Search Documents

By D. Nardini

The need to move towards faster and safer mine development is a key priority in mining houses globally. In addition to this, South Africa faces an array of challenges introduced by labour-intensive operations; hence a study was conducted to look into improving development rates and labour productivity, specifically in the areas where trackbound flat-end development is required. The aim of the study was to propose a method to deliver fit-for-purpose tracked tunnels that advanced at a rate of one blast per end every single working day. A major part of the study was to optimize the selection of an appropriate trackless fleet and mitigate any constraints introduced with the mechanization. This was done by creating scenarios, based on a typical case study, looking into the aspects around safety, mine design, mine activity cycling, men and machine requirements, service installations, and trackless-trackbound interfaces. The case study was based on a deep-level gold mine developing twin headings with connectings; however, with the move to extend and deepen platinum operations it is foreseen that twin end development will become more prevalent due to ventilation, logistical, and other requirements. With the introduction of the trackless mechanized system suggested, development rates of 56 m of system advance are expected (189 m total development), with on an average of three headings and fixed blast times. Scenarios run with multi-blast conditions yield expectations of 75 m/month advance of the system, significantly higher than the conventional performance seen today.

Jan 1, 2012

By I. Silin, H. Wotruba, A. Liono, I. Volobayev, Y. Rubinstein, D. Gürsel

Old, abandoned or in situ processed and storaged tailings can be a potential source of remained valuable metals and minerals. By reprocessing of tailings, it is possible not only to achieve economical profit from recovery of valuable metals, but also to reduce environmental damage caused by tailings such as generation of acid mine drainage from sulfide minerals, mobilization of heavy metals, soils and groundwater contamination. In addition, storage facilities can be successfully redesigned with modern geotechnical requirements and monitoring to avoid a dam collapse of abandoned tailings. In this case study, the processing of low grade abandoned tailings was investigated. Copper (0.15%), cobalt (0.032%) and gold (0.35 ppm) were determined as main valuable and recoverable metals. Cobalt occurs as cobaltite and cobaltiferrous pyrite, while chalcopyrite represents copper. The fine fraction of tailings below 32 μm is enriched with cobalt and copper. Preliminary test-works with initial tailings sample were aimed to recover copper, cobalt and gold. The previously tested magnetic and gravity separation could not recover the metals in a pre-concentration step. Flotation tests of the tailings sample had shown a suitability for flotation without previous regrinding of the tailings. The valuable minerals are first proposed to be recovered by collective flotation, followed by a selective circuit with production of a low grade copper concentrate and a cobalt bearing pyrite concentrate. Based on various tested collectors, amounts of sulfidisation agents and activators, a suitable reagents regime was determined and used for up-scaling by locked cycled test. Keywords: reprocessing, tailings, copper, cobalt, gold, flotation, cobaltite, cobaltiferrous pyrite

Jan 1, 2020

By T. Nesane, S. S. Mnyakeni-Moleele, L. C. Murulana

The effectiveness of two synthesized ionic liquids, 1-(benzyloxy)-1-oxopropan-2-aminium 4-methylbenzenesulfonate (1-BOPAMS) and 4-(benzyloxy)-4-oxobutan-1-aminium 4-methylbenzenesulfonate (4-BOBAMS), were evaluated for mild steel corrosion inhibition in 1.0 M hydro-chloric acid solution, using electrochemical impedance spectroscopy (EIS), potentiodynamic polarization (PDP), and gravimetric techniques. Organic moieties responsible for the adsorption process on mild steel surface were investigated using Fourier transform infrared spectroscopy (FTIR). Gravimetric analysis revealed that the inhibition efficiency of 1-BOPAMS and 4-BOBAMS increased with concentration, with maximum inhibition values of 90.32% and 97.91%, respectively, at the highest concentration of the inhibitors. Gibbs free energy (ΔG°ads) values indicated a strong interaction between the mild steel surface and the molecules of the ionic liquids, and that the adsorption process was spontaneous. These values also show that the inhibitive nature of ionic liquids against mild steel corrosion is caused by a mixedtype of adsorption film formed on the steel surface. The Langmuir adsorption isotherm was used to describe the adsorption of ionic liquid molecules onto the mild steel surface. Polarization curves showed that 1-BOPAMS and 4-BOBAMS have a similar effect on both the anodic and cathodic half-reactions, indicating that they prevent the dissolution of mild steel through both physical and chemical process. Nyquist plots were defined by incomplete semicircle capacitive loops, showing that the charge transfer mechanism controls the corrosion of mild steel in acidic solution.

Apr 1, 2021

By X. Zhang, Z. T. Yuan, C. Zhang, H. M. Zheng, X. M. Wang, L. X. Li, N. Li

In metal mines, comminution is commonly used to liberate minerals for subsequent mineral concentration processes, such as flotation, magnetic separation and gravity separation. However, ores are aggregates of valuable minerals and their disseminated gangue minerals, and these minerals exhibit diverse comminution behaviours. In carbonate-bearing iron ores, hematite, siderite, and quartz are the predominant minerals, of which hematite is the objective recoverable mineral. In this regard, the present study aimed to identify the imperfections in siderite minerals by X-ray computed tomography (XCT), and thus quantitatively characterise their size and shape in terms of Feret diameter and aspect ratio, as well as other parameters. XCT images indicated the protogenetic ubiquity of pores <5 μm in diameter and cracks of 7-8 μm inside siderite particles. In the ground product of artificially mixed siderite and hematite, siderite particles were smaller than hematite particles. Siderite particles had a larger surface area and greater surface roughness than hematite particles of the same volume, which was attributable to the intrinsic holes and cracks in siderite particles. This study provides an insight into the relationship between the inherent imperfections of minerals and their comminution properties. Keywords: Siderite; X-ray computed tomography; particle imperfections; grinding behaviour; sliming

Jan 1, 2020

By H. Zhong, S. Wang, Q. Sun

The flotation performance of 2-(benzylthio)-acetohydroxamic acid (BTHA) to diaspore was first evaluated by micro-flotation tests. The adsorption mechanism was further investigated through adsorption experiments, molecular dynamics simulation, zeta potential and X-ray photoelectron spectroscopy (XPS). The results demonstrated that BTHA had a stronger ability to collect diaspore in comparison with another diaspore collector, benzohydroxamic acid (BHA), especially under the condition of weak alkalinity, the flotation recovery can reach 90%. The more negative interaction energy (ΔE) between BTHA and diaspore from molecular dynamics simulation results revealed that BTHA had an easier adsorption ablity onto diaspore than BHA, which matched with adsorption results. The zeta potential and XPS revealed that Al atoms might bond with -C(=O)NHOH by formation of Al-O bonds. Keywords: Diaspore, flotation; adsorption; 2-(benzylthio)-acetohydroxamic acid

Jan 1, 2020

By M. S. Shishvan, S. Klerkx, J. Sattarvand

The inaccurately drilled blastholes from the planned locations cause changes in the spatial distribution of explosive energy; some areas of the blast may receive a surplus of explosive energy, while others see a reduction. This results in less uniform fragmentation, reduces the efficiency of mining operations and increases costs. Additionally, it can lead to slope stability issues, flyrock, and uneven benches. To mitigate these problems, this study attempts to reduce differences in the explosive energy distribution (EED) through an optimization approach that adjusts the height of explosive columns in blastholes. Two optimization algorithms, the Genetic Algorithm (GA) and Tabu Search (TS), are tested. The latter is preferred for its local search neighbourhood strategy that gives superior computation times. Applications on different blast patterns result in improvements of 0.53–1.54%, or 2.14–3.94% when only the affected blocks are considered.

Sep 1, 2021

By H. Mulder, M. C. Bekker

The principal objective of this investigation was to conduct a thorough literature review on the status of project readiness mechanisms, tools, techniques, and frameworks for mining projects. The review aimed at identifying common readiness evaluation criteria as well as potential shortcomings that prevent the establishment of a generalizable project readiness index. The literature review included a general overview of capital project performances and the importance of project readiness assessments to improve project delivery success. The study then progressed towards literature involving mining projects and how this differs from infrastructure and industrial project assessments. The paper concludes by summarizing the current state of mining project readiness assessments, the unique and differentiating factors to be considered, and suggests recommendations towards the development of generalizable readiness assessment criteria for mining projects.

Sep 1, 2022

By M. Wrobel, J. Hammerschmidt, M. Runkel

Fluid-bed technology is a key pyrometallurgical step for processing a vast number of ores and concentrates. Over the past 50 years, considerable research and development efforts have been made by Metso Outotec to expand the application window of this technology. This paper illustrates different processing routes where fluid-bed technology plays an important role in the production of the copper. The fluid-bed processes utilized are partial, sulfate-producing, and dead roasting. The focus of this paper considers the advantages of the dead-roasting process. This “zero waste” process can provide copper oxides, steam, electrical power, and sulfuric acid for new and existing solvent extraction–electrowinning plants. In a case where an operation is running out of oxidic ores and concentrates, fluid-bed roasting can be applied to close this gap and provide the required copper oxides in a sustainable way.

Jan 1, 2023

By D. N. Golenkov, N. I. Lomaka, A. V. Kozub, T. V. Ignatova, E. V. Shelepov, D. O. Sharkovskiy, A. V. Chanturiya, R. I. Ismagilov

The modern Russian iron ore mining industry is faced with multiple challenges from everincreasing requirements of steel-making, the value of iron ore concentrates, depletion of high-grade ore reserves and complications of the mining and geologic environment’s necessity to process low-grade ores with complex material composition and low valuable mineral content; with finely disseminated aggregates of metal and non-metal minerals responding similarly to processing. The upgrade of the existing operations’ fine wet screening was implemented by Metalloinvest; as well as the design of a process flowsheet for concentration oxide ferruginous quartzites with low concentrating ability. The scientific basis for improvement of low grade ore concentrating efficiency and the upgrade of market product quality is supported by an in-depth study of ore characteristics, application of high performance equipment for separation of fine-grained mineral aggregates and use of depressor selective to ferruginous minerals in the flotation process. The benefits of wet fine screening have been proven by industrial scale tests; as well as the feasibility of significant upgrades in product quality which have been confirmed as a result of the tests. A road-map for the upgrade of an existing process for the concentration of unoxidised ferruginous quartzites deposited in the Mikhailovskoye ore field was developed, based on the industrial scale test of a fine screening process. With reference to the ability for concentration, three major ore types oxidised ferruginous quartzites were defined as a result of comprehensive geological mapping and process sampling: oxidised ferruginous quartzites with good concentrating ability: over Fe67% grade of concentrate with ca. 80% iron recovery; oxidised ferruginous quartzites with moderate concentrating ability: Fe65-67% grade of concentrate with 70-72% iron recovery oxidised ferruginous quartzites with low concentrating ability: below Fe60% grade of concentrate (cannot be processed into desired grade market product). A process flow diagram combining magnetic separation and flotation has been designed and recommended for implementation based on the in-depth research of defined Mikhailovskoye deposit iron oxide types, including grain size, chemistry, petrographic, mineralogy, hematite and magnetite grain size distribution and liberation analysis.

Jan 1, 2020

By S. Chatterjee, F. Suparno, A. Paithankar

Estimating reserves and quantifying resources stand as pivotal and intricate endeavours within the realm of coal mining operations. Intricate geological formations compound the challenges in resource estimation, thereby complicating reserve calculations. The uncertainties tied to geological attributes of coal, encompassing parameters like tonnage and coal quality, wield significant sway over resource and reserve computations within coal mines. This research delves into the domain of geological uncertainties, with a specific focus on calorific value, aiming to numerically characterise resources and reserves within an open-pit coal mine situated in Indonesia. To quantify resources, the coal seam geometry underwent simulation via a multipoint geostatistical technique known as single normal equation simulation. A geologically established coal seam served as the training image for generating 20 equiprobable coal models. To simulate CV, 50 realisations were generated for each simulated coal seam, utilising sequential Gaussian simulation. Deviations of the simulated coal seams ranged from -0.07% to 5.48% in comparison to the training image. The CV simulation yielded an average value of 5,920.29 kcal/kg, accompanied by a standard deviation of 586.54 kcal/kg. However, the average CV spanned from 5,305.26 kcal/kg to 6,526.55 kcal/kg across diverse simulations. For reserve calculation within the context of geological uncertainties, an algorithm rooted in maximum flow graph theory was employed to construct the ultimate pit for the coal mine. Within this final pit, the average stripping ratio was 1.62, coupled with a CV value of 6,019.66 kcal/kg. When juxtaposed with the deterministic model, the findings underscore that the stochastic ultimate pit delineates a more expansive excavation, accompanied by a heightened undiscounted cash flow.

Oct 2, 2025

By L. A. Cornish

Pt-based alloys for high-temperature applications in aggressive environments have been under development for over 10 years, and are targeted to be used as either as bulk, or as coatings. The alloys comprise Pt, Al, Cr, and Ru, and the microstructure has been improved by composition to a best possible analogue of the nickel-based superalloys, which these alloys could partially replace. This was necessary because the previous best alloy had a strengthening precipitate volume proportion of only approximately 40 vol.%, whereas the nickel-based superalloys have around 70 per cent, and a lower volume would mean that the strength would not be the best that could be obtained. The microstructures were assessed using electron microscopy, and have been related to the alloys? hardness values. The current microstructures are much more like those of NBSAs, with a high proportion of the strengthening ~Pt3Al precipitates. Since the samples have to be small (platinum is expensive), hardness has been used as an indication of strength. Nano-indentation studies showed that the hardness and Young?s modulus were higher for ~Pt3Al than the (Pt) matrix. More extensive oxidation studies have been undertaken on the previous optimum sample, and the effect of cooling rate after heat treatment has also been ascertained. In addition, the samples were studied after different heat treatment times, and cross-sections were made in order to characterize the alumina scale that formed. The oxide scales of Pt-11Al-3Cr-2Ru (at.%) up to 100 h exposure did not spall, and were at least as good as those of the ternary alloys. There was no discernable Al depletion zone in the substrate, although it could have been at a greater depth than thickness of the samples studied. Further additions to the Pt-Al-Cr-Ru alloys have been studied, to increase the melting temperature as well as to reduce the platinum content without compromising the properties. Reduced platinum content would have the benefits of reduced density and cost. The target elements include vanadium and niobium, of which vanadium is of special interest, since it is a South African product. Before these additions could be made, phase equilibria studies were undertaken so that the maximum addition could be ascertained, and also to check any possible ternary phases, which could be deleterious. Work on the Pt-Al-V system revealed a ternary phase, ~V27Pt54Al19 (at.%), which has a eutectic reaction with (Pt). The maximum V addition is likely to be around 15 at.%, otherwise ~Pt3V or the ternary phase will form, and not the required (Pt)/~Pt3Al phases.

Jan 1, 2012

By A. Melkumyan, K. Silversides

Chemical assays collected from blast holes have the potential to greatly improve the local accuracy of grade models. Assays must be assigned to the correct domain or they will introduce errors. Boundary surfaces created from the widely spaced exploration holes (~50m) do not provide sufficient resolution to correctly delineate domain boundaries between closely spaced (3-5m) blast holes. This paper demonstrates a probabilistic method for classifying production blast holes near domain boundaries. Gaussian processes models are applied to identify the assays and assay ratios most suited to distinguishing particular domains. These models are combined with the exploration based surfaces to classify the blast holes that can be confidently assigned to a particular domain. A reiterative method is used, where information from the blast holes closest to the exploration holes is used to label blast holes further away. This is tested on two domain boundaries in a banded iron formation-hosted iron ore mine.

Sep 1, 2021

By L. M. Tavares, H. A. Petit, P. P. Cavalcanti

Iron ore pellets experience degradation during handling due low energy impacts and stresses. These impacts lead to volume or surface breakage of the pellets, creating fine particles that accumulate along the process. Some of the particles are in contact with the air and are dragged as dust into the workplace or into the atmosphere. The aerodynamic size of the particles allows them to be potentially inhaled by the workers or to be carried to nearby communities. Dust emission becomes critical at specific locations, such as transfer chutes and stockpiles. This work models the dust generation that occurs in an iron ore pellet stockyard using a methodology that combines experiments to quantify the degradation of the pellets to mathematical modelling of the dust emission mechanisms in the stockyard. First, laboratory tests were used to characterise the amount of mass and the particle size distribution of the dust generated by degradation under controlled conditions. Second, the flow over a stockpile of an iron ore pellet company was simulated with the aid of computational fluid dynamics (CFD) simulations. Third, semiempirical equations linked the data generated by simulations and laboratory tests to estimate the dust emission in the stockyard. Finally, results were validated with measured field data, obtained with a novel online measurement tool. Results suggest that the approach is able to predict dust emission with sufficient accuracy and can be used for further implementation in the management of operations and decision making in order to reduce the environmental impact of the process. Keywords: Iron ore pellets, abrasion, dust emission, mathematical modelling

Jan 1, 2020

By R. D. Alorro, B. Tadesse, E. Aghaei

Cinnabar (HgS) and native mercury (Hg) are the most common naturally occurring forms of mercury found in most gold ores subsequently released into the environment during processing. Mercury and its compounds are extremely toxic and recognised as serious health and environmental hazards. This research investigates the possibility of mercury (Hg) removal from waste solutions from gold processing using iron-aluminium (Fe-Al) bimetallic particles. The synthesis of Fe-Al bimetallic particles using zero-valent aluminium and ferric chloride as precursors were performed following the optimisation of influencing factors. The presence of both metals in the prepared bimetals was confirmed by XRD analysis. The experiments for mercury removal by bimetals were designed using the central composite design and Minitab software based on two variables including contact time and adsorbent dosage. The best result of Hg(II) removal (>90%) was achieved using 4 g/L bimetals and contact time of 75 min. However, the statistical analysis of results indicated that these parameters have only a minor contribution to the removal of Hg(II) by Fe-Al bimetals. Higher bimetal dosage and contact time resulted in a higher Fe dissolution from the Al surface which can be attributed to the presence of nitrate (# $) ions in the solution. However, adding 0.1 M NaCl to the Hg solution had a positive impact on Hg removal by improving the conductivity and electron transfer within the solution. The Fe-Al bimetallic particles are promising substances for further testing of Hg removal from gold processing waste solutions with different conditions and constituents. Keywords: Mercury removal, gold processing, Fe-Al bimetals, optimisation

Jan 1, 2020

By T. Szendrei and S. Tose

Historical approaches to the problem of flyrock based on correlation studies and regression analysis, including artificial neural networks and similar techniques, are inherently incapable of addressing two core issues – root causes of flyrock and projection velocity. A further shortcoming of correlation techniques is that they give no information on the influence of rock size and shape on the flight distance. The scaled depth of burial model for crater blasting in the collar zone and bench face does not specifically address the question of flyrock velocity. A third approach, based on flight trajectory calculations, often neglects the very significant effects of air resistance on the trajectory. Some trajectory models incorporate air resistance but use an implausible fragment velocity model that cannot propel sizeable rocks to distances much beyond 150 m. Nonetheless, trajectory calculation incorporating the effects of air drag affords the most promising approach to the prediction of flyrock range. A unique and insightful feature of the proposed realistic flight modelling is that it collapses all suspected causes of flyrock, many of which are not well understood, to just a single parameter – the launch velocity. This indicates that the root causes of flyrock lie in the mechanisms of momentum transfer to broken rock and suggests new avenues of study.

Dec 13, 2022

By G. Akdogan, J. H. Zietsman, C. Dorfling, D. Attah-Kyei

The development of newer and improved electrical products has led to an increase in the rate at which older products are discarded as waste. The main focus of electronic waste is the printed circuit board (PCB) because of the inherently high value of contained metals such as gold and copper. Several options for treatment of the non-metallic fraction including material recycling, where the residue may be used as inclusions in concrete or asphalt materials with minimal processing or chemical recycling, where chemicals and fuels are produced from the residue using pyrolysis exist. In this paper, the utilisation of the non-metallic leached PCB waste fraction as reductant in secondary copper smelting was investigated. Analysis of the leached residue revealed that PCB is highly amorphous and has a carbon content of 28.5%, an oxygen content of 23.1%, with the ash and volatile matter contents 40.1% and 44.8% respectively. Thermodynamic simulations of secondary smelting of copper were conducted in terms of metal recovery, and the energy required when PCB was used as a reductant. The results were also compared with that of coal and PCB-coal blends. The simulations revealed that as PCB in the blend used as reductants increases, the amount of energy required for the smelting operation decreases. Metal recovery slightly decreased as the mass percent of PCB in the blend increased due to lower carbon content present in PCB relative to coal. The results also highlighted the energy saving with PCB-coal blends which was around 160 kWh per ton of feed relative to coal. The decrease in the amount of energy required for the operation is attributed to the higher volatile content of the PCB, which is also a part of the reduction process. Keywords: PCB leach residue, alternative reducing agent, secondary copper smelting

Jan 1, 2020

By P. J. Petit

Changing mining conditions, legislative issues, rising costs, and the constrained supply of skills and electricity in South Africa, have been some of the criteria forcing mine operators and engineers to review the traditional use of compressed air to power underground hand-held drilling operations in narrow-stope, hard-rock mines. In answering the question, &apos;What is the best way to power this mine?&apos;, they have resorted to trade-off studies with results of limited usefulness, because they are site-specific, and use only a few comparative parameters, based on a small data set. This paper aims to provide definitive, objective and quantitative decision-making approaches to evaluate alternative energy delivery systems for stoping in narrow-reef hard rock mines, based on primary and relevant criteria. These include quantifiable criteria such as capital expenditure, operating costs, resulting financial returns, energy and water usage, production performance, life-of-mine, etc. Other important criteria with qualitative aspects are integrated. These are safety, health and environmental concerns, legislative requirements, business risk, technology change, etc. The paper begins with a review of decision making processes available, and proposes the use of the analytical hierarchy process (AHP) method as a multiple-criteria decision making tool and the decision tree-based on milestone-driven uncertainties, to validate the selection of the energy delivery system. The results of a multiple-criteria questionnaire completed by a variety of industry experts and professionals, such as production and operation managers, consultants, suppliers and techno-financial analysts, are discussed. The evaluation indicates the potential for hydropower to be the best solution for narrow reef hard rock mines, based on current information, mine design layout and production.

Jan 1, 2012

By S. Subramanian, L. Mweene

A siliceous low-grade copper ore from Mpanda Mineral Field (MMF), located in south west Tanzania consisting of SiO2 (58.3%), Fe (10.4 %) and Cu (0.9 %) was initially subjected to selective dispersion-flocculation using sodium trisilicate (STS) as a dispersant and xanthan gum (XG) as a flocculant. Subsequently, the selectively flocculated fraction was floated using a collector combination of potassium ethyl and amyl xanthate (1:1) in the presence of poly-ethylene oxide (PEO) as a silica depressant, to get a copper concentrate. The mineralogical investigations confirmed that the MMF ore was mainly composed of quartz, chalcopyrite and pyrite. Adsorption studies indicated that the adsorption density of XG on MMF ore decreased with an increase in pH, while that of PEO was independent of pH. The adsorption isotherms of XG and PEO on MMF ore exhibited Langmuirian behaviour. The zeta potential studies of MMF ore indicated that the iso-electric point (IEP) was located at pH 2.6, presumably due to its high silica content. In the combined presence of XG and STS, the zeta potential of MMF ore became more negative, with an increase in the concentration of STS. However, in the presence of PEO, the zeta potential of MMF ore became less negative with an increase in the concentration of PEO beyond the IEP, without shifting the IEP. Selective dispersion-flocculation of MMF ore improved the flocculated chalcopyrite grade to 19.8 %, yielding a degree of flocculation and a maximum separation efficiency of 12.1 % and 85.7 % respectively, after three desliming stages in the presence of 30 ppm of STS and 30 ppm of XG. A copper concentrate of 29 % grade and 90 % recovery containing silica of 0.9 % grade and 1.7 % recovery was achieved by flotation of the selectively flocculated component, using PEO as a depressant for quartz. Keywords: Flotation kinetics, flotation machines, flotation bubbles, particle size

Jan 1, 2020

By A. Sampson-Forsythe, P. Morissette, A. R. Punkkinen, D. R. Chinnasane

"The performance of ground support systems under dynamic loading is typically assessed in a qualitative and subjective manner. As a result, it is difficult to develop an explicit knowledge on the mechanisms of action and interaction of support elements subjected to rockbursts. This paper examines rockbursts that have occurred at Creighton, Copper Cliff, and Coleman mines since 2000, 2004, and 2006, respectively. The mines are located in the Sudbury Basin, in Ontario, Canada. The majority of pertinent information was obtained through on-site field assessments, seismic system records, and numerical elastic stress modelling. Passive monitoring is used to link the evolution of the frequency and severity of rockbursts to the evolution of mining and support practice at the three mine sites. Based on the collected data, ground support elements that enhanced the capacity of support systems to withstand dynamic loads are identified. IntroductionThe selection of appropriate mining methods, extraction sequences, rock mass de-stressing techniques, and ground support systems is of great importance in mitigating the level of rockburst-related risk. In burst-prone conditions, the design of support systems should account for the anticipated dynamic load demand and the capacity of the available support options. Furthermore, an economical design should, implicitly or explicitly, take into consideration the consequences of a rockburst and its impact on worker safety and mine productivity. Stacey (2012) has argued that we have a limited understanding of the mechanisms of rock mass behaviour in seismic conditions. This is compounded by a ‘lack of understanding of the mechanisms of action and interaction of support elements under dynamic loads’ (Stacey, 2012). Consequently, the design of support systems required to manage dynamic loads is usually based on experience. The assessment of the dynamic performance of ground support systems is typically subjected to qualitative (and sometimes subjective) interpretations from ground control personnel."

Jan 1, 2017

By D.W. Gentry

1. Book reviews Mine investment analysis, by D.W. Gentry and T.J. O&apos;Neil. Society of Mining Engineers (Caler No. D, Litleton, CO 80127, U.S.A.). US$50.Finance for the mineral industry, by C.R. Tinsley, M.E. Emerson, and W.D. Eppler. Society of Mining Engineers (Caler No. D, Litleton, CO 80127, U.S.A.). US$50. 2. Mintek reports The folowing reports are available from the Council for Mineral Technology, Private Bag X3015, Randburg, 2125 South Africa. They are free of charge to South African addressees, but there is a handling charge of US$25 per copy for reports sent to overseas destinations. Report M291D Removal of pebbles and pre-crushing of selected feed material in autogenous milling, by D.I. Hoyer. First issued Nov. 1986, reissued Apr. 1988. 16 pp Report M350 A survey of miling and mil-lining practice on South African gold mines, by M.S. Powel. Jun. 1988. 30 pp Report M356 The distribution of cobalt in mineral constituents of the Merensky Reef and UG-2 Chromitite Layer of the Bushveld Complex, by G. Smits. Jut. 1988. 13 pp Report M359 The development of a mobile laboratory for the monitoring of gold and cyanide in alkaline cyanide solutions, by R.V.D. Robert, C. Pohlandt-Watson, H.J. du Plessis, and G.D. Marshal. Aug. 1988. 17 pp. Productivity and technology The Metalurgical Society and Geselschaft Deutscher Metalhuten-und-Bergleute are sponsoring the Symposium on Productivity and Technology in the Metalurgical Industries, which is to be held in Cologne, West Germany, from 17th to 22nd September, 1989.Non-ferrous smelting Commemorating a centenary of lead smelting and refining at Port Pirie, the Conference on Non-ferous smelting wil be held at Port Pirie from 17th to 20thSeptember, 1989. International trade fairs From 20th to 26th May, 1989,4 major international trade fairs wil be held in Disseldorf, West Germany.

Jan 1, 1988