75 at 22 °C or higher pH at lower temperature and gypsum-saturated solutions. Keywords: Scorodite, Crystallization, Arsenic, Solubility, Stability, Precipitation, Disposal, Extraction, Processing, Metals, and Environment.

Jan 1, 2005

By T. Shi, Q. Yuan, S. P. Vanka, B. G. Thomas

"The quality of continuous cast steel is greatly affected by fluid flow in the mold region, especially involving transient phenomena. Mathematical models are being applied to investigate many different aspects of these phenomena, but their accuracy must be validated before they can be applied with confidence. As part of a long-term effort to develop and apply comprehensive models of the continuous casting process, this work evaluates the relative accuracy of models of three different fluid flow phenomena in continuous casting through comparison with measurements.Firstly, transient flow simulations of velocities in the mold region are compared with digital particle image velocimetry (PIV) measurements in a single phase water model. Large-eddy simulations (LES) are found to reasonably match the flow measurements, including transient flow variations, except at long time scales, which could not be modeled owing to the excessive computation costs. The standard K-e model produced very good agreement with time-averaged velocities for relatively little computation time, although it is inaccurate at predicting the transient variations. Secondly, particle trajectory calculations are compared with water model measurements to study the distribution and flotation removal of inclusion particles. The LES model was able to match the measurements both qualitatively and quantitatively. Thirdly, steady, multi phase flow computations are compared with flow patterns observed in both a water model and an operating steel caster with argon gas injection. For the same conditions, the water model and steel caster produced very different flow behavior. The computational model was able to match the measured flow patterns in both cases.This work suggests that computational flow modeling has the potential to match real processes as well or better than water models, especially when complex related phenomena such as particle motion and multiphase flow are involved. Much work is still needed to further improve the models and to apply them in parametric studies."

Jan 1, 2001

By A. Vahed

The Goro Nickel Project is situated in the Southern Province of New Caledonia. Inco Limited and Goro Nickel S.A. have developed a process that features the use of pyrohydrolysis to produce nickel oxide. The process treats a blend of laterites by Pressure Acid Leaching followed by solvent extraction of nickel and cobalt using Cyanex 301®. Purified nickel chloride solution is converted to high purity NiO product and 6M hydrochloric acid, which is recycled back to the SX circuit. In co-operation with Andritz AG, spray roaster and fluid-bed pyrohydrolysis technologies were examined for this purpose. Tests were conducted at the Andritz AG pilot plant in Vienna, Austria, and at Goro in larger scale installations. The latter served to establish process engineering design parameters for scale-up. Several process variables were investigated in both technologies and the off-gas characteristics were established. Fluid-bed pyrohydrolysis was selected for the Goro commercial plant, primarily because it produced a granular nickel oxide. The main focus of this paper is to outline the results obtained in pilot plant studies of liquid fueled fluid bed pyrohydrolysis for the Goro Project. Keywords: lnco Goro Nickel, Fluid Bed Pyrohydrolysis, Pilot Plant Tests

Jan 1, 2004