Search Documents

By Ralph H. Light

The recent surge in demand for uranium in the United States, accompanied by a significant increase in price, has resulted in exploration, mining, and milling of lower grade ores than have been exploited in the past. To sustain production levels of uranium with lower grades of feed requires larger tonnage mill operations. Also, because of recent environmental regulations, mill operations must be prepared to properly contain large tonnages of tailings, and recycle, treat and discharge, or evaporate mill effluents. Thus, the advent of lower grade ores, larger tonnage mills, and environmental considerations has made the cost of milling a critical factor in today's uranium production economics in the United States. Three basic milling methods are employed for extracting uranium from ores: 1. Acid leach, countercurrent decantation, and solvent extraction. 2. Acid leach, resin-in-pulp, and Eluex. 3. Alkaline leach, solid-liquor separation, and precipitation. Vanadium often occurs as a valuable by-product in ore deposits located in the Uravan mineral belt in Western Colorado. Also, lesser amounts of vanadium may occur in ores from South Dakota, New Mexico, and Utah. Vanadium is usually extracted in the acid leach solution with uranium and recovered by solvent extraction after recovery of the uranium. By-product recovery of uranium from phosphoric acid and porphyry copper dump leach solutions is now receiving considerable attention. Pilot plant studies are under way and construction of commercial plants is in progress.

Jan 1, 1977

By E. C. Winegartner

In producing and selling coal, the coal company is faced with many different parameters by which the quality of its product is evaluated. One type, which we choose to call the economic parameters, includes moisture, ash, sulfur, and Btu's. These are reasonably well understood by both the coal supplier and the customer, and the dollar values can be placed on them. This is the group of parameters of primary interest to most purchasing agents buying coal. A second group of parameters governs how the coal will behave in the boiler itself and is of primary concern to the engineers designing the boiler and to the men who must operate and maintain it. Since we have not yet learned to put dollar values on these parameters, they generally show up in coal contracts simply as cutoff points, the purchaser simply saying that he will not accept coal outside of certain limits.

Jan 1, 1975

By Henry E. Swanson

In the early 1960's the Company, then named the United States Smelting Refining and Mining Company, was drilling the Continental ore body located near Fierro, New Mexico. Reserves of underground ore of sufficient quantity were indicated to build a mill. At the same time some ore from the Continental No. 1 mine was being milled at the Company's Bullfrog Mill, formerly a lead-zinc mill. The copper ore in comparison to the lead-zinc ores was very hard, abrasive, and heavy. These factors pointed out the possibility and attractiveness of autogenous grinding. While prior to this some study had been given to autogenous grinding, no large scale tests had been made. Such a program was carried out and from the pilot plant data the following was established: 1. Grinding of the ore by autogenous means could be accomplished. 2. This could be done in one stage; however, not at a satisfactory tonnage throughput rate. Thus, the use of a secondary unit has been employed. 3. Grinding in the secondary unit could be done by pebbles generated in the primary unit. This resulted in the scheme whereby the ore would be ground 100% autogenously. 4. Liberation of the copper minerals was excellent so that good recovery at a satisfactory concentrate grade would be obtainable.

Jan 1, 1976

By D. Zim

Mining activity in South America is a growing enterprise. One of difficulties found in many areas of the South American continent, especially in north Chile and south Peru, is the shortage of water supply. In order to overcome this difficulty some mining companies proposed to transport the water from Pacific Ocean up to the mountains. This can be accomplished by the use of stainless steel pipelines, but this is a cost prohibitive solution and is also subject to severe pitting corrosion in a saline environment. The use of mild steel may be a lower cost solution than stainless steel as the material of construction for pipelines but it is subject to corrosion anyway. The corrosion in this case can be internal or external corrosion although cathodic protection as well preventive maintenance usually is enough to mitigate external corrosion without the need to shut down the pipeline. The same is not true about the prevention of internal corrosion. It is not practical, sometimes not even possible, shutdown a pipeline to carry out an inspection and fix sections where potential failures are detected. It is possible avoid corrosion caused by sea water within the mild steel pipelines by applying a proper chemical program designed to virtually eliminate dissolved oxygen in the water commonly called deaeration.1 This type of treatment obviously involves additional capital investment since it requires the construction of one deaerator with the first pumping station and additional equipment at each point where the water can come into contact with oxygen. Deaerators will increase operational costs and subsequent injection of chemicals will be required in the case of multiple degasification facilities thus increasing the consumption of chemicals. grams based on oxygen scavengers, the objective of the present study is to develop a new water treatment capable of preventing mild steel corrosion in aerated sea water. The new treatment must be able to prevent both generalized and localized (pitting) corrosion and overcome the necessity to construct and operate deaerators.

Feb 23, 2014

For the past two years, Cliffs Natural Resources in Minnesota has tried an experiment: it has staffed a booth at the Iron Range Earth Fest. ?It was a little unusual for a mining company to participate in an event that centers around preserving the Earth?s resources,? said Julie Lucas, environmental manager at Hibbing Taconite Company. ?But Cliffs is a sustainable company and we want to take every opportunity to share information about our practices. We found the response to be overwhelmingly positive.? Cliffs? outreach effort is just one of the surprising ways mining companies across Minnesota are reaching out to stakeholders and finding success. The 85th annual SME Minnesota Section Meeting (73rd Annual University of Minnesota Mining Symposium), held April 17-18 in Duluth, MN, demonstrated the Minnesota mining community?s commitment to connection and collaboration, and how that approach is bringing success.

Jan 1, 2012

By K. T. Stafford, N. A. Iverson, V. T. McLemore

Southwestern New Mexico is part of a large belt of Late Cretaceous to Eocene copper porphyry deposits found in Arizona, New Mexico, and Mexico. These deposits are the result of arc magmatism that occurred during the Laramide orogeny. Recently, attention has been brought to other commodities that can be extracted as by- and co-products, many of which are critical minerals. A new compilation of the geochronology of these deposits shows two main pulses of magmatism that produced mineralized deposits and, along with new dates by the author, shines new light on the geologic history of these deposits and the role it plays in critical mineral abundance.

Feb 1, 2024

By Enrique Llewellyn

North River Energy Company a previous subsidiary of Republic Steel Corporation commenced development of the Number One Mine in mid-1972. The mine is located in West Alabama and presently employs a total of 632 people. Production capabilities have increased to 1.4 million clean tons of steam coal per year with the newly purchased Longwall System. Washer recovery averages 57 percent. The seam being mined is the Pratt or Corona with an average height of 52 inches and an average cover of 540 feet. The immediate roof is laminated sandstone and the floor is composed of a hard fireclay. Total production out of the mine is provided to Alabama Power Company under a longtime contract.

Jan 1, 1981

By Douglas B. Silver

Study Parameters (Status as of February 1993) Time Period: 1989 -1991 151 North American Public Metal Mining Companies Fiscal not calendar year basis 85+% of Canadian and U.S. Metal Production Au, Ag, Cu, Pb, Zn, Mo, Ni, W Results are Preliminary and Research Continues Chicken Little is Alive and Well

Jan 1, 1993

By Peter Johnson, David Barber, Lachlan Henderson

"The traditional approach to rail tunnel fire safety design is to follow NFPA 130, which assumes a major tunnel fire could occur and requires bi-directional emergency ventilation. There is no regard to the impact of ventilation on fire growth and smoke production. In Europe and other parts of the world, the need for tunnel ventilation systems to provide smoke management in the event of fire is being questioned. The European Commission’s Safety in Railway Tunnels TSI is based on a philosophy that improved running capability (preventing fires and other events stopping the train in the tunnel) and elevated fire performance of materials means the chances of a major fire in a tunnel is highly unlikely, with only small fires expected, and no tunnel ventilation required. This approach is reinforced by the International Tunneling Association which has recently published an Engineering Methodology for Performance Based Fire Safety Design on Underground Rail Systems, which includes a methodology that does not require assessment of tenability in tunnels, but requires a scenario based risk assessment to be undertaken to determine overall fire safety measures. Recent research by the University of Edinburgh has shown that forced airflow from a mechanical ventilation system may promote fire growth and increase smoke volumes much more than with natural ventilation. Whilst the concept of no mechanical ventilation (i.e. natural ventilation) is a new concept for some, for many rail tunnels it is worthy of serious further consideration. RAIL TUNNEL SMOKE MANAGEMENT AND STANDARDS Smoke management using mechanical bi-directional ventilation systems has been a central part of the fire safety design solution under NFPA 130 for rail tunnels since 1982. The current version of the standard, NFPA 130: 2014, states that mechanical ventilation should be fitted to rail tunnels of length greater than 305 meters and an engineering analysis should be undertaken for tunnels of length 61 to 305 meters to determine whether mechanical ventilation should be fitted. However, this approach is not necessarily reflected elsewhere in the world. In Europe in particular, mechanical ventilation systems for smoke control within rail tunnels have taken a much less central role within the standards framework."

Jan 1, 2016

By Julian Glasser

Starting with rutile, containing more than 55% TiO2 and of the proper particle size, the commercial production of titanium tetrachloride via fluidized bed chlorination is relatively very simple and economical. As compared to shaft chlorination, it operates at a much higher capacity for given sizing of equipment, and appears more foolproof, requiring less attention. Operating data were obtained on a 53" diameter fluidized bed chlorinator using Australian rutile and petroleum coke of controlled particle size. Production rates varied from 20 to 50 tons of crude TIC14 per day for a campaign extending over one month. Close to theoretical yields and efficiencies were obtained from the viewpoint of chlorine and/or rutile consumption. Details of important equipment design, critical operating conditions and pertinent results are described.

Jan 1, 1962

By Russell E. Martin

Excavating and lining twin interstate highway tunnels each 11.3 m (37 ft) high by 14.6 m (48 ft) wide by 183 m (600 ft) long. A discussion of the geology of the site and problems occurring at the portals and the solutions to the problems. The methods used in placing the concrete lining are also discussed.

Jan 1, 1987

By V. A. Kharchenko, V. M. Yeremeev

INITIAL PRECONDITIONS To solve tile problem of using the potential reserves of the different coal ranks efficiently (the coal reserves being many times superior in quantity to those of natural gas and oil) one must realise an integrated estimation of the coalfields' and coal deposits' reserves. The actuality of this problem increased especially in the recent years, when the Russian coal industry is being restructured. A structural reorgaisation of this industry, in order to in- crease its efficiency, covers a large spectrum of social and economic problems, comprising a withdrawal from mining the coal reserves that are unsafe from the standpoint of economy and labour protection. According to the information supplied by the 'Rossoogol' company, the Russian coal industry, accounting for abut a fifth of the world coal reserves, has a rather unsafe resource base, for about 5% of the reserves involved in mining do not correspond to the world practice conditions, regarding the coal grade, thickness, geological conditions, proneness to coal and gas outburst hazards. These concern first of all the Moscow, Kizelovsk and Donetsk coal basins, the Prokopievsk-Kiselevsk district of the Kuzbas basin and several other coalfields. Thus, the problem of efficient potential coal reserves' utilization calls for a paramount solution of two basic problems, namely: a) a comparative coalfields' and sections evaluation, and their ranging, in accordance with their industrial importance; b) choosing the 'active' reserves good to be efficiently mined under the present-day conditions. PRINCIPLES OF EVALUATION The investigations that had been carried out make it possible to formulate the following basic principles of the coalfields' reserves' estimation (or assessment). 1. The necessity, possibility and expediency of coal reserves' industrial exploitation are determined by a set of natural, technical, technological, practical, economic, environmental and social factors, thus calling for an integrated and gradual approach to problem solving. 2. One cannot consider the results of same reserves' estimation as being invariable because the former depend both upon constant (mainly natural) and market demands for different grades of coal (those of different power engineering and technological situations), capital investments, material and labour resources, economic (price-forming), technical, technological, environmental and other factors. 3. The rational size and sequence of the operating mines' and reserve sections' resources' involvement into mining depend upon the final aim of posing the problem, whose variants may be (the corresponding limitations being considered) providing for a maximum run-of-mine output (these essentially featuring the past stages of the industry's evolution); providing for a maximum efficiency, measured possibly by the specific or absolute indices of profits an expenses, labour productivity e. al. ; providing for a maximum extraction (maximum integrate utilization) of the known reserves. In this case an important park goes to the economic evaluation (or assessment) of useful application of the by-products being extracted (methane, mine water, rack) compared to the expenses necessary for their utilization. Regarding the steam coal (posing the problem any way it be possible), and extreme limit to the absolute non-efficiency of the coal reserves' exploitation may be posed, using the proportion of energy obtained from the possible amount of the coal to be extracted to the energy consumption necessary to extract, prepare, haul and consume this amount of coal. 4. The most reliable and efficient solutions providing for opening the reserves can be obtained for group of mines, rather than at the level of an individual mine section or an individual mine because it is only in the former case that the possibilities to re- distribute the expenses necessary to develop the good for mining and worse sections and seams can be realized to the greatest extent. Therefore the prospective approach to be considered is the one providing for an integrated organization and choice of the optimum combination of the variants of the ways to use the mines in operation and the free sections of the region in order to satisfy the growing up requirements for coal rather than the one providing for individual mine sections' resources' evaluation. 5. The future possibility and expediency of coal reserves' industrial exploitation will depend upon the prospects to implant at the mines in operation and reserve sections new engineering and technological elements and coal extraction technologies which may essentially change the actual idea concerning the coal reserves worth of being developed in an efficient way. For example, reserves not available to be exploited using conventional coal extraction technology may be regarded as potential resources for in situ gasification, e. g. the operating mines' reserves (non-commercial and non-mined commercial ones), balance and outside balance reserves of the free sections having proved not available to be mined using conventional coal-extraction technologies, as well as the non-extracted reserves of the abandoned and closed mines.

Jan 1, 1996

By M. A. Reyes, J. Bickson, J. R. Srednicki

Federal laws mandate the presence of refuge alternatives (RAs) in underground coal mines and provide guidelines for harmful gas removal. After an explosion, harmful gases can follow survivors into an RA and can reach a deadly concentration. Investigators from the National Institute for Occupational Safety and Health (NIOSH) tested 12 ventilation system configurations (VSCs) to purge sulfur hexafluoride (SF6) tracer gas from a built-in-place (BIP) RA in the Experimental Mine in Bruceton, PA. Using a borehole air supply, tests were conducted with airflows of 750 and 1,000 standard cubic feet per minute (SCFM). Excluding a VSC where the air inlet was 1.98 m (78 in) from the air outlet, the results show that the time to purge the SF6 concentration from 1,000 parts per million (ppm) to 25 ppm ranged from 26 to 29 minutes for an airflow of 750 SCFM and ranged from 18 to 23 minutes for an airflow 1,000 SCFM. Mines can use this information to reduce purge time in case of a mine disaster and determine which VSC to avoid. INTRODUCTION After a fire or an explosion in an underground mine, the concentration of carbon monoxide can reach a fatal level. In a mine disaster, the main goal is to escape. However, if miners cannot escape, they have to migrate to a location to find refuge and, if possible, communication, and a borehole source for a fresh air supply. To ensure survival of the miners, Federal laws mandate the presence of a refuge alternative (RA) within 304.5 m (1,000 ft) of the nearest mining face. In addition, Code of Federal Regulations Title 30 CFR Section 7 sets the guidelines for personnel tracking, RAs, and the removal of noxious gases in underground coal mines (Mineral Resources, 30 CFR, 2014). Federal regulations define an RA as a protected, secure space with an isolated atmosphere and integrated components (Mineral Resources, 30 CFR, 2014). There are three types of RAs: portable metal RAs, portable tent-type RAs, and built-in-place (BIP) RAs. A BIP RA is constructed using masonry or other stoppings to create an isolated space in a mined-out area. Blast doors are installed in one or both of the stoppings for the miners to enter the RA. Furthermore, RAs must provide the following components: breathable air, food, water, air monitoring, and harmful gas removal. Federal regulations have emphasized the mandate for breathable air and harmful gas removal in the following words: “Purging or other effective procedures shall be provided for the airlock to dilute the carbon monoxide concentration to 25 ppm” (Mineral Resources, 30 CFR, 2014). The purpose of the mine ventilation system is to provide a sufficient quantity of air to the underground mine workings, to dilute methane and other contaminants, to maintain a suitable working environment, and to prevent accidents from happening (Cheng and Wei, 2014). In addition, the organic nature of coal amplifies risks from poisonous gases, explosions, and fires (Engström et al., 2018). If an underground coal mine ventilation system fails after an explosion, the concentration of toxic gases, most notably carbon monoxide, will increase. Carbon monoxide is dangerous because it creates tissue hypoxia by binding to hemoglobin (Özmen and Aksoy, 2015).

Jan 1, 2019

By Deepak Malhotra

This paper discusses the need for periodic auditing of mineral processing flowsheets and the potential benefits a company can gain from a study of this nature. A carefully designed flowsheet auditing can have a significant impact on the metallurgical performance in the plant. Several case studies illustrating the potential benefits that can be attained from flowsheet auditing of mineral processing plants are discussed.

Jan 1, 1986

By F. M. Doyle, J. P. Dwyer

Introduction The mining industry has a poor public image. It is often perceived as a despoiler of the landscape and a polluter of the environment, and there is little recognition of societal needs for the raw materials and fuels that this industry produces. There are many reasons for this poor image, but an important one is that a substantial number of mining operations have caused significant damage to the environment. Many of these operations, particularly those that now are abandoned, continue to have an adverse impact, principally in the form of water pollution.1 In some cases, the damage caused by this pollution extends well beyond the immediate region around the mine. Chemical contamination of ground and surface waters can, and does, occur in nature when these waters flow through or over undisturbed, mineralized rock masses. However, the problem is greatly exacerbated by mining because the mining activities increase, by several orders of magnitude, the permeability and the surface area of rock that can be contacted by percolating water. Water flowing through either the mine workings or the waste rock dumps becomes contaminated. Pollution can also arise if leachate from tailings ponds enters either groundwater or surface waters. This leachate may contain chemicals used in processing the ore. The magnitude of the threat posed by mining wastes depends on the type of minerals in the deposit, and on the chemicals used to process the ore. The magnitude of the threat also depends on two other, site-specific factors. One is the volume of water flowing into the mine and through the dumps, which depends on rainfall patterns, topography, and whether the mine workings are surface or underground. The other is the proximity of the pollution source to groundwater or surface waters, which depends on both the climate and geology. These factors influence the concentration and the quantity of polluted water forming and reaching the receiving water. Mining activities present a potential problem of enormous scale. Vast amounts of rock are mined each year2 and, as noted above, substantial problems have arisen at some mine sites. These problems are usually exceedingly costly to address, and it is imperative that these mistakes not be repeated. There are indications that we can accomplish this goal; we now better understand the processes that cause pollution and have methods to prevent or contain it. In addition, in the past few decades society has started to recognize the need for all industries to operate in a manner that maximizes the health and safety of workers and the public and minimizes adverse environmental impacts. A variety of recently enacted federal and state laws regulating public health and environmental hazards reflect the increasing concern over these issues. Many statutes, such as the federal Clean Air Act and the Clean Water Act, encompass activities undertaken by the mining industry. Other laws, such as the Surface Mining Control and Reclamation Act, have been written to regulate specific hazards posed by this industry. At the present time, the federal government. through the Environmental Protection Agency (EPA), and several state governments, are preparing new regulations specifically tailored to control the disposal of mining wastes. Given the magnitude of the potential environmental and health risks posed by disposal of mining wastes and the regulatory costs to the mining industry (both of which are due to the tremendous volume of waste generated), it is especially important that regulators have a good understanding of the different types of mining wastes and the risks they are likely to pose in various geographic and climatic circumstances. Only then can a regulatory program be designed with suitable procedures and substantive criteria to protect the environment and ensure compliance, while avoiding unnecessary or wasteful expenditures. California has long enjoyed a large, active mining industry. Today it produces a wide range of mineral commodities. The revenue from production of non-fuel minerals in California ($2.85 billion in 1988) greatly exceeds that of any other state. About a third of this revenue is from the production of inert sand, gravel and crushed stone. However, the remainder is from the production of a wide range of materials. These include boron minerals, rare earths, asbestos, talc and pyrophyllite, and gold. In earlier decades, an even broader range of minerals was produced, including mercury, copper, lead, zinc, and barite. There are acute environmental problems at some of these early mine sites. Because in 1987 the state of California was engaged in a revision of its regulations for mining waste disposal, the legislature commissioned a study by researchers at the University of California at Berkeley to investigate and review: the magnitude of the problem posed by these wastes, • the best feasible control measures available for waste management and disposal, • the problems of abatement and cleanup at so-called "problem" mine sites, • the current regulations imposed on mining waste disposal by various federal, state, and local agencies and the effectiveness of these regulations. This paper summarizes the principal findings from this study (Mining Waste Study, 1988). The lessons from this investigation are likely to be of general interest because of the diversity of mineral products produced, and the wide range of geographic and climatic conditions encountered. The acute problems seen at some of the older mines are typical of the western United States, and teach useful lessons on strategies that should be implemented at new mines to prevent recurrences of these problems.

Jan 1, 1992

By David N. Hedges

This paper discusses the actual recovery and installation of a longwall in a bituminous coal mine in Western Pennsylvania. The coal bed mined is in the Lower Freeport seam which averages 42 inches (1.07m) in height locally. Drainage from the mine is approximately 3.5 million gallons of water per day (13.25 million liters per day). This water deteriorates the mines predominately fire clay bottom making it extremely difficult to move equipment. Support removal is accomplished by pulling the 6 ton (5443 kg) shields out under their own hydraulic power and transporting them by track over four miles (6437m) co the next longwall panel. This paper also discusses the changes that will be made to aid in the succeeding longwall recoveries and installations.

Jan 1, 1984

By Sahin Furkan Sahiner, Onur Golbasi

Effective maintenance planning is vital for coal mining operations, where haul truck fleets directly determine production continuity. This study presents a discrete event simulation (DES) model for evaluating maintenance strategies under multiple failure modes and their interdependencies. The model integrates corrective, periodic preventive, and opportunistic maintenance, dynamically updating equipment lifetimes through probabilistic time-betweenfailure and time-to-repair distributions. Applied to a fivetruck coal haulage fleet over a one-year horizon, results show that periodic preventive maintenance delivers the highest availability (76%) under unconstrained conditions, slightly outperforming corrective-only maintenance (75%). Opportunistic and integrated approaches performed worse (68% and 69%), reflecting redundancy from overlapping interventions. These findings suggest that structured preventive programs provide the most reliable outcomes when costs and resources are not limiting. The DES framework serves as a baseline for future models incorporating cost, spare parts logistics, and workforce availability, supporting robust maintenance planning in coal mining operations.

Feb 22, 2026

By L. Yan, C. Zhou, M. Reyes

"The MINER Act requires the installation of post-accident, two-way communications and electronic tracking systems for all coal mines. One communication system which can satisfy this requirement is an electrode-based, through-the-earth (TTE) communication system, which sends signal directly through the overburden of a mine. The performance of these types of systems relies on several controlling factors such as earth conductivity, overburden depth, operating frequency, TX/RX antenna length, TX/RX offset, TX/RX orientation angle and TX current. In an effort to estimate attenuation through the earth, NIOSH researchers developed an analytic solution for the electrical field distribution of an electrode-based TTE communication system for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source. The analytic model was then validated using test data measured at an operating coal mine. The validated model can be used to optimize the operating frequency, estimate the required transmitting current, choose appropriate TX/RX orientation, and predict the performance of an electrode-based TTE system at a coal mine. INTRODUCTION One of the requirements of the Mine Improvement and New Emergency Response Act (MINER Act) of 2006 is the installation of post-accident, two-way communications and electronic tracking systems for all underground coal mines. As one of the through-the-earth (TTE) wireless communication methods available for the mining industry, the electrode-based, or linear, TTE systems establish communication by inducing a current within the earth medium by use of a pair of current probes. The resultant current is detected as a voltage by a similar set of distant probes. These probes could be an insulated piece of wire tied to two electrodes grounded at distant ends, or the grounded ends could be rails, roof bolts, or grounded electric rods. The analytical solution developed in a homogenous half-space, for this form for various transmitter/receiver (TX/RX) configurations, will be presented in this paper. The communication signals can be sent either from underground to surface (uplink) or from surface to underground (downlink). In order to achieve a successful communication link, it is necessary to understand the electric fields within the earth so that the appropriate size of transmitting antenna, TX/RX relative orientation, and operating frequency can be chosen. Hill and Wait gave the explicit forms of partial magnetic fields and partial electric fields of electrode-based TTE downlink communication with finite cable length [1]. In prior research, the E-fields of electric line transmitter were obtained for a static TX current [2] [3]. In this paper, the general and explicit forms for electrode-based TTE electric fields are developed and presented. The solutions for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source obtained from these forms are presented. Also, factors that affect the E-field strength at RX are discussed."

Jan 1, 2017

By Gilbert C. Robinson

Manufacturers of brick and tile are showing growing interest in the possibility of manufacture of a clay bonded block. The block would have the shape of concrete block, but would be made without the use of Portland cement, Instead, the block would be made&apos; from mixtures&apos; of an aggregate and the present raw materials of the brick industry. The finished units would weigh 20 to 30 pounds and meet the specifications for Grade A concrete block. The present status of the clay block development shows one manufacturer actually in production of these units$, two additional manufacturers are attempting production and many manufacturers are actively engaged in development work. At least four major research laboratories are engaged in the development program. There are several different processes available for clay block production. These processes differ primarily in the type of aggregate used or in the type of forming operation selected. I would like summarize these possible methods.

Jan 1, 1960

By Rusdian F. Kayadoe, Michael B. Hutahaean, Sandi A. Firmanulhaq

Deep Mill Level Zone (DMLZ) mine is located in Papua, Indonesia operated by PT Freeport Indonesia (PTFI) with approximately 1,500m below surface. The ore body extend 1230m width from northwest to southeast by 300–400m length east-west. The mine currently produces at full production of 80,000 tons per day until 2041. Part of the extension of current active production block and mitigation sits 225 m above the production block 1 (PB1) and 2 (PB2A and PB2B) which located in 2590L, named production block#4 (PB4W and PB4E). As the mining continues at PB1N, PB2A, and PB2B, the cave growth vertically and laterally to south perimeter of the footprint affecting the integrity of PB4W/E footprint. Currently, PB1N and PB2N are in active production whilst PB4E development continues from South against PB1N cave, as can be seen in Figure 1. A slight overlapping between PB1E and PB4E intentionally to promote cave connections between the two caves. Despite low stress model in the PB4E near existing caves, the PB4E cave propagation expected by the large strain and will be propagating in tension failure to the PB1E cave. Hence, designing the drill drives edge and first drawbell location as close as possible to the PB1E cave is necessary to guarantee cave connection. Since PB4 footprint development commenced in December 2021, there have been a substantial cave propagation observed from existing downhole monitoring. As the PB4 footprint designed perpendicular to existing DMLZ PB1 cave, adjustment of the development edge design is necessary to reflect the progression the loosening zone propagation to the South. Final life of mine design for extraction, undercut and ventilation level were decided in October 2023 considering latest update cave (fractured/ yielded) boundary. Numerical model of potential rock mass damage also aids the decision to locate the drift edge design. Predicting the cave progression impact is critical to both production at the existing active blocks and development of the new area. The use of cave shape data from year 2021–2023 gives an insight of the cave shape estimation at the end of 2024 when the undercut drift will be developed. This paper presents actual cave growth of active production blocks and its relative vertical progression impact as the result of drawing in order to plan for acceptable rate and provide mitigation once the minimum acceptable rock mass condition and minimum pillar threshold achieved.

Feb 1, 2025