Search Documents

By Sugui Tian

By means of the T6 treatment, the measurement of creep curves and microstructure observation, the influence of T6 heat treatment on the microstructure and creep properties of Ti-6Al-4V alloy is investigated. Results show that the microstructure of the forged alloy consists of the banded-like a phase and networks b phase. After sub-temperture T6 treated, the microstructure of alloy consist of the block a phase and ?networks basket? structure. Under the conditions of the applied stress of 575 MPa at 4000C, the forged alloy displays a lower creep lifetimes, after T6 treated the creep lifetimes of the alloy is enhanced to 548 h from 66 h, which is attributed to the formation of the network basket structure in which the needle-like phase are dispersedly distributed. As creep goes on, the denser dislocations in the a phase are concentrated to occur the dynamic recrystallization for refining grain. which is a main reason of the alloy displaying a better creep lifetimes and plasticity. Thereinto, the creep mechanism of the forged alloy is thought to be the slip of the straight <a> and <a+c> dislocation are activated on the prismatic planes and pyramidal planes, while the creep mechanism of T6 treated alloy is that wave-like <a+c> dislocations are activated on the pyramidal planes.

Jan 1, 2009

By Florian Kongoli

Slags and fluxes are important interchangeable dimensions of pyrometallurgical processes. They can increase the efficiency of the smelting, converting and refining processes and improve the quality of the final products. A good slag should have appropriate physicochemical properties such as low liquidus temperature, optimal viscosity, maximum ability to attract undesirable elements, minimum potential of attracting valuable elements, etc .. A good flux, on the other hand, when properly used, can considerably improve the physicochemical properties of the slag since by modifying its chemical composition it could decrease the liquidus temperature, improve viscosity etc.. Consequently, the choice of a good slag and the corresponding fluxing strategies has become indispensable in most of industrial processes. However, the properties of multicomponent slags as well as the effect of several fluxes are known only empirically and confusion exists in the literature and in the industrial practice. In today&apos;s reality of frequent changes in the composition of raw materials and that of the fluxes themselves, in the existing or new developing technologies, the quantification of the thermophysicochemical properties of multicomponent slags and the effect of fluxes becomes indispensable. This paper reviews some of the work carried out by the author&apos;s group during the last ten years on the quantification of the thermophysicochemical properties of multicomponent slags and on the effect of fluxes in several smelting and converting processes in close relation to their individual characteristics. Several examples have been given in order to demonstrate the fact that when taken outside the context some fluxes can become in fact anti-fluxes.

Jan 1, 2003

By R. S. Celmer

The distributions of cobalt, molybdenum, copper, and selenium between nickel matte and silica-saturated iron silicate slag have been determined in the region of the metallic saturation boundary, at 1523 K. Results are given as a function of the composition of the coexisting Fe-Ni alloy and the activity of iron in the system. Under strongly reducing conditions, these minor elements display a marked preferential accumulation in the sulphide phase. It is shown that the dissolution of cobalt and molybdenum in slag follows an oxidative mechanism, and distribution equilibria are correlated with the oxygen potential. From these data, the thermodynamic properties of cobalt in nickel matte are computed. Further, comparisons of minor element partitions are made between the nickel and copper matte smelting cases under metal saturation conditions.

Jan 1, 1988

By Larry Twidwell, Ed Rosenberg, Courtney Young, Sean Dudley, William Gleason, Maureen Chorney

Experimental and industrially produced polystyrene and silica resins are tested for recovery capabilities of Rare Earth Elements (REE). Testing regimes being used are typical of resin analysis. Inductively Coupled Plasma-AES results indicate that preferential separation and recovery is possible in the adjusted pH range of2 to 10, solution conditions, and resin type. Testing conditions are resulting in structure modification of the composite resin as indicated by X-Ray Diffraction, Differential Scanning Calorimetry, Scanning Electron Microscopy, Mercury Porisometry, and density analysis. Resin modification indicates both surface and internal structure alteration outside of reported standard behavior of resins. Structural changes have ramification for both Rare Earth Recovery RER and traditional resin operations. Analysis shows that the resin uptake of REE can be manipulated for concentration. Further analysis with SEM work indicates that widespread surface and interior modification is taking place as resins load with REE. This modification is leading to pore rupture and particle breakage. Further investigation is being performed to determine the mode of breakage.

Jan 1, 2015

By Jiann-Yang Hwang

A study on microwave assisted chalcocite leaching was carried out with a microwave hydrothermal reactor. The leaching was conducted with thick mineral slurries (50-100 g/l). The leaching media is a mixed solution of CuCL2 and NaCL The investigation included the effect of leaching temperature, quantities of the minerals per unit slurry volume as well as the initial concentration of cupric ions were investigated. The results were discussed and compared with that using conventional leaching method.

Jan 1, 2003

By Sayan Sarkar

HAMR (Hydrogen Assisted Magnesiothermic Reduction) process is a promising alternative route of titanium production, which is convenient due to reduction at relatively lower temperatures below 750 °C and usage of cost-efficient TiO2 as the starting material. A crucial step involved in this process requires the Mg reduction of TiO2 subjected to H2 atmosphere which produces porous TiH2 along with residual magnesium impurities. Before the final heat treatment and deoxygenation steps for consolidation of the Ti powder, leaching plays a significant role in the removal of Mg impurities. In this report, we present a systematic study on the role of acid concentration (HCl), temperature and the kinetics of MgO dissolution. In addition, we also report the controlling mechanism during kinetics of MgO dissolution in acid. This parametric study will provide a platform to ensure very low Mg content that meets with ASTM standards during production of Ti in the HAMR process.

By Hsi-keng Hu

"This paper deals with the flotability of stibnite and summarizes the major experiences and technological innovations of some typical practices of antimony sulfide ores in China. Experiences of cyanide-free and -less flotation of complex antimony sulfide ores and the application of the heavy media process to the preconcentration are described.Performance improvements obtained by innovations in operating techniques are also outlined and discussed. Technical innovations involve: (1) ramification roughing and differential-rate cleaning of stibnite-arsanopyrite ore; (2) the application of the new flotation reagent system; (3) process of separation flotation of Sb-Hg bulk concentrate; (4) extraction of gold from Au-Sb bulk concentrate; (5) flotation recovery of coarse stibnite particles.IntroductionChina is rich in natural resources of antimony and is one of the major antimony producers in the world. During the past several decades, a lot of research works have been done and many experiences in milling practices were gained, some of which are summarized briefly as follows.I. Heavy Media separation of Antimony sulfide Ore at Xikuangshan Hill, Hunan province (1)HMS as a technique of preconcentration of antimony ore has been performed more than ten years in China with good results.1. Ore characteristics The antimony ore of Xikuangshan belongs to the epithermal- metasomatic-filled doposit of antimony sulfide. Major minerals are stibnite (92.1%), antimony oxides (7.9%) and a small amount of pyrite and pyrrhotite; the gangue minerals are quartz, silicic limestone, calcite, hydrous kaolin, sericite, barite and others. The specific gravity of the ore is 2.8 and the specific gravity of stibnite and gangue are 4.6 and 2.654, respectively."

Jan 1, 1988

By S. Tandon

Equilibria studies of selenium distribution for sodium-borate slags were initiated at 1473k under reducing condition as a function of slag composition and alloy composition. The Se distribution coefficient (% Se in slag/% Se in metal) increased from 0.4 to 2.9 with increase in basicity (0.53 to 0.86) for Cu-0.446% Se alloy. However, the results are not very useful from industrial application viewpoint. Therefore, in order to improve the distribution of Se, CaO (10% to 50%) was added to the sodium-borate slag of basicity 0.864. On addition of 502 CaO, the distribution coefficient increased roughly by 100% for slag composition - 44.5% Borax, 22.2% Na2C03, 33.3% CaO and Cu-0.44677 Se alloy. Further, the value of this distribution coefficient has been found to increase by an additional 80% on addition of 20% CaF2 to the above slag for all Cu-Se alloy compositions. Also with increase in initial concentration of Se, the distribution coefficient has been noted to increase.

Jan 1, 1992

By Xuemei Zheng, Aiyuan Ma, Yonggang Zuo, Jinhui Peng, Shiwei Li, Libo Zhang

The effect of moisture content on the dielectric properties and microwave drying behavior of zirconium hydroxide was studied by using an open-ended sensor dielectric measurement system at the frequency of 2.45 GHz. The experimental results showed that moisture content can significantly influence the variation of dielectric properties. Dielectric constant, loss factor and loss tangent all increase with the increasing moisture content. Compared with the conventional drying method, the microwave-assisted drying method resulted in a substantial decrease (81.8%) in the drying time, and the drying effect was better at the lower power level of 600 W. This study offers the useful information on dielectric properties of zirconium hydroxide, which can be used for developing microwave drying applications in mineral processing and designing better microwave sensors for measuring zirconium hydroxide moisture content.

Jan 1, 2015

By K. Prashant Sarswat

Isotopes are critical to a variety of applications including physical science analyses, biology, medicine, pharmaceuticals, and national security. In most cases isotopes must be relatively pure or highly enriched before they become useful. Current isotope separation technologies are relatively inefficient, capital and labor intensive, and often produced by a limited number of suppliers. In the category of isotopes, lithium is among other important candidates. Lithium is found naturally in two isotopes, 6Li which accounts for 7.5% of all lithium, and 7Li which makes up the balance of 92.5%. Each of these isotopes is important to the nuclear industry. 7Li is often used in the form of lithium hydroxide which is used to control pH in pressurized water reactors. The current supply of 7Li is based mostly outside of the United States, and its long-term supply is uncertain. Apart from supply issues, the use of mercury for 7Li separation is also a concern in commercial processing using the most common and efficient approach [1–3]. Hence, a reliable, environmentally friendly, and efficient technique is needed to produce 7Li. In this line of investigations, the authors used a two-compartment system and significant separation was achieved. In this piece of research, some preliminary results are presented including cell design and actual isotope ratio after enrichment. Applying an electro-potential across two electrodes can be used to drive electromigration of Li isotopes. The electromigration is in addition to normal diffusion. Note that 6Li diffuses faster and hence there will be a lowering of the 6Li concentration near the positively charged electrode and an enhancement in 6Li near the negative electrode during the separation process. Similarly, 7Li will be more prevalent near the positive electrode and less prevalent near the negative electrode during the initial separation stage [1].

By Sergio N. Monteiro

Lignocellulosic fibers obtained from plants like cotton, flax, hemp, sisal, jute and many others are natural materials used, since long time, in basic items such as textile, baskets, roofing and carpets. These traditional natural fibers as well as some new ones are nowadays replacing synthetic fibers as composite reinforcement owing to environmental advantages. The heterogeneous characteristic of lignocellulosic fibers is, however, a limitation for application in composites. The buriti fiber, extracted from a tropical plant tree, is recently being investigated as a possible reinforcement for polymeric matrix composites but no complete information exists regarding its mechanical behavior. The objective of this work was then to carry out a statistical analysis on the mechanical properties? uniformity of buriti fibers. By precise dimensional measurements in association with tensile tests, it was found that the mechanical properties depend on the range of the fibers? dimension.

Jan 1, 2009

By Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie

In the present study, the oxidation process of vanadium and chromium bearing hot metal was investigated by using CaO-FetO-SiO2 slags at 1653K in MoSi2 furnace. The results indicated that both the vanadium distribution LV and chromium distribution LCr were of the orders of 2.2~2.4 with the basicity range of 1.32~1.78 and FeO weight percent range of 28%~45%. Both LV and LCr decreased with increasing basicity and decreasing FeO weight percent. The phosphorus distribution LP was of the order of 1.34~1.56. However, LP increased with increasing basicity and decreasing FeO weight percent. The oxidation ratio values of V and Cr in hot metal were above 84% and the values of P were nearly 50%. In other words, it means the addition of CaO in vanadium slag provided a certain ability of dephosphorization along with keeping high oxidation ratios of V and Cr.

Jan 1, 2015

By Pengkai Wang, Huimin Lu, Xiaoxiang Zhang

"In this paper, it was studied an electrochemical reduction process of carbon dioxide in ionic liquids such as 1-n-butyl-3-methylimidazolium hexafluorophosphate ([Bmim] PF6) as the electrolyte. The electrolysis experiments were carried out under current and potential controls. The cathode products contained carbon nanotubes, carbon nanofibers, nanographites, and amorphous carbon. To establish the actual current and potential ranges, the electroreduction of carbon dioxide dissolved in the ionic liquid was studied by cyclic voltammetry on glass-carbon (GC) electrode at room temperature. The electrochemical mechanism of carbon dioxide electroreduction was studied for explanation of all obtained results. Carbon dioxide in ionic liquids was electroreduced, similar to metals oxides being electroreduced in molten salts.IntroductionGlobal warming caused by the increase of carbon dioxide in the atmosphere has become one of the most concerning environment problems, so the solution to this greenhouse effect is very urgent. However, the carbon dioxide is also a cheap and abundant raw material that represents a potential source for the production of chemicals and fuels. Therefore, the development of the technologies that achieve simultaneous reduction and conversion of carbon dioxide to fuels is important. The electrochemical reduction of carbon dioxide is one of the effective approaches to transform CO2. Many investigations have been carried out on the electrochemical reduction of CO2 in both aqueous [1] and non-aqueous [2] electrolyte solutions with different electrodes. The solubility of CO2 in water is very low even under high pressure of CO2, and some investigators have brought focus into the electrochemical reduction of carbon dioxide in organic solvents, because they dissolved much more CO2 than water did. However, the hazardous or toxic properties of organic solvents hinder their use."

Jan 1, 2009

By F. M. Wang, J. P. Lin, G. Y. Tang, H. C. Zhou, Y. F. Liang, F. Ye

"Fe-6.5%Si alloy is a very excellent soft magnetic material compared with conventional Si steel (Si content ~ 3.5%), especially in high frequencies with reduced iron losses and noises. But it is hard to be fabricated due to its brittleness at room temperature. Dynamic electropulsing is applied to the cold rolled Fe-6.5%Si sheet during tensile deformation. Mechanical and microstructural properties are investigated with different electropulsing and strain rate. It is found that the yield stress decreases and the elongation increases dramatically with the application of dynamic electropulsing. It is indicated that the work hardening could be reduced with the dynamic electropulsing during deformation, which provides a promising way to fabricate this alloy sheet much easier.Introduction Fe-6.5%Si (weight percent, same as below) alloy has more excellent soft magnetic properties compared with conventional silicon steel (Si content ~ 3.5%), such as higher resistivity, higher permeability, near zero magnetostriction, etc. and exhibits much lower core losses and noises [1]. However, Fe-6.5%Si is very brittle at room temperature and hard to be fabricated in strip by conventional hot-cold rolling process [2]. This lack of low-temperature ductility has been generally attributed to structural ordering ofB2 and D03 phases [3]. Several methods have been developed to avoid its brittleness, such as chemical vapor deposition (CVD) [4], rapid quenching [5, 6], dipping and diffusion [7, 8], direct powder rolling (DPR) [9], etc. However, hot-cold rolling method is still of interest for industrial applications. In our previous work, this alloy can be cold rolled after certain thermomechanical process and heat treatment [10-13]. The cold rolled sheet exhibits some extent of ductility [11]. However, side cracks are common for the rolled sheet, it is very necessary to improve the ductility of this alloy by other technical applications."

Jan 1, 2012

By Yuanbo Zhang, Zhixiong You, Zijian Su, Bingbing Liu, Guanghui Li, Guang Yang, Tao Jiang

Sodium stannate is widely used in the electroplating and tin alloy industry. But the traditional processes for sodium stannate production are characterized by long flowsheet, high production cost and strict requirement for the equipments, etc. In this study, a novel process for sodium stannate preparation from cassiterite concentrate and sodium carbonate via roasting in CO/CO2 mixed gas then followed by leaching was developed. The effects of roasting parameters on the Sn leaching efficiency were conducted. A Sn leaching efficiency of 77.2% was obtained under the optimal conditions. Sodium stannate (Na2SnO3·3H2O) with a purity of 95.8% was produced by the new process, which is better than that specified for the industrial first-grade product.

Jan 1, 2014

By Sudhir C. Dhara

An attempt has been made on the concentration of Platinum Group Metals (PGM) from the converter matte material by microbial .leaching. Biological oxidation of base metal sulfides such as iron, copper, nickel and free sulfur present in the matte material using Thiobacillus ferrooxidans is an alternative method to concentrate the PGM-and gold. The method which produces a platinum group metals concentrate is comparable to chemical processes and electrochemical process.

Jan 1, 1995

By Chang Wei, Zhigan Deng, Minting Li, Cunxiong Li, Xingbin Li

A direct hydrometallurgical process of extraction molybdenum and nickel from molybdenum-nickel ore by pressure water leaching without reagent was studied. The extraction of Mo and Ni from molybdenum-nickel ore by oxygen pressure leaching, which exploit the characteristic of molybdenum-nickel minerals contain high concentration amorphous sulfide which has highly active, and make the most of easily oxide to sulfuric acid and sulfate at low temperature and excess oxygen presence of the amorphous sulfide. Under oxygen pressure conditions, considerable molybdenum and almost all the nickel were extracted into solution in the leaching process. The results show that with the leaching time for 3~4h, temperature at 150o C, liquid-to-solid ratio of 2mL/g, mineral granularity of 0.074mm, oxygen partial pressure of 0.4~0.5MPa without other reagent, molybdenum leaching percentage can be over 80% and nickel leaching percentage can be more than 97%. Furthermore, about 80% sulfur in the Mo-Ni ore has been transformed into sulfuric acid.

Jan 1, 2014

By Deepu Philip, Pratik Agarwal, Ajay Kumar Shukla, Ishani Shukla, G Rajesh

Steel plants generally employ static BOF end point control models to arrive at a given temperature and chemistry at the end of blow. These end point models have now been supplemented with chaos control models to steer the blowing process in the right direction while the blow is in progress. Merely arriving at the correct end point temperature is however not adequate because in the subsequent stages as well the temperature variations can be large and unpredictable. The present paper deals with an integrated model to take into account the effect of all parameters affecting temperature and composition from tapping to the start of casting to minimize the use of LF or aluminum heating, and also minimize grade mixing. The application of lean operations strategy is explained in which the previous “Push System’ is changed to a “Pull System”, minimizing the use of ladle furnace or aluminum heating during steelmaking.

Jan 1, 2014

By Tian Sugui

By means of the long-term aging treated, creep properties measuring and microstructure observation, an investigation has been made into the microstructure and creep behavior of the casting and rolling GH4169 superalloy after long-term aged. Results show that, after the casting and rolling GH4169 superalloy treated by long-term aged, significant amount of " phase are dispersedly precipitated within the grains of the alloy, and some of the NbC, Cr7C3 carbide are distributed along the grain boundaries. In the range of the applied stresses and temperatures, the creep activation energies and stress exponents of LTA GH4169 alloy during steady state creep are calculated to be Q=541.1kJ/mol and n=16.2, respectively. During creep, the deformation mechanism of LTA GH4169 is thought to be the twinning and dislocation slipping within the twinning regions, and the damaging mode of the alloy is the intergranular fracture, and the non-smooth crystal surface is displayed in the fracture regions of the alloy. Thereinto, the carbides film formed along the grain boundaies has a few effect on the strength between the boundaries, which is a main reason of resulting in the alloy possessing a longer creep lifetimes.

Jan 1, 2009

By Z. Q. Chen, M. H. Loretto, Y. G. Li

"As-cast, As-forged, as-solution-treated, and solution treated and aged microstructures of Ti-15Mo (IMI205) with and without carbon were examined using optical microscopy, scanning electron microscopy .and transmission electron microscopy. Tensile testing was carried out at room temperature. It was found that carbon acts primarily as a titanium carbide former: Titanium carbides increase slightly the tensile strength, but decrease the ductility of IMI205. These observations are interpreted in terms of the titanium carbide morphology observed using SEM and TEM and the phase diagrams of Ti-Mo, Ti-C, and Mo-C.IntroductionIn a recent study on the development of a burn-resistant 13-Ti alloy, carbon was introduced· into the Ti-V-Cr system in order to optimise the mechanical properties. Research results[1, 2] demonstrate that carbon addition can refine the 13 grain size and improve the stability of the 13 phase in Ti-V-Cr alloys. The most attractive result is that carbon addition produced a marked improvement in the ductility of alloys when the carbon content is over 0.1 wt.% in this alloy system. Even after long exposure, the alloy with carbon addition maintains good ductility. One of the main reasons for the ductilising of the alloy is that titanium carbides can getter the oxygen from the 13 matrix.In view of the success of carbon addition in improving the properties and the stability of the Ti-V-Cr alloy, it is of interest to investigate the behaviour of carbon addition in other beta Ti-base alloys. The objective of the present work was, therefore, to assess the microstructures and mechanical properties of IMI 205, a metastable beta titanium alloy, with and without carbon addition using optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), wavelength dispersive X-ray (WDX) analysis, room temperature tensile testing."

Jan 1, 2000