Search Documents

By Antti Porvali, Vivek Agarwal, Mari Lundström

Hydrometallurgical recovery of rare earth elements (REE) from NiMH battery waste can be performed using sulfuric acid leaching followed by selective precipitation as double salt (REENa(SO4)2·H2O) by adding Na2SO4 as a precipitating agent. The formed double salts can then be further converted with NaOH solution to form REE hydroxides. However, present literature has paid little attention to how to minimize the consumption of reagents in this recovery process. In the current study, a process model was built using HSC Sim software, and metamodeling of the simulated flowsheet was conducted with the design of experiments (DOE), after which the basic functionality of the flowsheet was verified by experimental work, starting from sulfuric acid leaching of spent batteries. As the process is based on chemical circulation internally in the process, the objective was to investigate the accumulation of the elements in solution, specifically Na+ , K+ , SO4 2− ions and impurities liberated in the NaOH conversion step. It was found out that metamodeling could be utilized in obtaining first estimate of the process behavior, prior to any experiments. Flowsheet functionality with circulated solution was confirmed, obtaining at best 96.9% La recovery.

By Robert Labbe

The final tunnel lining for this project involved pumping vast quantities of concrete over large distances under the extremely busy streets of lower Manhattan. Approximately 68,000 cubic meters (89,000 cubic yards) were pumped from various locations over 152 meters (500 feet) below ground (Figure 1) to create nearly 14.5 kilometers (9 miles) of 3.05 meter (10 foot) diameter tunnel. Total distances pumped exceeded 1,645 meters (5,400 feet) horizontally after a vertical difference of over 152 meters (500 feet). The urban setting of the operation, coupled with the long distances over which concrete was pumped, created many problems which had to be dealt with along the way. A three-shift labor operation was implemented to allow sequential pouring of tunnel sections nearly every day. The fine tuning of the mix design was critical to make this operation successful.

By David K. Hylbert

This study investigated roof falls in room-and-pillar drift coal mines in eastern Kentucky and utilized geologic methods for predicting roof conditions in advance of mining. In the Highsplint mine, the roof was classified in four categories or conditions: Condition A and B (Laminated Shale), Condition C (Rolling Sandstone with Shale in Pockets) and Condition D (Zone of Major Sandstone Roll(s)). Structure contour and isopach maps of the Darby coal bed and associated immediate roof rocks were used to project axial trends of the sandstone roof. Trend mapping in the mine and on outcrop provided more detailed control for roof projections.

Jan 1, 1978

By C. G. Buttleman, W. C. Brice

In Minnesota, reclamation of active aggregate mining sites is primarily regulated through local permits issued at the county, township, or municipality. However, for abandoned or depleted aggregate mining sites, a responsible party for reclamation is often no longer available. Since 1995, the Minnesota Department of Natural Resources has reclaimed several abandoned aggregate sites using innovative public/private partnerships and emphasizing native plant materials. The purpose of these projects is to demonstrate cost effective reclamation methods that can be utilized by both aggregate operators and local government and to promote mine planning and resource identification as it relates to reclamation.

Jan 1, 2000

By I. Demers

Doyon mine, Quebec, Canada evaluates the possibility of desulphurizing their tailings to produce material to be used in as cover over the acid generating tailings disposal site. Laboratory tests were conducted and showed that a single-layer cover made of desulphurized tailings placed over reactive tailings can prevent the generation of acid mine drainage. Modelling with the software Vadose/W was undertaken to optimize the design parameters, namely cover thickness, water table position, and residual sulphide content of desulphurized tailings following laboratory work. It was found that the optimal configuration includes a 1 m desulphurized tailings cover containing 0.8%S, with the water table kept at the interface between the reactive tailings and the cover. To maintain the cover performance to reduce oxygen flux towards acid-generating tailings even in the event of a long dry period, a sand layer is suggested to protect the cover from excessive evaporation. It is possible to reach the environmental objective chosen for Doyon mine (10 mol/m2/year) with the protective sand layer, even in extremely dry conditions.

Jan 1, 2008

By K. Burke, G. Zhan, A. Mayer

A cover with capillary barrier effects (CCBE) is being constructed on the AA Leach Pad at the Barrick Goldstrike Mine site near Carlin, Nevada. The purpose of the cover is to eliminate/minimize infiltration of meteoric waters into the leach pad. Laboratory and numerical analyses indicate that Carlin Formation siltstone (TCS), a locally available material, has the necessary hydrologic characteristics when placed on the leach pad to act as a CCBE. A pilot study has been conducted on a small-scale test cover placed on the AA Leach Pad to examine the cover performance under irrigated conditions. The preliminary test results demonstrate that the designed cover is capable of preventing meteoric water infiltration.

Jan 1, 2001

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey's test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

Jun 17, 2019

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey’s test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey’s test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

By Ulf G. Gwildis

The Bright water Conveyance System includes 21 km of tunnels mined by two earth pressure balance Tunnel Boring Machines (TBMs) and two slurry TBMs. The probabilistic baseline approach defined in the Geotechnical Baseline Report (GBR) can representatively be verified by use of a comprehensive tracking system to identify face conditions that allows comparison with the baselines. The glacial geology includes a high lateral variation in soil types that, when combined with the pressurized face tunneling methods, creates challenges for documenting face conditions. Baseline tracking using spoil samples and TBM operational parameters provides information to document actual conditions and support resolution of differing site condition claims.

By Laurens de Jonge, Wiebe Boomsma, Rodney Norman, Stanislav Verichev

"Earth provides natural resources, such as fossil fuels and minerals that are vital for human life. As the global demand grows, especially for strategic minerals, commodity prices rapidly rise. Thus there is an identifiable risk of increasing supply shortage for minerals. Hence a major element in a long-term economic strategy must be, to ensure security of supply for these strategic minerals. In this rapidly changing global economic landscape, deep sea mining has gone from a distant possibility to a likely reality within just a decade.Although deep sea minerals extraction was investigated in the 1970’s, it was abandoned because of changing commodity economics, advances in on-land exploration techniques, growing concern on environmental impact, and political and legal aspects with regard to ownership issues. The developmental data from those days, if still available, are not adequate to allow engineering and building of an integral system for extraction of deep sea minerals without additional R&D work. Thus, deep sea mining is yet to attain a Technology Readiness Level (TRL) sufficient to successfully undertake deep sea mining operations, from resource discovery to resource assessment and to resource exploitation [Blue Mining, 2014]."

Sep 1, 2014

By V. L. Ketellapper

This paper discusses the technical issues and stakeholder collaborative processes which resulted in achieving a balance between the reclamation of abandoned mine sites, providing affordable housing, and preservation of open space at the French Gulch Site. Through this process, it was discovered that mine site reclamation would need to be conducted in conjunction with two priorities for community sustainable development: providing affordable housing for locals who work in the resort town of Breckenridge, and open space preservation. It was found that conducting these activities concurrently would result in providing resources necessary to complete mine site reclamation. The first phase of the affordable housing development is almost completed. This development resulted in redevelopment of mining impacted lands and was recognized by the U.S. Environmental Protection Agency (EPA) with a National Smart Growth Award in 2002.Negotiations are also underway to preserve the remaining 1,800 acres of land held by the mining company as open space. This transaction will in turn provide resources to address water quality issues associated with mine discharges.

Jan 1, 2004

By D. Nutakor

Rock joint stiffness is not only a poorly known parameter, but also has no established laboratory measurement procedure. This paper presents methods used to determine the normal and shear stiffnesses of healed joints filled with vapor-altered minerals obtained from the Yucca Mountain site in Nevada. Results show that these joints behave linearly up to 85% of their loading history and are stiff with strengths very close to the strength of the intact rock. Factors that might have contributed to the linear behavior of these joints are discussed and areas requiring further investigation are provided. Joint normal stiffness ranges from 7.16 to 64.77 GPa/mm with an average value of 26.93 GPa/mm, while joint shear stiffness averages 11.41 GPa/mm and ranges from 3.09 to 28.41 GPa/mm. Young?s modulus of the vapor-altered joint infilling was calculated from the stiffness of the healed joint. Young?s modulus of the vapor-altered joint filling material averages 7.89 GPa and ranges from 2.15 to 19.43 GPa. Given the pervasive presence of such altered rock, usually in the form of sub-spheroidal 3-D pockets, this property should be of value in any numerical modeling attempting to describe the mechanical behavior of these tuff formations at the level of detail where inclusions might be a factor.

Jan 1, 2008

By G. C. Hall, B. E. Hobbs

Giant gold deposits are considered products of crustal-scale systems. Reduced fluids stored in mid to lower crustal reservoirs were discharged into mid to upper crustal sites of deposition. Elements of the architecture include crustal-scale structures, reduced packages of rock and regional seals. Gas-rich aqueous fluids were common but non-aqueous fluids may have been significant in the deeper parts of the systems. Fluid fluxes in over pressured domains were maintained by porosity waves. Abnormal heat input from the mantle may not be required once the systems were perturbed. Fluid-mixing and hypogene enrichment were probably the most significant precipitation processes.

Jan 1, 1999

Minerals are fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels?mining, processing and manufacturing finished products. The estimated growth rate for the real GDP of the United States was 2.1 percent and the nominal GDP was about $13.8 trillion in 2007 (Table 1). The prime interest rate decreased to 7.25 percent in December from 8.25 percent at the beginning of 2007, reflecting actions taken by the Federal Reserve Board to counter financial difficulties surrounding subprime mort-gages. Delinquencies on subprime mortgages increased throughout the year, affecting not only the delinquent home owners but also financial instruments invested in mortgage-backed securities. The average contract mortgage rate for the purchase of previously occupied homes in the United States was 6.35 percent in November; a slight decrease from 6.37 percent in January but still greater than 5.34 percent reported in July 2003, the lowest rate in the past five years. With the tightening of credit, the seasonally adjusted annualized rate for new privately owned housing starts declined 27 percent from December 2006 to November 2007. The loss in the residential market was balanced by a 9-percent increase in nonresidential construction between January and August 2007, during which slight increases occurred in nearly all

Jan 1, 2008

By G. Deissman, S. Kistinger

For the last 15 years environmental Life-Cycle Assessments (LCA) have increasingly been used to evaluate the environmental performance of industrial processes and products and have been employed as a basis in decision making processes in the public and industrial sector. However, assessment methodologies for environmental protection measures and reclamation/remediation measures with respect to their consumption of natural resources are generally poorly developed. In this presentation a methodology for LCA of environmental protection measures and remedial actions, respectively is suggested, using the remediation/reclamation of mining sites as an example. Key aspect of this approach is the development of an evaluation method appropriate for environmental protection measures, which links the various impact indicators recognised in the impact assessments and allows their integrated assessment.

Jan 1, 2005

By D. R. Zuchelli

In order for MSHA to require the use of a noise control, the control must be proven ?technologically feasible?. Technologically feasible controls must reduce a miner?s noise overexposure to the permissible exposure level (PEL) or achieve at least a 3 dBA reduction in the miner?s noise exposure. The miner?s total noise exposure should be examined from an occupational viewpoint and not solely on a machine or equipment basis. This examination requires a field evaluation of the occupation as opposed to an equipment test conducted in a laboratory. The operator of a Hilti TE MD20 LS electro-pneumatic drill realized a full shift noise exposure (TWA8) reduction exceeding 8 dBA as compared to when operating a Gardner Denver S83F pneumatic jackleg drill while installing an equal number of drill holes into the Idaho Springs Gneiss rock formation. However, the Hilti drill?s penetration rate was only 27% of that of the jackleg drill. Although the Hilti drill was proven to be technologically feasible as a noise control, its slower penetration rate would require its economic feasibility to be evaluated on a case-by-case basis.

Jan 1, 2011

By William M. Dowall

The recently completed in-pit crushing and conveying project at Phelps Dodge's Morenci Mine is rated among the world's leading materials handling projects. The operation involves the crushing and transport of more than 109 kt/ d (120,000 stpd) of copper ore, using regenerative conveyors capable of providing more than 5.5 MW (7000 hp) of equivalent electrical energy. The Morenci Mine is located 330 km (200 miles) east of Phoenix, AZ. Phelps Dodge Corp. owns an 85% interest in the mine. The remaining 15% is owned by Sumitomo Metal Mining Co., Ltd. and Sumitomo Corp. Copper has been continuously produced from the Morenci district since the late 1800s. Until 1989, run-of-mine ore was transported from active mining faces to the Morenci and Metcalf concentrators by truck and rail haulage. In that year, a system of in-pit, semi-portable crushing plants and overland conveyors was commissioned. This substantially reduced truck haulage and effectively eliminated rail haulage in the pit. The system used two semi-portable, in-pit crushing stations equipped with 60/89 gyratory crushers. The crushed ore from both plants reported to the first of two overland belt conveyors, arranged in series, for transport from the pit to a coarse ore stockpile. The system was "backed-up" by existing locomotive rail haulage.

Jan 1, 1993

By MATT RENAUD, Mustafa Kumral

As high-quality mineral deposits are thoroughly exploited, mines of the future will have to move towards more remote and lower quality projects. With these projects comes an increased business risk to the operator. Even now, mining companies often turn to foreign countries for new deposits to produce, introducing the concept of country risk into their portfolio. Furthermore, feasibility studies often fail to accurately quantify the risks associated with various projects, and as such, this study proposes a technique of risk quantification which can both aid mining companies to evaluate the viability of investment and assist in risk disclosure to public investors for the mining industry of the future. This paper aims to quantify the effects of country risk on the valuation of potential mining projects, using a combination of modular and risk-weighting techniques to evaluate the country risk premium (CRP) required to obtain capital for operation of risky foreign mining projects. The techniques proposed in this paper are demonstrated using fictional examples and then evaluated for accuracy against a recently developed debt-funded precious metal project in a country in the Americas.

Sep 30, 2021

By Edward Thomas

Yucca Mountain Overview The U.S. Department of Energy?s Yucca Mountain Project is a geologic repository project designed to receive, handle, package, transport, and emplace spent nuclear fuel and high level radioactive waste. The planned repository would be located in Yucca Mountain on the western edge of the Nevada Test Site, about 90 miles northwest of Las Vegas, Nevada, and would include both surface and subsurface areas. Yucca Mountain rock formations consist of successive layers of volcanic rocks (called tuffs) approximately 14 to 11.5 million years old, formed by eruptions of volcanic calderas to the north. With the volcanic rock the potential for methane emission is not an issue and the subsurface repository is a non-gassy (methane) classification. This paper will provide a summary of the development ventilation system design that provides fresh air for subsurface construction activities, and the emplacement ventilation system design that removes heat generated by the waste packages. The subsurface layout, illustrated in Figure 1, contains 108 emplacement drifts, one Performance Confirmation(PC) observation drift, nine intake/exhaust shafts, and three access ramps. The existing Yucca Mountain facilities, shown in bold lines in Figure 1, include a 7.8 km long, 7.62 m (25 ft) diameter U shaped tunnel that is formed by the North and South Ramps at both ends of the Exploratory Studies Facility (ESF) drift and a 1.5 km long, 5.0 m (16.4 ft) diameter Enhanced Characterization of the Repository Block drift (ECRB) that were constructed from 1994 through 1998. These drifts were used for site characterization activities and have been incorporated into the subsurface repository configuration. The unexcavated perimeter access main and exhaust main drifts are typically 7.62 m (25 ft) diameter TBM excavations and the emplacement drifts are 5.5 m (18 ft) diameter TBM excavations. The turnouts leading into the emplacement drifts are to be excavated by either mechanical, or drill and blast methods and serve as the launch chambers for the emplacement drift TBM excavations.