Search Documents

By P. D. Morrell

Jetbelt is the trade name for the air supported belt conveyor. It does not use troughing rollers. Jetbelt conveyors support the conveyor belt on a thin film of air. The belt rides in a steel trough which has small holes equally spaced along the bottom of the trough. Air comes through the holes under the belt, thereby supporting the belt. The air pressure is provided by a single centrifugal blower that creates very low pressure, between 249 Pa and747 Pa [10" and 30" water column], depending upon the tonnage being conveyed. The volume of air required ranges between .001415 m3/S and .00283 m3/S [3 and 6 CFM] per lineal foot of conveyor. Therefore, depending on tonnage being conveyed, a 304.8m[1000'] conveyor might require as little as 1.415m3/S [3000 CFM] or as much as 2.83m3/S [6000 CFM.]. (See Figure 1) Horsepower requirements can be less than troughing idler conveyors and considerably less than some other forms of bulk conveying. Savings are most significant in horizontal and down hill (regenerative) conveyor designs. Horsepower to lift material, of course, does not change.

Jan 1, 1984

By Eugene E. Brucker

In recent years, there has been increased interest in construction problems presented by karst topography. Twenty-five years ago, karst areas were by-passed for development. Today, the high cost of land and population pressures are requiring utilization of karst areas. Areas exhibiting karst features can be satisfactorily developed so that construction can proceed in a normal manner; or the areas may be left undeveloped and the underground drainage system abused by improper use causing or contributing to structural collapse, excessive erosion, and a grave threat to the stability of land development and the environment. The term "karst" is a comprehensive term applied to areas underlain by soluble rock that possess a topography formed chiefly by the dissolving of rock and the diversion of surface waters to underground routes. There are four features which contribute to the maximum development of karst. 1. A soluble rock, preferably limestone, must be present at or near the surface of the ground. Occasionally, dolomite will suffice.

Jan 1, 1970

By Robert A. Bauer

Introduction A longwall mining demonstration currently in progress in the Herrin (No.6) Coal Member near Benton, Illinois, involves the extraction of three adjacent panels by the longwall method. The first panel was completed in May, 1977. The Illinois State Geological Survey is involved in this project for two reasons: (1) to detail the geology of the roof and relate the geologic features to the behavior of the roof during mining operations, and (2) to study the nature and occurrence of coal balls (carbonate petrifactions of peat) encountered during this demonstration. General Geology of Area The stratigraphic sequence of beds immediately above the No. 6 Coal in this area, ranging from oldest to youngest, is: gray shale (Energy Shale Member), black carbonaceous shale (Anna Shale Member), and argillaceous limestone (Brereton Limestone Member) (figure 1). In some areas of the mine, where one of these units may rest directly on the coal, one or more of the members is absent from the stratigraphic sequence. The nature of roof for the area is shown in figure 2. It is greatly exaggerated in the vertical direction. The Walshville Channel, 11.3 km west of this mine, was a river at least in part deposited at the same time as the coal. The gray shale wedge on top of the coal, which thins away from the channel, is thought to represent an overbank deposit of mud from the channel. The next layer deposited on top of the gray shale, and on the coal not covered by gray shale, is the black carbonaceous shale, believed to represent a mud deposited in a brackish environment. The area where the roof lithologies change rapidly from one shale to

Jan 1, 1977

By Jack D. Melin

The commercial development of the Liwell Screen is a result of a thorough search for a non-blinding and highly efficient screening device capable of handling even the most difficult-to- screen feed materials. A proprietary development of Hein, Lehmann A.G. of Duesseldorf, West Germany, the Liwell Screen utilizes a unique flexible deck motion for sizing a variety of sticky, high surface moisture feed materials including raw coal and lignite at separations ranging from 3/4-inches (19mm) down to 10 mesh (1.5 mm).

Jan 1, 1983

By Robert V. Price

It is a pleasure to be here today to discuss coal's prospects with the Society of Mining Engineers of AIMS--- a group destined to play a crucial role in shaping our national energy future. Much has been said lately about attaining domestic energy self-sufficiency, but to date, little has been done. Oil tankers from Venezuela and Kuwait continue to glide across the seas to meet our incremental energy needs. Meanwhile, our principal domestic energy resources -- oil and natural gas reserves in the Outer Continental Shelf and the oil shale deposits and the coal lands of the West -remain untapped. Help, however, appears to be on the way. In a forceful address last fall, President Ford called for the elimination of oil as a fuel for base-loaded power plants and its replacement with coal by 1980. He also urged the accelerated leasing of federal lands on the Outer Continental Shelf, the resumption of coal leasing on federal lands, and the development of a new energy conservation policy. There are, of course, many details left to be worked out. Language must be developed to put statutory flesh on the conceptual bones spelled out by the President. Congress must act. Regulations must be approved and tested, if need be, in court.

Jan 1, 1975

By Hans von Michaelis

Welcome to RANDOL GOLD FORUM 88. It is clear from the list of delegates and speakers that this conference will lead to excellent discussions of the latest developments in this fast-moving industry. Less than a year ago Randol International Ltd. published an eleven-volume report titled "Innovations in Gold and Silver Recovery - Phase 111". In the short space of time since then, many new developments have been noted, many of which will be described in this Forum. I believe that some of the more significant innovations currently under development are those that address the following:

Jan 1, 1998

By P. G. Irwin

Natural resins, those derived from coal and those mined in the Uintah basin, face challenges from synthetic resins that are derived from petroleum sources and rosin or wood sources. In the past, fossil resins from coal were produced by various companies, the last one being Hercules, Inc., which sold BLACKHAWK resin until a fire destroyed the plant in the mid 1970's. Approximately four to fjve million pounds of BLACKHAWK were produced and sold mostly to the printing ink industry. Uintaite, more commonly known as Gilsonite® resin, was widely used by various industries, notably in printing inks, coatings, stains, adhesives, foundry, asphalt paving, and oil well drilling muds. Gilsonite has lost market share over the last thirty years to various synthetic resins particularly hydrocarbon resins that are derived from petroleum sources.

Jan 1, 1990

By A. Konya

"INTRODUCTION Underground Mining and Construction projects face several challenges unique to the underground environment compared to the surface environment. The goals of an effective blasting program are the development of a blast pattern that minimizes cost, maximizes face advance, and provides the desired fragmentation and face profile. In addition to these , mines must consider the very real operational problems that occur such as drill deviation, ground vibration, and deadpressing or sympathetic detonation of explosives. These operation problems lead to increased costs and decreased production in the mine, hurting the bottom line. Combined with these problems, underground blasts can be difficult to monitor and evaluate due to tight spaces, dust during the blast obscuring video, and the need to evacuate the immediate area with no clear line of sight to observe performance. This creates an environment which most mines know that blasting can be improved in their underground operations, yet most are hesitant to change due to fears of the shot freezing, misfires occurring, and questions about how to achieve a proper design. The explosive companies and shot service providers also offer limited assistance or knowledge in the underground blasting realm, unlike with surface blasting, leaving many underground operations in the dark. It is for these reasons that most underground operations are operating decades behind the current technologies and incurring significant costs, both real and hidden, from there blasting operations. This paper discusses philosophical changes to designs that need to be made for effective design and modifications of underground blast patterns to prevent deadpressing and precompression of modern explosive products (Konya, Konya, & Worsey, Modern Blasting Method Selection, 2017). While numerous different methods of underground heading development exist, there are two types that are used in a majority of mines around the world, these are the burn cut and the V-cut. The burn cut is a parallel cut that has holes that go straight into the face and are primarily used in smaller opening (due to ability to pull deep rounds with smaller room widths) and metal mines (helps in ore dilution and greater fragmentation). The V-Cut is a cut that uses angled drilling towards the center of the face (in the traditional method) and is primarily used in underground aggregate operations due to its cheap cost but larger fragmentation sizes and greater throw of the muckpile. This paper will discuss these two forms of cuts specifically with the understanding that modifications to these can be applied to other parallel and angled underground heading techniques. BURN CUT The burn cut is one of the older forms of underground blasting, where a part of the blast (burn) of a shot is heavily loaded with additional empty (relief) holes with the goal of smashing (aka burn) and pushing/blowing all the material in the burn out to provide relief for subsequent blastholes. The relief holes in the burn cut provide a parallel relief for the holes that are firing to break too creating a second plane of relief, however these are extremely small and can cause many problems if a design is improper."

Jan 1, 2018

By C. L. Schneider

The calculation of the liberation spectrum in the product from continuous milling operations is a problem of considerable importance and is difficult to solve because the population balance equation must be integrated in two-dimensional space. Complete solutions require the estimation of a large number of parameters unless a structural model of the ore texture can be used. A very simplified textural model based on the use of the modified Andrews-Mika diagram and the PARGEN simulation of multi-phase particles has been formulated and is used to simulate the behavior of a continuously operating laboratory ball mill. A sensitivity analysis for this mill has been done to show the likely effect of model approximations on the predicted liberation spectrum which will be measured.

Jan 1, 1992

By Steven B. Van Kouteren

Added value is a term loosely used in the industry, but what exactly does it mean? What does it take to make a value-added product and more importantly how does a company maintain the value added to its products? Most people agree that value-added means the value of a mineral minus the cost to produce it. But what is misleading is that producing value added products does not necessarily guarantee the profitability of the products. In some cases firms that make "value-added" products are not very profitable. It is not only important to understand how to make a value-added product but also how competitive forces in the market can erode the value added. Therefore, when we look at value-added opportunities, we must understand how to obtain the value added and more importantly how to maintain the value. There are four major factors that limit a company's ability to add value to its products. This paper will examine these factors and will use the ground calcium carbonate and mica industries as examples.

Jan 1, 1990

By G. M. Swinkels

It is generally accepted, that oxygen is a necessary reagent for the flotation of galena with xanthate. Recent measurements have shown (1) that under plant conditions oxygen may be in a short supply to the extent that it limits the rate of flotation. Thus, it becomes important to define the exact role of oxygen and establish a model for the rational design and control of flotation separations, involving oxygen as a reagent. All theories or, the flotation of galena assign oxygen the role of an oxidant. However, they disagree on a number of questions: 1) Is the galena or the xanthate being oxidized? 2) Is a lead dixanthate or dixanthogen the actual collector? 3) Is the oxidation process in which oxygen participates of a chemical or an electrochemical nature? The last question arises from the observation (2) that an anodic bias as well as oxygen will make a galena surface hydrophobic in the presence of xanthate. Theories which are based an the premise that the influence of oxygen is of an electrochemical nature offer elegant models of galena flotation. However, full advantage has not been taken of available electrochemical techniques to discriminate between theories and this is the area towards which this research has been directed (3).

Jan 1, 1970

By R. M. Von Storch

Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that influence miring. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined, conditions are met in most coal mines in southeastern Utah including those of the United States Steel Corporation. This coal bed measures up to 16 feet in thickness, the pitch is as much as 25% and mining is under a cover approaching 2, 000 feet. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colorado. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the southwest..It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development.

Jan 1, 1967

By J. Davitt McAteer

Improvements in the control of coal mine dust have occurred over the past 25 years. Simultaneously, dramatic improvements in coal mine production technology have occurred, particularly at mines where longwall systems are in use. Production rates of longwall systems have quadrupled since 1978, and dust generation on these systems has significantly increased. However, technology to address control of the resulting increased levels of respirable dust has not kept pace, and many high-production longwall sections continue to experience problems with respirable dust control. This paper seeks to enlist the entire mining community in the effort to resolve the health problems presented by excessive levels of respirable coal mine dust, particularly on longwall systems. These systems are expected to increase in number and length, and to generate increasingly higher levels of dust as production rates of these systems continue to rise.

Jan 1, 1995

By F. J. Murrell

No other region of the world is enjoying the tremendous growth of power use that is currently being experienced in Asia. Fortunately for those of us in the coal industry -particularly in Asia -the preponderance of the power plants being planned or under construction designed to use coal as the power plant fuel. This has produced a significant increase in the demand for steam coal, which has in turn encouraged many of us in the industry to develop new coal mines. One country that has enjoyed very substantial growth in coal production is Indonesia. This developing country of 195,000,000 people who live on the nearly 13,000 islands of Indonesia have emerged very quickly to become the third largest exporter of steam coal, following only Australia and South Africa. Almost all coal in Indonesia is mined by surface mining methods. This paper will examine the surface mining of coal in Indonesia, as it continues to be an important part of the supply equation for coal in Asia.

Jan 1, 1996

By M. Heger, V. Lund, P. Mongeon, D. Bogunovic, V. Kecojevic

The U.S. coal mining industry consumes a significant amount of energy, primarily diesel fuel and electricity. The continuous global increase in energy demand, high energy prices and environmental issues related to carbon dioxide emission represent a substantial challenge for the mining industry. This paper presents the result of research on development of an integrated data environment system for analysis of energy consumption in a surface coal mine. A case study on an operating surface coal mine is carried out to demonstrate the practical application of the developed system. The research work presented here may be used by mining professionals to help provide the answers to the crucial questions of when, where and how much energy is being used. This developed system represents a framework for efficient management of energy consumption.

Jan 1, 2009

By Donald R. East

For many years there has been increasing pressure on mining companies, not without some justification, to design tailings storage facilities which guarantee some degree of protection against process solutions entering local groundwater and surface water flows. A fairly straightforward approach to achieving this has been to design conventional water-retaining type structures, and this has often been reinforced by the need to store large volumes of process water and seasonal run-off within the tailings facility. The conventional design uses naturally occurring geological barriers and a conventional embankment with possibly a grout curtain, or artificial barriers around the entire facility, using either imported low permeability soils, admixtures, or synthetic liners. While these approaches may achieve the primary objective of minimizing seepage, various other factors should be considered. Firstly, by depositing the tailings slurry in a sub-aqueous manner, the tailings, especially if relatively fine grained, will settle to very low densities and little or no on-going consolidation may occur over the operating life of the mine, There have been many cases where measured pore pressures within the tailings mass equal the total overburden stress, i.e., no consolidation and no strength, many years after decommissioning.

Jan 1, 1998

By J. E. Castle

The essential foundation upon which to build an effective marketing program in industrial minerals is the ability to produce competitively mineral products meeting precise customer specifications and to ship them promptly and on schedule. Without this prerequisite, all the other factors in a second marketing program-creative sales management, energetic solicitation, advertising, technical service, new products, etc.are without meaning. The primary image to be created in the mind of customers is that of the reliable and prompt supplier of mineral products at competitive prices and of standard, uniform quality. With this favorable image implanted, it becomes possible to integrate the other essential factors into a strong marketing program; and without this image, little can be accomplished. After having .made provision for the basic product ion position outlined, there are then two fundamental considerations in the design of a successful marketing program for industrial minerals. The first of these is that the number of potential customers for the typical industrial mineral product is, relatively small, and indeed compared to the number of customers for consumer products, the number is actually minute. The second consideration is that the customers for industrial minerals are manufacturers and producers rather than consumers. These two factors lead to a necessity that the marketing program be specifically and uniquely tailored to fit the individual mineral product to be sold and to conform to an existing pattern of distribution.

Jan 1, 1962

By S. J. Aparo

Phosphate mining and beneficiation in the State of Florida are presently being carried on by 12 different mining companies with a total of 21 mining and flotation plant locations. Their combined production of both washer rock and flotation concentrate was approximately 28,000,000 long tons in 1968. This accounted for 70-72% of the total U. S. production and close to 30% of the world's output of this mineral. From this extensive activity in the Florida phosphate field, one basic flow sheet for beneficiation of the ore has developed over the years as the most commonly employed. In fact, all of these plants with the exception of two beneficiate Florida pebble phosphate using a basic operation as illustrated in Figure I. The two plants which differ from this general approach are not using raw matrix as feed. In one instance, +14 mesh pebble is ground in a rod mill to release free silica which is subsequently removed in a cationic froth flotation circuit using an amine acetate blend and kerosene. This technique generally results in a 4-7 BPL unit upgrading of the feed pebble. The other exception to the standard flow sheet illustrated in Figure I is an operation which is beneficiating tailing piles. In this case, the material is first subjected to cationic froth flotation in order to upgrade the feed to a point comparable to normal matrix. Thereafter, after, the phosphate is floated in an anionic rougher circuit followed by cationic flotation of the silica in a cleaner circuit.

Jan 1, 1969

By F. D. Huntley

Raw materials used by the Flat Glass Industry are known in the Industrial Minerals geology sector as Specialty Products. These pro- ducts must meet specification limits usually not the same for all glass manufacturers. Evolving new glass compositions will require mineral concentrates of consistent purity being produced within economic limits that will assure market viability of the resulting glass product. The amount of success the Flat Glass Industry will achieve by developing and maintaining domestic production centers will be determined by many economic factors which affect the costs of doing business. Technological developments by mineral processors must continue in order to achieve more efficient production of high quality glassmaking raw materials.

Jan 1, 1986

By R. Schuerch, C. Cimiotti, M. Piemontese, N. Karlin, P. Perazzelli, P. Halton

The new Los Angeles, California JWPCP effluent outfall tunnel will transport secondary-treated effluent from the Joint Water Pollution Control Plant in Carson to White Point Manifold. The tunnel will be approximately 7 miles (11 km) long with a finished internal diameter of 18 ft (5.5 m). The TBM is designed to cope with high water pressure up to 10 bar. The geotechnical challenges are due to the heterogeneous subsurface conditions: in the first half of the alignment, the tunnel runs through soils with a low overburden under urban areas, and, in the second half, the tunnel runs through extremely weak, intensely faulted rock masses with high overburden. Following an overview of the project, this paper focuses on the northern portion of the alignment and presents a decision-making procedure developed during pre-excavation phase in order to cope with the expected heterogeneous conditions during mining. The risk assessment and the TBM operational design of the southern portion will be dealt with in a future paper.

Jun 13, 2023