Search Documents

By Richard E. Sabaski

The demand placed on the mining industry in the past 15 years for increased production, coupled with lower grade ore and higher cost capital, has resulted in a noticeable increase in grinding mill sizes. The pressure to increase mill size continues. During the mid sixty's and early seventy's, ?larger? conventional ball mills were in the range of 13 - 16-1/2 f t. diameter (4 - 5 m) increasing by the mid 70's to 18 ft. (5.5 m) diameter. At the same time, autogenous mills expanded from 24 - 32 ft. (7.3 - 9.1 m) to the present 34 and 36 ft. (10.b and 11.0 m) diameters. These size pioneers of 16-1/2, 18, and 36 ft. diameter mills from Allis-Chalmers have been free from structural problems, because they were analyzed, modeled, designed, and field tested to meet the challenge.

Jan 1, 1981

By Morgan M. Sears, Gamal Rashed, Michael M. Murphy, Brent Slaker

In this study, a parametric study was conducted using FLAC3D numerical models to examine the impact of oblique loading, generated from seam dip, on the strength and the failure propagation pattern of a stone pillar using two simplified geometry types. In type 1, the sidewalls of the pillars were assumed to be perpendicular to the roof and the floor, while in type 2, the sidewalls of pillars were assumed to be vertical. The complex pillar geometry in dipping mines was frequently modeled using these two geometries. To capture a complete picture of the effect of seam dip on pillar stability, the modeled width-to-height (W/H) ratio of the pillars, in situ stress field, and pillars roof/floor interfaces were systematically varied to account for the potential distribution of values for these parameters across the underground stone mines in USA. Results from the numerical modeling indicate that dipping pillars have reduced strength compared with horizontal pillars. Also, an asymmetric failure propagation pattern could be obtained depending on an interaction between the W/H ratio, seam dip, in situ stresses, and pillar geometry.

Feb 5, 2021

By Jesse L. . Jr. You

Tunnels in the granitic Climax stock at the Nevada Test Site were inspected for keyblock occurrence. Thirteen relatively large pyramidal keyblocks were located in about 230 m (750 it) of tunnel. Orientations, dimensions, joint roughness coefficients, and joint compressive strengths were measured for the faces of nine keyblocks. The measurements were used to back-analyze keyblock stability to check the validity of a numerical model for keyblock behavior. A newly developed three-dimensional numerical model correctly predicted whether or not each keyblock failed in six of eight cases. The two exceptions involved stress conditions and keyblock locations that clearly violated the assumptions that underlie the stability model. The observations also allowed the effect of tunnel orientation on keyblock occurrence to be evaluated. Of the thirteen observed keyblocks, nine large blocks were found in less than 30 m (100 ft) of the Piledriver drift (which runs N56E) while only four blocks of comparable size were observed in 200 m (656 ft) of the Spent Fuel Test--Climax drifts (N61W). The orientations of the keyblock faces were checked against known discontinuity set orientations; some of the faces correlated well with mean set orientations, whi.le other faces were fringe members of sets. Stereographic techniques were used to examine the frequency of keyblock occurrence and to determine the maximum keyblock size that could be encountered with a given combination of discontinuities. Keyblock occurrence was found to be affected by tunnel orientation in a predictable way; this can be used to guide or improve tunnel design practices.

Jan 1, 1986

By M. Paul

"INTRODUCTION In 1990, the uranium production of SDAG Wismut in East Germany was stopped. 45 years of inconsiderate destructive exploitation had scarred both landscape and nature. With the “Wismut law” which came into force in December 1991, the Federal Republic took responsibility of the remediation of the legacies from former uranium ore mining and milling in Saxony and Thuringia. A unique opportunity turned out in order to remove environmental damage, to enhance the life quality of the local population, to shape new landscapes and to advance the economic restart. (1) The results of nearly 25 years of remediation activity are evidence that this opportunity was used at all former SDAG (Sowjetisch-Deutsche Aktien-gesellschaft) Wismut sites. The reference project “Wismut“ has evolved into a joint project of all parties involved and radiates beyond the affected regions. This is particularly reflected by the Know-how transfer starting from Wismut and the increasing activities for third parties abroad.WATER MANAGEMENT AT WISMUT REHABILITATION Within the Wismut project, water management and conventional technical water treatment are by far the most cost-intensive long-term tasks of the remediation programme. Over the medium term, there is no viable alternative to the operation of active systems to catch and treat contaminated mine waters at the Ronneburg, Schlema, Königstein, Pöhla, Seelingstädt and Helmsdorf sites. Based on the status quo, this paper outlines the key issues of the Wismut GmbH water management strategy over the medium and long term. It is focused primarily on achieving protection goals for potentially impacted water bodies in the surroundings of Wismut sites and on optimising associated remediation expenditures as well as on creating the prerequisites for achieving low post-remedial care and maintenance or walk-away system status over the long term. (2) The applied mining practices during the active SDAG Wismut period have not been up to the high standards of modern mining operations and their requirement to leave former production premises and deposited residues in a condition that was not only physically but also chemically stable. Rather the emission of mine and seepage waters laden with high acidity, metal and salt content is a frequent corollary and difficult legacy of historic mining and processing operations (4, 5). As a consequence, the control or mitigation, respectively, of environmental impacts associated with contaminated mine waters ties up enormous public resources worldwide (6, 7)."

Jan 1, 2016

By Panshi Xie, Yingyi Zhang, JIANJIE DUAN, Shenghu Luo

A multi-layer gangue roof of a steeply dipping coal seam with a large mining height face area was analyzed using physical simulation, numerical simulation, theoretical analysis, and field measurement methods to evaluate the roof deformation and the mechanisms associated with the instability of the hard gangue and soft coal interlayer. The results indicated that the first weighting step of the multi-gangue roof was larger than that of a non-gangue roof, but periodic weighting steps were similar. The overburden collapse height was lower in the multi-gangue roof than in the non-gangue roof due to the buffering and supporting function of the collapsed gangue. Moreover, the failure of the coal interlayer was the key factor in the collapse of the multi-layer gangue. A mechanical model was established for the hard gangue and soft coal interlayer based on a revised Prandtl squeezing theory. The limited load of the interlayer and maximum resistance of the shield support was thusmodeled. The maximum resistance of the support increased with the dip angle of the seam and burial depth. It also increased with the interlayer thickness at thicknesses below 2.75 m. It reached a peak when the interlayer thickness was between 2.75 and 3 m and exhibited a decreasing trend when the thickness was greater than 3 m. The results were confirmed using physical simulation and a field test. Certain measures were proposed to control the stability of the gangue roof, including zoning control of the mining height and resistance and advancing the support while maintaining roof contact, thus ensuring the integrity of the support and surrounding rock system.

Jun 30, 2020

Micro-computers have made it practical to install a high-speed acquisition system to collect data from a longwall face in near real-time. By simultaneous data analyses using neural networks and fuzzy sets, information regarding longwall mining performance and underground behavior can be provided and forecasting longwall instability and detecting geological anomalies is feasible. This paper presents details of the application of neural networks and fuzzy sets in developing on-line evaluation of longwall roof behavior. Techniques for interpreting longwall shield pressures and characterizing roof conditions are discussed.

Jan 1, 1996

By M. Scaggs, L. R. Mendoza

"On January 9, 2014, a large chemical spill occurred on the bank of the Elk River near Charleston, WV. Within hours, the potable water supply for more than 300,000 people was contaminated, and the incident captured national headlines for weeks. Although the primary chemical, crude 4-methylcyclohexanemethanol, or MCHM, is deemed nonhazardous, the impacts of the spill are significant – with all stakeholders, including the public, members of industry, and relevant government agencies experiencing losses. This case highlights the need for a more proactive approach to environmental management, shifting from crisis control and remediation to crisis prevention and risk management. INTRODUCTION On the morning of January 9, 2014, approximately 10,000 gallons of crude 4-methylcyclohexanemethanol (MCHM) leaked from a 48,000-gallon storage tank sitting on the bank of the Elk River near Charleston, West Virginia (WVDEP, 2014; CSB, 2014). MCHM is a chemical commonly used in preparation of fine coal, and is deemed nonhazardous in terms of transportation and storage regulations and also toxicity (CDC, 2014a). Freedom Industries, Inc., a producer and vendor of specialty chemical products, had acquired the storage facility where the spill occurred from Etowah River Terminal, LLC just a few weeks prior in December 2013 (WVDEP, 2014; Freedom, 2005). The direct cause of the spill was ultimately determined to be two small holes in the base of the 76-year-old tank, which were created due to corrosion damage (Bauerlein & McWhirter, 2014). The spill site was located just over a mile upstream from the intake of a municipal water treatment facility operated by West Virginia American Water (WVAW), which serves a population of 300,000 across nine counties in central West Virginia (CDC, 2014a). In a matter of hours, the leaked MCHM made its way through the treatment facility and into the water of nearby homes and businesses, where its strong smell was noticed almost immediately. On the evening of the spill, WVAW concluded that its conventional treatment processes, which include carbon filters to remove a variety of contaminants from water, were not capable of fully removing the MCHM and a “Do Not Use” order was issued for all customers (WVAW, 2014a). With little information readily available regarding the potential human health effects of MCHM, the US Centers for Disease Control and Prevention (CDC) quickly issued an advisory ruling that set a maximum screening level of 1 ppm for safe drinking water (CDC, 2014a). Based on this recommendation, the “Do Not Use” order remained in effect for a total of eight days, until January 17, when the WVAW distribution water was confirmed to have MCHM concentrations below this level (WVAW, 2014a). However, due to the pungent odor of the chemical, its presence was still recognizable in the WVAW facility and in consumers’ tap water after the order was lifted (Manuel, 2014). Recent studies have shown that the chemical can be detected in water at concentrations as low as 0.55 ppb by individuals experienced in odor identification (Rosen et al., 2014); and even individuals with no such training can detect pure MCHM at just 7 ppb (WVTAP, 2014). The fact that this chemical can be sensed at such low levels – indeed far below those considered safe – undoubtedly added to growing public concern. In response to numerous complaints and demands, WVAW continued flushing the treatment facility and pipes until February 25 when MCHM levels were measured below 2 ppb (WVAWb, 2014), and eventually replaced the affected filter media (WVAWc, 2014)."

Jan 1, 2015

By Mads Aniksdal

New Nedre Fiskumfoss is a construction project in North Trøndelag, Namsen River. The purpose of the contract is construction of a new hydropower plant, that will phase out the existing power plant in the same waterfall. The contract consists of a tunnel system with cross sections from 16 m2 to 150 m2, powerhouse and transformer in rock caverns, 6 shafts and major works with inlet and outlet below river level. Technical challenges consist of demanding design on rock extraction, cofferdams, solid constructions with challenging design and demanding rebar work, as well as restrictions and unpredictable water flow in a national salmon river.

Jun 13, 2023

By S. P. Fleming

An acid mine drainage sludge containing 0.26% nickel, 0.21 % cobalt and 4.5% manganese was leached in a one-liter reactor with sulfuric acid in the absence and presence of sodium sulfite. The effects of temperature (25°C and 52°C) and sodium sulfite concentration (up to 0.03 molar) on the leaching rate were particularly investigated. The leaching rates of nickel and cobalt with sulfuric acid have been determined to be controlled by diffusion through product layer. It has been found that effective leaching conditions to give more than 90% extraction of nickel, cobalt and manganese while keeping the iron extraction below 10% come with an elevated temperature and a low sodium sulfite concentration at pH 3; for example, 52°C and 0.01 molar sodium sulfite.

Jan 1, 1992

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents the preliminary test results obtained using a 0.38-kg/s (3,000-lb/hr) beta prototype MagMill. In processing Upper Freeport coal, the beta prototype recovered 82 % of the weight of the feed and 91 % of the heat content while reducing the potential emissions of sulfur by 61%. Pyritic sulfur in the MagMill product was reduced by 78% compared with that in the feed. For all runs, the mill product particle size was controlled to between 70% and 80% -741m (200 mesh). Recoveries of mercury, arsenic and selenium ranged from 35% to 45% of the amounts found in the feed. Power draw was reduced by 26%, and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2002

By T. Brozell

"Communities near sand mines and processing facilities in Wisconsin have raised concerns regarding possible exposure to ambient respirable (PM4) crystalline silica. Fenceline PM4 (particulate matter captured with a 50 percent cut size of 4 micrometers aerodynamic diameter) crystalline silica concentration data were compiled at Fairmount Santrol Inc., Mathy Construction Inc. and U.S. Silica facilities. The long-term average PM4 crystalline silica concentrations ranged from 0.05 to 0.45 micrograms/m3 when sample values below the limit of quantification were treated as zeros. All of the long-term average concentrations were less than 20 percent of the Minnesota Department of Health’s and California Office of Environmental Health Hazard Assessment’s PM4 crystalline silica chronic reference exposure level of 3.0 micrograms/m3. The measured concentrations were consistently within the local background concentration range.Air Control Techniques P.C. compiled the sampling data using Thermo Fisher Scientific Inc. Partisol 2000i PM2.5 samplers meeting the requirements of 40 CFR Part 50, Appendix L. These samplers were adapted to capture particulate matter with a 50 percent cut size of 4 micrometers. The use of polyvinyl chloride filters allowed for crystalline silica X-ray diffraction analysis by NIOSH Method 7500. The combined use of adjusted PM2.5 filter-based samplers with Method 7500 crystalline silica analyses provided for a highly sensitive limit of quantification of 0.31 micrograms/m3 of PM4 crystalline silica.BackgroundIn 2005, the California Office of Environmental Health Hazard Assessment (OEHHA, 2005) adopted a 70-year chronic reference exposure level (REL) for PM4 (particulate matter having aerodynamic diameter of 4 micrometers or less) crystalline silica. The REL was extrapolated from occupational hygiene epidemiological studies, essentially all of which were based on in-plant PM4 crystalline silica measurements. No well-established ambient sampling technique for PM4 crystalline silica was available at the time that OEHHA adopted its REL. The personal samplers used for the National Institute for Occupational Safety and Health (NIOSH) Method 0600 in-plant sampling of employee exposure were designed for concentrations higher than ambient levels. The limit of quantification (LOQ) of PM4 crystalline silica on NIOSH 0600 filters was too high for the effective sampling of ambient air."

Jan 1, 2015

By Liuming Wu, Willis Forsling

The complexation of Alizarin Red S (ARS) at the surface of hydrous fluorapatite particles has been investigated at 25.0 C by means of potentiometric titrations, adsorption experiments in 0.1 M NaCI ionic medium, and Diffuse Reflectance Infrared Fourier Transform spectroscopy (DRIFT) studies. A chemical model describing the reaction at the aqueous mineral surface has been established under equilibrium conditions according to the reaction [== -CaOH2 + HA2 - « _ =PO CaA2 - z + H30&apos;; to (int.) = -5.61 ± 0.02 3 a =PO- logBs-1110(int.) ( ) within the range 8.40 <_ -log[H ] <_ 9.80.] Experimental data were evaluated using the computer program FITEQL on the basis of a constant capacitance model for the electric double layer. The surface complex structure, has been proposed to involve the quinoid and alpha phenolic oxygens of ARS coordinated to the calcium sites on the fluorapatite surface.

Jan 1, 1993

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and nonfatal injuries that occur in mining in the United States. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the U.S. Mine Safety and Health Administration (MSHA) from 2010 through 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84 percent involved the workers not using fall protection, fall protection not being provided or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment or working near highwalls. In most cases, a single, basic, corrective action — such as using fall protection — would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.

By Verya Nasri, Agustin Rey

Once completed, the Montreal Réseau Express Métropolitain (REM) will be the fourth largest automated transportation system in the world. The REM represents construction costs of approximately 7.0 billion Canadian dollars. The project consists of 67 km of twin tracks over four branches connected to downtown Montreal. The project includes 26 stations with 3 underground stations in downtown Montreal. One of the underground stations was built using the NATM method with thin permanent shotcrete initial and final liners separated by a sprayed on waterproofing membrane. The 2 other underground stations were built with the cut and cover approach including one using permanent secant pile wall with permanent walers and struts as the support of excavation and the final perimeter wall of the station. The project also includes the rehabilitation and enlargement of the Mont Royal Tunnel. This 100-year-old double track tunnel is about 5 km long. The REM also consists of 3.6 km new TBM tunnel connecting downtown to the Montreal International Airport through saturated soft ground and karstic rock. By the time of RETC, the construction of REM underground structures will be completed. This paper presents the design and construction aspects of the underground structures of this mega project.

Jun 13, 2023

By E. H. Kurt

INTRODUCTION The simplest way to drill a hole into rock is to strike a steel chisel or drill bit with a hammer. Early miners used this elementary hand technique so successfully in "single jacking" and "double jacking" that the first mechanical rock-drill designers sought to duplicate it. However, in the early developments, the designers were forced to retreat to a construction known as the "piston drill," wherein the entire drilling element is tied to the piston and reciprocates with it. It took nearly 50 years to devise a method of divorcing the two elements and to achieve the original hammer principle used in hand drilling. The Mont Cenis tunnel, drilled through the French Alps in 1861, usually is considered the birthplace of the mechanical rock drill. The Hoosac tunnel in Massa¬chusetts was drilled at about the same time, and the success of these two ventures paved the way for innova¬tions that produced the Burleigh, Ingersoll, Sergeant, and Waugh piston drills between 1870 and the turn of the century. In 1897, George Leyner of Colorado introduced what has been considered the most significant development in rock-drill history. He devised the hollow drill steel for water flushing; when combined with his free-piston hammer drill, this became the first lightweight and dust¬free underground machine. In addition, Leyner&apos;s drills introduced improvements such as automatic rifle-bar rotation of the drill steel and chuck, automatic lubrica¬tion, and an enclosed throttle control. During the 1920s and 1930s, automatic feeds, centralizers, sliding cones, and the automatic water back head were developed, laying the groundwork for all pneumatic underground drills currently in use. Since these pioneering efforts, rock-drill development has been concerned primarily with refining the designs and improving the metallurgy to make faster, lighter, and more dependable machines. Fig. 1 illustrates the progress in drilling speed during the first 125 years of rock-drill development; that progress is a credit to the persistence and inventiveness of the designers in the rock-drilling industry. ROCK-DRILL CLASSIFICATIONS To meet the variety of conditions encountered in rock drilling, several distinct types of drills have been de¬veloped. In general, rock drills may be classified as either hand-held or mounted, with the hand-held ma¬chines including the jackhammer or sinker, the jackdrill or jackleg, and the stoper. The mounted drills are com¬monly known as "drifters." Table 1 shows that each type of drill is available in several sizes from different manufacturers. Fig. 2 illustrates a typical rock drill, showing the principal components. The jackhammer or sinker, shown in Fig. 3, is used primarily for general mine utility work such as drilling anchor holes (short vertical holes to bolt or anchor machinery), pin holes (short, usually horizontal holes to fasten sheaves, etc. to side walls), popholes (for blasting large boulders), and similar applications. They also are used for shaft sinking. Jackhammers are classified ac¬cording to weight, and they range from 7 to 30 kg (15 to 65 lb). The rock drill originally known as a jackleg was made by clamping a pneumatic cylinder or leg to a jack¬hammer, both to support the weight of the machine and to feed the tool forward in horizontal or uphole work. The more modern jackdrill refined this concept to make the hinged pivot for the leg integral with the drill cylinder and to group all drill and leg controls in the drill back head for convenience. Fig. 4 illustrates a typical jackdrill. Jackdrills are classified according to cylinder bore size, ranging from 60 to 83 mm (2.375 to 3.25 in.). Because of their light weight and versatility, jack drills are very effective in small drifts, small tunnel head¬ings, and stoping. The larger machines are applied to hardrock formations and in applications where drilling speed is a primary consideration. In soft formations or

Jan 1, 1982

By N. E. Norman

The big hole drilling industry is a relatively new one. In fact, very little big hole drilling was done prior to 1950. If there is to be a marriage between big hole drilling and mining, we should certainly take a look at the background of the big hole drilling industry. Let us examine the three main features of big hole drilling and determine how each applies to mining. Let&apos;s also look at the good qualities and the limitations of each of these character traits.

Jan 1, 1968

By James H. Barks

Exploration for ore deposits in southeastern Missouri in the 1950&apos;s resulted in the important discovery of lead, zinc, copper and silver in 1955. Further discoveries in the area led to the naming of the Viburnum trend. It has sometimes been referred to as the "New Lead belt" to distinguish it from older lead-producing areas to the east. As presently developed, the "trend" is 35 miles long, running north and south about 50 miles west of the Lead belt. Galena (lead) is the principal ore mined, with lesser quantities of sphalerite (zinc), chalcopyrite (copper) and silver recovered as economic by-products. The ore body is as much as 140 feet thick and 1,200 feet wide, and is found in the Bonneterre Dolomite (Upper Cambrian) at depths ranging from 700 to 1,200 feet. Since its discovery many companies have engaged in exploration and several major companies have developed new mines and constructed mills and a smelter in the area. The first mine in the Viburnum trend came on stream in 1960, but as more mines came on stream and others reached capacity, lead production increased to the point that the Southeast Missouri Lead district produced 432,576 tons of lead in 1970 to become the world&apos;s largest lead-producing region (Missouri Geological Survey and Water Resources, 1971). The Viburnum trend area with its rolling, heavily forested hills and numerous clear running streams is in the Clark National Forest of the Missouri Ozarks. Until the recent development of its mineral resources, the area was sparsely populated and nearly unmarked by the activities of man. Industrial development is almost certain to be accompanied by environmental changes. In a day of growing awareness of the need to preserve the quality of the

Jan 1, 1971

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The forestry reclamation approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22 m (4 ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes (i.e., greater than 23°) could lead to slope failures, which is one of the issues that the Surface Mining Control and Reclamation Act of 1977 (SMCRA) sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. During this first phase of investigation, there has been no major mass movement of the slope and slope stability analysis indicates that the application of the FRA has little impact on the overall stability of the slope. Mining Engineering, 2011, Vol. 63, No. 12, pp. 55-62. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

"In addition to outstanding technical sessions and networking opportunities, the SME Annual Conference and Expo offers attendees a chance to see the latest and greatest technology that the industry has to offer. The 2017 SME Annual Conference and Expo was no exception as 575 companies filled 756 booths from Feb. 19-22 in Denver, CO. The following is a look at some of the vendors that were on hand.AIL MiningThe Edge, featured by AIL Mining at the 2017 SME exhibit, is a four-flange structural liner designed to be an alternative to structural plate’s traditional lapped seams and to help mine operators build more efficiently and safely. It is ideal for creating underground structures, such as mine shafts, ventilation raises and escape ways. The Edge is available on SuperCor structural steel plate — 10 times stiffer and five times stronger than traditional steel liner plate. It facilitates curved structures, both horizontal and vertical, and eliminates the need for ring beams. It is ideal for remote sites. For added safety, structures can be assembled from the inside, and the leak-resistant structures can be dismantled and removed easily. Brackets can be attached to mine shafts or vent raises to support Alimak rails or climbers. Similarly, brackets or hangers can be attached to drifts or tunnels to support mine air, water or electrical utility services.ArcadisMining companies spent nearly $12 billion on water infrastructure worldwide in 2014, reflecting the industry’s heightened concern about environmental issues and social, regulatory and political risks.So, with an increasing focus on water reuse and recycling, mining companies must have effective water management plans that include sustainable solutions. Also, many water quality issues fall under both state and federal regulatory jurisdictions. To solve these problems, Arcadis provides comprehensive ground- and surfacewater technical support in a complex hydrogeologic setting. It can characterize the nature and extent of mine-related constituents in ground water and surface water, as well as the complex interactions between the two waters, and prepare the operational permits needed by mine and tailings facilities. As an example, Arcadis constructed a hydrogeologic and geochemical conceptual site model that improved site understanding for a molybdenum mine in the western United States that spanned several watersheds. It also provided technical support for permitting and compliance issues, allowing the mine to return to active production."

Jan 5, 2017

By R. M. G. Machunter

The presence of ultra-fine particles affects the separation performance of wet gravity separation equipment. Several studies have been undertaken to establish the maximum level of these particulates that can be tolerated by spiral separators and it has been found that unless the ultra-fine material is effectively processed, relatively low proportions in the ROM material combined with high feed rates can result in degradation in plant performance and/or excessive water consumption. The maximum level of particulate material in the process water has been determined by examination of separation performance of spiral separators under varying slime loading. This work has been conducted utilizing various feed sources and a robust ‘rule-of-thumb’ has been derived.

Jan 1, 2005