Search Documents

This paper reports on the behavior of mercury and its compounds during the thiosulfate leaching and recovery of gold. Thiosulfate solutions are shown to dissolve Hg0 and Hg2Cl2 to a similar extent as cyanide, but the leaching of HgS is significantly slower in thiosulfate solutions compared to cyanide. Hence, the use of thiosulfate may be an option for treating ores containing high levels of cinnabar, especially since the legislation concerning the discharge or sale of mercury is becoming more restrictive. The deportment of mercury during gold thiosulfate loading and recovery using a strongly basic anion-exchange resin was also studied. Although the mercury thiosulfate complex loads on the resin, the adsorption is weaker than for gold, with an equilibrium constant between gold and mercury of 51. Resin loaded with gold, mercury and copper was pre-eluted with thiosulfate (to remove copper) and eluted with a chloride and sulfite eluant. The majority of the mercury is eluted by the eluant and, hence, its deportment closely follows gold and the eluate would need to be treated to remove either mercury dur-ing or prior to gold electrowinning.

Jan 1, 2010

By Greg Sanders, Bill Lueck, Michael Gilbert, Mahmood Khwaja

"The city of Minneapolis contracted with CDM Smith to update and provide a conceptual design for improvements to mitigate surcharge flooding in the Central City Storm Water Tunnel System (CCSTS). As a part of the project, CDM Smith conducted a field survey and condition assessment of the existing tunnel system. Information from the survey was then used to update the existing XPSWMM model and develop system wide alternatives.The CCSTS provides storm-water runoff drainage for nearly the entire area of the city’s downtown commercial district. The system consists of deep storm-water tunnels constructed in the St. Peter Sandstone, approximately 21 m (70 ft) below the street’s surface. The primary tunnels comprising the Central City storm water tunnel system are located below Hennepin Avenue, Nicollet Mall, Lesalle Avenue, Marquette Avenue South, 2nd Avenue South, South 5th Street, Washington Avenue South, Portland Avenue South, 2nd Street South, and Chicago Avenue South, as shown in Fig. 1. This network of tunnels conveys the runoff from a 305-acre tributary area that is generally bound by Hennepin Avenue and 1st Avenue North to the east, 12th Street to the south, 4th Avenue South and 7th Avenue South to the west, and 2nd Street South. These tunnels were constructed between 1936 and 1940, except for the Marquette Avenue South tunnel, which was constructed between 1963 and 1964.The CCSTS operates as a gravity flow system. These tunnels were constructed within the St. Peter Sandstone layer of bedrock and emerge from the bedrock at the Mississippi River below St. Anthony Falls. The Central City and the adjacent Chicago Avenue tunnel system converge into a single outfall at the Mississippi River. The runoff discharges from the converged outfall to a side channel of the Mississippi River, called a tailrace, located near the Guthrie Theater. The Minneapolis Division of Surface Water and Sewers provided 32 historic plats detailing the plan and profile of the tunnel system.The tunnel plans show nine different cross-section configurations. Eight configurations within the overall system generally show the same geometric “cathedral” shape with the inside dimensions varying from 1.2 to 1.8 m (4 to 6 ft) in width and 1.8 to 2.4 m (6 to 8 ft) in height. For analysis, these eight configurations were reduced to three configurations with regards to tunnel liner, cross-sectional area and support. For simplicity, the three configurations are described according to the three types of tunnel support used during construction: none required, light timber and heavy timber"

Jun 1, 2019

By David J. Barr

Public Law 91-190 - January I, 1970 states that, "The purposes of this Act are: To declare a national policy which will encourage productive and enjoyable harmony between man and his environment; to promote efforts which will prevent or eliminate damage to the environment and biosphere and stimulate the health and welfare of man; to enrich the understanding of the ecological systems and natural resources important to the Nation; and to establish a Council on Environmental Duality." The administrative aspects of this National Environmental Policy Act of 1969 have in essence established the requirement that all agencies of the Federal government assess the consequence of their actions with an Environmental Impact Statement. Furthermore, five states have already enacted environmental legislation, and others will surely follow. The Environmental Services Project Director for Dames and Moore has stated in the June issue of that company's publication, "Elements," that, "The nuclear power industry has perhaps been most affected to date by the Act [NEPAL but recent court decisions, legislative trends and general public concern will accelerate the spread of the Act's impact on other industries. Mining and petroleum are already involved in environmental affairs." There can be little doubt that within a very short time all environmental aspects of the minerals industry will be strictly regulated and monitored by some agency of Federal and/or state government. Indeed, it is probable that any future effort to extract natural resources will be contingent upon a favorable review of an Environmental Impact Statement. It is also quite possible that continuation of present operations will have to be justified on the basis of proof of an acceptable environmental impact. It is the objective of this paper to present some ways in which remote sensing technology can be applied toward an efficient collection of environmental data necessary for the preparation of an Environmental Impact Statement.

Jan 1, 1972

By Allegra Yeley, Ted Klemetti, Gamal Rashed, Tim Miller, Nicole Evanek

In 2015, the Subtropolis Mine in Petersburg, OH, experienced a massive ground collapse that continues to grow over time. Horizontal stress effects have affected the roof at this operation in the past and may have played a large role in this collapse. Horizontal stress can impact the roof and floor stability and endanger the health and safety of underground stone miners. Mines experiencing damaging effects from horizontal stress typically find that the principal stress direction is the same throughout the mine and the region. At the Subtropolis Mine the principal horizontal stress direction appears to change as conditions change and differs from the regional horizontal stress, particularly near the collapse or other roof fall areas. The growth over time of this collapse and other roof falls have been captured and analyzed using geologic mapping, 3D LiDAR scanning, numerical modeling and geographic information systems like ArcGIS. Utilizing these tools to better understand sitespecific conditions can be critical to reducing the potential of massive ground collapses in the underground limestone industry.

Feb 1, 2024

By O. Salami, G. Xu

Fire accident is one of the most classic safety concerns in underground mines both in the USA and abroad. It may occur from pool fires due to leakages in hose or pipes, vehicle fires, or fires in tires and conveyor belts in the underground mines. It may also result from the storage of flammable materials such as gasoline, diesel, and explosives in the underground. When fire occurs in an underground mine, it releases heat, smoke, and other toxic gases such as carbon monoxide, and methane to the surrounding thereby making life unbearable to the miners. Furthermore, smoke greatly impact visibility in the underground which makes evacuation even more onerous and challenging. To this end, a thorough investigation of fire behavior and spread of toxic gases in a practical underground mine is imperative to develop a reliable emergency evacuation plan in an event of fire disaster in the underground mine. The objective of this study is to investigate temperature variation and CO spread along mine airways by conducting full-scale fire experiment in the underground mine. The results presented from this study are crucial to developing evacuation plans in underground mines. In addition, the findings from this study could be used to validate existing evacuation models.

Mar 2, 2022

By Anthony D. Hammond

Geographic Information Systems (GIS) are powerful analytical and data display tools for mining industry management, capable of linking spatial features with tabular data and integrating communications across departmental boundaries. This GIS application concentrates in four technical areas of underground mining: ownership and mineral claims; exploration management; production; and mine safety. GIS provides land and exploration managers with the ability to consolidate and archive claim data and to georeference property maps defined in local coordinates into world coordinate systems. It facilitates optimal siting and querying of service installations and refuge chambers relative to production centers. GIS's proximity analysis identifies areas of potential safety concern and points to and maps the shortest routes to emergency exits, facilitating the prompt evacuation of mine personnel.

Jan 1, 2002

By Charles A. Maliszewski, James M. Galvin, Gerhard Urschitz

With obvious signs of deterioration, the double track, historically registered Bergen Tunnels as part of the commuter rail system in New Jersey waited for rehabilitation for a long time. Serious water in filtration not only caused operational and safety hazards for the electrified rail line but also deteriorated and structurally compromised the tunnel lining. An innovative rehabilitation program was developed to enlarge the tunnel and to provide a new waterproofing system and final lining. For the rock excavation and support New Austrian Tunneling Method (NATM) principles were utilized, while water tightness was achieved by installing a PVC membrane waterproofing system followed by a reinforced cast-in-place final lining. Experienced on-site supervision generated additional savings during construction by streamlining support elements based on geologic conditions encountered.

Jan 1, 2003

By Ralf Vergeiner

The most famous landmark of the city of Graz (Austria) is the clock tower on the castle hill. An underground chamber was built as a multifunctional structure beneath this landmark. The required structure was designed as cavern. The overburden to the clock tower in the north side of the cavern was only 30 m. To allow access from the city to the chamber and the clock tower, a vertical shaft was built near the cavern. Rock excavation was by drill and blast method. The pilot shaft was made by the raise-boring method. Because the location of the building site was in the center of Graz, special care was taken to minimize deformations and vibrations so as to protect surrounding buildings.

Jan 1, 2001

By A. L. Hinde

Ideally, mill circuits should be controlled so that excessive random disturbances are reduced in frequency and amplitude. It is difficult to derive an objective measure of the effectiveness of any chosen control strategy. Often, the response of the circuit to pulse or sinusoidal disturbances is used as a measure of the effectiveness of control, but this is not adequate in many circumstances because such disturbances bear little resemblance to those that occur in practice, and such an approach cannot be easily related to the profitability of the reduction process. A superior approach appears to be the application of the theory of stochastic processes. This theory permits both real process disturbances to be modelled accurately, and useful objective functions for control to be derived. A test of the usefulness of stochastic theory in mill control was made on the gold ore milling circuit shown in Figure 1. This circuit was fed with an ore which had a liberation characteristic such as that shown in Figure 2. It is simple to show that, for such a liberation characteristic, the recovery of valuable mineral will vary as the standard deviation of the particle mass-size distribution varies even though the mean particle mass-size is kept constant. Similarly it may be shown that excessive perturbations in the circulating load in a milling circuit such as that shown in Figure 1 can affect liberation. Figure 3 shows how, as the cyclone feed density increases and the sump water addition decreases at constant sump level, the cyclone operation becomes unstable and the discharge "ropes? with a consequent catastrophic coarsening in product size. By minimising the variance of the circulating load it is possible to reduce the probability of initiating instabilities of this nature.

Jan 1, 1977

By Robert L. Runkel, D. Kirk Nordstrom, James W. Ball

Low-flow reactive-transport processes in Wightman Fork downstream of the Summitville Mine, south-central Colorado were simulated using the OTIS and OTEQ solute-transport models. The simulation was calibrated using data from a synoptic study conducted during October, 1998. Discharge over the 8-km reach from just below the mine site to the Alamosa River confluence ranged from 0.077 to 0.17 m3/s; travel time was 10.7 hours; pH ranged from 4.6 to 5.7. Simulations revealed that mass balance for SO4 was maintained, and that pH, Fe, and Al were non-conservative. Simulations allowing hydrous ferric and aluminum oxide or hydroxysulfate precipitation matched observed water quality conditions more closely than simulations without precipitation.

Jan 1, 2000

By M. V. K. Reddy

A differential flotation process for recovery of molybdenite from chalcopyrite concentrates produced at Rakha Copper Concentrator, Bihar, India has been developed. The flowsheet is simple, and relatively inexpensive and yields a concentrate assaying not less than 45% Mo at a recovery of minimum 65%, starting from chalcopyrite concentrate assaying 0.4% Mo. The consumption of the main depressant used, sodium sulphide is not more than 25 kg/t of copper concentrate processed without steaming; and with steaming the consumption was brought dorm to less than 12 kg/t of concentrate. Further reduction is possible by optimization of steaming parameters. Based on laboratory experimental results, further tests were conducted on concentrator site and process design parameters were established for design of commercial plant.

Jan 1, 1982

By W. C. Smith

Even with the most conservative mine plan, rib instability can occur unexpectedly, and if not adequately dealt with, can progress from a nuisance to a major safety hazard. This Bureau of Mines paper examines the mechanisms of progressive rib failure in high mine openings and discusses techniques to control rib slabbing. A field test site in a longwall mine was instrumented to investigate rib behavior during mining. While data analysis showed minor pillar dilation, sporadic zones of progressive rib instability were detected which culminated in eventual rib failure. The failure occurred despite conservative pillar dimensions and shallow depth. Physical and computer models were used to demonstrate the mechanisms of rib failure and then evaluate the influence of support and other mine-related parameters on rib behavior.

Jan 1, 1989

By Richard C. Harris

Substantial economic benefits exist today for fine coal preparation and improved technologies coupled with more stringent air quality standards should increase those benefits in the future. The costs of cleaning can be determined with reasonable certainty with proper consideration given to mining methods, plant feed characteristics, refuse disposal and marketing impact. The benefits cannot be as accurately determined but include impact on generating capacity, plant maintenance, emission standards, slagging, fouling, transportation, and handling. Site specific cleaning offers particular benefits in some situations to tailor the preparation plant facility to boiler characteristics. Improved communications and methodologies need to develop to allow the coal producer and the coal user to clean coal to the degree that results in the lowest overall cost for electrical generation.

Jan 1, 1988

By R. Corriveaau

This paper is about a horizontally curved conveyor, which carries 6,050 stph of limestone over land from a new quarry to the owner's plant. The conveyor is 5,012 ft long with a horizontal curve radius of5,OOOft Site conditions made a curved conveyor design the most optimal and economic solution. Using our unique custom conveyor calculation program, TKRI was able to accurately model and design the conveyor to properly track the belt and prevent any spillage through the horizontal curve radius. A data monitoring system was installed that allows monitoring of the conveyor both locally and remotely. The remote monitoring allows TKRI to contact the owner for preventive maintenance. Preventive maintenance can reduce the conveyor downtime during normal operating hours.

Jan 1, 2004

By Irwin R. Higgins, Joseph C. Milbourne

The selection of a suitable nitrate removal process depends on a variety of site-specific chemical and environmental issues. The dominant technologies for nitrate removal include biological denitrification and continuous countercurrent ion exchange. The decision to apply either of these technologies, or both together, depends on the nature of the waste water to be treated. Factors that affect the selection of the biological system include the feed composition and feed temperature. Ion exchange nitrate removal systems ere less sensitive to the feed composition but require disposal or destruction of the concentrated pregnant eluate. The paper discusses Tetra's continuous countercurrent ion exchange technology (CCIX™) and fixed film biological reactor, Denite®. The treatment of the ion exchange pregnant eluant is also discussed.

Jan 1, 1995

By St. E. Deák

There is a large preoccupation concerning the development of expert tools (ET) in the mining industry, in order to minimize the impact from waste dumps and processing residues on the environment. In this paper, the authors present a new approach for the development of an expert tool for each area under study, in order to minimize production and disposal of mining wastes on the environment, by taking into account the DKRControl method as well as the Ecomining principles, regarding among others hazard identification, impacts and monitoring. Due to the complexity of this topic a reliable ET requires input from a number of interested stakeholders. The design and management of a mining waste disposal site over its entire life cycle is also considered very important.

Jan 1, 2008

By Wilson Blake

A mathematical model based on the finite element method of stress analysis has been used to describe the behavior of the western wall of the Kimbley Pit as its slope was steepened from 45 degrees to 57 degrees. Theoretical stress changes because of slope modification are slight except at the toe of the modified slope. Magnitudes of stress created are small when compared with the strength of a competent rock. Resulting displacement patterns point out the need for determining the in situ state of stress at a site prior to excavation or modification. A comparison of model results with field measurements shows that, in general, the model has described the measured behavior of the west wall of the Kimbley Pit remarkably well.

Jan 1, 1968

By M. Rodgers

Dow Water & Process Solutions (DW&PS) was approached by ASARCO Inc. to attempt to recover cobalt and copper from their copper solvent extraction (SX) raffinate. Cobalt is added to many copper electrowinning tankhouses to help to prevent lead electrode corrosion. With cobalt?s high price this can be a large expense. ASARCO has ore that contains a small amount of naturally occurring cobalt. Currently they have no way of capturing this high value metal from their leach or raffinate streams. DW&PS has some chelating resin technologies that should be able to help solve this problem.

Jan 1, 2010

By Amri Priambodo, Ian Leslie, Valérie Laflèche, Agustina Ratnaningrum, Robin Paine, Andrianus Sinaga, Willem de Beer

Freeport Indonesia consists of surface, civil and underground mining areas exposed to numerous geotechnical risks and hazards. PTFI uses various monitoring systems (Micro-Seismic, Firefly Light System, Mira Geoscience machine learning, etc.) to effectively manage these risks. The significant volumes of data from these sensors must be integrated into actionable information to provide the expected risk management. This occurs at the GeoEngineering Integrated Monitoring Centre (GIMC), a centralized department within the GeoEngineering Division, tasked with the responsibility to manage all geotechnical monitoring systems. The main hazard the GIMC is responsible for managing in real time is mine seismicity within the underground mining areas and the potential impacts on safe operations. Seismic system engineers achieve this objective through 24 hours a day and seven days a week operations of the GIMC, providing a centralized point of communication, alerts, evacuations and control during seismic events and emergencies. This paper will describe how the GIMC achieves its goal using reliable procedures and strategies based on detailed Triggered Action Response Plan (TARP), concise communications, novel technologies (FireFly Lighting System), and proven seismic re-entry programs to manage risk within the underground mining operations. The integration of geotechnical monitoring and reporting into a centralized group has improved the effectiveness and management of seismic risks and hazards at PT Freeport Indonesia (PTFI) mining operations.

Apr 26, 2022

By Taekhee Lee, Steven Mischler, Shawn Vanderslice

Diesel-powered equipment is widely used in the underground mining industry and their popularity results from properties including efficiency, versatility, reliability, and durability. In the U.S. approximately 7,700 diesel engines were used in 177 underground metal and nonmetal mines as of 2005 [MSHA 2005], and these numbers have likely increased since that time. Diesel engines have been shown to be a major contributor to submicron carbonaceous, respirable, and total particulate mass in the air of underground metal mines [Zielinska et al. 2002, McDonald et al. 2003], and their extensive use results in approximately 13,000 underground metal/nonmetal (M/NM) miners (MSHA 2005) in the U.S. being potentially exposed to aerosols and gases emitted by diesel engines (MSHA 2001, MSHA 2006). Exposure to diesel exhaust has been linked to adverse health outcomes including cancer, cardiovascular, and respiratory diseases (Attfield et al. 2012, Silverman et al. 2012), and in 2012 diesel exhaust was categorized by the International Agency for Research on Cancer (IARC) as a Group 1 human carcinogen (IARC 2012). Exposure to diesel particulate matter (DPM) is especially concerning for underground miners since underground mine environments have been shown to have some of the highest levels of diesel exhaust in the U.S. (EPA 2002, MSHA 2001, MSHA 2006, Pronk et al. 2009). Due to the potential for elevated DPM concentrations in mines, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/ nonmetal underground miners to DPM to an eight-hour time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, MSHA 2006, MSHA 2008). Since this rule went into effect, DPM exposures have been reduced, but are still elevated when compared to other occupations (Pronk et al. 2009, Noll et al. 2015). MSHA compliance data between 2005 to the present show that underground blasters represent 21% of all DPM overexposures in M/NM mines and are one of the highest exposed professions in mining often resulting from low ventilation in the area where blasters are working. Because mines have difficulty controlling DPM in these low ventilation areas, additional control technologies may be needed to reduce exposures. Administrative controls, where miners work on off schedules or upstream of diesel vehicles to avoid the exposures to DPM (Noll et al. 2015) is one possibility, but these types of solutions are not always feasible or practical. A canopy air curtain is another potential control technology to help reduce exposures of blasters to DPM. Listak and Beck (2012) showed that this control technology reduced respirable dust concentration under a roof bolter’s canopy by 67%–75% and recommended air velocities greater than 0.5 m/s for dust reductions of greater than 50%. Additional work showed that a canopy air curtain could be designed for a shuttle car, and some initial testing by the National Institute for Occupational Safety and Health (NIOSH) showed reductions of respirable mine dust between 66% to 70%. As seen in Figure 1, the canopy air curtain delivers clean air over the operator’s breathing zone. A fan draws in air through a filter to capture the dust and then supplies clean air beneath the canopy where a miner is working. The use of the canopy air curtain to reduce exposures to diesel particulate matter was first discussed by Noll et al. (2020). In this study the diesel canopy air curtain (DCAC) reduced the DPM concentrations under the canopy by up to 90%. For this research the DCAC was designed to attach to the basket cover of an ammonium nitrate fuel oil ( ANFO) loader (Figure 2) and provide clean air blowing over the miners as they work in the basket. The initial tests used clean air drawn from the mine’s intake and did not try to filter the DPM from the air. Filtering DPM has extra challenges when compared to filtering mine dust particles. The particles of DPM are smaller (submicron and nanometer) than dust particles (greater than 1 micron); therefore, the filtration system must be adjusted to capture submicron particles. A MERV 13 filter was used in previous canopy air curtain research on mine dust control, but this filter is only designed to capture 50%–75% of submicron particles, and this capture efficiency is too low for removing DPM, so a higher efficiency filter is needed. Higher efficiency filters increase the pressure across the filter media which results in decreased airflow or leaks around the filter and reduces the effectiveness of the control for protecting miners from DPM. The optimal filter needs to capture DPM particles at a high efficiency while still allowing the needed airflows to prevent contaminated air from entering the miner’s breathing zone. Listak and Beck (2012) recommended velocities greater than 0.5 m/s for dust reductions of greater than 50%. However, airflows too high have been shown to reduce miners’ thermal comfort; Roghanchi et al. (2016) suggest the optimal velocity for thermal comfort is between 1–2 m/s. Thus, airflow over the miner should be limited to the range of 0.5 to 2.0 m/s. This current study presents the results from research evaluating the reduction of DPM concentrations, under the DCAC, when using a higher efficiency filter (MERV 16) to remove DPM from the DCAC airstream.

Feb 1, 2024