Search Documents

By T. F. Dumm

With increasing interest in the physical cleaning of fine coal, there is a need for extension of the sink-float analysis procedure to finer sizes. Problems arise, however, in ensuring complete dispersion of the particles in the heavy liquids. A procedure has been developed in which surfactants are used as dispersing agents and solids concentration is minimized (using a simple formula to estimate the minimum weight needed for statistical reliability). Using centrifuges to increase separation rates and sub-sieve particle size analysis of the specific gravity fractions, a complete size-specific gravity distribution can be obtained. Analyses have been performed on coal samples as fine as -10 µm.

Jan 1, 1987

By Miguel N. Herrera, Abbas H. Mirza, Fiona M. Doyle

The standard test methods used to determine the pyrite content of coal and mineral wastes, and their propensity to release acidic drainage, are critically reviewed. In addition to analysis of total sulfur by combustion, test methods using selective oxidation of pyrite by HNO3 and H2O2 are available. The oxidation kinetics of pyrite vary appreciably from sample to sample, and it is difficult to ascertain whether complete dissolution has occurred in heterogeneous materials. The reliability, reproducibility and suitability of different standard test methods were studied, using well characterized ore and coal pyrite samples. The kinetics of pyrite dissolution were also investigated. The results are discussed in terms of the fundamental chemical and physical characteristics of each sample, and the implications for waste characterization are considered.

Jan 1, 1992

By Edwin Itzig-Heine, Daniel Traylor, Bernard Tarralle, Michael McKenna

This paper discusses the challenges associated with the design and construction of a dual-cell, “figure eight” shaped shaft in saturated, soft ground for the Northeast Interceptor Sewer project in Los Angeles. The shaft will be excavated to a depth of41 m and used to launch two EPB TBMs. The specifications required concrete diaphragm walls, embedded below the shaft invert, and a grout curtain beneath the wall. To control water pressure and basal stability without a grout curtain, wall panels were embedded deeper than required into a stiff, cohesive deposit. Details of wall panel excavation using a Hydrofraise are presented.

Jan 1, 2003

By Keith Olson

In the heart of Appalachia, where coal mining has shaped communities and economies for generations, Bluefield State University (BSU) has made a landmark decision to reestablish its mining engineering technology program. This move comes at a critical juncture for both the university and the mining industry, which faces significant workforce challenges amid evolving technological demands and an aging professional demographic. The program’s revival represents an educational initiative and a strategic response to industry needs and regional economic development. Nestled in the mountains of southern West Virginia, BSU has a storied history intertwined with the region’s mining heritage. The institution’s decision to bring back this specialized program after a hiatus of several years signals a renewed commitment to serving both regional industry demands and providing career pathways for students in an area where the cyclical nature of resource extraction economies has often limited economic opportunities. “This program’s return reflects our deep understanding of this region’s needs and our commitment to preparing graduates for meaningful careers that support our local industries,” said Darrin Martin, president of Bluefield State University. “We’re bridging the gap between education and industry with a modernized curriculum that addresses today’s mining challenges while preparing for tomorrow’s innovations.”

Jun 1, 2025

By Jr. Foot

EIMCO Process Equipment Company has introduced the new SmartCell series of conventional flotation cells. The flagship of this new development is the 5000 ft3 cell that is the largest available in industry. This new series of cells includes a cylindrical tank design, a conical draft tube and froth crowder. Optional air control, wash water addition and embedded expert control are available. A discussion of the design parameters, energy efficiency, testing, and commercial plant results are presented.

Jan 1, 1997

By Philip K. Chan

Batu Hijau is a new copper and gold mine located on the island of Sumbawa in the Republic of Indonesia. This paper details the design and construction of the Batu Hijau overland conveyor, one of the most challenging efforts of the project. The 1.8 m wide, 5.6 km long conveyor has a design capacity of over 10,000 mtph and carries primary crushed ore through the steep mountains of Sumbawa, which necessitated a 160 m vertical downhill section, a 75 m vertical uphill section, ten vertical curves and one horizontal curve.

Jan 1, 2000

By Roberto Pimentel de Souza

Since 1976 CVRD is carrying out tests to develop a type of pellet made with organic binder. One binder that showed good possibility to be used in industrial plants is Peridur. An extensive framework of tests was run in CVRD's pilot plant. The results are presented in this paper. Finally, the decision was taken to carry out an industrial production of 50.000 t of pellets. It was scheduled for March '81. The results are shown in this pager. It was not observed any detrimental effect of the peridur neither in the process nor in the product quality.

Jan 1, 1981

By B. J. Arnold

Froth removal rate is perhaps the most important parameter in scaling up from laboratory tests to plant froth flotation circuits. The WEMCO froth factor, the percentage of the froth height over the lip of the cell, accounts for the difference between laboratory and plant froth removal rates. As laboratory tests are generally run with a high pulp level, laboratory results are directly comparable to plant results only when a high froth factor (high pulp level) is run in the plant. When a plant does not have a high pulp level, laboratory results must be modified by using a ratio between laboratory and plant kinetics to predict plant results. This ratio, which accounts for the froth factor is important in testing any new reagents or reagent dosage levels. CQ Inc. researchers have used predictive scale-up equations using this froth factor coupled with equations for kinetics and the residence time distribution in the froth flotation cells. These equations show that modifying the froth factor in the plant can have a large impact on flotation cell yield and reagent use. EQUATIONS DESCRIBING FROTH FLOTATION Scaling up from laboratory- to plant-scale coal froth flotation has been the subject of much research and debate over the years. Determining the proper rate equation to describe flotation kinetics and an equation to describe the residence time distribution in a bank of flotation cells have been particular areas of study. As shown in Tables 1 and 2, various rate equations and residence time distribution equations have been proposed in the literature. These equations consist of one or two parameters giving the rate constant(s) in units of time-1 and a parameter for recovery at infinite time, [Roo]. Dowling, Klimpel, and Aplan (1985) evaluated the rate equations in Table 1 for their ability to fit froth flotation kinetic data and found that all of the equations give reasonably low standard errors. Several of these equations, however, proved to have superior confidence limits for the parameters. Other equations have also been proposed to describe the recovery versus time profile. Most recently, Diao et al. (1992) proposed a first-order form with a sine wave distribution. As indicated in Table 2, investigators have suggested many equations to describe the residence time distribution in continuous froth flotation. To measure the water residence time distribution in a bank of cells, a soluble tracer is often used, with the level of tracer being measured over time at the tailings discharge. This response is then put on a dimensionless basis as described by Austin et al. (1984) in order to compare mixing behavior between cells or under different conditions. Coal flotation cells are generally of the flow-through or hog-trough variety allowing for some degree of backmixing and short-circuiting. While the water residence time distribution (see Figure 1) at the end of one cell in a bank of 1.4 cu ft WEMCO froth flotation cells may approximate perfect mixing conditions (Arnold, 1989), the water residence time distribution at the end of a bank of cells does not. Figure 2 shows the RTD for various flotation cell types compared to that for perfect mixers in series. To better describe the water residence time distribution in coal froth flotation cells, Van Orden (1986) used an equation similar to the perfect-mixers-in-aeries equation. This

Jan 1, 1993

By Rush H. Spedden

Antoine M. Gaudin was a vigorously creative man and throughout his career an internationally respected leader of his chosen profession of mineral engineering. To his professional colleagues and clients and to his former students he was both "Professor Gaudin," their wise, inspiring, and enthusiastic teacher, and "Tony," their warm and beloved personal friend. Thus, his teachings and his unique inquisitive-creative approach to problems live on and grow in the accomplishments of his students. Antoine Gaudin was born at the turn of the century in Smyrna, Turkey, where his father was general manager of a French-owned railroad. It was there that he spent his earliest years, literally in the shadow of classic marbles from diggings at the site of Aphrodesias, which his father had rediscovered. From this, Tony developed an appreciation of the arts. He eventually surrounded himself with art treasures; he reveled in the beauties of nature, and he cherished his choice collection of rhododendron and azaleas. His artistic traits led him to take up painting when his daughter, Elinor, sought his help in blending her tints for a water color. In typical fashion he was not satisfied until he had become adept with pastels in capturing the muted tones of distant landscapes and the technical properties of light and color. Unfortunately not many paintings were produced. His paternal grandfather was Marc-Antoine Gaudin, for many years secretary of the Academie des Sciences in Paris, and a well known chemist and mineralogist whose primary interests included the synthesis of precious stones. In an autobiographical sketch written in 1939, Dr. Gaudin recalled: "As a child I saw many of the original synthetic sapphires and rubies which my father had inherited. This, coupled with my father's avocation of mining ventures and archaeology, early decided that I would become connected with the mineral industry." One can speculate that the archeological activities of his father, the mineral systhesis experiments of his grandfather, and his own early studies of mineralogy and geology formed a base from which his special talents as an experimentalist were to develop. Laboratory research under Professor Gaudin's personal guidance was often an intensive, fast- moving, and exciting experience--especially to a new graduate student. First of all, Professor Gaudin was a highly skilled observer with seem-

Jan 1, 1976

By Nathaniel Arbiter

The question of automation of concentrator operations with computer control is under increasing consideration. Some of the problems involved will be discussed from the viewpoint of the availability of the requisite, detailed knowledge of the unit operations. The justification for full-scale automation of a mill must ultimately be economic--an increase in profitability over and above the cost of instrumentation and development, Potential savings would be in three probable directions: decrease in operating labor costs by substitution of machine control; improved metallurgy through continuous effective control; and decreased operating costs by achieving higher unit capacities and process efficiencies.

Jan 1, 1962

By F. J. Sotillo

Mining in Peru is mainly concentrated on metallic and polymetallic ores of gold, copper, lead, zinc, silver, tin, iron, etc. However, little has been done to develop extensive and rich non-metallic or Industrial Minerals deposits with the exception of some silica and phosphate deposits. This paper presents the characterization and metallurgical studies for the development of a feldspar deposit. These studies showed that the special characteristics of the ore, such as high porosity, high Al2O3 content, low clays content, and sized material allowed us to obtain commercial products applying relatively simple and low cost concentrating unit operations. The characterization studies showed that the feldspar products contained no quartz and about 90% of albite (NaAlSi3O8). The 14x40-mesh size fraction product analyzed 5.91% Na2O, 22.56% Al2O3, 65.73% SiO2, 0.65% K2O, 6.50% CaO, and 0.40% Fe2O3; whereas, the 40x150-mesh size fraction product analyzed 6.22% Na2O, 24.30% Al2O3, 60.80% SiO2, 0.91% K2O, 7.06% CaO, and 0.54% Fe2O3. These products could be used for manufacturing glass, ceramics, refractory, and filters in different applications. In addition, Middlings, could be used as insulation material due to its porosity (bulk density of 0.828 Kg/dm3), analyzing 4.46% Na2O, 15.7% Al2O3, 67.2% SiO2, 2.57% K2O, 3.94% CaO, and 4.24% Fe2O3. The material showed a sphericity of 0.77, a roundness of 0.68, and acid solubility of 13.3025% on only washed and 2.72% effective for clean material suitable for use in these applications. No selective accumulation of the valuable mineral was observed at any specific size fraction. However, iron and titanium bearing impurities trended to concentrate in fine fractions (minus 70 mesh -212 µm-). Metallurgical studies demonstrated that this feldspar ore required sizing at 14x40 mesh and 40x150 mesh to render commercial products. In the case of the 14x40-mesh size fraction, the process involved magnetic separation, gravity separation, and flotation for feldspar (direct flotation) using a blend of primary and condensate amines. However, the reverse flotation for mica-biotite and iron bearing minerals was also possible using petroleum sulfonate. The metallurgical process for the 40x150-mesh size fraction required magnetic separation and reverse flotation of iron and titanium bearing minerals, the feldspar being reported in the sink material. Commercial products from this feldspar deposit for glass, ceramics, refractory, and filtration; and for the manufacturing of insulation material were obtained.

Feb 23, 2014

By Paul B. Queneau, Barry J. Hansen, D. Erik Spiller

Most lead and zinc secondaries are recycled pyrometallurgically. However, many problems encountered in secondary smelters have been solved by addition of physical concentration and/or hydrometallurgical processing steps, with resulting important environmental benefits. U.S. secondary lead and zinc operations are described, covering conventional smelters, EAF-dust treaters, and zinc sulfate/fertilizer producers, including plant capacities, technologies, and outputs. During the past two decades, remarkable advances have been achieved by recycling spent lead-acid battery components. Interaction between primary and secondary zinc producers, the fertilizer industry, and the zinc chemical industry has substantially decreased waste generation.

Jan 1, 1993

The Waste Isolation Pilot Plant (WIPP) is a geologic repository for disposal of transuranic waste and is operated by the US Department of Energy. The repository is located at a depth of 655 min the Permian age salt beds of the Salado Formation. The exhaust air from the facility is independently monitored by the Environmental Evaluation Group to verify compliance with regulatory release limits for radioactive materials. A May 1995 video inspection of the exhaust shaft identified fluid migration into the uppermost 25 m of the shaft. Since then, water has been observed flowing in from cracks in the shaft lining between 16and 25 m below surface level at an estimated rate of between 5 and15 m3/d. This water inflow has not only negatively impacted the equipment in the shaft, associated duct-work and monitoring equipment located at the top of the shaft, but also challenged efforts to verify compliance at the WIPP. This paper provides an analysis of these effects.

Jan 1, 2004

Mineral processes are relatively simple and metallurgical accounting would also be simple if it were not for the nature of the raw materials and the large scale of operations. Essentially the balance between input and output requires only weighing and assaying of the feed, salable products, and waste. but because of complexities to be described in the following pages there are few plants that do not encounter difficulties that cause some sacrifice of precision for economy and practicality. In arriving at a sound compromise, capable

Jan 1, 1985

By Jennifer Gallagher

The Henderson molybdenum mine, near Empire, CO, has operated since 1976 using a panel caving process and a rail haulage transportation system. After two decades of service, the rail haulage system required a substantial capital expenditure to improve operations. The timing for this worked well because Henderson was able to combine this capital need into a mine plan that addressed process bottlenecks and current mining practices as a new production level was designed and developed. This process was a logical step, following an equipment upgrade program, and became known as the Henderson 2000 project. One of the key components of Henderson 2000 is a new ore transportation system. Throughout Henderson's life, the bottleneck has been the rail haulage system. Henderson staff evaluated several transportation alternatives and decided on a truck haulage configuration feeding an underground crusher and conveyor system. This configuration will eliminate the haulage bottleneck and will allow the mine to increase capacity. The installation of this system will be completed by the year 2000. The second key component of Henderson 2000 is the development of a new 7175 production level to extract the lower reserves of the ore body. Henderson staff benchmarked other caving operations and compared their mining practices to Henderson's basic mining guidelines. It became apparent that Henderson's practices could become more efficient, particularly in the areas of drawpoint spacing and column heights. These concepts were incorporated into the layouts

Jan 1, 1998

By R. Riding

Degussa Corporation's peroxide-assisted leaching (PAL) process was evaluated in the batch concentrate leach circuit at Hecla Mining Company's Republic Unit. The product leached in this batch circuit is a high grade gold-silver sulfide (predominately pyrite) flotation concentrate. The primary objectives of the test program were to determine the effects of dilute hydrogen peroxide addition on leaching kinetics, sodium cyanide consumption and precious metals recovery. The results of the testing demonstrated that using dilute hydrogen peroxide produced the following benefits: - 1. Batch leach time requirements decreased by 80%. - 2. Sodium cyanide consumption in concentrate leach reduced by 55%, which translated to an overall plant reduction of 20%. - 3. In the concentrate leach process, gold recovery was increased by 1 to 2%. Because of the excellent metallurgical results achieved with the use of dilute hydrogen peroxide, as well as an economic incentive, PAL has become standard practice in the concentrate leach circuit operation. A complete description of the Republic PAL plant evaluation and performance is provided in this paper. In addition, process chemistry considerations in regard to the role of hydrogen peroxide are discussed.

Jan 1, 1992

By Donald E. Warnken

The Study concerns the estimation of fair market value (FMV) of non-producing mineral rights. Two approaches to value are used and the values determined by each are compared. The Study area environment is unusual. The tectonics is visible on surface rocks throughout much of the study area. The effect on mineral values in the exposed areas has been compared to areas where the tectonics is not visible.

Jan 1, 2005

By M. A. Reinsel

New technology for removal of nitrate from low-temperature waters has been developed. Typical results from the first operational-scale system (operating at a metal mine in Montana since January 1996) are over 90 percent nitrate removal at a flow rate of 130 gpm and a water temperature of 12°C. The system also operated successfully at flow rates as high as 300 gpm and water temperatures as low as 2°C. The ABC is advantageous because it is: a) cost-effective to design, construct and operate, and b) effective at cold water temperatures. The system can be designed for a variety of flows, nitrate concentrations, water temperatures and water qualities.

Jan 1, 1998

By M. A. Trevits

Methane gas is an ever-present problem facing the underground coal mining industry. Mine operators are mandated by law to maintain safe concentrations of methane gas within the mine environment. Ventilation is used by all mine operators to reduce gas concentrations. When gas emissions are such that ventilation alone cannot control the gas, methane drainage methods must be applied. In the 1970's, there was a concern that unprecedented gas emissions would be experienced as mine operators began new developments in the deep and gassy Blue Creek and Pocahontas No. 3 Coalbeds. Such concern was well founded as significant gas volumes are being emitted as these mining operations mature. In 1971, the O.S. Bureau of Mines began to tabulate and track the change in mine emissions. These data were extracted from the underground coal mine quarterly air quality-quantity inspections performed by the Mine Safety and Health Administration. At that time, approximately 6,560 Mm Id (231.7 MMcfd) of gas were emitted from 430 underground coal mines. It was determined however, that the mines emitting less than 2,832 m Id (100 Mcfd) contributed only 2.1 percent of the total daily gas flow. In 1988, underground coal mines emitted 8350 Mm Id (294.9 MMcfd) from 487 mines. This report evaluates the changing nature of U.S. mine gas emissions over the last 18 years.

Jan 1, 1993

By T. Carl Jr. Shelton

Surveying and mapping are used to locate and visually portray objects, lines, or areas in relation to a reference point or line. The actual making of the measurements to locate the objects and points falls under surveying while mapping is concerned with putting the survey information into a graphical form. Generally, the type or class of proposed survey depends on the precision required. Some surveys may need only approximate measurements which can be obtained by simply pacing or by using an ordinary measuring tape; others may require much accuracy, thus calling for the use of an engineer's transit or theodolite along with a graduated steel tape for horizontal measurements, or a level and a graduated rod for measuring vertical distances. Mapping is likewise dependent on accuracy requirements. For example, a general layout showing the relative position of surface facilities may not call for a large scale of dimension or great precision whereas for detailed work, a large scale plus care in plotting points and drawing lines and curves are important factors.

Jan 1, 1981