Search Documents

By R. V. Ramani, K. Bode

"IntroductionThe theory of particle dispersion and deposition in turbulent flow is important to many fields of science and engineering. Dispersion has been studied in some detail since the early fifties (Taylor, 1954; Fischer, 1967; Osipov and Grekov, 1968; Skobunov, 1970 and 1973; Klebanov and Martynyuk, 1974). A broad research effort has also been underway in studying the mechanics of dry particle deposition. Friedlander and Johnstone (1957) proposed a theory, according to which particle deposition from vertical pipe flow could be described by an eddy diffusion transport followed by a final flight to the surface. There have been numerous revisions and additions to this original theory (Owen, 1960; Liu and Agarwal, 1974; Liu and llori, 1974; El-Shobokshy and Ismael, 1980) The mining process essentially consists of breaking in situ materials and transporting them out of the mine. An inherent characteristic of this process is the generation of fine particles. Fine airborne particulates are associated with a number of threats to the health of the miners; fine coal dust can also result in mine-wide catastrophic incidents such as dust explosions. For these and other reasons, it is important to understand the behaviour of airborne dust particulates, particularly their generation, entrainment, transport, dispersion, and deposition in the mine environment for their control.Mine related studies on dispersion and deposition have been few. Yet, several studies of gas and dust dispersion, diesel exhaust contamination, and methane ingress into mine workings have recognized the need for developing reliable parameter values for fundamental understanding of the phenomena (Da""Yes and Slack, 1954; Hodkinson, 1957; Hodkinson and leach, 1958; Mass and Wildschut, 1966; Airey, 1969; Courtney et al., 1986; Stefanko, Ramani, and Thakur, 1974; Stefanko, Ramani and Kenzy, 1977; Bhaskar, 1987, Bhaskar and Ramani 1990; Qin and Ramani, 1989; Shankar and Ramani, 1990)."

Dec 1, 1995

By A. B. Hooker, Iilsley. L. C.

"Flame safety lamps have been used for about one hundred years in coal mines where a dangerous accumulation of explosive mine gas (methane) might occur and thus render the use of ordinary unprotected flame lamps dangerous. Flame safety lamps are not only used for illumination, but also for detecting the presence of dangerous percentages of methane mixed in the air of the mine.The safety of the lamp depends chiefly upon the cooling qualities ofThe safety of the lamp depends chiefly upon the cooling qualities of the wire gauze used to permit free circulation of the air through the lamp. If one enters a part of the mine where methane is present in the air, the methane enters the lamp and coming in contact with the wick flame is ignited and continues to burn within the gauze without igniting the methane surrounding the lamp. If the air within the mine is traveling at a velocity of several hundred feet per minute the burning gases may be driven through the gauze by the air current. If the gauzes are properly designed and of the proper material, these burning gases will be so cooled as they pass through the gauze that they will not cause an ignition of the gas surrounding the lamp. In order to test the effectiveness of a given safety lamp, tests are made in moving explosive mixtures of gas and air arranged to simulate mine conditions.The Bureau of Mines investigated many features relative to the safety of flame lamps and in 1915 established an official schedule known as Schedule 7 whereby flame lamps having certain prescribed qualifications would be approved as permissible for use in gaseous mines."

May 1, 1920

By R. M. Gammell

"INTRODUCTION The Farmer prospect was examined by W. R. Green, an engineer of the Bureau of Mines, in June 1944. As a result, studies of this property were included in a general preliminary investigation of the Etevens County lead-zinc deposits by the Bureau in 1945. The exploratory work was designed chiefly to supplement the surface examination by determining the nature of the mineralization below the zone of oxidization. The results of the small-scale diamond-drilling program undertaken at the property are presented in the following report.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization our resources to the end that they make the greatest possible contribution to security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work and prepares the filial report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Mar 1, 1947

By L. G. Austin

"This paper is based on the development of the Maza-Austin technique for characterizing thousands of coal particles by approximate analysis of the major inorganic constituents Ca, Al, Si, K, Na, Fe and S in each particle. The technique has sufficient sensitivity to work on small volumes, is fast enough to handle large number of particles within a reasonable period of time, and consists of scanning electron microscopy combined with energy dispersive x-ray spectrometry (SEK-EDS). A computerized SEK-EDS system that allows the automated analysis of hundreds of coal particles per hour' is described. The analysis is based on the location and tracing of coal particles embedded in a polished specimen, the selection of sampling points on the traced particles, the collection of an x-ray spectrum from each sampled point for a defined period of time, and the processing of the x-ray intensity to calculate point composition using ZAF corrections. Procedures for correcting for dead time, background, detector efficiency and spectrum overlap are described. These corrections are essential if reasonably accurate analyses are to be obtained from unknown complex mixtures of the elements in a coal or fly ash particle. Examples are given. INTRODUCTION Coal is a complex mixture of organic and inorganic materials. The inorganic fraction is referred to as mineral matter (Gluskoter, 1978) but can occur in three modes: (i) an observable mineral species; (ii) as cations held by ion exchange to carboxylic groups; and (iii) in chelate complexes. The mineral matter content normally represents a significant proportion of a coal, with an average value of about 15% for US coals (Gluskoter, 1975). The standard methods of analysis of the mineral matter in coals are performed on a sample selected to represent the whole coal as closely as possible, and give the overall inorganic composition in the coal. Such analyses are of limited use for solving problems originating from the behavior of individual coal particles, whose compositions vary widely from the average value. This is particularly true in pulverized coal combustion, where the current methods of predicting the slagging and ·fouling potential of a coal are based on the bulk ash composition, but the fly ash particles which create the deposits originate from coal particles with large differences in mineral compo1ition. Some examples can be found where, in a comparison between two coals, the one with the smaller slagging potential according to the mean ash composition was the one that behaved worst in the furnace (Moza et al., 1980; Koza and Austin, 1983). The u1e of gravity fractionation to assess the slagging potential of pulverized coals has shown that conventional ASTM analysis is not sensitive to differences in the distribution of mineral matter when comparing coals (Borio and Narciso, 1979). Bryer (1979) concluded that coals should be examined for fouling and slagging potential by analyzing gravimetric and size-fractionated coal, preferably pulverized· and ground to the size expected at the mill outlet."

Jan 1, 1989

Vanadium, molybdenum, and a titanium-10 percent vanadium alloy were evaluated for their susceptibility to stress corrosion cracking in a number of corrodents. Tests were conducted utilizing conventional U-bend techniques with subsequent evaluation in a pneumatic constant-load apparatus. Vanadium and molybdenum were generally resistant to stress corrosion cracking in the media studied. U-bend specimens of vanadium showed evidence of stress corrosion cracking in 6 li hydrochloric and 18 li sulfuric acids; however, tensile stress specimens exposed to these solutions did not exhibit stress cracking. Similar results were obtained when U-bend specimens of molybdenum were immersed in 10 percent formic acid. Titanium-10 percent vanadium alloy was susceptible to stress corrosion cracking in 10-percent (2.85 li) hydrochloric acid solution. Heat treating the alloy greatly reduced its corrosion rate and its susceptibility to stress cor-rosion cracking in this medium.

Jan 1, 1965

By L. J. Kane

Several processes being developed by the Federal Bureau of Mines to provide new and more efficient uses for coal require practical methods for removing dust from hot gases. Filters provide such means. The efficiency of filters made of aluminum silicate fibers and porous stainless steel was determined. The results obtained with the fibers were previously reported.5 In this investigation tests were made with three porosities of stainless steel filter material (grades C, D, and E) at a gas flow of 1,000 std. c.f.h./sq. ft. of filter, temperatures of 75° and 1,000° F., and dust loadings (as represented by cumulative dust fed) of 100, 1,000, and 10,000 gr./sq. ft. of filter. Pressure drop during the runs ranged from 0.1 to 21 in. of mercury, and dust removal from 25 to 99.93 pct. Filters having the finest pores gave the greatest pressure drop and percentage of dust removal; however, their dust-holding capacity was slightly lower. Usually, their ability to remove a higher percentage of dust at the same pressure drop more than compensated for the slightly lower dust-holding capacity. With increase in temperature, for the same weight rate of flow of gas, the pressure drop increased and the percentage of dust removal decreased. The effect of temperature was probably due to the accompanying change in the linear velocity and viscosity of the gas.

Jan 1, 1961

By J. M. Mutmansky

"The objective of this study was to produce coal dusts for laboratory research that are similar to mine airborne dusts in chemical, mineral, and physical characteristics. In this investigation, dusts produced in laboratory comminution equipment were compared with continuous miner- generated dust for similarity in physical characteristics. Mining-generated dust (MGD) and bulk coal samples were first collected from an underground mining operation. The bulk samples were then processed in the laboratory for size reduction in various comminution devices. These laboratory- generated dust (LGD) samples were subjected to size and microscopic analyses. Physical properties of the dust particles were studied on a scanning electron microscope (SEM ). A numerical shape coordinate system (SCS) was also developed and applied to 300 particles from each sample. Statistical analysis was then performed on the collected data and characteristics of the MGD and LGD samples were compared. IntroductionIn many biomedical studies, researchers routinely introduce a dust mass into an experimental environment to assess the response of a biological entity, usually lung macrophages in vitro or a live laboratory animal, to the dust mass. To provide data of maximum usefulness, it is highly desirable to use dust with characteristics of actual mine airborne dust. The primary objective of this research was to produce dusts in the laboratory similar in chemical, mineralogical, and physical characteristics to mine airborne dusts. This paper outlines the evaluation of the physical characteristics of the lab-generated dusts.Particle shape analysis is perhaps the least-developed area in mineral-related particle science and technology. There are still no standard methods or instruments to scientifically quantify particle shapes. To date, many attempts have been made to characterize particle shapes. These procedures can be roughly classified into three categories:"

Dec 1, 1995

By Lars Osen

This investigation was undertaken to contribute to the understanding of underground pull tests by conducting laboratory tests under closely controlled conditions. Steel bolts, instrumented with electrical resistance strain gages, were anchored in an aluminum block, a granite block, and a steel sleeve, and were subjected to pull tests. The bearing plates used were either flat7 dished, or embossed. In pull testing a bolt that is prestressed, there is a range of loading during which bolt load is greater than the jack-applied load, This study showed that preload, the size, shape, and type of bearing plate; and the geometry of the system determine the point at which bolt load and applied load become equal. The effects on bolt load of both a theoretical solution and actual pull tests were analogous and led to similar results.

Jan 1, 1965

By Edward F. Divers

Tills U.S. Bureau of Mines report briefly evaluates the advantages and disadvantages of basic dust control techniques presently used by U.S. coal preparation and mineral processing plants. These include ventilation, baghouse-type collectors, wet scrubbers, electrostatic precipitators, source control, sprays, good housekeeping, and personal protection devices. Two specific problems in these types of operations are also considered: dust collector system duct clogging, and control room dust control. Information provided in this report results from dust control research projects conducted by the Bureau at various coal preparation and mineral processing plants over the past decade to reduce workers' dust exposure. These studies indicate that plant ventilation systems normally provide the most cost effective method for dust control. Baghouses and scrubbers were also effective in specific applications, and examples of each are given. In extreme dust conditions, personal protection devices, such as respirators or the dust helmet, can also be highly cost effective.

Jan 1, 1990

By F. N. Kissell, C. D. Litton

This study ranks the factors impacting survival during a coal mine fire. It bas already been established that reducing time delays is the most important factor in saving lives. Consequently every event during afire is measured in terms d its duration, and the effectiveness d any action taken to improve survival is measured in terms d the time it saves. By ranking actions according to time saved these authors found that a comhination d actions was most effective. This combination was: • installing lifelines. • moderately decreasing air leakage and • decreasing the fire growth rate. Changing ventilation leakage alone was much less effective, as was altering the CO (carbon monoxide), sensor alarm threshold. These results confirm an earlier fault-tree study on escape from mine fires. The fault-tree study bad shown that, with the exception d delays, single factor changes have minimal impact. Significant reductions in fire fatalities only take place with multiple factor changes.

By G. W. Weems

The Bureau of Mines combined preconcentrating techniques and mass spectrometry to develop a parts-per-billion general analysis of impurities in helium. The impurities are preconcentrated using a Bureau trace-impurity analyzer; 35-mm Hg pressure of helium is left in the concentration trap to sweep the impurities into the mass spectrometry and provide a 10-mm Hg sample pressure.

Jan 1, 1966

By A. W. Khair, L. D. Gehl

"This paper describes the mechanism of coal and rock cutting from quasi-static indentation through dynamic indentation to rotary cutting. The results indicate that during quas~static indentation, a crushed zone, and subsurface fractures develop. The crushed zone is a potential source of dust generation. Dynamic indentation produces a crushed zone due to the frictional resistance offered by the coal or rock during penetration of the bit. Confining pressure changes the mode of failure from tension to mixed tension and shear. The wider bit causes larger crushed zone and more dust generation. The rotary cutting is a combination of quasi-static and dynamic indentation which results in chip formation. 1. INTRODUCTIONThe trend from conventional mining to continuous machine-cutting of coal, using more productive machinery is inexorable. Intolerable levels of dust generated at the face is an indication of inefficient coal or rock cutting by these machines. The Federal Government of the United States paid about 11.7 billion dollars workman compensation to more than 470,000 miners with Coal Workers Pneumoconiosis (Newmeyer, 1981). Bieniawski and Zipf (1985) reported that annual benefit payments were about 2 billion dollars. The need for research m improving coal cutting 1s therefore paramount. The enactment of Health and Safety Act in 1969 in the United States triggered the initial investigation into coal cutting mechanism and cutting tool design. The European countries were also engaged in the same area of research, however, their emphasis was in the use of wedge shaped bits. In 1981, the United States Bureau of Mines commissioned the South West Research Institute to investigate the effect of operating parameters mainly on airborne respirable dust in order to provide a healthier and safer atmosphere for coal mine workers.A research program by the Department of Mining Engineering, West Virginia University, USA was initiated to study the fragmentation mechanism during coal/ rock cutting. The research program was divided into three areas of research, namely quasi-static indentation, dynamic indentation and rotary cutting."

Dec 1, 1995

By C. J. Johnson, C. J. Bise

"As the US coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face-ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity.Room-and-pillar mining accounts for approximately 68% of the nations underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing technological climate on future room-mid-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.IntroductionThe ultimate goal for any coal mining company is to effectively use its human and financial resources to maximize its profits through the extraction of its reserves. Although recent workforce reductions in the industry have resulted in a more efficient use of labor and increased productivity, there comes a point in time when further reductions in the numbers of workers in each operating section are impossible with existing equipment. For example, Farinelli and Bise (1987) found that labor cost constituted 62% - 73% of the cost per ton of coal at the mining section, with a minimum crew size. Thereafter, efforts to increase productivity must focus on more efficient mine plans and technology.The fact that an increase in productivity can be realized by reducing non-productive time (change-out and tram time) and converting it to productive time has been known and demonstrated for quite some time. What has not been demonstrated frequently is the quantification of the potential productivity increase of currently emerging technology or ""add-on"" equipment. It is one thing to be able to say that a piece of equipment will make an operation more productive, but it is another thing to be able to quantify the productivity increase that will justify the purchase of the new equipment. Not only is a financial benefit possible in room-and-pillar mining with an increase in productivity, but a decrease in the time necessary to develop a longwall panel can also occur.The purpose of this paper is an analyze the impacts of a changing technological climate on future room-and-pillar operations by comparing a base-case section (current) to several scenarios incorporating emerging technology. To do this, four cases will be developed. A base case, consisting of the typical manner in which continuous-miner sections are currently operating, is compared to three layouts incorporating: (1) flooded-bed scrubbers on radio remote-controlled continuous miners, (2)a continuous miner with side-mounted roofbolters, and (3) a continuous miner with side-mounted roofbolters used in conjunction with a continuous-haulage system."

Jan 1, 1989

By J. C. Hartley

The most important single operation in mining is the ventilation of underground areas in a manner conducive to the health and safety of employees. Adequate volumes of pure air must be supplied at the working faces, along the haulageways, and wherever men work, so as to dilute and carry away the methane liberated from the coal and adjoining strata, noxious gases evolved by the use of explosives, and the carbon dioxide exhaled by men and formed by oxidation of carbonaceous material, as well as any other gases, and also dusts which may be found in mine workings. A sufficient quantity of air must also sweep abandoned or worked-out areas of the mine to prevent the accumulation of gases, where sealing methods are not utilized to isolate old workings. Air, in a quantity adequate to meet the needs of the particular mine to which it is applied, is necessary, and supplying it can be made very expensive through failure to observe good practices in its direction and apportionment." Leaky stoppings, doors, and overcasts rob the working faces of air and add to the ventilating cost by burdening the fans with fugitive air,

Jan 1, 1944

By Charles A. Seitz

This Bureau of Mines report describes an automatic and continuous transducer-drift compensator. The compensator formed a part of the instrumentation used to indicate the saturation by hydrogen of a cryogenic, adsorption column. It has a variable delayed-response characteristic and will respond only to signals having rise times faster than component drift times. Zero drift due to varying ambient conditions and component aging is nullified. Equations relating the output as a function of the input signal are given.

Jan 1, 1981

By Arthur Metcalfe, Edward Thomas, A. J. Barry

"Early in 1947 the Bureau of Mines became interested in adapting suspension roof support to coal mining 5/ as a possible means of reducing the high rate of accidents from falls of roof. For a time the program made little progress be¬cause of the shortage of steel products after the end of World War II, but during the past 8 months this restriction has eased, and as of May 1, 1949, 114 mines had either started experimental work or had ordered materials and equip¬ment in anticipation of trial installations. It is estimated that 30 linear miles of roof in underground passageways have been secured by this method in recent months, and no lost-time roof-fall accident has been reported in these areas up to that date.Many coal-mining companies in widely separated localities have cooperated in making experimental installations. In very few instances are these companies entirely satisfied that they have arrived at the best solution in determining the most efficient adaptation to suit their particular conditions. Moreover, new ideas and modifications of the basic principle are constantly being brought to light and are being tested. Available test data is far from complete, and it is conceivable that some new idea will be developed to alter the present concept of proper technique; therefore, this progress report does not attempt to answer all questions that might arise in connection with this method of roof support; it simply recounts the experience acquired to date. Consequently, few references to costs are made. Up-to-date quotations on material and equipment used in suspension roof-support installations may be obtained from numerous mine-supply companies.The authors gratefully acknowledge the cooperation of mining companies whose personnel made possible collection of the information contained in this circular: Bethlehem Collieries Corp., Barrackville, W. Va.; Berwind-White Coal Mining Co., Windber, Pa.; Consolidation Coal Co., (Ky.); Jenkins, Ky.; Consolidation Coal Co. (W. Va.), Fairmont, W.Va.; Clinchfield Coal Corp., Dante, Va.; Consolidated Coal Co., St. Louis, Mo.; Hanna Coal Co., St. Clairsville, Ohio; Missouri Portland Cement Co., Sugar Creek, Mo.; Pocahontas Fuel Corp., Pocahontas, Va.; Reppert Coal Co., Dola, W. Va.; St. Joseph Lead Co., Bonne Terre, Mo.; and Tennessee Coal, Iron, & Railroad Co., Birmingham, Ala.The fundamental theory of suspension roof supports is not new; in fact, its application in the construction of beams predates mining itself. The basic principle involved is the reinforcement of roof rock with steel rods inserted in the roof and anchored therein at points where the rock is least likely to be affected by stresses resulting from mining. Such roof supports have been used in mines for many years in widely separated localities. The St. Joseph Lead Co., operating in southeastern Missouri, apparently was the first large mining company to prove the practicability of the principle by applying it in a systematic manner for securing roof for more than 20 years (fig. 1)."

Sep 1, 1949

By R. T. Johansen

The wettability of petroleum reservoir materials by water and crude oil has been recognized as an important factor in determining waterflood behavior. The problem of simulating and studying reservoir conditions and characteristics, to produce laboratory results congruous with field experience, has been examined by many methods. (1, 2, 3, 4).4/ The most generally accepted approach to this problem is determining wettability of the porous medium by imbibition methods; or, after solvent extraction, predetermining the wettability of the samples by coating the surface of the medium to render it preferentially oil-or water-wet (3, 5). The emphasis of wettability studies has been placed on the characteristics of the reservoir materials with little consideration being given to the fluids themselves. Therefore, the wetting tendencies of crude oils have been investigated by a recently developed method (6). Imbibition and the more general phenomena of capillary pressure are the most direct ways to measure wettability. The simplest type of capillary pressure observations involves the use of an interfacial-tension capillarimeter, which does not produce as separate values either interfacial tension or contact angle. Actually, these quantities do not have independent significance in reservoir engineering, and the property of wettability they are intended to evaluate is given, immediately by capillarimetric measurements.

Jan 1, 1961

By A. B. Hooker

Nineteen of the installations were on rental contracts 1.L."'1der whtch the lamps belong to the lamp company and are rented by t.½em to the mine operatj.nt; company. · The other nine installations had been upon an O\Vnership-rental basis, by which the lamps had become the property of the renter at the end of 5 years. Five of t.11e rentec installations were en a special contract calling for a guaranteed light output. These contr2.cts were based upon certified . initial performance, with the provision that the lamps be replaced whenever periodic tests of fully charged lamps, taken at random from t..h.e charge racks, showed a light output of less than 80 percent of the certified performance.

Jan 1, 1942

By H. E. Perlee

The concentration limits of flammability and autoignition temperatures of trichloroethylene in atmospheres of air, oxygen, and nitrogen tetroxide have been determined in a spherical vessel. The autoignition temperatures of TCE in atmospheres of air, oxygen, and nitrogen tetroxide were found to be 419°, 396°, and 221° C, respectively. The flammability zones of TCE-air, TCE-oxygen and TCE-nitrogen tetroxide mixtures at 100° C were found to be 10.5 to 41, 7.5 to 91, and 13.5 to 69 volume percent TCE, respectively. In addition, maxi-mum combustion pressures of 50 ps and 140 were recorded for constant volume combustion of the lower limit mixtures of trichloroethylene in air and oxygen, respectively.

Jan 1, 1966

By A. J. Miscoe

A unique machine for inducing bending fatigue in wire ropes was built at the U.S. Bureau of Mines' Pittsburgh Research Center. This machine can produce nine levels of degradation through repetitive cycling of long samples of wire ropes of the types used in the mining industry. This report provides an analysis of the results of the first wire rope to be fatigued on this machine. These results have indicated that as a wire rope accumulates bending cycles, its strength first decreases because of wear and then in-creases due to cold working of the wires. As the amount of cold working increases, more and more of the embrittled wires break and the strength of the rope decreases rapidly. In this test, application of several of the regulatory retirement criteria to various sections of the rope suggests that there may be some inconsistency among them.

Jan 1, 2010