Search Documents

By Peter Chou, Pooyan Asadollahi, Danny Lin

To maintain flexibility and ductility of tunnels crossing active faults, various mitigation measures are being utilized depending on fault offset movements and seismic design criteria. Examples of those approaches are simple bell and spigot joint, articulated joint, and complex deformable longitudinal bolt and spring joint system with seismic isolation washer. This paper presents a summary of tunnel fault crossing mitigation approaches and design considerations using previous relevant experiences in California as well as case histories from Japan, Taiwan, Turkey, Greece, and Italy found in literatures. Comparisons are made between large and small diameter tunnels, transportation, and utility tunnels, as well as bored, mined and cut-and-cover tunnels. Recent innovations, such as Japanese and Italian techniques, for tunnels crossing active faults are also discussed.

Jun 13, 2021

Invensys’ recently introduced Field Device Manager for Foxboro I/A Series distributed control systems provides the industry’s first solution that takes advantage of both the latest Enhanced Electronic Device Description Language (Enhanced EDDL) and FDT technologies. This combination provides comprehensive lifecycle support to configure, calibrate, commission, diagnose and optimize the performance of any vendors’ foundation fieldbus device. The I/A Series Field Device Manager enables users to take advantage of any EDDL, Enhanced EDDL and/or FDT host deliverables supplied by the device vendor.

Jan 1, 2007

By V. T. McLemore

The mining industry is at a crossroad. To sustain our technically based society, demands for commodities are increasing, and exploration for these commodities is a must. The debate is between sustainable development and the status quo and begins with exploration, where it is determined if a mineralized area contains enough potential ore to be mined economically. Mineral deposits are relatively rare and depend upon certain natural geologic conditions to form and may not always occur in locations that are most suitable to society. Exploration can be compatible with environmental protection and social responsibility, but difficult challenges face the industry to develop a property that is environmentally, economically, and socially responsible.

Jan 1, 2004

By John Reilly

The author?s paper at RETC 2007, ?Alternative Contracting Methods? addressed strengths and weaknesses of DBB+DB and introduced Construction Manager/General Contractor (Portland model) and Alliancing (Australian model). Considerable interest in these was expressed by several public agencies at that Conference and at the presentation. The author is assisting the Washington State Department of Transportation (WSDOT) and the Toronto Waterfront Revitalization Corporation (TWRC) with possible implementation of Alliancing. WSDOT is evaluating ways to do this and is considering a delivery methodology, under existing Legislation, based on the CMGC Portland model with incentives and disincentives, moving towards Alliancing. This paper will build on the 2007 paper and update implementation considerations.

Jan 1, 2008

By T. R. Kostecki, A. J. S. Spearing, A. Hyett, M. Gadde

Ground control research for underground coal mining has progressed significantly over the past several decades. With this progression, and the ability to analyze and model underground conditions, underground working conditions have significantly improved. In order to progress further, the behavior of roof support must be known and be adequately modeled, such that models can be used for support design under different geological and mining conditions. This paper discusses the results from a research project funded by the U.S. National Institute for Occupational Safety and Health (NIOSH) and undertaken by Southern Illinois University Carbondale and Peabody Energy. The research involved installation of active and passive instrumented bolts in mines, recording relevant in situ data and then attempting to model the behavior of the bolts as mining progressed. Such calibrated models could aid in design of roof supports under different geological and mining layouts and thus, hopefully, further improve rock related safety.

Jan 1, 2012

By R. Owen

The vision-based approach to process control involving fine particles in harsh on-line environments is discussed in this paper. The sensor equipment at the process location, consisting of a light source and a CCD camera provides RS-170 B&W video output. The video can be seen on a process monitor in the control room and is sent to a computer based Vision Processor. The Vision Processor contains a video digitizer and Canty developed software that extracts process information. The iron mine application controls thickener agent feed rate and thus settling pond overflow clarity. The sensor is mounted in the overflow flume of the outdoor settling pond and is used year around in the Minnesota weather. Alternate control system needs a low flow water sample which is subject to freezing in winter. The computer based vision processor provides 4-20 mA analog outputs for real time control as well as file archive for a history record.

Jan 1, 2001

By Sun Guangzhong, Liang Jinhuo

Adverse geological condition is a major factor which makes construction difficulty in tunneling. But if it is predicted and tunnel support is made efficiently in time, the above difficulty can be reduced. It is necessary to develop one or several effective and economical geological methods for prediction of tunnel geology while expensive and time-consuming instruments are used. This paper reviews and proposes several geological methods for prediction of fault, seam, contact zone, and groundwater inrush. These methods have been proved to be effective and economical in tunneling practice in China.

Jan 1, 1987

By S. D. Thompson

An AIME transaction by P.L. Allsman (1960), "Analysis of Explosive Action in Breaking Rock," contains many useful concepts applicable to blast design. Of special interest was the derivation of a heave blasting burden formula, which is important in establishing the maximum burden. Unfortunately, its derivation contains a fundamental error and then a compensating one. This formula was: [ ] The derivation used the impulse-momentum principle, with a 0.3 m thick (1 ft thick) radius of rock mass being acted on by an explosive impulse. However, the rock weight was not converted to mass by dividing by the gravitational constant. This mistake can be verified by checking the units in the formula, which resolve into m%-sec instead of meters. Adding the gravitational constant corrects this: [ ] If the minimum velocity is now taken as 0.3 m/sec (1 ft per sec), as was recommended, excessively large burdens result. Any appropriate rock velocity should be capable of throwing the rock mass a minimum distance so that the swell needed for breakage can occur. Unless the burden is extremely small and the bench height is very high, it is unlikely that a velocity of only 0.3 m/sec (1 ft per sec) will be sufficient. A review of the literature indicates that average rock velocities observed by camera studies typically range from 15 to 30 m/sec (50 to 100 ft per sec) (duPont deNemours and Co., 1977; Tansey, 1979). On this basis, a minimum rock velocity of about 15 m/sec (49 ft per sec) would be expected and not 0.3 m/sec (1 ft per sec). When a velocity of 15 m/sec (49 ft per sec) is inserted into the corrected formula, the results approximate those of the original formula with a velocity of 0.3 m/sec (1 ft per sec). The errors were approximately self-compensating [ ] References Allsman, P.L., 1960, "Analysis of Explosive Action in Breaking Rock," Transactions, AIME, Vol. 217, pp. 475-476. E. I. duPont deNemours and Co., 1977, Blasters' Handbook, 175th Anniversary Edition, Dupont, Wilmington, DE, pp. 233. Tansey, D.O., 1979, "The DuPont Sequential Blasting System," CIM Bulletin, Vol. 72, July, p. 80. Thompson, S.D., 1981, "Critical Review and Revision of Surface Blasting Practice," MS thesis, West Virginia University, pp. 308-316.

Jan 3, 1985

Thallium is an uncommon heavy metal that may be found in concentrations that exceed regulatory limits in mining influenced water associated with processing cadmium, copper, gold, lead, and zinc ores. This study evaluated cost-effective modifications to lime precipitation treatment to reduce thallium concentrations to below the EPA drinking water MCL of 2 ppb. The oxidative precipitation of Tl+ to Tlß+ by potassium permanganate was explored for thallium removal at low concentrations (1 ppm initial thallium). Laboratory batch tests were performed to evaluate the removal of thallium from synthetic solutions. Three ratios of potassium permanganate to oxidizable metals in solution were used (one-half, one and two times stoichiometry). Thallium was removed to less than 1 ppb for all stoichiometric ratios evaluated within 10 minutes of reaction. The efficacy of oxidative precipitation for thallium removal is presented.

Jan 1, 2011

By P. Mills

The four top barite-producing countries in the world are China, India, Morocco and the United States. China is currently the largest exporter of barite followed by India. More than 95 percent of the barite mined today is used by the petroleum industry as driller’s mud. The rest is used in the industrial market and the medical field. Most of the barite mined in the United States is in Nevada. This year, mining activity has increased due to an increase in oil exploration/development. This was caused by an increase in the crude oil prices.

Jan 1, 2005

By L. Mead

Dimension stone is a natural stone (granite, marble, limestone, sandstone and slate) that can be quarried, cut and shaped to conform to acceptable industry standards for size, consistency and durability. There are numerous outlets for the finished product in exterior and interior architectural and design applications. A continued growth market is with residential usage— particularly in new, upscale construction. This has become a competitive market between domestic producers and lower cost imported products. These imported products have become available at many of the building supply retail outlets and have increased the use of stone in residential construction and renovation. The traditional architectural application of dimension stone is tied to commercial and institutional building construction trends and market. There has been a noticeable increased usage of stone in the Sun Belt. This stone is usually supplied by local fabricating shops. It is used in the exterior and interior of shopping malls. This market generally uses local stone sources. It has increased the demand for sandstone, limestone and quartzite in this region of the country.

Jan 1, 2005

By C. R. Stephan

The Mine Safety and Health Administration's (MSHA) Ventilation Division continues to evaluate proposed explosion-resistant seal designs. There are currently eleven specific designs for explosion-resistant seals that are suitable for construction in underground coal mines. Seal construction in operating mines must be equivalent to those constructed in the Experimental Mine during the explosion testing program. Accidental failures of seals have occurred due to explosion pressures below 138 Kpa (20 psi). The possibility exists that the failed seals were not properly constructed. Also, conditions in the vicinity of the seals may change. Water may accumulate against the seals, heave or sag may cause detrimental effects on the seals, and sloughage of the ribs may negate hitching. If seals are not properly installed or maintained, they could fail when subjected to explosion pressures. If seals fail for any reason, the possibility exists for explosion propagation throughout large areas of the mine. There could be catastrophic consequences to an event of this nature. This report will present a limited discussion on the construction of each of these seals and will address related issues.

Jan 1, 2001

By K. Y. Haramy

Deep coal mines with strong roof and floor rock frequently encounter face and rib bursts. The burst problem is becoming more severe as mining depth increases, prompting efforts to relieve high stress areas ahead of mining. Successful stress relief reduces the occurrence of uncontrolled coal bursts. This report by the Bureau of Mines, U.S. Department of the Interior, presents a review of the most widely used methods to detect and destress high stress zones along coal faces. Stress-related burst problems and destressing efforts at a cooperating mine were investigated. Laboratory tests of the drilling yield method for high stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress at various confining pressures. A three- dimensional, multiple-seam computer modeling program, "MULSIM?, was used to evaluate the effectiveness of stress relief methods. Modeling results and guidelines for destressing are presented. Results indicate that dangerously high stress areas can be controlled by either proper planning or destressing. Proper mine planning guidelines and destressing methods such as volley firing, hydraulic fracturing, and auger drilling are discussed.

Jan 1, 1987

By S. Mukusha

Electronic spreadsheets are the most common and readily available software applications for analyzing and modeling quantitative problems. Spreadsheets can offer a vast array of opportunities for the analysis and modeling exercises encountered in the field of geomechanics. This study explores the potential for using spreadsheets of in the practice geomechanical engineering. The study also examines some of the barriers to widespread use of spreadsheets. Best practices and guidelines for overcoming potential pitfalls are discussed and highlighted through a case study.

Jan 1, 2000

By CORA ROELOFS

In the USA, miners are at higher risk for work-related disorders that could precipitate an opioid prescription, injury-related opioid prescriptions, and opioid overdose. We aimed to support prevention of these outcomes with an “opioid hazard awareness” miner safety training module. In January and February 2020, the training module was embedded within required mining safety and health training for stone, sand, and gravel miners in Massachusetts (USA). Training impact and reception were assessed with a pre- and post-training survey of trainee characteristics, training content knowledge, and attitudes. Over 800 miners were trained and over 600 responded to surveys. We found statistically significant improvements in opioid risk factor knowledge and knowledge of resources to help a coworker. Nonstigmatizing attitudes were high both at baseline and following the training. The training was perceived as relevant and useful by trainees. Improving opioid hazard awareness in high-risk worker populations has potential to reduce opioid dependence and downstream impacts including overdose death. Employer injury-prevention efforts should be reinforced while worker health and safety training enhances awareness of opioid-related harms and prevention strategies for miners and other high-risk worker populations.

Nov 19, 2021

By C. Frenzel, N. Blechschmidt

"INTRODUCTION There is no doubt about the time and effort companies put in establishing and maintaining their equipment. However, the question about how these companies can map the benefits comes up. Neither do they have the tools to quantify the benefit of their action, nor do they have the tools to know the actual quality of their current maintenance system. The resources used in the process seem futile to observers. It seems impossible to trace improvements and to get information about the impact of actions in retrospect. Improvements in maintenance performance cannot be recognised by management or shareholders. Thus the necessity for measuring the performance of maintenance systems is given. In this paper ConMoto is systematically showing the strengths and weaknesses of many companies' maintenance management and is providing field-tested proven design elements for measuring maintenance systems and implementing Value Oriented Maintenance. Considering only business assets in production facilities and related machinery out of all investment goods in Europe, you reach a value of around 9.7 trillion euros in 2008. In Germany alone the equipment replacement value amounted to about 1.9 trillion euros [8,10,11,13]. If you calculate a cross sector maintenance costs rate of 4.8 % (corresponding to the average value identified in this study), direct maintenance costs in European production locations add up to over 450 billion euros per year [3]. These figures speak for themselves. Yet maintenance is not only of enormous significance for European enterprises. Our experiences show that maintenance and asset management, particularly sustainability issues, are also increasingly moving to the forefront in the BRIC states, in the Middle East and in many emerging countries. First of all, in order to meet the resulting high quality and cost related requirements of maintenance systems, a comprehensive overview of the issue is needed. This overview is provided by a detailed analysis of 83 companies and production plants from various sectors – with amazing results. SIGNIFICANCE OF MAINTENANCE Current studies show the high financial significance of maintenance and asset management. According to the market study in the Asset Manager [9], in industrialised countries about 10 to 15 per cent of the labour force are employed in maintenance and facility management tasks. In Europe about 40 to50 million people are directly and indirectly involved in retaining the value of machinery, plants, buildings, transport systems and infrastructure facilities. A glance at the costs side also demonstrates the great relevance of maintenance. EU-wide annual direct maintenance costs amount to a total of more than 1,500 billion euros. In Germany alone they are about 250 billion euros. This impressive total is considerably exceeded by indirect maintenance costs caused by technical failures. Indirect costs are estimated to be five times higher (Figure 1). [7,12,14]"

Jan 1, 2018

By George A. Mealey

Caving mining methods that are based on a planned caving of rock above and/or at times surrounding the material being mined can be classified in three broad categories: longwall mining, sublevel caving, and block caving. Each of the three methods involves a distinct technology as well as art of operation. Each requires a relatively large, regular, and predictable ore body. As a rule, the effect of mining results in some form of impact or change on the surface. Operationally, underground caving methods are characterized by high productivity as well as a high percentage of extraction of the mineral being mined. A key element for the productivity of this form of mining is the ability to standardize the various elements of work taking place underground. Therefore, work-men may perform a specialized role rather than function as all-around miners. Further, the nature of the mining methods lend them to a high level of mechanization. Operations and manpower can be centralized into a relatively small area where supervision can be concentrated and therefore be more effective. Productivity as well as safety benefits thereby. The caving method is unique in that the exploitation openings are deliberately destroyed by the process of mining. Rock mechanics principles focus on the ensurance and the propagation of the cave as well as the continuance of the mine openings designed to extract the broken ore. As a rule, production operations are designed to maintain a steady, continuous flow of ore from the extraction areas. This steady flow rather than an intermittent flow tends to promote good caving action as well as reduce hangups.

Jan 1, 2008

By J. Drelich

The adsorption of oleate at the surface of titanium dioxide from aqueous solutions was examined by Fourier transform infrared (FT -IR.) spectroscopy using a germanium internal reflection element coated with a thin film of TiO2. This thin film, with a thickness of 100-200 A, was deposited on the surface of a germanium single crystal by RFIDC magnetron reactive sputtering. It was found that significant adsorption of oleate from a 0.02-0.03 mM aqueous solution on the surface of TiO2 thin film occurs at neutral pH, from about pH=5.5 to pH=7.7. Adsorption of oleate at the surface of the amorphous TiO2 thin film appeared to be reversible, involving soap-acid dimers.

Jan 1, 1997

By B. Cavender

Safety departments have traditionally been held responsible for the safety performance of their division or company. This approach leads to a lack of ownership of safety issues by the larger organization. An alternative paradigm is significantly more effective: the members of the work force (managers as well as workers) are fully responsible and accountable for safe production. The safety department is not extinct, however. Its role has changed, to focus on training, litigation, and external relationships such as community relations. This approach was implemented at BHP Copper's Superior mine and mill in Arizona. By obtaining the genuine commitment of the work force to accident-free production, the mill's MSHA incident rate immediately dropped from 7.4 to zero. The mill also ran one year with no MSHA citations. When this philosophy was implemented at the divisional level, the division's incident rate decreased from 9.5 to 1.1,an 88-percent reduction in six months.

Jan 1, 2000

The Virginia Center for Coal and Energy Research has been developing models of wireless signal propagation in underground coal mines since 2007. The current mine propagation modeling software, named COMMS, is able to locate potential broadcast points for underground wireless mesh systems and estimate their coverage. COMMS utilizes programmed routines to calculate necessary values to both quantitatively and qualitatively solve and analyze predicted coverage areas. The program approximates the spatial relationships that are encountered, such as ventilation regulators, belts and other obstructions. Using this model for propagation allows the optimal communications node locations to be calculated, by using lessons learned from current installations and experience with the new technology. In addition, the optimization can be calculated by checking all possible combinations of broadcast locations. This paper compares these optimization calculation methods. The ability to solve a mine?s communication network provides a pre-installation mine network design map, creates coverage maps of the mine and allows planning for future communication activities

Jan 1, 2011