Search Documents

By James O'Brien, Lyman Frost, Grant Hawkes, S. Elangovan, Manohar Sohal, J. S. Herring, Joseph Hartvigsen, Carl Stoots

"Pressing environmental and energy security concerns have brought much needed attention to economic production of hydrogen as the secondary energy carrier for non-electrical markets as well as to meet increasing demand for crude upgrading and desulfurization. While steam reforming of natural gas is currently the dominant method of hydrogen production, it is depleting a valuable fossil fuel while emitting green house gases. Thus, in the long run, efficient, environmentally friendly, and economic means of hydrogen production using nuclear and renewable energy needs to be developed. High temperature electrolysis using solid oxide electrolyte cells is an exceptionally efficient means of generation of high purity hydrogen. It is also capable of directly converting steam and CO2 into synthesis gas. This co-electrolysis process enables conversion of CO2 recovered from concentrated industrial sources into a feedstock for synthetic fuels production. Use of CO2 provides a means of storing hydrogen in a concentrated and convenient form – a hydrocarbon. This is also an effective storage medium for intermittent renewable energy sources such as wind and solar.Ceramatec, Inc and the Idaho National Laboratory are applying solid oxide fuel cell technology to the production of synthesis gas by high temperature co-electrolysis of steam and carbon dioxide. This technology utilizes solid oxide fuel cell stacks to electrochemically remove oxygen from steam and CO2, leaving a clean stream of hydrogen and carbon monoxide suitable for fuel synthesis. By varying the relative concentrations of carbon dioxide and steam, the hydrogen to carbon monoxide product ratio can be controlled as required by the desired type of synthetic fuel being produced from the syngas. The resultant synthesis gas has been used as the feedstock to produce synthetic methane and Fischer Tropsch liquid fuels.Alkaline and proton exchange membrane electrolysis cells typically operate below 100°C, while solid oxide electrolysis cells operates in the 750-850°C range. This higher temperature improves the efficiency significantly. Practically, it translates into a lower cell operating voltage, 1.1-1.4V for high temperature electrolysis vs. ~1.8V for water electrolysis. Hydrogen production is stoichiometric with current in all types of electrolyzers.Carbon dioxide is a valuable resource as a feedstock for energy storage as a hydrocarbon. There is a vast amount of renewable energy that cannot be effectively utilized as grid electricity, but which could be used to convert CO2 to hydrocarbons, offering a solution to the even more difficult (than supplying grid power) challenge of production of sustainable, domestic transportation fuels. Conventional electrolysis and chemical processes could be deployed to accomplish this conversion. However, high temperature co-electrolysis of CO2 and steam to produce synthesis gas using solid oxide fuel cell technology has the potential of improving the efficiency by nearly 50%. A domestic synfuel industry will enable a much larger reliance on intermittent renewable energy than can be accommodated by conventional electric demand profiles while increasing our energy security."

Jan 1, 2010

By Ximeng Zhu

The electrochemical behavior of mineral and coal pyrites in stirred and quiescent alkaline boratelsulfate solutions @H 7.9-10.5) have been investigated using cyclic voltammetry. Significant differences in the electrochemical response of these pyrites were observed. At the mineral pyrite surface, three anodic peaks at about -0.8 V, -0.1 V and +0.5 V (SCE) have been detected along with their corresponding reduction peaks. The first two peaks correspond to FeIFeOI) and FeOI)lFe(III) oxidation. The third peak is present for quiescent conditions but disappears as a distinct peak when the electrolyte is stirred. In the upper voltage region +0.30V (SCE), the current increases markedly during stirring and the reactions correspond to the oxidation of pyrite with the formation FeOII) oxides plus elemental sulfur. Also there is evidence that Fe oxy-ions form. Coal pyrites, under rapid sweep conditions display only the first two anodic peaks, the associated reduction peaks and an additional reduction peak corresponding to one or more of the high voltage oxidation products. After prolonged exposure to high potentials, coal pyrite displays reactions similar to those of mineral pyrite but at much higher current densities demonstrating the much higher reactivity of the coal pyrite. The reactivity sequence was Upper Freeport coal pyrite > Pittsburgh coal pyrite > mineral pyrite.

Jan 1, 1991

By Brian Balmforth

Solvent extraction has been applied successfully to the recovery of a range of metals from a variety of process streams. Particular benefits are derived from the use of new highly selective extractants. These will be exemplified by case studies including the recovery of zinc from sulfate and chloride media using ZENECA's new extractants which show a very high selectivity over iron and the recovery of antimony and bismuth from copper refinery electrolytes using ZENECA's strong and selective extractant DS5834. The conclusions are drawn that solvent extraction is a cost effective technology for metal recovery and recycling, even when used to treat relatively small volume/low concentration process streams, and that it can provide the essential enabling components of a larger system for waste minimisation programmes.

Jan 1, 1996

By R. B. Nourse

The depressed market for Ferrochrome worldwide has forced most producers in this industry to scale down production. Inevitably, many furnaces have been mothballed for prolonged periods, awaiting an upturn in the Ferrochrome market. In contrast, the Platinum industry is experiencing relative stability combined with good prices and they have been looking for cash cows to take advantage of these market conditions. It is, therefore, rather convenient that Platinum and Ferrochrome producers are virtually neighbours in the Bushveld complex of South Afiica, since there is an abundance of spare furnace capacity around (albeit for Ferrochrome). Against this backdrop, Pyromet Technologies (Pty) Ltd, who are currently designing a slag cleaning furnace for Anglo Platinum, was requested to perform pilot scale testwork on a 200kW furnace, in order to establish the suitability to process platinum concentrate and converter slag in a furnace designed for Ferrochrome. This paper provides an overview of the configuration, test conditions, operation and results achieved during the testwork. It also discusses the critical issues, such as refractory consumption, copper cooling and electrical parameters that need to be addressed when converting a Ferrochrome Smelter into a Sulphide Smelter.

Jan 1, 2002

By R. E. Brewer

Pilot scale flotation tests were conducted with a l?ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pet of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated. The tailings were first water leached at approximately 60? C, and the water-leached tailings, containing approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH' and sodium sulfide addition on gold flotation recovery and redox potentials were examined. Maximum gold flotation recovery, 36 pct, was achieved at pH 8,5 with a sodium sulfide addition of 0.18 Ib/st. Overall gold recovery by leaching and flotation was in the range of 70 to 80 pet.

Jan 1, 1989

By Bao Xiancheng

Jinlong's copper flash smelting process started up in April 1997. In the early days of production, lots of equipment and process problems were encountered. But, through continuous improvements in equipment and operation, the designed productivity was reached two years later and the smelting operation has been greatly upgraded since then. After more than 4 yew of production, we have made great achievements, such as increasing the flash furnace availability, significant improvements in operation control, optimization of concentrate burner's structure and operation, and smooth operation of the whole smelter. This paper outlines Jinlong's operational achievements made after commissioning, and discusses problems that were encountered and their countermeasures. Operational experience is also summarized

Jan 1, 2002

By John O. Burckle

For years, the measurement of fugitive emissions from the primary copper converter has defied all attempts based on inferential measurements, It has been concluded by virtually all investigators that the only dependable tech¬nique to measure these emissions would be to completely enclose an operating converter to permit the capture and measurement of all emissions. However, complete enclosure with a metal hood is difficult; many of the most serious fugitive emissions result during periods when the converter must be attended with crane-operated equipment. This approach would require either opening of the enclosure to permit the entry of large items of equipment or completely new methods for charging and tapping converters' The installation of the air curtain hooding system at ASARCO's Tacoma smelter has permitted a quantitative approach to the direct measurement of the fugitive for the first time. In this program, the fugitives captured by the air curtain were measured at a downstream sampling point in the exhaust side of the air curtain system during the various portions of the converter cycle. Emission factors were established for sulfur dioxide, filterable particulate (method 5), inhalable particulate, and selected trace elements.

Jan 1, 1983

By S. V. Subramanian

The tool material and the machine design for high speed machining are well advanced over the last decade but the steel design has lagged behind. The paper examines the design of steel in order to control the sliding tribology for high speed machining under dry machining conditions. In high speed machining of steel, accelerated chemical wear of the tool occurs once atomic contact is established at the tool-chip interface, resulting in poor tool life even with high performance tools such as cubic boron nitride. Recent research has confirmed the occurrence of nanocrystalline grains in the interfacial layer of the chip at the tool-chip contact. The volume percentage of grain boundary is increased significantly (10 to 30%) as the nanocrystalline grain size is decreased well below 30 nm. The solubility of tool material into the nanocrystalline grain boundary is two or three orders of magnitude greater than in the crystal lattice. Further the kinetics of diffusion in the grain boundary is seven or eight orders of magnitude greater than in the crystal lattice. Enhanced nanocrystalline grain boundary diffusion occurring in the interfacial layer at the tool-chip contact causes the accelerated chemical wear. Significant improvement in tool life could be achieved by engineering glassy oxide inclusions in steel, designed to self-lubricate the tool-chip interface in-situ at higher cutting speeds. Thus the control of sliding tribological condition at the tool-chip interface is key to suppress nanocrystalline layer formation at the tool-chip contact and hence prevent accelerated chemical tool wear. Sulfide inclusions are designed essentially to promote chip fracture. In addition, sulfide inclusions are designed to act as a diffusion barrier at the tool-chip interface. The application of inclusion engineering concepts to enhance the tool life in high speed machining will be demonstrated with a suitable case history.

Jan 1, 2006

By Milorad Cirkovic

Kinetics of copper concentrate oxidation in roasting processes in a fluidized bed reactor has been studied at temperatures between 600°C and 720°C using particles of 0.038 to 2.5 mm in average size. The analysis of composition of samples has been done by chemical methods. Phase composition has been determined by Siemens X-ray equipment with Cu anticathode and Ni filters at a voltage of 40 kV and a current of 18 mA. The content of sulphur has decreased from 33.23 to 19.02 mass percent with the increase of temperature, but the content of Fe304 has increased from 0.15 to 17.14 mass percent. The new mechanism of copper concentrate oxidation in a fluidized bed reactor is proposed in this study. It has been shown from the mathematical model that the velocity of oxidation of copper concentrate between 600°C and 720°C is virtually controlled by the rate of diffusion of 02 through the layer of reaction product.

Jan 1, 1999

By Toshiyuki Kozuka

CdTe semi-conducting materials have been expected as solar cell materials because its theoretical energy conversion ratio is very high. The actual efficiency still low, however, many research works have been done in order to improve the efficiency. And crystal orientation is one of possibilities for that. In this work, a new method using intense magnetic field for a control of texture of CdTe crystals will be proposed, where the CdTe film was electro-deposited under an intense magnetic field. CdTe is less affected by magnetic field, because of its cubic structure, but Cd or Te has hexagonal structure, which is sensitive for magnetic field. In this paper, crystal orientation of Cd or Te film, which can be utilized as basic layer for CdTe deposition, will be developed.

Jan 1, 2006

By J. A. Jensen

In-situ composites were produced in both Ti matrix (Ti-20Y) and Mg matrix (Mg-20Ti, Mg- 20Nb, Mg-20Fe, and Mg-8Li) alloys. In Ti-20Y, a < 1010 > fiber texture formed in both the Ti and Y phases, and UTS increased from 240 MPa, (as-cast) to 950 MPa after deformation processing to a true strain of 7.3. Deformation processing produced smaller UTS increases in the Mg-matrix composites, but they showed exceptional resistance to weakening from exposure to elevated temperatures. The Mg-20Fe, Mg-20Nb. and Mg-20Ti composites tolerated 6-hour exposure to 400°C with no reduction in their 250 to 300 MPa room temperature UTS. All composites studied had excellent ductility and machinability.

Jan 1, 1995

The reported values of the standard reduction potentials of the Au(NH3)2+/Au(0) and Au(S2O3)23-/Au(0) couples are reviewed to emphasise the experimental difficulties associated with the measurement of reliable values for these quantities. The standard reduction potential for Ag(I)/Ag(0) in ammonia and thiosulphate solutions measured at ionic strength 0.1 and 25oCis used to predict the following relevant stability constants () for gold complexes based on the linear free energy correlations: Au(NH3)2+2 = 1013, Au(S2O3)23-2 = 1024 and Au(NH3)43+4 = 1033. The equilibrium constant ( 10-11) for the reaction Au(S2O3)23- + 2NH3 = Au(NH3)2+ + 2S2O32- based on these stability constants is in reasonable agreement with the measured value (10-9) based on potentiometric and spectroscopic data when excess ammonia was added to a solution of Na3Au(S2O3)2. This also indicates that the stability constant of Au(NH3)2+ is 9 to11 orders of magnitude less than that of Au(S2O3)23-. Relevant species distribution and Eh-pH diagrams based on the revised data are presented.

Jan 1, 2003

By W. Persson

The first installation at a copper smelter of a Semtech OPC System for continuous, on-line production control of copper converting in PS converters took place in 1994. At present OPC systems are installed at 19 PS converters. The technology presents to the operator real-time information on the progress of the process he is controlling in the form of optical process parameters, thus facilitating dynamic process control. The optical process parameters are based on time- and wavelength resolved registrations of the light emitted by the off-gas flames and identification of correlation between these parameters and characteristic metallurgical process data. The present paper provides a description of the technology as seen by the furnace operators and a summary of operating experiences made during five years of full-scale, operation at various smelters, reviews influences from the technology on smelter operational practises and comments on recent developments as regards new applications of the technology.

Jan 1, 1999

By Ephraim Jeya Kumari

The demand for the titanium dioxide pigments and the shortage of higher-grade titaniferous ores with low radioactivity and zircon sands worldwide has encouraged the development of new techniques for the beneficiation of lesser grade titaniferous ores. The inferior quality ores are invariably richer in radio-active and lanthanide oxides, which severely interfere with the fluidized bed chlorination reaction (FBCR), in which ultra-high purity titanium tetrachloride is distilled off for pigment manufacture. However the present beneficiation techniques require high quality ilmenite ores and are not suitable for upgrading lower grade ilmenite ores which do posses trace metals in the form of lanthanides and actinides as Al-phosphates and zirconium silicates, respectively. The presence of mineral hosts, zircon sand and monazite in ilmenite and anatase also increase in chlorine gas consumption in the FBCR and contribute to a larger volume of hazardous waste production, which must be neutralised at a significant cost before being disposed off safely. In view of the problems described for lanthanide (Ce, Nd etc) and actinide (Th, U) trace impurities in titaniferous ores, an alternative route, which is flexible and more accommodating for processing difficult ores, is discussed. In the new process, which may be used for richer grades of ores too, the ore is roasted in air with sodium carbonate below 950°C to promote the formation of water-soluble sodium ferrite and insoluble sodium titanate phases. In this investigation, the high-temperature roasting process and the ensuing hydrometallurgical leaching steps have been analysed in the context of selective separation of lanthanide and actinide minerals from the main titaniferous mineral structures. Evidences for the selective separation are presented based on the chemical (XRD, XRF, AA) and microstructural analysis (SEM, EDX, EPMA) of roasted mass and the leached product. The efficiency of selective separation is also reported based on the chemicals analysis and the particle size of the materials derived after leaching. The paper highlights the various thermodynamic aspects of reaction equilibrium in the Fe-Ti-O-Na system, and the effect of Eh-pH diagram in the determination of pH required for the better control of the removal of iron and sodium. Two different types of Ti ores, namely ilmenite and anatase, their crystal structure and the phase transformation will also be explained on the basis of wet chemical analysis, XRF, XRD, EPMA and SEM-EDX studies. The method developed examines the technological feasibility of the selective separation process.

Jan 1, 2006

By M. Rosales

By a physical and mathematical modeling, the behavior of the tri-dimensional waving, and the movement of the gases at the Teniente Converter was studied. The mathematical model considers the condensed phases of white metal and slag, along the gas phase, and includes the k-e model for the turbulence description. Both the physical model and the mathematical model allow to conclude that from a fluidynamic stand point the Teniente Converter clearly can melt 3000 tpd of concentrates. Also, both models are suitable to predict the slag fluidynamics and its spacial distribution inside the Teniente Converter, and the splashing in the tuyere zone as well.

Jan 1, 2006

By J. Antonio Barrera-Godinez, S. E. James, J. Sun

The solvent extraction separation of iron from a zinc sulfate medium using DEHPA was investigated. After loading, the ferric ions were reduced in the organic phase using metallic zinc. The ferrous ions produced could be easily stripped into a sulfate solution with pH values in the range of 1.4 to 2.0. The small, laboratory scale pilot system used in this study allowed for continuous cycling of the organic and strip aqueous solutions. It was possible to establish and evaluate a series of steady state conditions under selected operating paiameters. The effects of processing parameters such as solution chemistry, flow rates, zinc metal loading and pH on iron recovery and efficiency were also evaluated. Under proper conditions, it was possible to remove about 5 g/L iron from the organic phase in one stage and to produce a concentrated iron sulfate strip solution containing ferrous ion concentrations in the range of 90 to 130 g/L. Preliminary feasibility tests were also made on electrowinning metallic iron from the strip solutions and crystallizing ferrous sulfate as a means of making a marketable iron product.

Jan 1, 2000

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"For optimum smelting results, proper treatment of the feed is needed to ensure favourable conditions for ignition characteristics, heat balance, mass balance with tolerable impurity levels, and overall process economics. Feed preparation consists of physical treatments before drying (blending), chemical treatments before drying, (roasting, if required), drying itself and physical treatments after drying (fractioning, if required).Effects of fluctuation on mineralogy and moisture should be minimized by blending the concentrates in a bedding plant prior to drying. As an alternative to drying, additional treatments such as roasting for impurity removal may be needed for part of the concentrate.Sustainability, energy efficiency, utilization of waste energy, low gas and dust emissions, product quality, availability and occupational exposure reduction are decisive criteria in drying today. These criteria are best met by the Kumera steam dryer, which has the best energy efficiency, zero CO2 emission, lowest operational and maintenance expenses, and superior availability and product quality.IntroductionFeed preparation plays a crucial role in having a smooth smelting operation and also the overall smelting economics in metal production. Therefore, it is of significant importance for all copper, nickel and lead smelter operations in which sulphide concentrates are fed to the primary smelting furnace. Generally speaking, the higher the metal content in the matte after primary smelting, the more important the feed preparation. This is of particular importance in the direct blister (DB) process for copper production and direct oxygen nickel (DON) for nickel production.Bedding is the first stage in feed preparation. This is very important for the sake of smoothing the mineralogical fluctuation in the feed for better smelting control. Its importance increases as the number of concentrates available for the feed mix decreases."

Jan 1, 2012

By Selvin Yesilay, Munevver Caki, Canbora Bayraktar, Bekir Karasu, Rahmi Imrak

"In this study, the utilization capability of the solid wastes taken from a commercial roof tile and brick factory in Eskisehir of Turkiye has been investigated in the production of stoneware bodies which can be formed by slip casting. At the first stage, X-ray fluorescent (XRF) and X-ray difractometer (XRD) analyses of the wastes were performed. Depending upon the results, a body recipe with an optimum casting concentration was adjusted. The bodies obtained from prepared slips were fired at 1160 oC as glazed and unglazed forms. Then, they were undergone certain tests in order to determine their firing shrinkage values, water absorption levels and optical parameters. To establish what kind of phase formations occurred after firing as a result of waste incorporations into bodies XRD analysis was conducted. Additionally, effects of such a compositional modification on the microstructure of the bodies were examined by a scanning electron microscope (SEM). Consequently, it was concluded that fired roof tile and brick wastes could be evaluated in both glazed and unglazed stoneware bodies. Introduction Stoneware is the general name applied to many wares fired between 1150 and 1300 °C. It has a different and denser structure than those of ceramics produced at lower temperatures. Fired stoneware possesses a lower water absorption value. When matured at a high temperature, it gives a possibility for the use of feldspar as a main ingredient [1-2]. Colors of stoneware can be brown, red, white and most of the times beige. Firing usually takes place in oxidation atmosphere but also reduction can be rarely used. This naturally has an effect on the body colors [3]. Earth, which contains clay minerals, becomes plastic mud when mixed with water, has a capability to be easily shaped and can be hardened without cracking if fired at 900-1000 °C, is referred as one of the brick and tile raw materials [4]. Natural and aesthetic appearances of buildings obtained with brick and tile products, which make them preferable especially for construction sector, are of importance. Because clays being main raw material of that type of productions generally do not exist as pure materials in nature, their usability depends on their mineralogy and impurities they contain [5]."

Jan 1, 2008

By I. Gaballah

The electrochemical behavior of a chalcopyrite concentrate having a high pyrite content was studied in HC1 by potentiodynamic, potentiostatic and galvanostatic experiments using a cell having separate anodic and cathodic compartments. Anodic oxidation of chalcopyrite particles was realized both by their contact with the cunent feeder and by reaction with ferric and cupric ions. An increase of current leads to a more selective dissolution of chalcopyrite. Surface passivation was observed after an electrolysis time related to the cell current. Cathodic reduction of chalcopyrite concentrate seems to be more promising. Almost complete conversion of chalcopyrite to a copper sulfide (Cui.8.S) is observed, whereas no reaction of the pyrite was detected. This confirms the possible selective dissolution of copper from the chalcopyrite concentrate. Copper sulfide obtained by cathodic reduction was leached using a cupric chloride solution.

Jan 1, 1994

By J. Pesl, U. Kemey, F. Sauert

"The CONTOP® smelting cyclone is a water-cooled, upright, high-intensity smelting reactor. The technology for the reactor was initially developed and brought into industrial-scale operation in the area of non-ferrous metallurgy. The two largest smelting cyclones were built with a capacity of 32 tons per hour of copper concentrate mix.The newest industrial CONTOP® plant treats up to five tons per hour of zinc-bearing residues including EAF dust. The highly concentrated zinc-lead oxide produced is sold to the zinc industry. The slag fulfills the leaching criteria and is used in waterway construction. The heat transferred to the cyclone cooling system and the off-gas boiler produces steam from which power is generated in a turbine.V AI has erected a new CONTOP® demonstration plant at MEFOS, Lulea, Sweden. A zinc volatilization rate of 90% was achieved during hot commissioning with Swedish EAF dust.Treatment costs in the range of 85 to 100 EUR per ton were estimated in a feasibility study on the treatment of 73,000 and 57 ,000 tons EAF dust for a group of steelmaking mills in Southern Europe."

Jan 1, 2000