Search Documents

By Erdal Unal

In gate roads where supports are subjected to dynamic loading four times due to retreating longwall panels, it is a real challenge to replace the rigid arches with flexible reinforcement systems and yet to provide safety and stability of these openings within better economical limits. The results presented in this paper are based on a three years of research project aimed at developing safe and economical support systems for gate roads in Çayìrhan coal mine. Çayìrhan -Mine Project includes laboratory and field studies, design analysis, pilot scale design applications and performance monitoring. Based on outputs of the design approach developed, four types of bolts, namely, Split Set, Yielding Super Swellex, Sis-Resin, and Fosroc-Resin bolts were installed in a gate road together with widely spaced yielding steel-arches. In order to compare the performance of these flexible support systems and to provide feed back for the design approach, a monitoring program was initiated.

Jan 1, 1993

By David A. Newman

Strength and physical property testing of coal is conducted regularly by the Arch Mineral Corporation as part of reserve exploration. Pillar design and mine layout are the primary applications for the coal strength data. Distinct differences in pillar behavior were observed during longwall mining at a mine in Southeastern Kentucky. Horizontal and vertical variation in both triaxial and uniaxial compressive strength was observed within the four (4) benches of the Harlan seam. Similarly, geographical variations in coal strength were noted across the Harlan seam reserve. During the past three decades substantial research efforts have been focused upon coal pillar behavior and the refinement of pillar design methodologies. Ironically, little attention was directed to integrating the variability of coal strength into pillar design. The authors examine, through the presentation of case history data, i) typical industrial practice with respect to establishing a database of coal strength for use in pillar design and stability analysis, ii) approaches in which the observed variation in strength in the Harlan seam is integrated into pillar design and stability analyses, and to iii) propose standards for coal cube testing

Jan 1, 1993

By Douglas Morrison

By applying modern 3D numerical modelling techniques to the analysis of a pillar cascade failure in a room and pillar mine, it has been possible to simulate the collapse and develop an understanding of the role of low rock strength areas within the mine. The cascade collapse occurred in a normal strength area but would not have occurred without the influence of a low strength rockmass in one section of the mine. The numerical analysis made it possible to develop a realistic assessment of the residual pillar strength. With the introduction of regular empirical pillar performance assessments, critical pillars or groups of pillars can now be identified proactively. This has led to an aggressive extraction ratio of 90% that manages pillar failure, avoids pillar and roof collapse and prevents surface subsidence. Since the mine also has significant waste products, the use of backfill for ground support has made it possible to significantly improve the performance of strategically located pillars, and so achieve even higher extraction ratios.

Jan 1, 2003

By Khaled Morsy

Most of the available numerical codes simulating the reinforcing effect of fully grouted bolt are accomplished by a series of bar elements which are connected along their length to the host rock by shear springs and sliders. The spring-slider system represents the shear bonding effect between the bolt and the host rock. This paper describes a three dimensional finite element modeling technique for the 3D simulation of fully grouted bolt reinforcement. The proposed technique introduced a physical simulation for the fully grouted bolts. The bolt simulation is composed of a series of beam elements (representing the steel rebar) embedded in brick elements (representing the grout). Because of the complexity of the grout/rock interface, ABAQUS explicit code was used. A modification of the ABAQUS default friction model was conducted to consider the cohesion of the grout/rock interface. The interaction between the grout and the host rock is simulated by the modified friction model. To verify the proposed technique, a simulation of the pull out test we conducted. The results from the simulation were compared with former studies

Jan 1, 2004

By T. N. Singh

With a view to producing increased target output every year, Indian coal mining industry is fast moving towards mechanisation but the present approach of mechanisation suffers from lack of standardisation, mainly due to nonavailability of the cutting data for various machine/rock combinations. The coal seams of the country are relatively hard in nature and the coaling machines are reported to be affecting production and productivity of the coal mine and the very trend of mechanisation. This paper presents the result of extensive study performed to visualise the cutting characteristics of coal seams of compressive strength ranging from 20 MPa to 65 MPa. In a specially designed drag bit type coal plough rig, continuous recording of cutting forces was done with the help of a microprocessor based data logger and the specific energy of cuttability was evaluated at different depth of cut and speed of cutting. The geomechanical properties such as compressive strength, orientation and frequency of cleats etc. and different indices of coal seams were measured in the laboratory and field and relationship was developed for easy determination of specific energy.

Jan 1, 1992

During the last decade mechanical rock excavation has become increasingly widespread in the mining industry and, more in general, in excavation engineering. This technology, especially the tools and their operating mode, has developed according to empirical procedures and for this reason their validity should be ascertained by systematically re-examining the rock breakage processes. This topic has been approached in the framework of a joint research project involving the Universities of Cagliari (Italy) and Wollongong (Australia). The investigation has been carried out experimentally as well as with the methods of numerical modelling which is based on fracture mechanics principles. The first results of this integrated research led to the proposal of an interpretation of rock breakage by means of drag tools and to the identification of a basic correlation between the rake angle of the tool and the grain size of the rock fragments produced and, therefore, the energy efficiency of the operation.

Jan 1, 1990

By Douglas Morrison

Hardrock mines in Ontario generally operate at between 3,000 and 7,500 ft below surface and generally experience significant rockburst activity below 5,000 ft. Since the introduction of bulk mining techniques around 1980, the safety record of Canadian hardrock mines has improved dramatically. However, the process of improvement was not a smooth one and, in the early years, the number of accidents and fatalities actually increased. One incident in 1984 that resulted in 4 fatalities in Ontario initiated a complete re-examination of mining practice and by the mid 1980s many changes had been introduced, driven by new non-prescriptive mining legislation. These changes affected not only the technical discipline of mining engineering but also the management of operational procedures and, together, they resulted in the significant improvements that have continued to this day. The analysis of the rock-fall related fatalities showed 5 major causes (loose, scaling, installing support, collapse and rockburst) and by the mid 1990s fatalities in all of these categories, except rockbursting, had been eliminated and even then, all these rockburst fatalities occurred in one mine which was closed shortly afterward. This paper discusses both the technical and social reasons for the initial failure and the ultimate success in improving the safety of these mines, with implications for mines in other major mining jurisdictions.

Jan 1, 2003

By Z. C. Song

[THIS PAPER WAS TRANSLATED FROM CHINESE TO ENGLISH BY S. S. PENG, WEST VIRGINIA UNIVERSITY] Immediately after coal extraction, the pressure that causes the movement of the surrounding strata is called mine pressure. Through the strata movement, certain features such as supports taking load arise. This is called "manifestation of mine pressure". The existence of mine pressure is ab¬solute whereas its manifestation is relative and conditional. The visible movement of the surrounding strata occurs only when the applied pressure exceeds the plastic breaking strength. Me support begins to take load only when it offers resistance to the strata movement. The key to investigating mine pressure and its control hinges on understanding the rules and conditions for the manifestation of mine pressure. Since the face moves continuously, the mine pressure and its manifestations are also constantly changing. 'Therefore, it should not only emphasize to obtain its instantaneous magnitude, but more importantly the rules of development changes and their relations to the movement of overlying strata. Once this is resolved, one can estimate the movement of the overlying strata through mani¬festation of mine pressure and predict the time and magnitude of incoming roof weighting. Consequently the location and timing of rib excavation can be correctly selected and thus solve several major problems in the design of mining operation.

Jan 1, 1982

By Hideki Shimada

In underground coal mines, grouting method is employed in order to reinforce the floor and to control the movement of groundwater into the roadway. However, the seepage and the reinforcement behavior of the grouting material into the floor are not clearly understood. Therefore, grouting is today normally based on empirical relationships and on the experience of the grouting personnel. To assist grouting projects, it must be acknowledged that many of the flow and the hardening processes occurring during grouting so far defy mathematically analysis. From this point of view. this paper discusses the behavior of grouting material, when it is injected into the roadway floor, by means of 3-D Eulerian-Lagragian seepage analysis. Moreover, the effectiveness of reinforcement grouting on the mechanical properties of slaking-prone mine tunnel floor are studied by means of several laboratory tests. Keywords: Mine tunnel floor, Grout, Seepage, Reinforcement

Jan 1, 2002

By Robert W. Bruhn

A 125 foot high steel lattice frame tower supporting a 500 kV EHV transmission line and located over the gateroads of a longwall mining operation was subjected to ground movements from the mining of adjacent longwall panels. Under an agreement with the owner of the powerline, the mine operator was required to minimize mining impacts on the transmission line. In view of this requirement, the mine operator prepared a forecast of the expected subsidence ground movements prior to the onset of mining. These forecasts, in conjunction with finite element analyses of the tower superstructure under the imposed ground movements and wind loadings. suggested that the structural capacity of the tower would probably be diminished little, if at all, by mining. Ground movements determined by survey during mining of the two longwall panels were found to be in close agreement with predictions. Strains measured in selected tower members during mining generally agreed with values calculated by the finite element analyses. The study confirmed a methodology to predict subsidence and to assess its effects on steel lattice transmission towers.

Jan 1, 1990

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Rarnamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris:- where st = axial compressive stress at failure, MPa; s3 = confining pressure, MPa; scm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (scm )-0? 185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992

By André Zingano

This paper analyses possible causes for floor heaving in room-and-pillar coal mining. The coal mines are in the southern part of Brazil, where the Barro Branco Coal Seam varies in depth from 20m to 400m, and a very thick volcanic formation overlies part of the sedimentary basin. The erosion of part of the volcanic formation causes this large range of overburden thickness, which formed large V-type valleys. The mine in study is located near the slope of one of these valleys. The mine inclined shaft is at the lower overburden thickness area of the valley and the mining is developing toward the thicker overburden area. The floor heave occurred in the crosscuts, which are parallel to the slope valley direction. Numerical modeling was applied to study the stress distribution around the openings; and fieldwork on the floor heaved entries was carried out. The geometry of mining (pillar and openings width) also was analyzed. The results showed that the very weak rock and the high horizontal stress were the causes of floor heave. As the mining gets near the valley slope, the stress distribution around the crosscuts changes considerably. In addition, the stress distribution changes as the mining goes far from the crosscut. Keywords: floor failure, room and pillar, finite element model

Jan 1, 2002

By Keith Heasley

An eastern longwall mine was required to mine through a set of three entries located midway down the length of a panel. Of course, the mine desired to design a successful support system for the mine-through area at the least cost. To further complicate the design process, the mine-through entries were located directly under the end of a previously mined, overlying longwall panel and the entries were close enough to be subject to stress interactions from the overlying seam. In order to accurately evaluate the multiple-seam stresses and modify the mine-through support system appropriately, the boundary element program LaModel was used to model the stress and displacements in the two mines. Using the results of the model's stress analysis, the support density was systematically varied throughout the mine- through entries for optimum sup@ efficiency and economics. During the actual mining of the cross panel entries, the longwall experienced few, if any, additional delays, and overall, the support and mine through of the cross-panel en- tries at Harris #1 was very successful, saving the mine confineable time and money.

Jan 1, 2003

By Michael Alber

Coal resource extraction reaches higher depth of overburden and rockbursts as well as associated seismic events appear to become an additional problem to he addressed by ground control engineers. For example, German coal mines approach a depth of overburden of some 1400 m (4200 ft). Certain strata at those depths and associated high stresses may react upon resource extraction and subsequent deformation by violent release of strain energy, termed rodcbursts. Rock mechanics tests on numerous rock types have been conducted and three types of brittle rock behavior were classified. This paper describes different types of rock behavior in uniaxial compression and discusses a possible classification of rock with respect to their likelihood of violent response upon loading.

Jan 1, 2004

By Gregory E. Smith

"Tensionable headed roof bolt systems are common in the U.S. mining industry. In the last 15 years or so, they have made a comeback as a hybrid system where a mechanical anchor is used in conjunction with resin. When such a system is used, it is common to use a spherical washer to comply with the requirements of 30 CFR Part 75.204(f)(8). This standard requires an angle-compensating device be used in installations where the bearing plate is offset from the roof bolt axis by an angle greater than five degrees. This paper evaluates system performance of four different traditional angle-compensating device/plate combinations including a new patented extruded plate/extruded washer system that improves overall load capacity and stretch.INTRODUCTIONA large western U.S. underground coal mine was using a fully grouted headed rebar system as their primary support. They had developed their component specifications over many years of working with suppliers to improve and optimize these components to integrate well as a system. As shown in Figure 1, the components included a patented 7 /8"" -diameter Grade 60 headed rebar bolt with a flange capable of full bar load (Walker, 2009) and a patented 8 in x 8 in Grade 3 extruded hole bearing plate manufactured by DieMatic Corporation.The mine decided to pursue a fully grouted tensionable system using a mechanical anchor as the tensioning device. Their primary goal was to eliminate the need for the roof bolt operator to secure (hold) the bolt during resin set time. An additional benefit was the increased initial tension on the bolt. To comply with the requirements of 30 CFR Part 75.204(f)(8), regarding tensioned roof bolts, they were required to include an angle-compensating device because a share of the bolt population would be installed at angles greater than five degrees from the perpendicular to the bearing plate. Also, to improve cycle time and torque/tension consistency, the mine desired to have the washers and anchors assembled at the factory. This required the use of a bearing plate with a center hole large enough to accommodate the 1-3/8-in-diameter mechanical anchor to pass though it during assembly by the roof bolt operator. The mine wanted to continue to use an extruded hole bearing plate in the tensionable system, and EMS was asked to propose a plate and angle-compensating device."

Jan 1, 2016

By William B. Beerbower

When full length resin grouted bolts were introduced into U. S. coal mines some 11 years ago, it was assumed that safety would be the primary benefit. There is ample testimony to substantiate the safety factor as an important reason for using resin roof bolts. More recently, it has been determined that many coal operators not only concur with the safety consideration but also benefit economically from the safer working conditions resulting from a reduction in roof falls. IMPROVED SAFETY Some typical roof fall reduction experiences with resin bolting follow: ? Western Kentucky Mine - Resin bolting reduced roof falls by 80%. ? Southern West Virginia Mine - Experienced 141 roof falls between 1971 and 1972. In 1973 with resin bolting, roof falls were reduced 85%. ? Western Pennsylvania Mine - In 1973 had 59 roof falls with mechanical bolts. During the same period of 1974 with resin, only 19 falls were experienced - a reduction of 66%. The overall experience with resin bolted roof support has been an average 50% reduction in roof falls. Long term, this can translate into improved worker morale. As a matter of fact, a general mine foreman at the same Southern West Virginia mine mentioned above commented that improved miner morale was noticeable following the introduction of resin bolting. HOW GREATER SAFETY CAN BE COMBINED WITH INCREASED PRODUCTIVITY IN COAL MINING OPERATIONS Experience has also shown that a reduction of roof falls with resin bolting has resulted in increased production for many coal operators. Some typical examples with mines using resin bolting follow: ? Western Kentucky Mine - Resin bolting contributed to increasing production from 7000 to 11,000 tons per day, due to a 80% reduction in roof falls. This was accomplished in part by a reduction of 50% in timbering requirements and the reassignment of three roof fall cleanup crews to coal production. ? Pennsylvania Mine - Following resin bolting introduction the section showed a 50% increase in production. ? Central West Virginia Mine - Continuous miner production averaged 6 cuts per unit shift prior to resin bolting. Reduction of cleanup time, resulting from improved roof support with resin bolting, increased production to an average of 9 cuts per unit shift. PROPERTIES OF RESIN BOLTING SYSTEMS Several of the important properties of resin bolting systems which contribute to its improved performance are listed below: ? Full length anchored resin bolts and many resin anchored, point anchored bolts provide effective resistance to changing rock strata stresses throughout their length, thereby improving stabilization of rock strata over long periods of time. ? Individual layers of rock are anchored into a single high strength beam providing excellent resistance to vertical and lateral strata movement, the most common cause of roof failure. ? Moisture cannot corrode the fully grouted bolt. ? Has twice the pull strength of mechanical bolts (See Figure 1)

Jan 1, 1982

By Clifford J. Roblee

In this paper, various seismic indicators are evaluated for ability to discern fractures induced into a rock mass by blasting. This is accomplished by presenting results from in situ crosshole seismic studies performed prior to and after a sequence of controlled blasts within limestone and dolomite rock near Austin, TX. Indicators investigated are compression (P-) and shear (S-) wave travel times, first peak and maximum amplitudes, first arrival rise rate, and the linear spectrum of the received signal. Compression wave travel time yielded the most consistent results, while the various amplitude indicators yielded the poorest results for the equipment configuration utilized. In addition, this study documents magnitudes of change in seismic measurements which occurred following blasting. Both P- and S-wave travel times exhibited a wide range of variation due to blasting. Near blast centers below the surficial fractured rock, velocity decreases of about 10% were noted, significantly less than the 50% decrease observed for previously fractured near-surface rock through which the explosive energy was vented. Signal amplitude measurements also varied in magnitude but were less consistent.

Jan 1, 1989

By Lorraine Kent

Comparison of in-situ stress overcore measurement results with those determined from laboratory evaluation of Acoustic Emission (AE) testing on oriented sub-core samples has been carried out for a variety of mining environments. These include UK and German Coal mines at moderate depth, shallow-level South African Coal mines and deep-level South African gold mines. Results show that the `Kaiser Effect' or 'Stress Memory-Damage is readily determinable throughout the brittle deformation process, although particular care is required in interpretation of results during the 'bedding-in' phase of testing and the region associated with unstable crack growth prior to failure. The results suggest that AE provides a useful complimentary method for comparison with existing methods of stress determination. The success of the method can, however, be dependent on both rock type and the likely magnitude of in-situ stress in comparison to the strength of the rock. Keywords: in-situ stress, acoustic emission, Kaiser Effect

Jan 1, 2002

By Radoslaw L. Michalowski

The operation of mobile mining equipment near the crest of stockpiles and wastedumps often results in localized slope failures. The Bureau of Mines has developed a computer code based on a rigorous limit plasticity approach which determines the admissible total weight for a concentrated loading near the crest of these otherwise stable structures. The program is based on a three- dimensional analysis and provides an upper bound solution to the load that can be applied to the top of the operating distances for mobile equipment from the slope edge. This presentation will discuss the application of limit plasticity to the development of the local three-dimensional collapse mechanism, and the use of the computer code based on this approach for mining applications.

Jan 1, 1990

By Ismet Canbulat

The cut out distance in the continuous miner sections in South African collieries is limited to 12 m. However, this distance can be extended to 24 m by the permission of the Department of Mineral and Energy (DME). This paper investigates the risk of roof Calls associated with the extended cut out distances permitted by the DME. Extensive underground experiments have been conducted using sonic probe extensometer under various geological conditions to identify the effect of cutting distance and tinge on the stability of the workings and the performance of the support. The results showed that that the most critical parameter with respect to ground control aspects of extended cut out distance is the bord width, which determines the amount of deformation that will take place in the roof. This was confirmed by the numerical modelling. The results also showed that a significant portion of the maximum deformation in the roof takes place before the ratio of cut out distance to bord width exceeds two. This indicates that once the face is extended more than twice the bord width, the roof will stabilise, assuming that no geological discontinuity is present and that there will be no further geometrical changes in the area as a result of for example the development of an intersection.

Jan 1, 2000