Search Documents

By Sean Harvey

One of the manifestations of the dynamically induced failures in deep coal mines is the violent ejection of coal from the ribs. A possible protection against such failures is the use of a specifically designed dynamic support system with reinforcement units having the sufficient capacity to absorb the kinetic energy of the dynamic failure and a skin support that can adequately contain the disintegrated coal. With this method of mitigation in mind, a recently introduced yielding rock bolt, trade name Roofex, has been identified (Harvey and Ozbay, 2009) as a possible energy absorbing component of a dynamic support system. According to the manufacturer?s specification, the Roofex bolts can yield 300 mm (or more) displacement while holding 80 kN pull load. In order to assess the performance of this support unit in coal ribs, a series of in situ pull tests performed in two coal mines in Colorado. The results show that, under conventional pull test loading conditions, Roofex yielding bolts perform very close to their claimed specifications, thus showing a potential for their use as the main energy absorbing component of a dynamic support system. Further studies are required to confirm the in situ performance of these bolts under dynamic loading conditions and also to develop a containment component for a dynamic support system for the mitigation of dynamic coal rib failures.

Jan 1, 2009

By Changsheng Song

With increasing depth of coal mining in China, the number of coal and gas outbursts has been increasing for years. By means of destressing the protective seam, the gas in the protected seam is drained to reduce gas concentration in the high gassy seams, thus ultimately attaining simultaneous extraction of coal and gas. Base on the simulated material scale modeling and numerical simulation, the protective seam mining method was practiced at No. 8 coal mine in Pingdingshan city. After extracting the No. 15 seam, the overlying strata movement and the deformation of No. 9-10 protected seam were studied. The experiments showed that it was feasible to destress the protected seams with large interburden thickness. As the protective seam was being mined, the protected seam experienced dynamic movement process and the change in vertical stress in the No. 9-10 seam assumed ?W? shape. When the face had advanced 656 ft (200m) from the setup room, the No. 9-10 seam was fully destressed, resulting in easy gas drainage in the destressed zone. Recommendations on mining sequence of multiple seams mining in the Pingdingshan coal areas were made.

Jan 1, 2008

By Tex M. Kubacki

In 2007, the University of Utah Seismograph Stations (UUSS) temporarily expanded its seismic monitoring network in Emery County, Utah, in response to the August 6 Crandall Canyon mine collapse that trapped six workers. In spite of this additional coverage, no seismic events were located in the area during a six-day period (gap) from August 8 to August 13. The Mine Safety and Health Administration (MSHA) ?Command Center Log Books? however, contain references to 16 instances of underground ?bumping? and ?bouncing? that occurred during the gap. When ground truth information provided by the log books is compared to the raw seismic data recorded by the UUSS network, the correlation offers insight into the chronology of mininginduced seismicity (MIS) in the aftermath of the collapse. The new research focuses on identifying and locating seismic events that occurred during the six-day gap using double-difference relocation techniques and correlating them with log book ground truth. Ten seismic events were identified in the vicinity of the mine during the six-day gap, ranging in magnitude from coda magnitude (MC) 0.5 to 1.4. Three of these events were amenable to location by double-difference techniques. The location of one of these events is directly confirmed by ground truth information from the log books. As a result of this new research, the accuracy of Crandall Canyon double-difference locations has been improved, and the number of events correlated with ground truth information has increased. The seismic events occurring in and around the collapsed area appear in two distinct sections of the mine?east and west of the center of collapse. It was originally reported that the post-collapse events occurred in episodic clusters. The first two episodes occurred to the east, followed in time by a cluster on the west, and then by a third episode on the east. With the addition of new events to the data set, this pattern is no longer as clear, although the events still occur in clusters. Only one MIS cluster was found to occur within the bounds of the minimum estimated collapse area (Pechmann et al., 2008).

Jan 1, 2012

By Joe F. T. Agapito

High stresses and adverse geology in deep coal mines in the state of Utah, USA, have caused numerous bumps. The larger bumps have been associated with seismic events with Richter magnitudes of 3.6 and greater, and in some cases have filled openings for lengths of 150 m. A better understanding of the mechanisms and stress levels involved in bumping is needed to help develop improved stress control design and bump mitigation methods. The geology of the area is notoriously bump-prone. The coal has poorly developed cleating and occurs in multiple seams that are often bounded by very strong roof and floor sandstone/siltstone beds. The overburden is formed by thick, competent strata with numerous sandstone channels This geology and deep cover are the major source of high stresses, causing bumps. This paper evaluates live common stress factors responsible for bump problems: depth, sandstone channels, arching, faults, and coal thickness. It uses ease study data from longwall panels with two-entry/yield pillar systems typical of deeper Utah mines. Results illustrate the importance of analyzing stress factor experience to allow a better understanding of the problem.

Jan 1, 2000

By Stephen C. Tadolini

The International Ground Control Conference in Mining has always provided an open forum for the publication, presentation, discussion, and often heated debate on roof bolting systems mostly with attention to how, when, and why they work. During the last 24 Conferences at least 170 papers have been presented by International Experts on these ?simple? devices that range in length from 30-inches to 20 ft and from 5/8 to 2 inches in diameter. Roof bolts are primarily mechanically anchored, glued, cemented, or driven. Bolts are placed vertically, angled, or tied together with special fixtures (trusses and slings). They have been termed active, passive, stick-slip, and several other descriptive acronyms or mining slang expressions. This retrospective paper will present the changes in bolt types and usage, point out some of the biggest myths and hail the most significant advances (according to the authors? opinions of course).

Jan 1, 2006

By Brian R. A. Wood

Any defect activity resulting from an applied stimulus on a structure will generate a stress wave which travels in the medium under the laws of acoustics, thus the name of acoustic emission (AE). AE techniques can therefore provide information on the deformation of both surface and below ground structures, Two operating coal mines were monitored from the surface, and both mining activity and post mining microseismic activity were detected. The nature of the detected AE signals demonstrated that there were a range of deformation mechanisms in operation and that some predictive capabilities were possible with the technique.

Jan 1, 1992

By Axel Preusse

Mining subsidence plays an increasing important role in the Chinese hard coal mining. Reasons for this are a substantial rise of production during the last decade, a dense settlement in many mining regions, the increasing emergence of private residential property as well as a grown environmental awareness. German companies and research institutions hold an over more than 150 years existing know-how in all subjects of mining subsidence engineering. Due to partially comparable preconditions regarding mining depth, mining methods and geological conditions, a close co-operation between German and Chinese mining subsidence engineering experts has been in existence for some years. This German-chinese co-operation is introduced in this paper.

Jan 1, 2007

By John Hoelle

Coal mines in southern West Virginia, south-western Virginia and eastern Kentucky have experienced coal bumps at least since 1933. Most of the bumps have occurred due to high cover, strong roof and floor strata and stress concentrations due to the mining sequence. A longwall mine in eastern Kentucky first experienced coal bumps on the tailgate side of the longwall face in 1989. The bumps continued until 1996. The bumps were the result of: Thick overburden up to 2200 feet Strong roof and floor (strata strengths up to 25,600 psi UCS and elasticity modulus up to 4,800,000 psi Previous over-mining in places Sandstone channels Not all characteristics occurred simultaneously. The bumps produced seismic events recorded up to 4.3 (Richter scale magnitude), and damaged pillars that were up to 147 by 152 feet in size.

Jan 1, 2008

By Dao Hong Quang

This paper describes the numerical analysis of some geotechnical factors influencing the application of Longwall Top Coal Caving (LTCC) method. The study was aimed at comparing the differences in stress distribution in the chain pillars of the face ends and caving mechanism of the top coal in LTCC method between the flat and inclined thick coal seams. The outcomes from this analysis will benefit mine planners in designing the location of roadway development in the next longwall panel. In addition, results from the study will extend the understanding of caving mechanism in top coal section when applying the LTCC method (with the direction of the longwall face is down dip, retreating along strike) in inclined coal seams. The results demonstrate a clear effect of dipping factor on cavability of the top coal and on the stress distribution in the chain pillar of the face ends.

Jan 1, 2008

By Russell Frith

For many years, underground rock mechanics and in particular, roadway/tunnel roof stability has been underpinned by the often unchallenged assumption that roof strength (as defined by the UCS) and stiffness (E) are key stability controls. This has logically led to the proliferation of laboratory testing of rock specimens and the development of indirect geophysical methods to gain estimates of these two rock parameters. Furthermore, many design methods are significantly focussed on replicating rock mass behaviour through either intact or failed constitutive models. Demonstrably the strength and stiffness of the host rock material is commonly used as one of the key indicators of excavation roof stability and it finds either direct or indirect use in just about every rock mass rating system in use today. In more recent times there has been a common move to consider and apply (even if only conceptually at the current time) structural engineering type principles (e.g. buckling) to coal mine roadway roof (and rib) stability. Similarly our knowledge of the in situ stress environment and its likely origins has improved significantly, largely through stress measurements and subsequent analysis. This paper combines knowledge in both of these fundamental areas through a deterministic model for roadway roof stability and in combination with field examples, reaches the almost certainly controversial conclusion that UCS and E are commonly irrelevant, albeit that the former may provide an indication of other relevant geotechnical parameters (e.g. bedding cohesion). As with all hypotheses or rules, there are naturally exceptions and in this case, the most obvious is the tailgate of the longwall panel (with adjacent goaf). Due to the significant change in the strata loading environment of a longwall tailgate as compared to first workings for example, the stability equation materially changes so that UCS and E become critical controls. The point of the paper is to present a different perspective on a traditional mining problem and to challenge geotechnical professionals to keep thinking ?outside of the square? in the never-ending endeavour to improve our understanding of the engineering problems we regularly face. Such an understanding impacts upon such issues as geotechnical data collection from borecore, support hardware requirements and design capabilities. Therefore making the assumption that our understanding is always fundamentally correct could in fact be limiting the development of new and improved engineering in the future.

Jan 1, 2006

By Erik Westman

Few studies have been conducted regarding the location, movement, and relative magnitude of the rear abutment of a longwall coal mine. The rear abutment, or the abutment pressure arch in the gob area, is controlled primarily by the quality of pack of the gob; the more compacted the gob is, the larger the stress would be theoretically. While there is no definitive location for the rear abutment, early studies showed that it could be located as far back in the gob as 300 m (1,000 ft). Like the location of the rear abutment, there has been little research conducted and very few answers as to the exact magnitude of the rear abutment load. Due to the fact that the rear abutment has been studied considerably less than the front or side abutment, the need for further studies is evident. From a ground control standpoint, the location and magnitude of a rear abutment could reveal information on the caving process associated with longwall mining, such as when the initial cave could be expected to occur in future panels. Besides the possible importance of the rear abutment from a ground control perspective, evidence related to the longwall rear abutment could be vital from a ventilation standpoint. The peak rear abutment location could serve as an area for harmful gases, such as methane, to accumulate because forcing air through repacked rock is more difficult than through loose rock. The objective of this study is to determine whether passive seismic tomography could image the location, movement, and relative magnitude of the rear abutment as the longwall face retreated, in addition to the forward abutment and gob. The results of a passive seismic imaging study at a western US longwall show evidence for the location, movement, and relative magnitude of a rear abutment. A clear zone of highlystressed strata is shown where the forward abutment is expected and a low-velocity, damaged zone is shown behind the face where the gob is located. These two zones retreat with the face over a three-week period. In addition, the images show a return to stress levels behind the gob that are slightly higher than overburden stress levels, which is presumably the rear abutment. This occurs at a distance behind the face that is approximately the same as the face width for this mine. We can conclude that passive seismic imaging can be used to identify the location, movement, and relative magnitude of the rear abutment of a longwall mine. This conclusion is dependent on the use of appropriate data collection and processing methods. The information provided can benefit the both ground control and ventilation engineers as they strive to improve the safety and efficiency of longwall mines. The knowledge associated with the rear abutment of a longwall could not only help increase production through proper initial planning and reduce down time, but it could also make positive strides in improving the overall safety surrounding a longwall mining operation.

Jan 1, 2012

By Francis S. Kendorski

Over the past 25 years, the present author has written with several co-authors a series of papers beginning with the landmark paper in the 1st International Conference on Ground Control in Mining in 1981, in turn, based upon U. S. Bureau of Mines (USBM) funded contract research managed by the author with a final report issued in 1979, all concerning this paper?s title subject, Effect of Full-Extraction Underground Mining on Ground and Surface Waters. Initially the work was a summary of British, Russian, and Hungarian experience tailored to United States strata conditions, but has evolved into a consistent and well-documented model of the behavior of strata influenced by full-extraction underground mining such as longwall coal mining. The several strata zones recognized in these works, Surface Fracture Zone, Constrained or Aquiclude Zone, Dilated Zone, Fractured Zone, and Caved Zone, have been observed by several workers in the field. The concepts presented initially 25 years ago have been adopted, rightly or wrongly, by state regulators, ground and surface water researchers, and mining practitioners. The development and utility of these concepts and recent findings will be summarized.

Jan 1, 2006

By Tingkan Lu

To understand the reinforcing mechanisms of the fully grouted resin bolt and clarify its performance in weak roof strata, the field monitoring investigation using instrumented bolts has been conducted in a coal mine. The total time of monitoring was around ten months. In the first 8 month period, the rock bolt performance relates to the initial development of the gateroad and subsequent time dependent strata response. After 8 months, the rock bolt performance relates to the effect of the approaching longwall mining operation, up to the point where the measuring station was destroyed due to the mining operation.

Jan 1, 1998

By John Smyth

Mining through in panel entries and the full face recovery method has been successfully practiced at U.S. Stwl, Mine 50. Suppat of the cut-through entries and recovery room is critical. Traditionally, concrete crib or fly ash cement backfill has been utilized. However, these traditional methods are not feasible at Mine 50 due to the difficulties of the plow face mining through these types of support. Recent development of new cable support systems provides an option for cut-through entry support. Mine 50 and Jennmar Corporation personnel have worked together to design and apply the cable systems in the cut-through entries and full face recovery room to eliminate standing support. To date, a number of full face recovery rooms and cut-through inpanel entries have been successfully mined. The results indicate that the cable systems combined with high capacity shields, have provided sufficient capacity to support the roof. Utilizing the Jennmar Finite Element Analysis (JFEA) computer program (Stankus and Guo, 1996), an analysis of the stress and roof deflection changes as the longwall gradually cut through was conducted. From the finite element analysis data, a supplemental support plan was designed. The history and experiences at Mine 50 are presented. Based on the case experiences and modifications made to the finite element analysis, an improved design criteria for future use has been formulated.

Jan 1, 1998

By Murali M. Gadde

Perimeter mining is a special form of very productive partial extraction method practiced at some mines in the United States. In the Illinois Basin mines where all major coal seams have weak underclay in the immediate floor, experience shows that any long-term ground control issues will arise due to floor failures rather than instability of the coal pillar itself. While there is a significant amount of work done on floor stability associated with regular pillars, no work has been done so far on the stability of perimeter pillars. This paper reports the results of a comprehensive study that was conducted for the first time on floor stability during perimeter mining in the Illinois Basin mines. A special plate template, which mimicked a common perimeter pillar configuration was created to conduct in-situ bearing capacity tests at five mines in three states of the Basin. Additionally, because of the complex shape of pillars created in perimeter mining that defies any closed-form solution, floor bearing capacity was studied using three-dimensional nonlinear numerical modeling. Based on these in-situ and numerical studies, some guidelines are provided for perimeter pillar stability analysis.

Jan 1, 2009

By John Popovich

The MICON RokLok binder system including component and consolidation processes and safety and its first aide are described. The implementation procedures and selection of injection parameters are discussed. Finally a case example of recovering a 30-ft. long roof fall in mainline haulage entry is used to illustrate the economic potential of preventive measures by RokLok injection.

Jan 1, 2001

By Erik Westman

Coal bumps remain one of the industry?s most devastating but least understood phenomena. If changes to the internal conditions of the rock mass could be observed there is hope that bumps could be forecasted. Seismic tomography has been used over the past 25 years in an attempt to image these changing conditions in the vicinity of the longwall face. This paper describes the history and practical considerations of using seismic tomography in bump-prone coal mines. The implementation of seismic tomography at six different longwall mines will be described along with lessons learned. Early studies used mining independent sources of seismic energy, including explosives and sledgehammers. Subsequently more operator friendly sources, such as the mining equipment itself and mining-induced seismicity, were used. Seismic energy sensors have been placed in gateroads and on the surface above the mine. Each of these configurations has associated advantages and disadvantages. Although the results obtained have been encouraging, the application of seismic tomography to monitoring a bump-prone longwall face is still immature. The ultimate goal of clearly imaging changing stress conditions in the longwall panel in a manner that does not inhibit mining operation is still distant, yet drawing nearer. When this goal is achieved, the industry will have a capable tool for identifying locations where bumps are imminent.

Jan 1, 2008

By Mingju Liu

China has been suffering from coal and gas outbursts since 1950s. Nowadays, the situation has become worse than ever with the need to mine deeper coal deposits at higher production rates in a more complex underground mining environment. In the year 2006 alone, 37 outbursts occurred in underground coal mines with a death toll of 232. This paper describes a case study of an outburst event, which occurred in July 2006 during the shaft development of the Mengjin Coal Mine, Henan Province, China at a depth of 768m below surface. Detailed analysis of the possible causes that led to the occurrence of the outburst is reported. These include the study of complex geological features, gas storage conditions, possible improper technical management practice as well as incomplete prevention and control measures. Based on the case study and the observation of outburst occurrence in China in the year 2007, suggestions have been put forward to help prevent and control future coal and gas outbursts.

Jan 1, 2007

By Rob Thomas

Pre-driven recovery roads are used to speed up the longwall recovery process by reducing bolt-up requirements and by improving ground conditions on the face during the removal of the powered supports. To lower the geotechnical risks associated with the use of pre-driven recovery roads, and so improve its overall acceptance in the industry as a viable alternative to more conventional, potentially difficult and costly longwall recoveries, this paper outlines (i) a geomechanical model for the use and design of pre-driven recovery roads, (ii) an updated version of the worldwide database on pre-driven recovery roads, (iii) a summary of the various methods of holing a longwall into a pre-driven recovery road and (iv) a series of relevant ground support and strata management guidelines.

Jan 1, 2008

By John Latilla

Exxaro Mining?s Matla Coal situated in Mpumalanga, South Africa operates two shortwall faces on the No 4 and No 2 seam while the No 5 seam has also been longwalled in the past. Severe strata loading events have lead to a number of serious roof falls on the wall face (facebreaks) resulting in safety threats as well as considerable production losses. In 2002 the No 4 seam shortwall suffered a facebreak restricted mainly to the tailgate side of the mining panel due to a thick, near surface dolerite sill not breaking properly. This was partly due to the premature suspension of longwalling in the overlying No 5 seam. The resultant overloading lead to severe pillar damage and subsequent bord collapse. Surface pre-split blasting was successfully used to relieve the pressure as well as to pre-condition the dolerite above the following two panels. The shortwall on the No 2 seam has experienced mid-face loading due to No 4 seam chain pillars lying over this area and creating a secondary cantilever effect. Pre-split blasting of the solid rock above the No 4 seam pillars has resulted in a significant reduction in the number of facebreaks. The panel layout of the No 2 seam was subsequently changed so that the chain pillars on both the No 4 and No 2 seam are superimposed whereas previously they were offset.

Jan 1, 2007