Search Documents

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 3. t. u. compared with 597,000 3. t. u. in 1936. These amounts represent roughly the heat ob¬tainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at rep aeries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels wore 11 percent higher than in 1930; the average operating ratio was 93 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 639,149 billion 3. t. u. in 1936 to 663,966 billion 3. t. u. in 1937.

Jan 1, 1938

By J. C. Holtz

Since 1937 the Bureau of Mines has conducted investigations to provide the technical information necessary to guide the safe use of diesel engines underground in the United States. Coincident with the beginning of the technical study, a survey was made of State regulations pertaining to the use of internal-combustion engines underground.3/ At that time it was found that owing to the known hazards of gasoline locomotives, many States had enacted legislation or regulations limiting or prohibiting their use underground. Some of this legislation prohibited, or could be interpreted as prohibiting, the use of any type of internal-combustion engines in underground workings. After World War II diesel-powered equipment was introduced underground in many States, and pertinent questions are received frequently by the Bureau of Mines about the regulations that permit such applications. Because it was known that new and revised regulations had been made effective in some States in the nearly 20 years that have elapsed since the previous survey,3/ the Bureau decided that a review of the latest regulations in the leading mineral-producing States would be a valuable source of information for those engaged in the production of minerals as well as others. Accordingly, where feasible, this report includes abstracts of State laws and regulations as they affect the use of internal-combustion engines underground, particularly diesel engines. The substance of comments from State officials also are included when these appear to be helpful to interpretation of the regulations.

Jan 1, 1957

By A. B. Hooker

Since man first mined underground, there has been need for adequate illumination; this need has never been fully supplied. At first, suitable lamps were not available. Gradually they have been developed, but along with that development the need for better and better lamps has continued owing to the following conditions and factors: 1. Increasing hazards from gas and dust ignitions. 2. The speeding of operations with mechanized mining, which necessitates greater visibility. 3. A demand that cleaner coal be loaded, which requires higher levels of illumination. 4. The cost of compensation for injuries that has created a demand for better illumination and safer lamps. Use of better lamps has been retarded by: 1. Prejudice and resistance to change on the part of the workers in some districts. 2. The cost and upkeep of the lamps. 3. The present types of lamps, while a great improvement over the old lamps, do not entirely fulfill the requirements for a safe and efficient light for underground workers.

Jan 1, 1938

By J. B. Littlefield

The term "konimeter" is used generally to designate a type of dust-sampling instrument that collects the dust from a small volume of air by impingement on a glass plate prepared aced with an adhesive film. The konimeter was first developed by Sir R. N. Kotze about 20 years ago and was followed a few years later by the circular-type konimeter, by which a number of samples may be collected on a glass disk. The present discussion will be confined to the circular type, as it is used most. Various techniques have been developed for using the konimeter, and many materials, such as petrolatum, mineral oil, and glycerine jelly, have been used in preparing the adhesive film. In South Africa, Australia, and Canada, where the konimeter has been employed most widely, dust samples are treated by ignition and washing before being counted. In Canada the dust samples are collected on a disk of special heat-resistant glass prepared with a film of mineral oil; the disk is then heated to a dull cherry-red in a muffle-furnace to remove the film and organic matter, cooled, and washed with a few drops of 50-percent hydrochloric acid followed by distilled water and alcohol, and then heated again to remove residue left by evaporation of the alcohol. After this treatment, the dust samples are counted under a magnification of 150 diameters with dark field illumination.

Jan 1, 1938

By M. G. Downey

The stone resources in certain localities and the kinds of stone available often influence manufacturing companies in their choice of plant location and in possible expansion of their activities. Limestone in particular is an important raw material for many processing industries. In planning highways and public works and placing contracts therefor, the availability of aggregates and road stone is significant. On the other hand, persons who contemplate entering the stone business or opening now quarries need information as to possible competition. To meet the growing need for regional data of this type, the Bureau of Mines has compiled from its records and presents herein the location of stone quarries by States and counties and by kinds of stone. The list covers all stationary and portable commercial quarry operations whose production statistics for 1940 were reported to the Bureau of Mines but does not include undeveloped deposits and noncommercial or Government-operated quarries.

Jan 1, 1941

By L. C. IlsLey, Charles M. Means

The descriptive rather than the strictly technical meaning of many of the terms and expressions used in the electrical rules is given in order to assist in their interpге- tation . ALIVE . At a potential measurable with a voltmeter and different from that of the earth or another conductor . (Static charges should be determined with an electrostatic voltmeter . This condition may apply to current - carrying parts , to noncurrent - carrying parts and adjacent material where a failure of insulation has taken place , and to objects having stored or static electricity . ) ALTERNATING CURRENT . A current that changes in direction -- positive or negative-- a certain number of times per second , depending upon the number of poles and speed of the generator . AMMETER. An instrument for measuring current , indicating in amperes . AMPERE . A term applied to denote the rate of current flow . ( Analogous to " gallons per minute " in a hydraulic system . ) APPROVED . Accepted as suitable by a competent committee , board , or organization designated by those adopting the rules . ductors . ARMOR . A steel or equivalent metallic covering for one or more electric con- AUTHORIZED PERSON . Anyone commissioned by the official in charge of the mine or his deputies to carry out certain duties incident to the generation , transformation , and distribution or use of electric energy in the mine , such person being one who is competent within the purpose of the rule in which the term is used .

May 1, 1930

By W. Wallace, T. Ong, M. Gautam, M. Keane, S. Xing, J. Harrison

"Diesel exhaust soots were assayed in the Ames Salmonella typhimurium histidine reversion assay system using TA 98, the soots being applied as the following preparations: dispersion in dipaimitoyl glycerophosphoryl choline (DPL), dispersion in dipalmitoyl phosphatidylethanolamine (DPP!), and dispersion in dipalmitoyl phosphatidic acid (DPPA) in physiological saline, and in physiological saline without added surfactant. The extracts of soots by dichloromethane / dimethylsulfoxide (DCM/BHSO) were also assayed. Studies were performed both with and without :IQ microsomal activation of the soot preparations. The DPP! and DPPA surfactants were chosen as phospholiridz with two palmitic acid moieties esterified to a glycerol as is the case with DPL, but with hydrophilic groups having different electrophilic characters. The soots, without S9 activation, showed mutegenic activity when extracted in the conventional procedure with DCM/DMSO. The mutagenic activity of soots dispersed in DPL was quantitatively comparable to, and in some cases greater than, the activity expressed by an equal mass of soot extracted by DCM/DMSO. Soots in other surfactantpreparations, DPP! and DPPA, also expressed positive mutagenic activity. Praincubation with S9 microsomal enzyme fraction reduced the activity of solvent extracted soots, and greatly diminished the activity of DPL dispersed soots. Initial sister chromatid exchange (SCE) assays using the Chinese hamster V79 cell line indicated DPL dispersed soot also can cause SCR in mammalian cells. Results thus far suggest that surfactant suspended or ""solubilized"" respirable soot particles could provide a mechanism for transport and expression of mutagens in the lung."

Jan 1, 1989

By Oliver A. Dibble

This paper it one of a series being prepared for and published by the United States Bureau of Mines, describing mining methods and costs at clay pits throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The open-pit recovery of clay for cement plants is a comparatively simple operation in comparison with underground mining of clays; nevertheless, it represents an appreciable factor in the cost of cement manufacture. The following report deals specifically with the methods employed by the Aetna Portland Cement Co., which operates cement mills at Fenton and Bay City, Mich., in recovering clay from their pit at Corunna, Mich., on the Grand Trunk Western Railway.

Jan 1, 1932

By F. F. Hintze

In the group of minerals used in making this study, the cyanite is associated with quartz, mica, and feldspar in the schist. The amount of quartz is variable, but it is always an abundant mineral. Both large and small crystals of quartz occur in irregular masses, rarely ever showing crystal outline. Mica is of the clear and dark varieties, the larger crystals being dark as a rule, and the finer crystals of light color. The present mineralogical composition of the mina is rather variable, as most of the original biotite and muscovite have suffered alteration, and much secondary mioa is present as a result of alteration of the original mica and other minerals present, especially the larger cyanite crystals. A large part of the mica now found in the ore is chlorite, with varying amounts of Jefferisite and others, especially sericite. These are in the form of aggregates, or felt-like intergrowths filling the spaces between the quartz, cyanite, and feldspar.

Jan 1, 1931

By F. W. Hoertel

The effects of certain process variables on the grain size, grain type, and microhardness of vapor-deposited tungsten were established, and the near-optimum parameters and the efficacy for the vapor deposition process were determined. No significant change in the grain size or microstructure resulted from ultrasonic vibration of the substrate during deposition, from variations in the hydrogen (H2) to tungsten hexafluoride (WF6) ratio, or from small increases in reaction-chamber pressure. Near-optimum conditions were continuous deposition at atmospheric pressure, a deposition rate of 2-mils thickness/square inch of substrate area/hour, a temperature of 5500 C, and a hydrogen to WF6 ratio of 4:1. The addition, individually, of about 2 volume-percent of butane, 24 volume-percent of carbon dioxide, or 4 volume-percent of propane to the hydrogen and WF6 mixture produced deposits with the finest grain size for each gas. A corresponding increase in microhardness accompanied the decrease in grain size. The addition of gases did not alter the columnar microstructure found in vapor-deposited tungsten.

Jan 1, 1966

By N. F. LeJeune, Earl C. Lane

This is the third of a series of reports on a survey of petroleum prod- ucts manufactured on the Pacific Coast from California crude oils. California crudes differ in many characteristics from the petroleum produced in the other parts of the United States, and the claim has been made that some of the present Federal Specifications for petroleum products tend to discriminate against Cali- fomia products. The purposes of the present survey are to determine what par- ticular specification requirements Califomia petroleum products characteristical ly fail to meet, how widely the products deviate from these requirements, and if possible to show whether the fault lies with the specifications or the products, or along what lines investigation to determine this question should proceed. The first report of the series gave the physical and chemical properties of the samples of gasoline and mineral spirits. A second report**, gave the physical and chemical properties of samples of lubricating oils. The present report deals entirely with burning and fuel oils. The refin ing companies have continued their very cordial and helpful cooperation. Seven samples of kerosene, four samples of Diesel fuel and eight samples of fuel oil were obtained. The methods of analysis used are those adopted by the Interdepartmental Petroleum Specifications Committee, published by the Bureau of Mines in Technical Paper No. 323. The specifications used for corparison are those officially adopted by the Federal Specifications Board for the use of the various Depart- ments and Independent Establishments of the Government, effective February 3, 1923, and published by the Bureau of Mines in Technical Paper No. 323, Part 1. Specific gravity, degrees A.P.I., viscosity and other special tests al- though not required by the specifications have been given for comparison. All temperatures are recorded in degrees Fahrenheit. Tables have been prepared giving data on physical and chemical propertios of the individual samples. Before each table the classification and specifica- tions for the particular class of oil considered in the table are given. Follow- ing each table, brief notes show wherein samples deviate from specification re- quirements.

Aug 1, 1923

[ ]

Jan 1, 2012

By F. F. Hintze

In the group of minerals used in making this study, the cyanite is associated with quartz, mica, and feldspar in the schist. The amount of quartz is variable, but it is always an abundant mineral. Both large and small crystals of quartz occur in irregular masses, rarely ever showing crystal outline. Mica Is of the clear and dark varieties, the larger crystals being dark as a rule, and the finer crystals of light color. The present mineralogical composition of the mina is rather variable, as most of the original biotite and muscovite have suffered alteration, and much secondary mica is present as a result of alteration of the original mica and other minerals present, especially the larger cyanite crystals. A large part of the mica now found in the ore is chlorite, with varying amounts of Jefferisite and others, especially sericite. These are in the form of aggregates, or felt-like intergrowths filling the spaces between the quartz, cyanite, and feldspar. The feldspar is plagioclase probably mostly albite. It is white, possesses good cleavage, and is one of the hard brittle minerals of the rock. It alters to kaolin, and sericite, and more or less of these alteration minerals are present within the feldspar crystals but not separated from them. The cyanite is of two varieties, distinguished by their colors as blue and white cyanite. The blue color varies in intensity, being a pronounced blue in some crystals and paler in shade in others. Some crystals have been seen which posses the blue color in one-half of their mass and are pure white or clear in the other half. The purity of the cyanite is probably not affected by the color, but it is difficult to detect the white cyanite in the ore by macroscopic examination, so that great care has to be exercised in the selection of the ore in the field. Of the above minerals, cyanite is the heaviest, having a specific gravity of 3.6; none of the others approach it in specific gravity. The usual as opiates of cyanite in the mica schists are garnet, magnetite, and tourmaline, but these have not been noted in the group of minerals treated, and their absence is a point of great value in favor of this ore, as they possess high specific gravities and interfere in separation processes, and if not separated they are detrimental because of their easily fusible character. Small amounts of apatite and titanite have been noted, but not enough to cause trouble.

Jan 1, 1931

By E. H. Denny

A most interesting safety record has been made by the Colorado Fuel and Iron Co. s. Robinson ho. 1 mine located at Walsen, Cola. Mr. J. L. McBrayer has been superintendent of the Robinson No. 1 and 2 mines for the past 2 1/2 years, and Mr. David Muir has been foreman of the Robinson No. 1 mine since June, 1913. The last fatal accident at Robinson No. 1 mine occurred on July 27, 1915, and the tonnage produced at this mine since July 28, 1915, has been as follows:.

Jan 1, 1929

By L. B. Berger

In this investigation, the ampoule type of carbon-monoxide (CO) detector which is manufactured under license of U. S. Patent 1,644,014 (October 4, 1927) was tested for sensitivity and reliability. This detector was devised primarily for examining the air of manholes and sewers for possible dangerous contamination with CO before workman enter those places, but dine to the simplicity of the device it may have a more general usage for examination of atmospheres which are known or suspected to be contaminated with CO. Some of the suggested uses are the examination of the air in garages, tunnels, mines, around blast furnaces, gas plants, and in the home.

Jan 1, 1930

By Ronald D. Hill, Elmore C. Grim

1.In 1972 over 595 million tons (51+0 million metric tons) of bituminous coal were mined; 49% of this tonnage was obtained by surface mining methods. Authorities have predicted that the tonnage of surface mined coal will increase in the future, especially since oil and gas resources are becoming limited. 2. Demands for clean air have increased mining activities in the low-sulfur coal deposits in the West. Pollution problems arising from these operations will be considerably different than those found in the East. The deposits are located in arid to semi-arid regions. Coal seams are generally aquifers and are a principle source of fresh water. Therefore mining may result in alteration of groundwater distribution patterns by aquifer disruption. In general, pollution problems associated with western mining are not well characterized. 3.Since any disturbance of the surface will alter the environment in the vicinity of the disturbance, pre-mining planning is a prerequisite to any environmentally successful surface mining operation. If properly carried out, the adverse social, economic, and environmental effects of coal surface mining will be minimized. Certain land areas will be unsuitable for surface mining where: a.Reclamation is not physically or economically possible. b.Mining is incompatible with existing land use plans. c.The proposed mining area is of critical environmental concern. Core drilling is the most satisfactory method of obtaining accurate information for pre-mining planning. 4. Unaccountable strip mining in the past has created problems that are still present today. Contour mining methods that involve the indiscriminate dumping of overburden on the downslope is one of the largest single sources of sediment from strip mining. However, land disturbed by strip mining can be reclaimed. Techniques have been and are being developed by which mining and reclamation are integrated into a single operation. Mountain top removal, head-of-hollow fill, and block cutting are examples in contour surface mining. These methods drastically reduce pollution problems associated with contour stripping.

Jan 1, 1974

By R. R. Trengove

This paper is one of a series published by the Bureau of Mines on mining methods and operation practices. It describes the open-pit mining method and operations of the Kaiser Steel Corp. Eagle Mountain iron-ore mine, which is in the extreme southeastern part of California 175 miles east of Los Angeles in Riverside County. Nearest town to the mine is Indio, which is 60 miles away by an excellent highway (fig. 1). Elevations at the deposit vary from 1,400 to 3,000 feet. Figure 2 is a plan map of the Eagle Mountain iron mine. Kaiser Steel Corp. built a model camp at the mine, with all modern conveniences (fig. 3). The camp, comprising 145 homes, dormitories, mess hall, commissary, post office, and recreational facilities for 600 people, is at 1,390-foot elevation. The area has winter-resort weather between October and May, with occasional drops of temperature to 25° at night. From June to September temperatures sometimes rise to 1200 during the day. Rainfall is scant, approximately 2 inches a year, the majority of which comes as cloudbursts during the summer months.

Jan 1, 1956

By Suresh K. Bhatt, Dennis R. Dolinar

The roof bolt system of a mine, if properly selected and installed, can allow for better roof control and reduce the potential for roof falls. Because of this potential to reduce roof falls and improve ground control conditions, the National Institute for Occupational Safety and Health (NIOSH) has an interest in the types of roof bolts that are used by the coal industry. Further, NIOSH has conducted research into how various support parameters can affect the number of roof falls that occur, including support type. Today, the five main types of roof bolts installed in U.S. coal mines are mechanical anchor bolts, point-anchor or resin-assisted mechanical anchor bolts, torque-tension bolts, combination bolts, and fully grouted resin rebar. This paper describes each support in detail. Because of the importance of resin in the functioning of the majority of bolts installed, resin grouts are also discussed. Further, trends in the types of roof bolts used are reviewed. Over the last 10 years, the significant trend has been the large reduction in the relative number of mechanical anchor bolts that are installed. These bolts have been replaced mainly by the resin-grouted rebar system. Data are also presented to show the impact of these changes in bolting on the number of roof falls.

Jan 10, 2000

By Robert L. Chufo, H. Kenneth Sacks

Medium-frequency (MF) waves can propagate in a coal seam, bounded above and below by conducting rock, in an approximate transverse electro-magnetic (TEM) transmission-line mode with the electric field vertical and the magnetic field horizontal. The theory of this coal seam mode is applied to recent MF data for a number of mines in order to classify the propagation characteristic of the mines in a simple way. When conductors such as rails, trolleylines, or power cables are present in the vicinity of the measurement path, it is found that the magnetic field versus range plots have two distinct regions with very different slopes. This effect is attributed to coupling of the cylindrically spreading coal seam mode to a low-attenuation conductor guided mode. As a result, voice communications range between mobile transmitters can extend several thousand meters. The use of MF for mine communications is discussed.

By Linda L. Chasko, Larry D. Stowinsky, Ronald S. Conti

Mine operators often rely on mine rescue teams to save lives during an underground emergency such as an underground fire, explosion or roof fall. It is extremely important that team members are provided with adequate exploration equipment and that training simulations are conducted in a realistic manner. A series of mine rescue training exercises was developed, conducted and evaluated by the National Institute for Occupational Safety and Health (NIOSH) in cooperation with the Pennsylvania Department of Environmental Protection, Bureau of Deep Mine Safety. The exercises were conducted at NIOSH’s Lake Lynn Laboratory during 1995 to 1998 and resulted in improved technology and training for mine rescue teams. For example, existing technologies were identified to help rescue teams during exploration. These included chemical light sticks to identify team members and mark crosscuts and mine materials, strobe lights for mapping out escape ways, and a helmet mounted thermal imaging system to see through smoke. A hands-free communication system showed potential for enhanced communications between team members and the fresh air base. A new high-visibility team lifeline that allows for flexibility of movement between team members was developed. A positive-pressure inflatable escape device (IED) was used to isolate the “hazardous” environment from fresh air and allow rescue team members to traverse through. An inflatable feed-tube partition that can rapidly block large openings such as underground passageways and simultaneously provide a feed-tube for high-expansion foam generators was also deployed for several simulations. During the simulations, mine rescue team members donned self-contained breathing apparatuses (SCBA) and traversed more than 305-m of mine passageways filled with nontoxic smoke. Visibility ranged from 0.3 to 0.9-m. In one area of the mine, a kerosene heater was used to simulate a fire and reduce the oxygen concentration. In another area, a 1.5 pct methane zone was established. The team members searched for "victims,” mapped the passageways, built temporary stoppings and ventilated the smoke-filled entries. The teams indicated that the simulations were challenging and very informative.