Search Documents

By E. P. Youngman

This paper is one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate-mines in various foreign countries. This interpretation of the mining laws of Greece was prepared from information furnished by Ralph B. Curren, American assistant commercial attache, Athens, in reply to a questionnaire of the United States Bureau of Mines, transmitted through the courtesy of the commercial laws division of the Bureau of Foreign and Domestic Commerce. INTRODUCTION In his report,3 Mr. Curren states that the source of his information was the Director of Mines of the Greek Ministry of National Economy and the Mining Code of Greece, which was, compiled from existing laws in 1929,4 and which has since been modified by several acts of Parliament.

Jan 1, 1932

By T. A. Henrie, E. K. Kleespies

Carbon reduction of rutile and ilmenite in nitrogen and ammonia atmospheres was studied as a method of preparing titanium nitride . Ammonia was a better nitriding agent than nitrogen . The contact between the solid reactants , carbon and rutile , was a prime factor in nitrogen atmospheres and was of lesser import in dissociated ammonia . The reduction process for conversion of rutile to the nitride required carbon . The nitriding of ilmenite- carbon mixtures produced titanium nitride and elemental iron .

Jan 1, 1964

By J. E. Chilton

The U.S. Bureau of Mines has developed an intrinsically safe carbon monoxide (CO) monitoring system for mines by coupling a fiber-optic data telemetry (FODT) system with a prototype electro-chemical CO monitor. The CO monitoring system can be used in a coal mine as one component of an early fire warning system. This system may be used in belt haulage entries when the entries are used for supplying ventilation air to working places. The FODT accepts a 0.1-to 1.1-V analog signal from the monitor and converts it to pulses (0 to 5 V) at frequencies from 1.1 to 11 kHz that drive a light-emitting diode (LED). An electrically nonconducting fiber-optic cable carries the LED signal to a remote receiver. The receiver analyzes the incoming light signal and displays the measured CO concentration in parts per million. This report discusses the performance of the FODT system and characteristics of the CO monitor such as response times, linearity, and temperature and pressure effects.

Jan 1, 2010

By C. F. McCarroll

[Laboratory research and, control in the u?odnction an; utilization of petroleum and its product s have eqLmde& greatly during the past decade, rind much of the routine control and experimental equipment noirr requires the con-stant daily use of liquid nercury. In spite of this greater use, very little consideration has becn given to the hazard that might be occasioned by the toxic vapors of mercury unavoicl.a~l.p spilled or otherwise exposed to the atmosphere during the normcl 2rgced1u.e of ln30r~tor;~r operations. A sfmple visual exami~stion gf' sone of the laborztories reveals the prescnce of a considerable quantity of mercury in the craclcs of floors, on work tebles, ad on and mo7md eql~ipmeilt st.ads. Usually this yercurj ie contaminated with oily and dirt BO th~t it remint; in R finely divided state and a srnarl amount presents a relativell- lag? surface for evaporation. Since mercury shows meas~rable vo!-atility st a tempero.turc as lor^ 2s 8.5O F., mercury vapor will bo present in the atnosphere of anjr laboratory wbr.e mercury is exposed. promiscuously]

Jan 1, 1939

By Brian White, Hamid Maleki

Sudden, violent failures of rock around mine openings influence access, ventilation, and safety in both hard-rock and coal mines. To develop predictive tools for assessing the potential for violent failure, the authors initiated a comprehensive study using (1) multiple linear regression and numerical modeling analyses of geological and mining conditions at 25 sites to identify the most significant factors contributing to stress bumps in coal mines and (2) investigations of the geological and mining factors contributing to rock bursts in the Coeur d'Alene Mining District of northern Idaho, particularly the influence of preexisting structures on rock bursts. Twenty-five factors were initially considered in the study of coal bumps. The most important variables were identified as (1) mechanical properties of strata, (2) gate road geometry and/or gate pillar factors of safety, (3) roof beam thickness, joint spacing, and stiffness characteristics, and (4) stress gradients associated with previous mining and anomalous geologic conditions. In the Coeur d'Alene district, burst damage related to preexisting structures results primarily from (1) sudden buckling and crushing of rock layers where surfaces of development and production openings lie at low angles to bedding, faults, or other planar structures and (2) disturbance of loose ground caused by seismic fault-slip on preexisting faults or previously sheared bedding planes that intersect veins near pillar-stope margins.

By Fred C. Turin

The U.S. Bureau of Mines conducted a human factors analysis of hazards associated with roofholting activities in underground coal mines. Emphasis was placed on hazards related to the movement of the drill-head boom or mast of a roof bolting machine. The objective was to identify hazards and recommend solutions. The data-collection effort consisted of analysis of U.S. Mine Safety and Health Ad-ministration accident data; visits to underground mines and interviews with experienced roof bolting machine operators; discussions with roof bolting machine manufacturers; interviews with workers injured while performing roof bolting tasks; and reviews of research on roof bolting safety. A set of recommendations to increase the safety of roof bolting operations was developed. In particular, the following list of recommendations was presented in ranking order: (1) use an interlock device to cut off power to controls when an operator is out of position, (2) place fixed barriers at pinch points, (3) provide appropriate control guarding, (4) reduce fast-feed speed, (5) use automatic cutoff switches at pinch points, (6) redesign control bank to conform to accepted ergonomic principles, and (7) use resin insertion tools and resin cartridge retainers.

Jan 1, 2010

By T. H. Jeffers

The Bureau of Mines conducted laboratory tests to devise a procedure for extracting copper from low-grade discarded mill tailings. A solid extractant consisting of an organic solvent extraction reagent adsorbed on granular activated carbon was investigated and proved to be satisfactory for extracting copper directly from leach pulps. When this material was used in a cyclic leaching, stripping, and electrowinning pro-cess, 95 pct of the acid-soluble copper was recovered from oxidized mill tailings. The weathered tailings contained 0.24 pct Cu (total) and 0.20 pct acid-soluble Cu. The copper was recovered as cathodes containing, in parts per million, 1.6 Pb, 3.6 Fe, 0.5 Sb, 1.5 AI, 1.9 Mn, and <1 Mg.

Jan 1, 1985

By Emery Chilton, Charles Taylor, Mark Senk, Linda McWilliams

Three-axis ultrasonic anemometers are used to study airflow in the NIOSH ventilation gallery where ventilation in an underground mine is simulated. In this study, performance characteristics of this anemometer are evaluated and the effects of sensor orientation and sampler location on flow readings are examined. The study results provide guidelines for more effective use of the ultrasonic anemometers in the ventilation gallery.

By D. A. Wilson

A laboratory method for processing lead battery scrap has been developed that eliminates virtually all of the S02 emission that normally is produced when a reverberatory or blast furnace is used. The method employs a hydrometallurgical step to convert the PbS04 to PbO and CaS04 by mixing the battery scrap with a slurry of Ca(OH)2. The reaction is exothermic and goes to completion in 2 to 5 minutes at room temperature. The dried product is mixed with a KC1-NaC1 flux and carbon and reduced at 6500 C. A minimum charge ratio of 3 parts of carbon to 100 parts of battery scrap is required for reduction. The process produces lead reductions and recoveries as high as 97.0 and 94.9 percent, respectively. The KCI-NaCl flux is recovered using a standard counter-current water leach followed by evaporation.

Jan 1, 1976

By Anthony W. Sparks

The Bureau of Mines conducted tests designed to compare its breathing metabolic simulator (BMS) with other methods that are currently used to evaluate the performance of respiratory protective equipment. The BMS is a commercially developed device that uses a piston cylinder to simulate breath movement. Using a propane furnace that consumes oxygen and forms CO2, the BMS also simulates the respiratory metabolism of humans. The breathing and metabolic subsystems of the BMS are described in detail in this report. Results are compared from tests that used the BMS to evaluate respiratory equipment and from tests that used human subjects for the same purpose. The BMS was also tested against a pulsatile breathing machine (PBM) previously designed by the Bureau. Both machines were used to test respiratory equipment, and the test results are compared in this report. To illustrate typical applications of the BMS, the report briefly describes how the BMS was used to test two different types of closed-circuit respiratory apparatus, and the test results are presented. This research showed that BMS test results compared more closely to the results of tests that used human subjects than did results obtained using the PBM.

Jan 1, 1980

By M. P. Youker

USE OF LOW-PRESSURE GAS BURNERS IN OIL- FIELD BOILERS

Feb 1, 1922

By T. H. Dubaniewicz

Many mines rely on toxic gas sensors to help maintain a safe and healthy work environment. This report describes a prototype monitoring system developed by the U.S. Bureau of Mines (USBM) that uses light to power and communicate with several remote toxic gas sensors. The design is based on state-of-the-art optical-to-electrical power converters, solid-state diode lasers, and fiber optics. This design overcomes several problems associated with conventional wire-based systems by providing complete electrical isolation between the remote sensors and the central monitor. The prototype performed well during a 2-week field trial in the USBM Pittsburgh Research Center Safety Research Coal Mine.

Jan 1, 1995

By Van E. Shaw, D. J. Bauer

Conversion of euxenite concentrate to sulfates with sulfuric acid and solvent extraction of the yttrium- rare - earth mixture with EHPA were studied to determine extraction and separation characteristics . Digestion with 3.5 pounds of 96 percent sulfuric acid per pound of concentrate at 336 ° C for 4 hours resulted in an easily handled product with a yield in excess of 98 per- A thorium- free product was obtained by calcining the sulfated material for 3.5 hours at 650 ° C prior to leaching with water . Di ( 2 - ethylhexyl ) phosphoric acid solvent is an effective extractant with preference for cerium ( IV ) and heavy - group rare - earth elements including yttrium . Separation of complex rare - earth mixtures into light- and heavy - group fractions is feasible , and these fractions can be further processed to isolate ytterbium , neodymium , and dysprosium by changing processing conditions to obtain separation factors greater than two between these and adjacent elements .

Jan 1, 1965

By Dennis A. Long

Slip and fall accidents are a major cause of lost-time injuries associated with large mobile equipment in surface mines. An evaluation of the safety hazards associated with getting on and off large surface mining vehicles showed that most of the accidents occur at the point where personnel attempt to mount or dismount the machine at ground level. The major hazardous design conditions were identified as excessively flexible supports for lower steps or rungs, inappropriate ground-level-to-first-step distances, poor step designs, access designs that use vehicle components as steps or walkways, and inadequate hand- rail and guardrail designs, Additional hazards are introduced by the lack of proper maintenance of ladder hardware and the work practices of operators in carrying articles while mounting and dismounting the vehicle. This Bureau of Mines report describes the design and in-mine testing of improved access system for large mobile mining equipment.

Jan 1, 1984

By D. Harrington

Fire is always a serious-menace, whether in a residential or in an industrial region; in wartime it is particularly damaging in an industrial plant. The mining industry is especially vulnerable, as its plants are generally more or less isolated front centers of population and do not have access to modern fire-fighting equipment; moreover, owing to the transitory rapture of most mines, their surface structures; are often relatively flimsy and flammable.. Trained firemen seldom are available at or near mining plants to teach the fundamentals of fire-fighting to local fire brigades, with the result that efficiency in combating actual fires is lacking. Often the attitude "it can&apos;t happen here" is held by the management of a mining property, unless the plant has suffered a serious fire; even then lapse of time is very likely to induce forgetfulness as to the possible hazards. The necessity for producing metals for the prosecution of this war has increased management&apos;s responsibility. Whereas heretofore the loss of a plant or mill by fire meant merely monetary less to the stockholder of the company, now the national interest is affected, in that the nation suffers from loss of production of minerals indispensable for war purposes.

Jan 1, 1943

By J. H. East, D. Harrington

Fires in metal mines have resulted in some of the worst disasters in American mining history insofar as loss of life is concerned. One fire caused the death of 163 miners and individual less spectacular fires have cost the lives of scores of workers. Metal mines are often very deep, and the men working on numerous levels far removed from direct communication with the surface. In many instances they cannot be warned quickly of an emergency or a mine fire by telephone or other usual method of communication, or by messenger, flashing lights, gongs, sirens, or whistles. Telephones are not paricularly effective as a means of warning unless placed at all strategic points and with attendants always on duty; though telephones well placed have a definite value in any well-pla.mied emergency procedure in mines of all kinds. Messengers are slow and men working in remote parts of a mine would not receive a warning quickly enough. Most metal mines are not electrically lighted, except at or adjacent to shaft stations and in principal haulageways, and this limits the effectiveness of flashing lights. Electric gongs and sirens or whistles have been tried as warning signals, but the sound is quickly deadened and does not travel upward into the stopes, especially those of an extensive volume. Shutting off the compressed air is by no means satisfactory as a warning, as not infrequently it is stopped accidently, so that it loses its value as an alarm. The introduction of water into compressed air lines is undesirable as a fire warning and necessitates considerable care, especially in deep mines; pressure-reducing valves must be provided to reduce pressure that otherwise would break connections or split the pipe. A quick, effective method of warning miners underground of the existence of an emergency requiring them to leave the mine immediately, such as a fire on the surface or underground, is provided by the introduction of stenches in the compressed-air lines. This method of warning is by no means experimental, inasmuch as it has been used successfully for many years in

Jul 1, 1943

By Maurice J. Peterson

THE VISUAL-ARC spectroscopic method of rapid qualitative analysis of complex inorganic compounds has been popularized in the past few years and is being employed by an increasing number of laboratories. The mineralogy and chemistry departments of several universities recently have added visual spectroscopy to their laboratory curricula. This revival of interest in a somewhat dormant analytical method has been stimulated through the publication of three papers 4 by members of the College Park staff of the Bureau of Mines. These virtually are the only recent sources of information on visual-arc spectroscopic analysis. They include data on the spectroscopic assembly, the analytical procedure, and the practical application of the method to determinative mineralogy and related fields. Requests for reprints of these papers continue to be received; at present only a limited number of copies are available for distribution. In order that these requests may be adequately answered, material from the three papers has been combined and, with some additional data, is presented in this bulletin. Numerous specific inquiries have been received regarding types of equipment available, problems in instrumentation, and information on the approximate sensitivity limits of the elements that can be detected by this method. Some of this material was not included in the original papers. Accordingly, the table of wavelengths has been revised to include the approximate visual-arc spectroscopic sensitivities, and a section on commercially available equipment has been added.

Jan 1, 1953

By Robert L. Montgomery

Heats of solution of samarium (III) oxide and chloride in hydrochloric acid and of samarium (III) oxide, sulfate, and hydrated sulfate in sulfuric acid were measured. The heats of solution of this hygroscopic oxide are larger than those from the literature, probably because of more complete removal of water in the present study. From the literature value for the heat of combustion of samarium, the heats of formation of samarium (III) chloride and sulfate are -244.18 ± 0.41 and -928.5 ± 1.6 kcal./mole, respectively. The heat of hydration of the sulfate is -34.7 ± 1.0 kcal./mole. The heats of formation of other samarium com-pounds have been recalculated, using the new data.

Jan 1, 1959

By R. V. Lundquist, H. Leitch

Two hydrated calcium aluminates , formed by side reactions in the leaching step and desilication step of the lime- soda sinter process , were investigated to better define their influence on alumina recovery . The two calcium aluminates , Caз [ Al ( OH) 6 ]₂ and зCa0.Al½ 03 · ( 8-12 ) H₂ ) , were prepared and identified by chemical and X- ray analysis . The relative proportions of each of these compounds formed in typical leach solutions at several temperatures were determined . The influence of free lime as a promoter of calcium aluminate formation was also investigated . The formation and precipitation from leach liquors of calcium aluminates contributes to the low alumina recoveries in the process . The presence of carbonate ion in the leach solution suppresses calcium aluminate formation and precipitation and results in higher alumina recovery . Hydrated calcium aluminates are formed in the aging of lime - soda sinters in the normal atmosphere .

Jan 1, 1963

By W. W. Culter

"This paper is the outcome of thorough investigation into the value of the previous methods used for deriving production decline curves. It is highly important that methods be employed that are fundamentally sound and also practicably applicable. Six methods commonly used were studied. Some of these were found to be fundamentally in error; some save reliable curves but involved much work and time in the preparation; others gave reliable curves with less time and effort.It was found that of the methods previously employed the ""family curve"" method described in Bull. 134 Amer. Inst. Feb. 1918, pp. 499-500 by Lewis and Beal, was probably the most satisfactory. The now method given in this paper ploys the same principles as the ""family curve"" method, but is mathematical instead of graphical,The engineer and the oil man should carefully boar in mind both the use and the limitations of the average production curve such as is derived by the ""family curve"" method or other methods mentioned. Estimations of future productions or of underground oil reserves of a particular tract or well should be made from the production records of the tract or the well itself wherever such records are satisfactory. The use of the average curve of a district or field should be applied only to those properties or wells where there are not sufficient data to construct individual or tract production records, or where the productive life so short that a satisfactory individual record can not be obtained."

Jul 1, 1920