Search Documents

By K. W. Deter

The gold ores in the Jerritt Canyon district have been recognized as refractory since they were first encountered by FMC geologists in 1976. Upon obtaining managing rights as joint venture partner, Freeport McMoRan Inc. developed an operating plan featuring carbon-in-leach gold recovery techniques for the oxide portion of the ores and a patented sulphide oxidation step followed by chlorination for treating the organic carbon constituents of the refractory ores prior to CIL gold recovery. The plant was successfully started up in 1981 with the first gold poured on July 4, 1981. Initial plant throughput was designed to be 2495 MTPD (2750 STPD) total through the dual processing trains.

Jan 1, 1991

By Robert J. Timko, R. Lincoln Derick

This report presents a Bureau of Mines evaluation which examined the extent of gas leakage from sealed areas in underground coal mines and measured the effectiveness of commonly used structures for controlling the quantity of gas exchange from these areas. Evaluations were performed on five abandoned areas in two operating underground mines within the same coal seam. Methane and oxygen levels inby the seals were monitored to determine if the gas leakage was unidirectional or bidirectional. Results from this and prior work dealing with minimizing gas leakage were then applied to a newly abandoned area. Also discussed are bulkhead site preparation, construction plans, techniques for monitoring the status of the atmosphere within the sealed volume, and a modified European method for controlling gas migration from the sealed volume to the active mine.

Jan 1, 1991

By R. Simon

Strain-burst phenomena are generally characterised by sudden releases of energy in a volume of highly stressed rock. Strain bursts are encountered in situations such as crown pillar bursts during cut-and-fill mining, face bursts at development headings cord floor bursts in deep shaft sinking. This paper describes a simple two-dimensional linear elastic FE modeling approach that leads to the calculation of the energy-release rate (ERR) and the total energy storage rate (TESR) in the rock-mass around the openings. The merits of using such energy parameters in the analysis of strain-burst problems for identifying areas of high energy release/storage are discussed through a case stud v. However, much site-specific back analyses are needed to better understand how strain bursts and energy parameters are interrelated.

Jan 1, 1999

By L. F. Nicolai, W. J. Schlitt

Lateral migration of leach solution in heaps and dumps is attributed to two phenomena. One is site-specific anisotropic conditions that exist on a macroscopic scale on the surface or within the rock piles. The second is associated with a random walk phenomenon that causes dispersion of solution, especially at gradients in flow or hydrostatic pressure. The latter phenomenon is a general condition that will occur in any leaching operation. Its effects are modeled by computer analysis and are compared with available field data on heap leaching. Under appropriate assumptions, the observed 58° angle of solution dispersion can be reproduced by the model. The combined effects of both anisotropy and random walk are also discussed. Finally, the impact of lateral solution flow on actual leaching operations is considered.

Jan 1, 1988

By D. Baker

Alternative material handling methods are allowing material handling operations to be performed with increased cost savings. This allows for higher production levels with better returns. RAHCO International Inc.'s Continuous Mining Excavator (CME) has recently received a lot of attention due in part to its operating efficiency, flexibility, and associated low operating costs. The CME is designed to perform three primary functions. These include material excavation, sizing and loading operations. In many applications, a drilling and blasting process can be eliminated. The CME was developed originally in 1985 for open pit coal mining. See figure I. Since this time, it has been proven an effective system for excavating many other types of materials including friable and sticky materials. It has also been shown to suitably handle hard rock in certain site conditions.

Jan 1, 1998

By S. Mathur

Future Florida phosphate reserves contain higher MgO than presently mined deposits. The high MgO content is contributed by dolomite and Mg-rich clay, palygorskite. Selective flocculation was attempted to reduce the MgO content of apatite in synthetic mixtures of apatite with dolomite and palygorskie. Mixed mineral selectivity was predicted in the apatite-dolomite and apatite- palygorskite systems with Poly(ethy1ene oxide) (PEO) flocculant. Loss of selectivity in the mixed mineral systems was primarily attributed to heteroflocculation, which was minimized by addition of a Site Blocking Agent (SBA), a lower molecular weight fraction of PEO, prior to addition of the flocculant. A 80:20 mixture of apatite-dolomite (or palygorskite) was upgraded as 95% apatite at more than 80% recovery level in the product fraction.

Jan 1, 1995

By R. D. Miller, L. Schulte, J. Davenport, D. W. Steeples

Shallow seismic reflection methods were successfully used to delineate the subsurface extent of roof failure associated with the dissolution mining of a 120-m (400 ft) deep and 60-m (200ft) thick salt bed in central Kansas. Surface subsidence at North American Salt's Hutchinson, KS, salt-dissolution well field represents a potential risk to surface structures and transportation facilities. Three intersecting common depth point (CDP) seismic reflection profiles, targeting the subsurface around an actively subsiding sinkhole, possess sufficient resolution to delineate the horizontal and vertical extent of subsurface rock failure associated with the subsidence. The three seismic profiles showed a disturbed subsurface area 90 to 105 m-diam (300 to 350 ft-diam) at a depth of between 60 to 75 m (200 ft and 250 ft). Confirmation drilling verified the interpretation of the seismic data. The seismic reflection method has the potential to resolve disturbed subsurface areas greater than 23 m-diam (75 ft-diam) at this site.

Jan 1, 1994

By Gordon T. Austin

Garnet is the general name for a family of complex silicate minerals having similar physical properties and crystallizing in the isometric (cubic) system. All garnets have the same general chemical formula but vary greatly in chemical composition. The name garnet is derived from the Latin word granatus, meaning like a grain, which refers to the mode of occurrence wherein crystals resemble grains or seeds embedded in the matrix. GEOLOGY Mineralogy Chemical Properties: The general formula for garnet is A3B2(SiO4)3, whereas A can be calcium, magnesium, ferrous iron, or manganese, and B can be aluminum. ferric iron, or chromium, or rarely titanium. The formulas and names of common garnet species are: [ ] Almandite and almandite-pyrope solid solution garnets are the best abrasive types, but andradite, grossularite, and pyrope also are used. All species of garnet have been used as gemstones. The structure of garnet consists essentially of isolated SiO, tetrahedra connected by oxygen-cation-oxygen bonds through the distinct A and B group cation sites. Within this structure magnesium, ferrous iron, and manganese easily interchange and substitute for each other in the A cation position, and calcium does so less readily. Additionally, aluminum, femc iron, and chromium substitute for each other to a limited extent in the B cation position. This ability to substitute or exchange ions without changing the crystal structure is called isomorphism, and garnet is one of the finest examples of a isomorphous series. Because of this isomorphism there is complete solid solution between certain garnet species but not between others. Fig. 1 illustrates these solid solution relationships. Some rare species of garnet are known that illustrate the wide range of cation substitution that the garnet crystal structure can accommodate. They include: [ ] These rare species are not of interest for industrial applications, but can be of interest to mineralogists and the gem industry. Physical Properties: Garnet displays the greatest variety of color of any industrial mineral. Garnets have been found in all colors except blue. For example, grossularite can be colorless, white, gray, yellow, yellowish green, various shades of green, brown, pink, reddish, or black. Andradite garnet can be yellow- green, green, greenish brown, orangy yellow, brown, grayish black or black. Pyrope is commonly purplish red, pinkish red, orangy red, crimson, or dark red; and almandite is deep red, brownish red, brownish black or violet-red. Spessartite garnet can be red, reddish orange, orange, yellow-brown, reddish brown, or blackish brown. A few garnets exhibit a color-change phenomenon. They are one color when viewed in natural light and another color when viewed in incandescent light. Because of the great variation in color of garnet within each species and similarities in color between garnets of different species it is recommended that garnet identification not be based on color alone. The Mohs hardness of garnet varies from 6.5 to 9.0. Grossularite and uvarovite have a hardness of 6.5 to 7.5; andradite is 6.5 to 7.0; and pyrope, almandite, and spessartite are 7.0 to 7.5 in hardness. There are reports of almandite having a hardness of between 8.0 and 9.0. As with hardness, the specific gravity of garnet varies considerably. The specific gravity may be as low as 3.2 or as high as 4.3 depending on chemical composition. Garnet crystallizes in the isometric system with rhombic dodecahedra and trapezohedra the most common forms. Crystals also form in combinations of dodecahedra and trapezohedra or either of these in combination with hexoctahedra. Crystals can have cubic or octahedral faces, but these are rare. Under favorable conditions of formation garnet will crystalize in nearly perfect forms that rival study models. Garnet also forms as irregular blebs, grains, knots, or masses, with or without distinguishable crystal faces, and as coarse- or fine-grained granular masses that appear to be totally lacking in crystal form. The fracture of garnet also shows great variation. In some garnets, particularly those that are well crystallized and glassy in appearance, the fracture is subconchoidal to conchoidal. Other, more poorly crystallized garnets exhibit a fracture that can only be described as uneven. Garnet occasionally has an indistinct dodecahedral cleavage. Certain species of garnet from specific locations have a pronounced laminated structure consisting of planes of weakness along which parting takes place. This parting may resemble cleavage, but since it is mechanical and not related to crystal structure it is not true cleavage. The optical properties of garnet are sensitive to even small changes in chemical composition or strain in the crystal structure. For this reason each species does not have a single index of re- fraction (IR) but has a range of 1Rs. Uvarovite in its pure form should have an IR of 1.870, but in nature samples vary from 1.74

Jan 1, 1994

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

6.1 INTRODUCTION A surface structure will suffer damage when the additional stresses induced by ground deformations associated with surface subsidence, plus the original stress introduced by construction de¬sign, exceed the strength of the structural elements. In this con¬text, there are two methods available for preventing and control¬ling surface structural damage: one is to strengthen the structure and the other is to design the mining operations such that ground deformations at the structure site can be reduced to an acceptable level. Mining operations include panel layout and mining tech¬niques. These methods are detailed in this chapter. It must be noted that most prevention/control methods men¬tioned in this chapter are used in the countries where the reference papers are cited. In the United States, the coal operators are not required to take those measures mentioned in this chapter. Some of the methods described in this chapter cannot be implemented with¬out changes in the current mining practice as permitted by laws. In addition cost of implementing those methods are not considered here. 6.2 PANEL LAYOUT As shown in Figs. 2.9, 2.10, and 2.11, permanent ground deformations in a subsidence basin mainly concentrate near the edges of the underground opening, and can be divided into four zones. A structure located in different zones will be subjected to different types and magnitudes of ground deformations. In laying out the panels, Table 5.1 and Figs. 2.9, 2.10, and 2.11 could be taken into consideration. Attempts could be made to avoid placing the structure on a location where the ground deformation to which that structure is sensitive is at its maximum. Therefore rational design of the panel is the simplest way to reduce structural defor¬mations. Panel design involves the determination of panel dimension, panel edge location, direction of face advance, and use of yield chain pillars. A. Panel Dimension Since longwalls in the US employ a multiple-entry system, where rows of chain pillars are left unmined, subsidence over those chain pillars is usually smaller. Therefore, whenever possi¬ble, the panel dimension could be designed such that a major structure or structures are over those unmined chain pillars, be¬tween adjacent panels, or some distance beyond both ends of the panels. At the center of the supercritical final subsidence basin, a structure will not be subjected to any final or permanent ground deformations. In order to create such a condition, the panel width must be such that the structure will be located beyond the major influence zone of the final subsidence basin, the minimum dimen¬sion of which must be: [ ] where L is the width or length of the final mined out gob, t is the width or length of the structure to be protected, h is mining depth and [ ] s is the angle of full subsidence. B. Panel Edge Location Wherever there is a permanent panel edge, there are large ground deformations induced on the surface on both sides of the permanent panel edge. Therefore whenever possible the panel di¬mension should be designed such that the permanent panel edges could be located in the areas with the least impacts. In terms of permanent edge location, it is best to eliminate any permanent panel edge under a structure or groups of structures. If this cannot be done, the panel should be lengthened to reduce the number of permanent panel edges, or narrower multiple panels advancing in the same direction in a staggered manner could be employed. If the structures are located in Zones II and III, the longer dimension of the structure must be parallel to the nearest perma¬nent edge (Fig. 6.1). But in Zone IV, the longer dimension should be tangential to the corner of the permanent panel edge. If the structure is inclined to the permanent panel edge, it will be sub¬jected to twisting and shearing. C. Direction of Face Advance The direction of face advance should be parallel to the long axis of the structure. But if the structure is to be located at or close to the center of the final subsidence basin, the direction of face advance should be perpendicular to the long axis of the structure. Careful choice of the direction of multiple face advance is the most effective way to reduce structural deformation and thus dam¬age. This applies the principle of overlapping and cancellations of ground deformations, due to multiple face advance, at the right time and at the right intensity, e.g., opposing tilts, concave and convex curvatures, tensile and compressive strains are induced simultaneously on the structure to be protected by two or more faces. D. Use of Yield Chain Pillars In US longwall panels there are generally two or three rows of stiff chain pillars between the panels. The combined width of the chain pillars ranges from 100 to 350 ft(30 to 107m). depending on mining depth. In general, surface movement above the chain pil¬lars after the panels on both sides have been extracted is much smaller, as compared to that in panel center. Thus in order to create critical or supercritical width of opening and eliminate sur¬face bumps over the chain pillars, yield chain pillars may be em¬ployed (Jarosz and Karmis, 1986). However if yield pillars are to be used, it must be designed such that it yields totally right after the panels on both sides have been extracted. Unfortunately cur¬rent yield pillar design techniques cannot predict when and how much it will yield. In summary, whenever possible attempts could be made to lay out the panel in such a way that surface structures are located above chain pillars between panels or above solid coal beyond both ends of the panels. In those areas the surface structures will most likely be unaffected, or if affected, the damage is so minor that no remedial measures are necessary. 6.3 CONTROLLED MINING TECHNIQUES Several mining techniques are available for reducing the sur¬face ground deformations of specific types. Regardless of tech-

Jan 1, 1992

By I. H. Keith

INTRODUCTION The following papers describe the extraction of nickel in the form of ferronickel from the Dominican laterites. The Falconbridge process was developed initially in the Falconbridge Metallurgical Laboratories and subsequently in several successive stages of pilot plant operation in the Dominican Republic. In the course of this work we came to believe that there is advantage in piloting on site. Mining, metallurgical and geo-political considerations all have major impact and that belief has been borne out by commercial plant experience. Lateritic nickel ores differ substantially, even within the same orebody, in their amenability to extraction methods. The Falconbridge process takes account of the heterogeneous nature of the deposit. Three years of geological field exploration led to ten years of process development after it was realised that the then known metallurgical processes would not give economical extraction from the Dominican ores. In addition to establishing the viability of a novel pyrometallurgical approach, it was necessary to verify design parameters for a very considerable scale-up to prototype commercial operation. The plant was eventually constructed within the original estimates of time and cost. Unique features contributing to the technical and commercial success of the project are described. Additionally, some bold extrapolation based on pilot plant work, eventually proved to be quite conservative. The mine is not a conventional open pit operation, but is perhaps better characterised as an earth moving job. Novel application of mobile equipment led to great flexibility in the mine, where operation of several mining fronts is essential to maintaining uniformity of ore feed to the plant. The practical aspects of almost total acceptance of the oversize run-of-mine material through a high-capacity unit,

Jan 1, 1979

By Z. J. Hladysz

The Hladysz Rock Tester was developed at the South Dakota School of Mines as a portable rock strength tester. The hand held device is placed against a rock surface and struck by a hammer. The impacted force causes a steel ball in the device nose piece to indent the rock and simultaneously indent a standard steel bar also contained in the nose piece. By comparing the two indented diameters the compressive strength of the rock can be calculated using laboratory determined correlation coefficients.

Jan 1, 1984

By Edie Trimmer

Utah statute defines sovereign lands as "those lands lying below the ordinary high water mark of navigable bodies of water at the date of statehood, and owned by the state by virtue of its sovereignty." The lands within the bed of Great Salt Lake (GSL) are, by this definition, sovereign lands, acquired at statehood in 1896 in accordance with the "equal footing" doctrine, granting each state control and ownership of navigable waters and the lands underneath those waters within its borders. Under public trust doctrine, the state, as trustee for the people, bears responsibility for preserving and protecting the right of the public to use of the waters for navigation, commerce, fishing, recreation, and wildlife habitat. Also by statute, sovereign lands are defined as "state lands," to be managed by "multiple use sustained-yield principles." The Division of Forestry, Fire and State Lands is given management authority for sovereign lands and, as manager, has responsibility to prepare comprehensive plans, initiate studies of the lake and its resources, implement comprehensive plans through state and local entities, and coordinate the activities of various divisions within the Department of Natural Resources (DNR). The Division of Forestry, Fire and State Lands also has responsibility for management of mineral leasing on sovereign lands. The many resources on the lake--water, minerals, wildlife, recreation, archeological and historical values--are managed by as many state agencies which occasionally creates conflicts. The brines of GSL contain several ions that crystalize into valuable minerals during evaporation. The major ions in the lake are, in order of relative abundance, chloride, sodium, sulfate, magnesium, and potassium. Mineral products which are currently extracted from lake brines are sodium chloride, magnesium chloride brine which can be sold as flake magnesium chloride or further processed into magnesium and chlorine gas, and potassium sulfate. Mineral products which have potential for extraction include gypsum, sodium sulfate, and trace amounts of lithium, boron, and bromine. The GSL contained an estimated 4.3 billion short tons (st) (3.9 billion metric tons [mt]) of dissolved salts in 1998. Utah Geological Survey (UGS) estimates of the dissolved salt content in GSL have fluctuated from 4.0 to 5.5 billion st (3.6 to 5.0 billion mt) due to the dynamic conditions in the lake as salts are precipitated and redissolved, and due to the diversion of brines from GSL, such as the West Desert Pumping Project. The lake has four areas of varying salinity, separated by dikes or other man-made structures: north arm and Stansbury Bay brines at near saturation (25 to 27 percent total dissolved solids [TDS]); the main body of the south arm with concentrations ranging from 7 to 15 percent TDS as lake elevations fluctuate; the waters in Farmington Bay at approximately 3 to 5 percent TDS; and Bear River Bay at <1 to 7 percent TDS. The percent TDS in Bear River Bay fluctuates with lake level, and changes in Bear River inflow. The transfer of salts from the south arm to the north arm has raised questions about the viability of the mineral and brine shrimp industries. The UGS and the U.S. Geological Survey (USGS) continue to monitor salinities at designated sites on the lake to document changing lake salinity. A recurrent theme is that placement of dikes and diversions can have significant and rapid impacts on various conditions in the lake. Hydrocarbon resources on the lake are significant, but presently undeveloped. The hydrocarbons are low gravity (4 to 9 degree API) and tar-like, contain high nitrogen concentrations, and up to 12 percent sulfur. The unusual characteristics of the oil have been the subject of studies by chemists at Weber State University and University Louis Pasteur de Strasbourg. However, these resources are difficult, and at present, uneconomic to extract using current technology because of the nature of the hydrocarbons, and production in "an offshore, highly saline environment." Oolitic sand deposits make up many of the beaches and shorelines around the lake. Because of their high calcium carbonate content, oolites have been used by Magnesium Corporation of America (MagCorp) and its predecessors for acid neutralization and dike construction. Oolites are also used in very minor amounts in flower drying. The Utah Division of Oil, Gas and Mining reports up to 130,000 st (118,000 mt) mined annually by MagCorp from U.S. Bureau of Land Management (BLM) lands adjacent to GSL. Currently, there are twelve producing mineral leases which generated slightly more than $1,000,000 in royalties during calendar year 1998. IMC Kalium Ogden Corp. (IMC Kalium) produces potassium sulfate and magnesium chloride from brines concentrated through solar evaporation in Bear River Bay and Clyman Bay. By-product sodium chloride is transferred to IMC Salt, which packages and sells the salt. MagCorp produces magnesium metal from brines concentrated in Stansbury Bay. Cargill Salt produces sodium chloride from brines provided by MagCorp under a lease agreement. Morton Salt produces salt at the southeast end of Stansbury Island. Lastly, North Shore Limited produces cocentrated brines for use in dietary and mineral/vitamin supplements near Spring Bay in the north arm of the lake. Producers of magnesium, potash, and salt from GSL contribute significantly to the value of metals and industrial minerals in Utah. Together these companies contribute approximately $240 million in gross value, or 18 percent of the value of the state&apos;s nonfuel mineral production. Most of this production is exported.

Jan 1, 2001

By Richard Jr. Ray, Richard Druesedow

The Virginia Operations of Consolidation Coal Co. include a diversity of mine fan configurations which have been tested to quantify pressure losses through the inlet ductwork. Airflow and pressure measurements were taken at four shaft sites to calculate losses for the 90-degree bend at the top of the shaft and the self-closing dampers or closing doors located between the shaft and fan. Velocity contours were then developed from the test data to determine flow patterns in each fan system component. In addition, yaw and pitch angles of airflow through the fan annulus were measured to evaluate turbulence levels created by various inlet ductwork designs. The test results indicate that proper design of the shaft collar and ductwork arrangement for main mine fans can substantially reduce system pressure losses and air turbulence. BY minimizing the pressure drop experienced on the surface, these design improvements enable the bulk of the total pressure developed by the fan(s) to be utilized in the mine.

Jan 1, 1995

By Robert W. Bartlett

Both hydrometallurgical and vapometallurgical processes often involve ores that have been previously ground and size classified. When the valuable mineral is substantially liberated, the chemical reaction is likely to occur on the particle surface and the particle core will shrink as the reaction proceeds. If the chemical reaction products are solid materials then a solid shell, usually porous, will form around the shrinking core. This is known as the core/shell or topochemical reaction model. Using a spherical approximation for the particles, equations have been developed to express the extent of chemical conversion of the particle, depending on which one of the following process or mass transport steps is rate controlling:1 (1) chemical reaction at the particle surface, (2) diffusion through the thickening reaction product shell or (3) mass transport through a boundary layer surrounding the particle. In a previous paper2 these equations were coupled with the Gates -Gaudin-Schuhmann equation 3 4 describing the distribution of particle sizes resulting from comminution of rocks and other brittle solids to develop reaction yield curves expressing the weight fraction of metal or other valuable component of the feed that was chemically converted as a function of residence time. This was done for (a) batch, (b) continuous plug flow and (c) continuous back-mix flow (continuous stirred tank) reactors or process vessels. To make the curves of general rather than special utility, the residence time (average residence time for back-mix reactors) was normalized to a dimensionless time by dividing by the time required to completely chemically convert the largest particle in the feed to reac-

Jan 1, 1972

By Donald Whittaker

Severe climatic conditions in mines are normally associated with working at depth. More precisely, it is a matter of working in regions of high strata temperature, since, for example, some coal mines in the Ruhr have strata temperatures at 1000 m which are matched only at 3 times that depth in the South African gold mines. In Britain we are perhaps fortunate in encountering strata temperatures in our deeper coal mines some 10-15 K lower than at the same depth in the hot mines of the Ruhr. Nevertheless the problems of high temperatures and humidities in UK mining operations, which in the past have been confined to a few specific sites, have in recent years become more widespread, and there is every reason to suppose that the trend will continue. Clearly strata temperature is not the only .causative factor. Long ventilation circuits serving districts remote from the shaft must also play a part, while the heavy use of machinery and the rapid, rates of excavation of modern mining methods are obviously important. It is necessary to understand the mechanisms of all such factors, and to measure their magnitudes and fluctuations, if remedial measures are to be properly designed or predictions made which are accurate enough to be of use in ventilation planning. This paper presents the results of a long-term (and continuing) investigation carried out in several mines to measure the major sources of heat and moisture on longwall districts and trunk conveyor roadways. The variation with time of these sources is reported, and the resultant effect on the climate is considered. In their investigations of the heat exchanges occurring in a whole mine Oakes and Hinsley (1955-56)1 listed and estimated the magnitudes of a large number of heat sources. Some of these, namely autocompression of the air in the shaft, diesel engines and compressed air mains, do not apply to the present investigations, which refer to longwall districts with conveyor transport and no compressed air supply. Others, such as oxidation of coal and, desorption of methane, have not been taken into account in the measurements, but are discussed later. One other source, the importance of which was pointed out by Gracie and Matthews (1975)2, is the coal on the conveyor, a form of strata heat emission, but one which is strongly dependent on the rate of coal production. The heat emissions measured in the present investigations were the energy consumed by electrical machinery, the heat conducted from the strata and the heat lost by the conveyed coal. Most of the emitted heat was removed from the district by the ventilation air, and was measured by continuously recording the enthalpy of the air at fixed stations. The heat removed by service water, supplied for machine cooling and dust suppression, was also measured. Account was of course taken of the relatively minor changes in level around the districts, in terms of the potential energy gained or lost by the coal and by the ventilation air (autocompression).

Jan 1, 1980

By G. Zandt, H. R. Pratt, W. A. Hustrulid, M. Bouchon, D. E. Stephenson

PREFACE The National Waste Terminal Storage Program was initiated to conduct the research to select a site for the disposal of high level radioactive waste in deep geologic formations. As part of this program, the Savannah River Laboratory at Aiken, South Carolina, is conducting geologic research of generic applicability on the potential subsurface damage to a repository from an earthquake. Part of this study involved the collection of data on subsurface damage due to an earthquake, and another part involved the calculation of displacement fields as a result of an earthquake. Both of these studies were conducted at Terra Tek of Salt Lake City. This report is an abridged and combined version of both studies which was presented at the Rapid Excavation and Tunneling Conference in Atlanta, GA, on June 19, 1979.

Jan 1, 1979

By Majid Ataeepour, Ernest Y. Baafi

High level programming languages such ass C, FORTRAN and BASIC have been used in the mining industry to simulate truck-shovel systems. In addition, some special languages for simulation such as GASP, GPSS, SLAM, PROOF and SIMAN are commonly used. The most recent simulation system ARENA uses graphical modelling approach as well as animation notion. In this paper, the main elements of ARENA required to perform a truck- shovel simulation and to view the simulation results by means of the model animation are presented. The layout of the haulage system including shovels, trucks and dump sites was generated using draw tool in ARENA. All the components of the haulage system were represented by graphical modules. Animation tool was used to depict the performance of the haulage system as the simulation progressed.

Jan 1, 1996

By Guillermo V. Borquez

The economics of open pit mine design are dictated by three basic elements: cut-off grade, stripping ratio and slope angle. Although these elements are functions of a number of independent parameters, they are interrelated through their influence on the overall economics. The optimum slope angle is the most uncertain element to determine, because rock mass properties are difficult to obtain. However, for preliminary estimation, the slope angle can be determined from the relationship between the probability of failure and the safety factor. The economics of the slope selected will depend on a profit versus risk judgment. In this paper, the author will present an actual case of application of this postulate.

Jan 1, 1977

By M. Deutsch

A common casualty of modern open pit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can really be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period. And grade control polygons may be ragged, narrow, and not minable with realistic equipment. In this paper all of these problems are addressed by encoding these three fundamental open pit mine optimization problems as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are non-linear and may guarantee the optimality that metaheuristics cannot. INTRODUCTION Open pit mines are large and complicated operations, which require significant initial and ongoing investment. A single mine may employ hundreds or thousands of people and creates substantial benefits for both the surrounding and global communities. Planning an operation of this magnitude requires a lot of effort and cannot be done optimally by hand. Mining engineers today rely on many techniques from operations research to guide decision making, and to maximize the value of the mine. Techniques including linear programming, metaheuristics, and network algorithms are all used to solve different problems throughout mine design and optimization. However, techniques based on Boolean satisfiability, including the optimization extension of maximum satisfiability, have not seen much use in mining despite being used in many other fields including electronics design, scheduling, and artificial intelligence. We claim that maximum satisfiability is a useful and meaningful way of expressing and solving optimization problems in mine planning. However, this technique does not come without challenges; the problem is NP-hard, and modern techniques for solving these problems can struggle with the number of variables and clauses that a typical mining problem requires. Also, some of the constraints that mining must contend with do not fit nicely into the satisfiability paradigm. Despite these challenges, we believe that maximum satisfiability provides a useful framework for considering operational constraints and expressing some problems that other techniques can't easily express. Maximum satisfiability can be solved exactly, yielding the true optimal answer which metaheuristics cannot guarantee. In this paper we show the applicability of maximum satisfiability to mining by specifying three fundamental problems in open pit mine optimization. We show how these fundamental problems can be formulated and how they can be extended within the framework of maximum satisfiability. For the remainder of the paper we first give a brief background on common elements between the three problems and an introduction to satisfiability. Then we tackle the three problems; the Ultimate Pit Problem, the Block Scheduling Problem, and the Grade Control Polygon Problem. In the Ultimate Pit Problem we specifically show how to extend the problem to support a minimum mining width – a coveted result for many mining engineers. We then discuss some of the complexities and shortcomings of this framework and possible research directions.

Jan 1, 2019

Interstate 70 running into the mountains west of Denver, CO is the main access to the state?s numerous ski areas and other tourist attractions. As such, the highway is a vital part of Colorado?s economy. Due to the mountainous terrain in which it winds, I-70 is limited to two lanes in either direction. And, during the past few decades, the volume of traffic has increased to the point where motorists encounter major delays, particularly on Friday evenings and Saturday mornings heading west from Denver, and then again on Sunday evenings heading east. In the past, those delays occurred mostly during the ski season. However, many of the mountain towns have been successful in turning their resorts into year-round vacation destinations. A good move economically, but the pressure added to I-70 has caused even greater traffic delays, sometimes to the point where some Front Range residents avoid trips to the mountains.

Jan 1, 2013