Search Documents

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rockmass strength. Past studies have largely used arbitrary scaling approaches to produce rockmass strength from laboratory rock tests. This paper proposes a stochastic approach to produce rockmass strength from laboratory rock tests. Based on the laboratory data, MATLAB with an extreme value stochastic model generated a database for each physico-mechanical property of the rock. Then finite-difference software FLAC2D simulated laboratory-sized rock specimens. Random material properties in MATLAB were generated using the grids developed in the numerical model. The random properties were then applied to the final FLAC2D model. Model runs simulated the approach performed in the laboratory. The results from the model indicate that a stochastic approach produced compressive strengths that were lower than those from the deterministic approach. Failure modes for each specimen were different from those observed in the laboratory. In addition, random density also influenced the failure mode, highlighting the importance of stochastic analysis in rocks.

By T. J. Lutz, D. S. Yantek, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

Federal regulations require the installation of refuge alternatives in underground coal mines. Of the inuse refuge alternatives, more than 95 percent are mobile refuge alternatives, with the remainder being built-in-place (BIP) refuge alternatives. Heat/humidity buildup has been one of the major concerns with mobile refuge alternatives. For BIP refuge alternatives, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP refuge alternatives, the U.S. National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP refuge alternative with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP refuge alternative. The results show that the air supplied to a BIP refuge alternative may require heating or cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 21 °C (70 °F) and a relative humidity of 90 percent, providing 13 °C (55 °F) dew point air at 775 scfm, which is slightly higher than the mandated flow rate of 12.5 scfm per person, kept the internal apparent temperature below the mandated 35 °C (95 °F). Results for each test case are presented.

Jan 1, 2018

By Robert C. Bates

Published information discussing uranium mine radon daughter controls and related costs was examined and used to develop an estimated (projected) cost per ton for any level of control. Results show a clear power function increase of cost for conventional dilution ventilation as the annual exposure limit is lowered. Projections can be made using any assumed changes in consumer price index (CPI) and radon daughter working level months exposure limit. Bounds on the estimated costs are provided, and applicability of the final equation is discussed.

Jan 1, 1983

By Rebecca Boakye, Zohreh Kazemi Motlagh, Virginia T. McLemore

The most significant uranium (U) deposits in New Mexico are sandstone-hosted deposits in the Morrison Formation (Westwater Canyon Member), where >169,500 short tons of U3O8 were produced from 1950 to 2002. In addition, >9076 pounds of vanadium (V, a critical mineral) and some molybdenum (Mo) were produced from these deposits. These and other U deposits (limestone-hosted, U-veins) in New Mexico also contain critical minerals. Critical minerals are mineral resources that are essential to our economy and whose supply may be disrupted; many critical minerals are 100% imported into the U.S. Some sandstonehosted, limestone-hosted, and U-vein deposits are elevated in heavy rare earth elements. One sandstone-hosted sample contained 0.3 ppm Re (critical mineral), 659 ppm Se and 408 ppm Mo. The arsenide five-element vein deposits in the Black Hawk district are mineralogically and texturally complex, low- to moderate-temperature, hydrothermal, structurally-controlled, Ag-Co-Ni-Bi-As bearing carbonate vein systems with local minor elements. Mineralized samples from Black Hawk contain up to 9970 ppm Ag, 8540 ppm As, 5690 ppm Co, 72,400 ppm Ni, 57 ppm Bi, 165 ppm Sb, and 32,600 ppm U.

Feb 22, 2026

By K. T. Stafford, N. A. Iverson, V. T. McLemore

Laramide porphyry copper deposits are large, low grade (<0.8% Cu) deposits that contain disseminated copper minerals, breccias, and stockwork veinlets of copper and molybdenum sulfides associated with porphyritic intrusions in Southwestern New Mexico. Critical minerals, such as PGEs, tellurium, indium, germanium, and gallium are recovered from the anode slimes remaining after copper is refined. Detailed age dating, mineralogy, geochemistry, along with geologic mapping could refine the location of critical minerals within specific systems and could identify porphyry systems with elevated critical minerals that could become economic, in addition to the already produced copper, gold and molybdenum.

Feb 1, 2023

By D. PATIL, B. K. Parekh

Water is the mainstay for the beneficiation of fine-size coal and minerals, but it is also the least desirable constituent of the final product. The basic concept of the novel process described in this paper is based on the differential surface heat absorption capacity of the individual particles. When a differentially heated solid mixture is placed on a moving belt that has been coated with low-temperature melting resin, the hotter component of the mixture will stick to the belt while the relatively cooler component will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal and quartz particles of 6 × 18 mesh size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating and system variables. Preliminary test results show that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

By Michael Wortley

Metso?s Process Technology and Innovation group is a world leader in mineral processing consulting. A significant amount of this consulting work involves process integration and optimization (PIO) studies, which include investigating the effects of drill-and-blast design and implementation on downstream processing. Critical to these studies is the ability to track specific ore into, and through, the plant. To increase the accuracy of this ore tracking, Metso Process Technology and Innovation (PTI) developed a system to track ore using a radio frequency identification (RFID) transponders technology designed to allow tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles and, finally, into the concentrator. The system is called SmartTag. Since its commercialization in 2007, SmartTag has been used in the majority of PTI?s consulting projects, and several permanent systems have been installed worldwide.

Jan 1, 2012

By Arif Emre Dursun

The aim of this study is to present hazard classifications of location, type and causes of accidents in the Turkish coal-extracting industry using the analytic hierarchy process (AHP). In this study, fatal mine accidents were analyzed by pairwise comparison and weighting, and the most important hazards were identified by determining the effective main and sub-criteria among location, type and causes of accidents. For this purpose, first-, second- and third-level hazards consisting of location, type and causes of accident were determined by using the data of fatal mine accidents in underground and openpit coal mining in Turkey between 2010 and 2020.

May 1, 2024

By S. J. Schatzel, V. Gangrade

A ventilation research study was conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) and a cooperating longwall trona mine in the Green River basin of Wyoming in the United States. The objective of the study was to evaluate the movement of longwall face air and exchanges between the face and worked-out areas to document the presence or absence of face airflow pathways between these locations. Tracer gas experiments using sulfur hexafluoride (SF6  ) were conducted to describe air movement on the face and in the mined portion of the active panel. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of gases emitted from the face and caved gob.

By B. C. Williams

The Bureau of Mines monitored the water quality in and near a copper/gold tailings impoundment. Samples were taken from the unsaturated %one. and dissolved concentrations of over ZO constituents were measured with respect to depth and moisture content, factors which influence oxygen content and sulfide oxidation. Samples from the unsaturated %one were drawn through a hypodermic needle sampler into individually evacuated vials fitted with septa, thus preventing oxygen contamination. Water quality was also monitored in the saturated tailings, underlying colluvial aquifer, and weathered andesite bedrock.

Jan 1, 1989

By John E. Appleby

Grupo Acera, HYLSA originated in 1942 when Hojalata y Lamina began operations to supply steel strip for the Cuauhtémoc Brewery, the parent company. Production began in April, 1943 with growth accelerated because of World War II. By 1948 the company was producing its own steel from electric furnaces charged with scrap iron. Further expansion was hampered by the fluctuations in availability, price and quality of scrap iron. As a result, a search was made for a suitable process to enable HYLSA to satisfy its need for a reliable source of feed for its steel-making facilities. Their relatively low iron requirements at the time did not justify the very high capital investments required using the conventional blast furnace method. Processes which by-passed the blast furnaces were very much in their infancy and were not commercially tested. HYLSA then undertook an investigation of the direct reduction processes, knowing full well that much larger companies in other countries had investigated several processes but their work had not established a trend toward direct reduction or any particular process. However, after much effort and persistence HYLSA arrived at a process which suited their conditions. By using Mexican iron ore and natural gas they developed the now well-known H. y L. Process to produce sponge iron. Concurrent with the start of investigations which led to the H. y L. Process, HYLSA began an exploration program for a suitable source of iron ore. Thus in 1951, Cia. Minera Las Encinas, S.A. was formed, culminating in the development of the ore bodies near Pihuamo in the State of Jalisco. Mining commenced and ore was

Jan 1, 1971

By YUSONG MIAO, DI WU, XIANRONG YAN, YIPING ZHANG, JIE LIN, KEBIN LI

Rock fragmentation has been a concern in hard-rock mining for the mining industry. Rock fragmentation distribution is an important index to measure the blasting effect. It not only affects the cost of drilling and blasting, but also affects the efficiency of subsequent operations, such as loading, transportation and secondary crushing.

By GRANT COLLIGAN, BROCK O’KELLEY, Corby Anderson

With the world’s ever-growing push to expand technological capabilities, the need for specialized materials including rare earth elements has exploded. One source of rare earths found in the United States is bastnaesite, a rare-earth-bearing fluorocarbonate, mined at the Mountain Pass Mine in California. To increase production, it has been essential to optimize existing processes and create new ones to capture current reserves. This paper presents the results of a research program conducted to expand the understanding of the bastnaesite leaching system. With the help of prior knowledge and thermodynamic calculations, a novel single-stage hydrochloric acid leach system was created to optimize the extraction of rare earths from bastnaesite. Historically, this extraction has entailed the use of a two-stage leach system involving a high-temperature hydrochloric acid leach followed by a caustic crack. We ran a series of single-stage leach experiments by reacting locked-cycle flotation concentrate with hydrochloric acid to test common leaching parameters. The results of these single-stage tests showed significantly higher rare-earth recoveries than the reported recoveries of the historic two-stage caustic crack processes, all while decreasing the number and amount of reagents needed.

Feb 1, 2023

By M. Ge

An in-seam seismic (ISS) - based void detection technique was developed and tested for three general mine conditions: anthracite, bituminous and trona. The detection range tested varied from 80 to 100 m for trona mines and from 33 to 66 m for bituminous mines. High quality and broad band signals were obtained from these tests and were used to delineate the voids. The paper provides a brief discussion on the technical features of this void detection technique, the testing conditions and results, and a general assessment of the technique.

Jan 1, 2010

By W. C. Yates

Lack of visibility from large, open-pit haulage truck cabs has become a serious safety problem. Anaconda conducted a research program to develop a low cost system to alert haulage truck operators to small vehicles present in blind areas. Several systems were developed and tested. As open-pit haulage truck size has increased, so has the size of the blind areas. Mine utility vehicles, pickup trucks, and cars are concealed within these blind areas and become safety hazards. Figure 1 shows the typical blind areas of a 136 t (150-ton) haulage truck. The areas of greatest concern are at the rear center and front right corner of the truck. In these "no visibility" areas many small vehicles have been crushed by large haulage trucks at various mine sites. In most instances, the occupants escaped the vehicle before it was destroyed. But injuries and death have occurred. In most cases, the accidents were attributed to negligence or carelessness by the small vehicle driver. The limited visibility problem still exists, though, and a solution is needed. Initial Solution The usual plane mirror on the driver&apos;s side and the convex mirror on the right front of the haulage truck allow only limited rear visibility. The typical, right side convex mirror is generally small and difficult to locate at a glance. This convex mirror also presents an image that distorts distance perception. These mirrors are of¬ten broken and immediate replacement not demanded or made. The US Bureau of Mines, in a contract with M.B. Associates, San Ramon, CA, developed an improved visibility system. It consisted of a larger, left view mirror and unique, blind area viewer. The large 230 x 690 mm (9 x 27 in.) left mirror has a small convex spot mirror near the bottom. The entire unit can be quickly replaced if broken. The large size provides a full view of driver orientation features such as the rear tire and the top of the load bed. The right 300 x 410 mm (12 x 16 in.) mirror has a convex surface and is quite rugged. The 510 mm (20 in.) spherical radius presents the operator with some distance distortion, but objects in its view are easily seen. The "blind area viewer" consists of a modified fresnel lens that allows the driver to "look around the corner." Installation of three of these lenses on the front of each haulage truck is rec¬ommended for adequate blind area coverage. This system significantly increases an operator&apos;s field of view and allows viewing of objects within about 3 m (9.8 ft of the truck. Many open-pit mines are nor mounting on smaller vehicles a long whip with a flag and lamp or both. This increases vehicle visibility to haulage truck operators. The whip is permanently attached to the mine vehicle. It can also be magnetically attached to transient vehicles. The whip system. though, is inadequate for visibility in the critical rear and right front blind areas. Alternate Solutions All of these visibility aids as¬sume an attentive driver. In addi¬tion, areas such as the rear blinc, area are not covered. Based on the inadequacy of existing visibility systems, Anaconda made a com mitment to further the truck de¬tection technology. The best ap¬proach was considered to be ar active system. It would notify the haulage truck operator that an en¬croaching vehicle is present. Sev¬eral systems were considered, in¬cluding ultrasonics and elec¬tromagnetics. For the ultrasonic system, com mercial and in-house design were looked at. Designing an( building transducers with the spe cific beam shape to match the haulage truck blind spots re¬quired a major technological breakthrough. False alarms ap¬peared difficult to prevent en¬tirely. They were caused by pass¬ing, trailing, or leading vehicles a., well as nonthreatening objects. As a result of these problems, the ul¬trasonic technique was not pur sued. An alternative, an electro

Jan 7, 1982

By J. Wallace Gwynn

Salt from Great Salt Lake was probably used by the Native Americans prior to the Jim Bridger Expedition to the lake in 1824-25, and was used by the region&apos;s early explorers and trappers after that time. From the arrival of the Mormon pioneers in 1847, salt has been produced from Great Salt Lake, starting first with the collection of crude salt from along its shores, and later by boiling down the lake&apos;s brine to obtain crystalline salt. Since these early beginnings, salt production from the lake has become a substantial commercial enterprise. Since the early 1960s, research and development have led to the economic production of potassium sulfate, magnesium metal, chlorine gas, magnesium chloride products, and nutritional supplements. Many of the salt-production techniques and equipment that were developed prior to 1964 are still being used today. Sodium sulfate has been produced, but is no longer marketed. Morton Salt, Cargill Salt, and IMC Salt currently extract sodium chloride, which is precipitated during the early stages of evaporation when the brine concentration reaches saturation, or about 26 to 27 percent total dissolved solids. Magnesium Corporation of America produces magnesium metal and chlorine gas, and IMC Kalium Ogden Corporation produces potassium sulfate, as well as magnesium chloride brine and flake products. These salt, gaseous, and metallic products are processed from the sodium-chloride-saturated, high-magnesium-chloride brines, and from the potassium and magnesium salts that are precipitated from the lake brine after it has been further concentrated. One obstacle to salt production is the fluctuating level of Great Salt Lake. In 1983, the lake level began a dramatic rise from an elevation of 4,200 feet (1,280.16 m) to its historic high of 4.211.85 feet (1,283.77 m) in 1986-87 (uncorrected USGS provisional lake-level records). The State of Utah employed flood-control measures, including breaching the Southern Pacific Railroad causeway in 1984, and pumping lake water to a shallow basin west of the lake in 1987. During the high-water years, the lake&apos;s mineral-extraction industries faced many challenges including the need to raise dikes to prevent flooding of facilities, broken dikes which resulted in the inundation of solar ponds, and dealing with the lake&apos;s greatly reduced brine salinities which resulted in lower annual salt and concentrated-brine production. The years following the record-high lake levels have been a time of adaptation, innovation, and change for Great Salt Lake industries. After its solar ponds were flooded in 1986, AMAX, Inc. built a new solar-pond complex near Knolls, and used the concentrated brines from the West Pond, generated by the State&apos;s West Desert Pumping Project. Great Salt Lake Minerals built a 21-mile-long (33.8 km) open, underwater canal, called the Behrens Trench, to convey concentrated brines from a new, remote solar pond on the west side of the lake to the east side of the lake, to help increase its production of sulfate-of-potash. There were also numerous changes in corporate ownership and production-facility locations.

Jan 1, 2001

By M. Ramokhothoane, S. Rupprecht

"NTRODUCTION Women employment in the mining industry dates back to the 19th century. Various parts of the world, for example, India, Japan, the United Kingdom and the United States of America had women employed in large numbers. The women’s jobs were primarily manual in nature. Women were used to carry coal in buckets from the coal face and out the mine, and those who worked on the surface plants were used to sort waste rock from the coal product. Other heavy industries, which were traditionally male dominated, for example the military, also had a considerable number of women supporting the war effort. The outbreak of war also caused a shortage of labour, which in turn, necessitated that women were used in various roles during the war. After World War II, women returned to their traditional roles, but had acquired new skills, and had a different outlook to life. The wearing of pants and short hair became fashionable, as a result of being in the army.Various laws were passed which prevented the employment of women underground. Different countries had rules that they believed were in the best interest of women and were of the opinion that the rules somehow were protecting women against the harsh working conditions. In South Africa, post 1994, there has been a shift in thinking in regard to the employment of women in the mines. WOMEN IN SOUTH AFRICA MINING In the words of the Minister of Women in the Presidency, Minister Susan Shabangu, “women must take centre [sic] stage as the country gears itself for the implementation of radical socio-economic transformation policies and programmes in the next five years” (SA Government News Agency, 2014). In as much as some progress has been made in advancing women, more needs to be done in order to realize sustainable benefits in the economy. The emancipation of women is a reality and remains top of the South African government agenda. From the Authors’ experience there are two types of men in the mines. The first group support change and see the value in it. To them, women in mining bring in the diversity and play the complementary role in achieving greatness. There is no fear of job security and humiliation but a great sense of “camaraderie”. The other group continues to enforce stereotypes, which works against the spirit of redressing the imbalances of the past."

Jan 1, 2018

By Joseph M. Driscoll

After 30 years of successfully mining gold, Newmont Gold has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East Underground at the rate of 864 t/d (950 stpd). Annual production is more than 3.1 t (100,000 02). More than 70 underground miners will be employed during Carlin East&apos;s estimated six-year mine life. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed, cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive, and it is quantified as a confined or unconfined velocity. The confined velocity is more significant as explosives are usually used under a definite degree of confinement. This study evaluates the stepwise increment of the air-deck volume from 10 to 30 percent, and its effect on the VOD. The VOD estimation in the 172-mm-diameter explosive column was conducted using the Dáutriche technique. The air-deck volume increment has an attenuation effect on the steady-state VOD, and detonation failure is high at 30 percent air-deck volume. This attenuation effect is directly linked to the explosive’s rating and efficacy. The air-decking approach in this study is different from conventional air-decking techniques in that it does not employ the fixed blasthole parameters, air-deck volume and specific VOD. 

By Elnaz Saminfar, Jae Bateman, Eric Westergren, Mark Trim

This paper presents a case study of two major Australian infrastructure projects that used digital engineering to facilitate design delivery: WestConnex Project (Rozelle Interchange), and Sydney Metro West (Eastern Tunnelling Package). The paper presents project overviews and building information modeling (BIM) execution and focuses on modeling techniques, software utilization, data management strategies and how the digital models helped the design-build team mitigate impacts to schedule by identifying clashes between disciplines before the execution of work. Finally, it demonstrates the positive and transformative impact of digital engineering on the design and construction of large underground infrastructure projects and highlights its role in asset management throughout the project lifecycle.

Jun 23, 2024