Search Documents

By R. B. Corbett

"INTRODUCTION Aluminum and manganese bronzes as a group, may be separated readily from other copper-base alloys by experienced sorters. However, separation of aluminum bronze from manganese bronze is generally a matter of guesswork, so that accurate separation presents a difficult salvage problem.Attempts at separation by the thermoelectric tester. 3/ which had proved successful in solving other sorting problems, showed in this instance that the desired separation was uncertain because of the wide range of composition allowable in each kind of bronze. If only one composition of each kind of bronze were used in industry, separation by the thermoelectric method probably would be simple. However; the variability in composition observed in commercial alloys is so great that the thermoelectric power of the one type frequently overlaps the range of values found for the other. As a result, specimens frequently are classified in the' wrong group.Separation of the two types of bronzes on the basis of measurements of magnetic properties on filings from the various samples also proved unsuccessful because the test results overlapped to such an extent that no clear-cut division could be obtained.Electrode potential measurements were made also on the aluminum and manganese bronzes in the hope of distinguishing between them. A drop of saturated potassium chloride solution was placed on the fresh surface of the metal and the tip of a calomel electrode introduced therein. The voltage generated was measured by connecting the electrode and the bronze part to a research-type potentiometer. Although the voltages generated by the manganese bronze parts were greater than those generated by the aluminum parts, the difference in the closest two sets of readings was not sufficient to warrant a good separation. When a concentrated potassium alum solution was used instead of the potassium chloride solution, a wider divergence of voltage was produced by the various bronzes, but unfortunately readings overlapped in several instances."

Nov 1, 1944

By August J. Kwitowski

This Bureau of Mines report describes how the reinforcement mechanisms of untensioned, full-column resin bolts were determined during one underground study. Both axial and transverse shear loadings were identified for two instrumented resin bolts that replaced standard resin bolts in an opera-ting room-and-pillar mining section. The strain responses of resin bolt steel cores to local axial and transverse shear loadings are described. This information was obtained from laboratory testing of resin bolts installations; it was also used to analyze the data from the underground test.

Jan 1, 1980

By L. C. IlsLey

"According to accident statistics, issued from time to time by the Department of the Interior, Bureau of Mines covering fatalities in coal mines, between the years 1870 and 1921 there were 4,897 deaths caused by explosives. The legislatures and safety commissions of the various mining States have Elected and formulated many excellent regulations in regard to the handling and use of explosives in an endeavor to keep this class of accidents as low as possible. An analysis or comparison of the explosive, regulations issued by over thirty States would make a very long paper, however, by subdividing according to phases and issuing several papers it is believed that the material will be more readily available. The first phase was treated in Serial No. 2405 of the Bureau of Mines (""State and Federal Electrical Shot-Firing Regulations,"" issued in October 1922) which gave a compilation of such regulations as apply strictly to electric shot-firing. The second phase under consideration is ""Who may set off blasts in coal mines.""In some States, the person who does the firing must be an ""authorized shotfirer,"" while in other States he must have proved his ability to do this work, and again in other States he is ""any person."" The present paper covers rules and regulations relating to this phase of shotfiring, and those States having similar regulations have been grouped as follows."

Jun 1, 1923

By R. J. SHAW

Oil shale has been defined as, "a compact, laminated rock of sedimentary origin yielding over 35 percent of ash and containing organic matter that yields oil when distilled but not appreciably when extracted with the ordinary solvents for petroleum." The oil-yielding organic matter in oil shale, commonly called kerogen, decomposes upon application of heat to form bituminous materials that are soluble in organic solvents and may be extracted from the inorganic residue. However, separation usually is accomplished by continuing the heating and thereby cracking the primary bitumens to gas and oil, which distill, leaving a carbonaceous material on the mineral residue. It has been suggested that this conversion takes place only at relatively high temperatures - 750°F or higher. On the other hand, other workers have found that transformation may take place to some extent at temperatures as low as 400°F. In either a solvent extraction or a destructive distillation process for separating organic material from the inorganic portion of oil shale, the quantity of heat required to raise the temperature of the oil shale sufficiently to induce a satisfactory rate of conversion of kerogen to oil is important in determining the design of an economical process. Likewise, the quantity of heat recoverable from a spent shale is important in determining the overall heat balance of the process. Published data on the specific heat of American oil shales are meager. Gavin and Sharp present data for two samples of Colorado oil shale, one from near DeBeque and one from Parachute Creek, and for a sample of spent shale over a temperature range of 68°F to 1940°F. McKee and Lydor present data on the specific heat of two samples of oil shale from near DeBeque, Colorado. Additional thermal data on various grades of oil shale over a wider range of temperature are needed in order to apply sound engineering practices to the design of equipment for processing oil shale.

Nov 1, 1947

By T. O. Llewellyn

The Bureau of Mines, as part of its goal to develop technology that can conserve domestic mineral resources investigated beneficiation methods for recovering phosphate minerals from two Southern Florida deposits with high magnesium content. Chemical analyses of sized fractions indicated that no coarse pebble concentrate could be produced from either deposit. Conventional fatty acid-fuel oil batch flotation tests on two phosphate samples, analyzing 6.8 and 8.5 pct P205, yielded concentrates containing 28.97 to 29.80 pct P20S at recoveries ranging from 72.4 to 76.9 pct of the flotation feed. The MgO content ranged from 1.20 to 1.36 pct. Bubbling S02 gas through an aqueous concentrate slurry, further reduced the MgO content of these phosphate concentrates to 0.5 and 0.8 pct, but with a concomitant loss in the phosphate recovery. Settling characteristics of slimes from both phosphate samples showed a slow settling rate, which is a typical characteristic of other slimes in the region.

Jan 1, 1981

By Jan M. Mutmansky, Christopher J. Rise

"One of the most serious long term health problems associated with underground,mining is Coal Workers Pneumoconiosis (CWI'), more commonly known as Black Lung Disease. It occurs in some coal workers, normally after 15 or more years of exposure to coal mine dust, and leads to a variety of respiratory problems. Two types of pneumoconiosis are recognized simple CWP, which has been estimated to affect 6.9 percent of miners and is a condition that does not impair the miner's ability to work nor reduce life expectancy; and a more severe form of black lung (called progressive massive fibrosis) that occurs in about one percent of the cases and results in severe lung damage.Although the relationship between coal dust and CWP has long been recognized, detailed knowledge of the relationship is insufficient for setting up authoritative guidelines to reduce the health risks for those employed in dusty,underground environments. CWP is not only a health problem for workers that causes considerable distress, it is also a very expensive problem the total annual costs associated with CWP approach two billion dollars.As part of its efforts to combat CWP, the U.S. Bureau of Mines in 1983 established a Generic Mineral Technology Center to carry out basic research into all aspects of respirable coal dust:— control of dust generation — the behavior of dust in the mine — characterization of dust particles interaction of dust and lung— the relationships among dust generation and mobility and the mine environment, geology, and seam characteristics,Penn State, West Virginia University, the University of Minnesota, and the Massachusetts Institute of Technology are involved in this research, which is administered from the Department of Mineral Engineering at Penn State.Our work is one of the seven projects to be conducted at Penn Slate. We are concerned particularly with the characterization of dust and its relationships with the mine environment, and our main goal is to establish standard procedures for describing and measuring these variables.Coal DustCoal dust is a very complex material that varies greatly in chemical and mineralogical properties. Moreover, it is not the only constituent of respirable dust in the mine. When a coal seam is mined, it is inevitable that rock particles other than coal are included in the material. This rock comes from the mine roof, the floor, and the partings and inclusions within the coal scams. Since the roof and floor strata, the partings and inclusions are often stronger than the coal, mining them frequently causes more dust than mining the coal itself. One of the objectives of our research is to find the relationships between a specific coal's characteristics before it is mined and the respirable dust characteristics after it is mined. We are particularly interested in the size distribution of particles, the chemical properties, and the mineralogical properties."

Jun 1, 1988

By Hewitt Wilson

[ ]

Jan 1, 1927

By John R. Bitler

A computerized napping system was developed by the Bureau of Mines to provides procedures for the rapid and inexpensive display of coal reserve data. Mapping system output consists of two types of maps, point distribution and contour (isopleth), which can be produced for data (coal analyses) associated with a point location (outcrop, drill core, or mine samples). These locations can be in the form of latitude and longitude or Universal Transverse Mercator (UTM) grid coordinates. The mapping area can range in extent from as small as a single county to as large as a multistate region. The mapping system utilizes programs developed at Harvard University, in addition to several modifications developed by the authors. The primary advantage of this system is that it enables the display of a rapidly changing data base and computerized map generation without the intermediate steps of digitizing and overlaying to produce base maps. The mapping system is applicable to any regional mineral reserve or resource study for which point location data are available. Included are example maps of the distribution of data points and contouring for sulfur content of the Upper Freeport coalbed in this western Pennsylvania demonstration area.

Jan 1, 1977

By D. A. Reynolds

The Bureau of Mines-American Gas Association survey of the carbonizing properties of American coals was begun in 1929, and has been continued almost without interruption since that time. Upwards of 100 coals have been carbonized at low, medium, and high temperatures in this survey, and about 200 additional coals have been carbonized at high temperatures only. All survey coals were blended with coal of different rank for carbonization at one high temperature (900° C,). During the past few years, 12-high-volatile A coals were blended with Pocahontas No 3 coal from Kimball, McDowell County, W. Va., and in this report the physical properties of the cokes from these high-volatile coals and their blends are compared.

Jan 1, 1949

By Sumner M. Anderson

ATHOUGH scattered signs of increased activity in the mining industry accompanied an incipient improvement in the overall economic situation during the latter months of 1963, production levels for the year as a whole responded to the general 1962-63 business recession with a 4.2 percent decline. The petroleum industry, active since 1907, did not become a dynamic force in the economy until exploration and drilling contracts were concluded with private companies in 1958 and 1959; on November 15, 1963, having virtually achieved self-sufficiency in petroleum in the preceding year, those contracts were unilaterally annulled. In the field of metallics, the only approach to internal sufficiency-aside from the iron and steel industry that has depended heavily on the importing of basic raw materials-has been in mining, smelting, and refining lead and zinc although iron ore, silver, beryllium, tantalite, and tungsten have been mine production items of economic significance. Reserves of lead, zinc, silver, bismuth, vanadium, and low-grade and metallurgically difficult iron ore-as well as those of beryllium, tantalite, and tungsten which are produced primarily for export-appear to be fairly abundant. The exploration of deposits of copper, cobalt, tin, lithium, gold, manganese and uranium has been undertaken on a relatively small scale, and little precise information is available on the extent of reserves. Argentina is dependent on foreign sources for part of its required iron and steel and, except for lead and zinc, most of its nonferrous metals. Nonmetallies and solid fuels present an exceptionally varied array of production items among which cement had the second largest 1963 output in South America. Borates, bentonite, common clay, diatomite, fluorite, granite, lime, limestone, obsidian, onyx, rhodochrosite, salt, and spodumene ordinarily are produced for export either exclusively or in excess of domestic consumption requirements. Barite, cement, chalk, gypsum, marble, and mica are both exported and imported. Argentina depends entirely or partly on imports for coal and coke, certain special types of clay, mineral abrasives, graphite, magnesite, mineral fertilizers, sulfur, talc, and minerals for construction, the last group being chiefly attributable to convenience of river transport from Uruguay.

Jan 1, 1964

By Ronald A. Vary

This paper is one of a series prepared by the United States Bureau of Mines dealing with milling methods and costs. In view of the current revival of interest in gold mining, information dealing with practices and costs in the development of gold properties is apropos. Milling practice at a small gold property in the prospect stage is described where, with a small outlay for plant and equipment, development has been carried on for about 20 months on the proceeds of the mill operation with little additional expenditure. The paper shows about what may be expected as to costs at a small property operated under northern climatic conditions and with rigid economy throughout the plant.

Jan 1, 1931

By Seymour Wasserman

To develop noise control designs for secondary crushers in Taconite plants. Taken into consideration: 1. Acoustical criteria 2. Day-to-day operational considerations and maintenance accessibility 3. Materials of construction 4. Adaptability of design to other Taconite plants having crushers 5. Cost of noise control treatment.

Jan 1, 1977

By Louis A. Panek

This report deals with the combined friction and suspension effects in the reinforcement of horizontally bedded mine roof by bolting. Other reports have treated these two effects separately. Friction effect refers to the reduction of bending in a laminated roof due to the clamping action of tensioned bolts. If the beds tend to have unequal deflections, the bolts oppose this tendency, thus creating a suspension effect, which consists of a transfer of part of the weight of weaker or thinner beds to the flexurally more rigid beds within the bolted unit. The combined effects of friction and suspension on the bending of the beds, whether an increase or a decrease, are difficult to generalize because they depend on the bedding sequence and the bolt pre-tension. Some analysis of the bedding sequence usually is required to determine the critical bed within a set of bolted beds. However, if the suspension effect is substantial and if the bolts are pre-tensioned, then the greatest bending stress is likely to occur in the thickest bed. Findings are based partly on theory and partly on tests of mine-roof models in a centrifuge, which were found to verify the theory. Mathematical formulas are obtained for the change in maximum roof bending stress and for the change of roof deflection due to the combined friction and suspension effects. The maximum bending stress is needed for designing a roof-bolting system and the deflection for evaluating its effectiveness.

Jan 1, 1962

By Deborah A. Kramer

As part of the Nation's growing concern with the competitiveness of U.S. firms in the world economy, especially with respect to advanced materials, the Bureau of Mines assessed the actual and potential recovery and manufacturing capabilities for gallium and gallium arsenide (Gacis). GaAs has advanced from a laboratory curiosity to a material with important "high-tech applications within only the last few years, and although protected North American gallium supplies are currently considered adequate, consumption could grow to the point that this assessment would need reevaluation.

Jan 1, 1988

By E. C. Lane

This report on properties of commercial motor fuels is the twelfth in a series made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the Interior. The first report contained data on motor gasolines sold during the winter of 1935-36.V The -present report, covering the summer of 1941, presents analytical data for 1,857 samples, representing the products of approximately 135 companies. As in previous surveys, these companies include both large and small suppliers. In addition, the Pacific coast is represented by data averaged by the Pacific Coast Technical Group before being submitted, and these data are published exactly as they were received. Conforming to previous surveys, the data cover three groups of samples -- regular-price, premium-price, and third-grade gasolines -- and each group has been aver aged separately. The number of samples, items, and brands comprising each group, exclusive of those of the Pacific coast, are as follows: Regular price, 1,010 samples, 291 items, and 86 brands; premium price, 577 samples, 263 items, and 78 brands; third-grade gasoline, 270 samples 159 items, and 74 brands. The meanings of these terms as used in the surveys are as follows: Sample: The individual supply of gasoline obtained at the filling station and analyzed in the laboratory.

Jan 1, 1942

By M. F. Chambers

The U.S. Bureau of Mines conducted experiments on electrowinning of neodymium metal by using a molten-metal cathode at 650° C and an electrolyte of 50 mol pct NdCl3 (neodymium chloride) and 50 mol pct KCI (potassium chloride). The molten-metal cathodes were alloys of magnesium and zinc or magnesium and cadmium. Current efficiencies were 90 pct with a Mg-Zn cathode and 80 pct with a Mg-Cd cathode; The Mg-Cd cathode was easily separated from the electrolyte. In contrast, the Mg-Zn cathode tended to mix with the electrolyte, making separation difficult. The cathode metals were separated from the neodymium by distillation at 1,100° C under a vacuum of 10-3 torr. Neodymium metal of 99.9+ purity was recovered from the Mg-Cd alloy cathode after 30 min distillation time. The neodymium recovered from the Mg-Zn system contained almost 2 pct Zn after vacuum distillation. Continuous operation using the Mg-Cd alloy cathode was demonstrated.

Jan 1, 2010

By Helen W. Lang

This report describes a monitoring system applied by the Bureau of Mines to provide rapid, continuous determination of the main constituents of exhaust gas during the Bureau's approval schedule testing of diesel engines for under-ground use. Commercially available continuous analyzers with strip chart readout are employed for nitric oxide (mass spectrometric), carbon dioxide (nondispersive infrared), methane (NDIR), carbon monoxide (NDIR), and oxygen (polarographic). Good correlation is obtained between the continuous instrumental results and those obtained by batch chemical and gas chromatographic methods.

Jan 1, 1969

By L. Mark Irwin, R. A. Marsyla

The objective of this laboratory investigation was to develop a mattesmelting process for the recovery of copper from industrial smelter dusts . Experimentation was conducted on three samples of Cottrell precipitator dust from a northern Michigan smelter with variations in the following conditions : Temperature , charge composition , pelletization , and moisture content . Based on chemical analyses of the furnace slags , poorest recovery of copper was effected in smelting dry charges regardless of composition . Some improvement was noted with uniformly moistened charges and still more with pelletized (but dry) mixes , but best results were obtained from smelting moist , self - fluxing pellets . Under favorable conditions , experiments yielded furnace slags with an average copper content of only 0.15 percent , which is well below that of industrial copper reverberatory slags .

Jan 1, 1963

By Rees D. Groves

The Bureau of Mines conducted research on reactions of copper sulfide minerals with chlorine in an aqueous system. Selected samples of covellite, chalcopyrite, chalcocite, bornite, and pyrite were leached with aqueous chlorine solutions. The mineral samples were sized on to minus 100- plus 325-mesh, individually mixed with precleaned sand and leached in an enclosed percolation column. Each mineral was leached in stages to achieve about 90 percent mineral dissolution. The chlorine leaching solutions were produced by reacting sodium hypochlorite with hydrochloric acid within the closed system. The study showed that when the mineral dissolution was complete, the reaction products (copper, iron, and sulfur) were in their highest oxidation states and a stoichiometric amount of chlorine was consumed. Although elemental sulfur formed as an intermediate product, it was oxidized to sulfate during the leach.

Jan 1, 1973

By P. F. Sands, Michael Sokaski, M. R. Geer

The purpose of this investigation was to determine the advantage of using either a conventional sieve bend ahead of a vibrating screen or of attaching a sieve - bend screen surface onto a vibrating screen to serve as a scalping deck when dewatering or draining dense medium from fine coal . In dewatering , use of either the sieve bend or scalping deck increased the capacity of the vibrating screen tenfold and the recovery of coal finer than 0.5 mm threefold , with no sacrifice in the moisture content of the oversize product . In dense -medium drainage , either the sieve bend or the scalping deck reduced the amount of magnetite retained on the product of the vibrating screen , particularly when the medium was as dense as that characteristic of the underflows from dense - medium cyclones . The sieve bend was slightly superior to the scalping deck in dewatering , but the scalping deck was clearly superior in dense -medium drainage . Additional advantages of the scalping deck are lower cost and a substantial saving in headroom.

Jan 1, 1963