Search Documents

By P. C. Thakur

Frictional ignitions (also called face ignitions) is defined as the rapid oxidation of a mixture of methane and air with a visible flame that could last from a few seconds to several minutes. These ignitions have a potential to turn into a mine explosion and eventually a large-scale mine fire. Over the last 22 years, U.S. coalmines have had 1566 frictional ignitions. There were no fatalities but serious injuries have occurred. Every effort, therefore, should be made to prevent frictional ignitions. The preventative measures fall under four categories: (a) degasification of coal seams prior to mining, (b) adequate ventilation, (c) wet cutting or water-jet assisted cutting and (d) machine design to minimize ignitions. The paper discusses each of these techniques in detail.

Jan 1, 2006

By S. Ragab

The objective of flotation models is to predict the recovery rate of minerals from a flotation cell. In this paper a CFD?based flotation models is presented. The model uses first order rate equation, and the collision frequency is estimated using Abrahamson [1] model with input from CFD two-phase simulations. Spatial distributions of dissipation rate and air volume fraction (also called void fraction) are determined by the two-phase hydrodynamic simulations. Knowing these parameters throughout the machine is essential in understanding the effectiveness of different components (rotor, stator or disperser, jets) on the flotation efficiency. Not only the average pulp recovery rate can be estimated but also the regions of high/low recovery rate can be identified. The CFD-based flotation model presented here can be used to determine the dependence of recovery rate constant at any locality within the pulp on particle diameter, particle specific gravity, contact angle, and surface tension.

Jan 1, 2012

By Yngve Jordal, Sverker Hartwig

The IVAR Project is Norway's largest sewer project presently under construction. One part of it is an 8.1 km (26 575 ft) long, 3.5 m (11 ft 6 in.) diam tunnel, bored in one year. The tunneling project has been running smoothly; however, not everything has been easy. A few of its features are highlighted in this paper: The use of 9 0 (12 cu yd) muck cars on a double track back-up in such a comparatively narrow tunnel. Employing only four men in the tunnel, including the loco driver. A quartzite dyke - 96% quartz with 350 MPa (50 000 psi) and more compressive strength - turned out to be 640 m (2 100 ft) thick instead of the predicted 90 m (300 ft). Passing under a gaseous swamp with only same 5 m (16 ft 5 in.) of rock cover on top.

Jan 1, 1991

By G. A. Gamble

Fans used to ventilate subway, passenger rail and vehicular tunnels are similar to the fans used to ventilate underground mines. However, tunnel ventilation fan systems are typically designed to meet NFPA 130 or 502 standards, while mine ventilation fan systems must comply with the appropriate federal mine safety regulations. As a result, fan operation requirements and performance criteria, as well as typical fan and duct configurations differ significantly for tunnel and mine ventilation applications. Variations in environmental conditions in tunnels as compared to mines also result in differences in fan performance and material specifications. The need to enclose tunnel fans within building structures creates space restrictions impacting fan size selection that are not commonly encountered in mine fan installations, resulting in different approaches to selecting fans for the two types of tunnels. This paper discusses the various similarities and differences in design considerations for tunnel and mine ventilation fans.

Jan 1, 2009

By T. R. Paquin

Powerful, easy to manipulate, ventilation modeling software is readily available to most mining engineers. Too often when preparing an initial ventilation model, engineers will go overboard in their design, creating a complex model with hundreds of branches. When, in practice, the creation of a less complicated ?to the point? model, containing a few well-constructed branches, would have delivered the same results. In this paper the author will demonstrate, by using actual feasibility report examples, that when designing a ventilation model, engineers should make more use of the K.I.S.S. (?Keep It Simple, Stupid?) Principle. As mining industry consultants we must continue to improve on, and deliver timely and cost-effective results to our customers.

Jan 1, 2009

By D. Dimitriadis, T. Polglase, W. Phillips, R. Jenny, M. Botz

Cyanidation processes for the extraction of gold or silver frequently involve the processing of sulfur-containing solids which react with cyanide to form thiocyanate. The formation of thiocyanate is an undesired side-reaction, and in many cases thiocyanate formation results in a prohibitively high cyanide consumption. With the increasing number of gold and silver mining projects which involve the processing of sulfide ores or concentrates or which utilize a biological sulfur oxidation process, more attention has been focused on minimizing thiocyanate formation and in treating solutions to eliminate toxicity associated with thiocyanate. Though not yet commercially applied, there are several technologies available to recover cyanide from thiocyanate to both reduce tailings toxicity and allow the reuse of cyanide otherwise lost to thiocyanate formation. This paper presents an overview of technologies available for recovering cyanide from thiocyanate along with estimated operating costs for the technologies. Pilot testing data suggests that in some cases, cyanide can be recovered from thiocyanate for approximately the same cost as newly purchased cyanide.

Jan 1, 2000

The molecular structures of isobutyl xanthate (IBX), diisobutyl dithiophosphate (DIBDTP), O-isobutyl-N-ethyl thionocarbamate (IBETC), O-isobutyl-N-ethylcarbonyl thionocarbamate (IBECTC) and O-isobutyl-N-ethylcarbonyl thiourea (IBECTU) were fully optimized using density functional theory (DFT) at the B3LYP/6-31+G(d,p) level with the integral equation formalism for the polarizable continuum model (IEF-PCM) in the aqueous phases. The effects of the polar groups in these thiol molecules on their collecting performances were determined by the energies and compositions of frontier molecular orbitals and the atomic charge values. Our results indicate that the sulfur atom(s) in IBX, DIBDTP, IBETC, IBECTC, or IBECTU molecule is the centre of reactivity. And the collecting abilities of these reagents for copper sulfide minerals follow the order as: IBX > IBECTU ? DIBDTP ? IBECTC > IBETC, and the order of their selectivities against pyrite is suggested as: IBX < DIBDTP < IBETC < IBECTU < IBECTC. The theoretical analysis provides an insight into the collecting powers of these collectors, and offers an atomic scale approach to understand the experimental data available in the literature. Keywords:xanthate; dithiophosphinate; thionocarbamate; thiourea; density functional theory; structure-activity relationship; copper sulfide mineral

Feb 27, 2013

By William R. Yernberg

The combined 79th Annual Minnesota Section of SME Meeting and 67th Annual University of Minnesota Mining Symposium was held April 11 and 12, 2006, in Duluth, MN. About 300 mining professionals attended, including engineers, executives, mining managers and suppliers, from throughout the United States and Canada. This year’s theme was “Success in the New World of Mining.” The SME Minnesota Section meeting included a keynote session, a special projects update, a general managers update and technical paper presentations. The University of Minnesota Mining Symposium program featured a panel discussion on Minnesota’s relationship with China. The combined meeting included a trade-show consisting of 64 booth spaces. Tradeshow demand exceeded expectations, and an additional 10 booth spaces were added in the registration lobby. Also included were an SME short course on pump basics and social events.

Jan 1, 2006

By A. M. Tonnos

Underground mining has yet to see an industry wide solution for control of their ventilation systems due to the complexity and sensitivity of the underground environment. Complexity arises from multi-level, multi-zone operations and sensitivity is associated with the impact that changes in equipment status and output have on air flows and quality throughout the mine. Our approach to solving this challenge incorporates system modeling and industrial control systems in a unified architecture. Although this approach can be applied to other processes and industries, this paper will cover the theoretical and practical aspects of an integrated model-control system (MCS) as it applies to underground mining ventilation.

Jan 1, 2009

By S. Addie

In the early 1990’s the British Columbia (Canada) mineral industry frequently discussed the need to participate in, and compromise with, public environmental interests in order to ascertain long-term stability. However, as the decade progressed the mineral industry withdrew from almost all meaningful public participation. As government protected areas policy in the past year has illuminated, there is a continued need for long-term land access stability. This paper historically analyses the public engagement policies of the British Columbian mineral industry while it participated in long-term consensus-based multi-stakeholder land-use planning processes. From this analysis the paper recommends that the mineral industry reengage the public and institute a new working relationship with environmental advocacy groups so as to ensure British Columbia becomes the most sustainable mineral producing jurisdiction in the world.

Jan 1, 2011

By R. Gensemer

A number of state and federal agencies are calling for development of aquatic life criteria for conductivity. These aquatic life criteria or ?benchmarks? are based on observed correlations between conductivity and benthic macroinvertebrate community composition, generally measured by composite metrics or indices. However, development of an aquatic life criterion for a composite variable like conductivity is made difficult by a number of factors. Based on a database from West Virginia, observed patterns of invertebrate community composition versus conductivity may instead be related to a combination of abiotic (e.g., ionic composition, habitat) and biotic (e.g., life history, colonization potential) factors. Many benthic invertebrate taxa also do not respond to increasing conductivity in a consistent relationship. Many states have determined that a composite variable, like conductivity or TDS, is not appropriate for criteria development, as many studies have shown that toxicity varies as a function of ion composition and can be mitigated by elevated hardness. We conclude that the relationships between conductivity and changes in benthic macroinvertebrate community composition are neither strong nor reliable enough to warrant derivation of a criterion based solely on conductivity.

Jan 1, 2011

The 23rd annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held at the Tucson Marriott University Park Hotel, Tucson, AZ on Saturday, Dec. 3, 2005. The Mining Foundation of the Southwest is a non-profit organization. It educates the public about the mineral industries and reports outstanding accomplishments in the fields of mining and the earth sciences. This year’s inductee, guest of honor and featured speaker at the banquet will be Pierre Lassonde, president of Newmont Mining and resident of the World Gold Council. He is one of Canada’s leading gold analysts.

Jan 1, 2005

By J. Barrett

State-of-the-art wireless communication and location-tracking technologies will dramatically change the face of mine worker safety. The MineTracer System developed by a Liberty Lake Washington company is a broad capability wireless sensor network based on a new breed of technologies known as wireless mesh systems. In this paper, R&D Manager Jim Barrett summarizes the balance of engineering tradeoffs that result in a system that (1) performs well, (2) is survivable against many types of mine accidents, (3) operates for many hours post-accident on battery power, (4) meets stringent MSHA requirements for intrinsic safety, and (5) is economically affordable for the mines.

Jan 1, 2009

Fully mechanized longwall mining with large mining heights (LMHs) in shallow-depth thick coal seams has been widely applied in Shenfu coalfield, China. Dynamic loading and rib spalling is serious when the LMH working face experiences periodic weighting in shallow coal seams. The advanced breaking position (fracturing ahead of the face) in the roof affects the strength of the mine pressure (weighting) when the roof is broken. Based on the theory of the “elastic foundation beam,” this paper presents a mechanical model for the advanced breaking of the roof, including a predictive formula. In an attempt to verify the formula, a field program consisting of multiple-point borehole extensometers installed in the roof in advance of the longwall face was performed in the No. 22201 working face of Zhangjiamao coal mine in the Shenfu mining area, China. The field measurement results show that the roof movement of the LMH working face is detected prior to roof pressure increase, and that the roof breaks approximately 5–8 m ahead of the face. This compares with a calculated value of 6.9 m, indicating that the formula developed in this research is reliable and should have application in predicting roof pressure associated with LMH working faces in shallow coal seams.

Jul 28, 2020

By Don F. Macfarlane

This paper describes the field application of the NTH fracture classification to rock encountered in the construction of the 9.6 km long, 10m diameter, Second Manapouri Tailrace Tunnel. Excavation of the tunnel was undertaken by TBM between 1997 and 2002, in gneisses, granitic and diorite rocks. The paper outlines an adaptation of the NTH fracture classification used during the geological logging of this tunnel. The NTH fracture classification was primarily applied to assess discontinuity spacing for tunnel support requirement decision-making. The paper includes some general comparison of NTH classes with overall penetration rate.

Jan 1, 2008

By D. L. Stevens

Following an in-depth scenario and strategic planning exercise in 1997, Noranda’s mine production goal was set at 500,000tonnes per year of both copper and zinc metal within five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in our program but here is what we did first: - Combined the exploration and business development groups - Formed teams to search for and respond to opportunity - Made our geologists more business minded and our engineers more optimistic - Went global - Set clear thresholds, farmed out the marginal properties, fast tracked the others - Focussed reconnaissance exploration where we had a clear competitive advantage - Became a “flexible” partner to both juniors and seniors

Jan 1, 1999

By P. C. Thakur

In Part I of this paper, it was established that the width of longwall faces in highly gassy mines is primarily limited by the volume of air reaching the tail-end of the face. The ventilation air reaching the tail-end of the face should be not only enough to keep methane concentrations below the statutory limits (generally 1 percent) but also enough to prevent any gas layering. The air volume leaking from the longwall face into the gob should also be able to push the explosive methane-air mixture away from the gob area immediately behind the longwall face where active roof-fall is taking place (typically 30-45 m). The second group of variables that also controls the width of the longwall panel consists of (a) the rate of advance, (b) bleeder air quantities, (c) specific methane emissions for the gob area and, (d) efficiency and cost of gob gas capture. This paper will discuss the second group of variables and its impact on the optimum width of longwall faces in highly gassy coal mines.

Jan 1, 2009

By J. de Bakker

It hardly needs to be repeated that if coal is to continue as America’s premier source of cheap energy, it is absolutely necessary that the carbon dioxide from its combustion somehow be sequestered. A promising method proposed to accomplish this is the “indirect” carbonation of serpentine in a concentrated magnesium chloride brine. Indirect carbonation could be also applied to precipitate magnesium in lateritic nickel processing: this would not only solve magnesium-control problems in laterite hydrometallurgy, but also reduce its energy requirements and create CO2-sequestration credits. Fifty-five percent of the electricity generated in the United States comes from coal-fired power plants, and American coal reserves can last over 500 years at 1990-level consumption1. Coal is therefore both abundant and cheap: it could (and in fact probably will) continue to be an affordable source of energy, both for producing electricity and as a feedstock for liquid hydrocarbon production by Fischer-Tropsch reactions. As a result, it is important to find a workable method of permanently sequestering CO2.

Jan 1, 2007

Six pioneers of the American mining industry will be inducted into the National Mining Hall of Fame on Saturday, Sept. 13, at the Museum Convention Center in Leadville, CO. The 16th annual Mining Hall of Fame induction banquet will begin with a reception and open house at 5:30p.m., followed by the dinner and program at 7 p.m. The six inductees include James M. Gerstley, the only living member, and George O. Argall, Jr.; John F. “Leadville Johnny” Campion; Charles R. Nailler; Edwin N. Pennebaker and Russell L. Wood.

Jan 1, 2003

By Daniel Saint Don, Jacques Dumouchel

QIT Madagascar Minerals (QMM)’s heavy mineral sand deposit located near the Village of Fort Dauphin, Madagascar was recently drilled using Boart Longyear Company’s Mini-Sonic drill. Continuous sand core samples were obtained to a depth of up to 30 meters for analysis and compared with the existing drilling data. Results were used as part of a validation process of the resource estimate, based on approximately 1,500 exploration holes drilled to date.

Jan 1, 2005